INSTALLATION INSTRUCTIONS: VERTICAL WALL BED HARDWARE KIT WITH FRAME MODEL CODES: 54877 (Single vertical wall bed) 55991 (Double vertical wall bed) 54386 (Queen vertical wall bed) *Our more compact model for shipping. Rockler Woodworking and Hardware 4365 Willow Drive, Medina, MN 55340 1-800-279-4441 1
HARDWARE A Left and right of the frame B Upper and lower half frame supports C Middle frame supports D Long center frame support x1 x1 x1 E Upper and lower frame supports F Flat bars G Pistons (non locking) H Mattress Supports x1 I Mounting plates (left and right) J Saddle locking plates K Brackets to attach wall bed to wall L Door brackets x6 x12 x12 M Legs (left and right) N Tube (for attaching legs) x1 x1 x1 O Slats 0 0 2 P Slat caps 0 0 2 Q Double slat caps 0 0 1 2
R Wrench x1 x1 x1 S1 Allen Key #4 x1 x1 x1 S2 Allen Key #5 x1 x1 x1 T Threaded inserts x16 x16 x16 U M8 x 16mm Screws x16 x16 x16 V #10 x 55mm Screws (Step 12) 6 6 6 W #8 x 15mm Screws (Steps 11-12) x32 x52 x52 X #10 x 15mm Screws Y #10 x 30mm Screws Z M5 x 15mm Screws AA M6 x 30mm Bolts BB M8x 50mm Bolts x34 x34 x34 CC Washers x8 x8 x8 DD Nylon Washers (for pivoting legs) EE M5 Nuts (for saddle locks) FF M8 Locking nuts 0 0 0 GG Temporary stoppers 3
Overall Cabinet Dimensions Cabinet Parts Dimension Guide F B C B C A A= Exterior B-C-D-E = Inset D B A A D B A Single Double Queen E E E E E 4 * Suggested dimensions
DRILLING GUIDE The holes should be 3/8 in diameter and 1/2 deep for threaded inserts. Back 11 7 16 " 6 1 8 " 7 3 4 " 2 1 2 " 2 1 2 " 9 7 16 " 6 15 16 " 3 1 8 " Front 11 7 16 " 13 7 8 " 17 3 4 " Bottom All measurements are for 3/4 thick board. *See full sized template in product box. 5
1 INSTALLING THE MOUNTING BRACKETS Front Right side I U T x16 x16 S2 Front Wood Left side I Bottom U + T 2 ASSEMBLING THE CABINET 6 * See guide on page 4 for suggested cabinet dimensions.
3 SECURING TO THE WALL X= Y= CC= K= x8 * Needs to be secured into at least two wood or metal studs. Y X *Nylon wall anchors are NOT recommended * Professional installation recommended. 4 ASSEMBLING THE FRAME S 4.1 Attach B and C to A for both the right and left sides of the frame. A B FF= x12 BB= A= B= C= x12 C *Ensure that all of the tabs are pointing towards each other. These tabs should be flat on the ground. B 7
4.2 Attach E and F to D. F E FF= BB= D= x1 D The tabs on E must face the inside of the frame. E= F= All tabs should be facing the floor. E F 4.3 Insert E into the assemblies from step 4.1. FF= BB= x6 x6 8
4.4 Bolt F to the two frame halves from step 4.1. FF= BB= x12 x12 5 INSTALLING THE SLATS P x36 O Q O x36 O P Q x18 Place P on one end of each slat. Attach two slats together with Q. Insert P and Q into their designated holes along the frame. Insert all of the slats except for 4 for the single and double, and 6 for the queen (please see next page to see which slats to skip). *If necessary, use a rubber mallet to secure the slats into the frame. 9
Example below works for both single and double. Please do not insert slats in row 11 for the queen 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Start from this side. Pivot point For each bed size, do not insert slats in row #8, or the slats in the last row. For the queen size, please do not insert slats in row #11 as well. #8 Pivot point Last 6 ATTACHING THE PISTONS TO THE FRAME FF= G= FF Secure the longer metal ends of the pistons to the frame. This end 10
7 INSTALLING THE FRAME ONTO THE MOUNTING BRACKETS Place the bearing into the saddle on the mounting bracket. Secure the bearing in place with: Z J EE 11
8 INSTALLING THE PISTONS TO THE CABINET Tilt the frame inside past the edge of the cabinet to install the pistons on the mounting brackets. FF 9 INSTALLING THE STOPPER Stopper Install the temporary stoppers GG onto the top corners of the bed cabinet. GG Install the permanent stopper on the inside top of the cabinet where it will allow for the door to close flush to the front of the cabinet. 12
M 10 INSTALLING THE LEGS FF DD 10.1 Secure the legs to the bed frame. Do not overtighten. AA M N 10.2 Install tube to both legs. AA AA S1 11 INSTALLING THE DOOR BRACKETS 6 6 The door brackets must point downward. Install the door brackets in alignment with the support bars on the bed frame. Top 10 3/8 10 3/8 * Install the handle on the other side of the door during this step. Decorative handle not included. Handle should be mounted at a height to comfortably allow the user to pull the bed down (approximately 1/3 of the way down from the top of the door). 27 5/16 30 3/4 Measurements (right) are for the placement of this hole on the backside of the doors. 27 5/16 30 3/4 W x12 x 24 L x 6 x12 Bottom 13
12 INSTALLING THE DOORS 12.1 Hook the door brackets onto the frame and push down until they are firmly in place. Center the doors on the frame. W V For this step x 2 12.2 Attach the doors to the frame while putting weight on the frame to keep the bed open. We recommend to have someone else sit on the frame during this step. W x 20 x 28 * The bed will not stay open on its own without the weight of a mattress. V x 26 x 26 14
13 INSTALLING THE REMAINING SLATS P O Q x6 x6 x3 O Q O P Insert P and Q into their designated holes along the frame. Insert all of the remaining slats. 14 INSTALLING THE MATTRESS SUPPORTS Insert the mattress supports into the designated holes on the bed frame. H H x 1 x 2 15
USING THE WALL BED The wall bed is assembled and shown in lowered position.. Pivot the leg towards the inside of the unit. Make sure that the leg is fully retracted. Pull up gently to close. The leg serves as a mattress retaining system. The pistons insure that the door closes properly and remains closed. * The bed will not stay open on its own without the weight of a mattress. Bed Size Mattress Size *Mattress not included Thickness Load Rating Dynamic Static Single 39 x 75 136 kg (300 lbs) Double 54 x 75 10. 154 kg (340 lbs) 454 kg (1000 lbs) Queen 60 x 80 181 kg (400 lbs) 16 RCKLR100KD-R2