2000-2400W Steam Iron User Instructions SHIR01
CONTENTS Introduction... 2 Product Safety... 3 Electrical Safety... 4 Features... 5 Instructions for Use... 5-7 Cleaning... 7 Troubleshooting... 7 Guarantee... 8 INTRODUCTION Thank you for purchasing this product You may already be familiar with using a similar product, but do please take time to read these instructions they have been written to ensure that you get the very best from your purchase. Safety is important To ensure your safety and safety of others, please ensure you read the Product Safety and Electrical Safety information before you operate this product. Please pay particular attention to any warnings and cautions contained in these instructions. Keep these instructions in a safe place for future reference. Due to our policy of continuous improvement, the actual product may differ slightly from the one illustrated in this booklet. 2
PRODUCT SAFETY IMPORTANT The mains lead of this product is not replaceable by the user. If the mains lead is damaged, the appliance should be taken to an authorised service centre, for repair. Please read these instructions carefully before using your iron for the first time and retain for future reference. Make sure that the voltage indicated on the rating plate is the same as your household supply. If not, do not use the iron and return it to the place of purchase. To protect against a risk of electric shock, do not immerse any part of the iron in water or any other liquids. Never yank the cord to disconnect from power outlet, always grasp the plug and pull to disconnect. Use iron only for its intended use. The iron should always be turned to min before plugging or unplugging from the outlet. Do not allow the cord to touch hot surfaces. Let the iron cool completely before putting it away. Loop cord loosely around the iron when storing. Always disconnect the iron from electrical outlet when filling with water or emptying and when not in use. Do not operate the iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Take it to an Approved Service Centre for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used. Close supervision is necessary for any appliance being used by or near children. Do not leave the iron unattended while connected to the mains or on an ironing board. Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down there may be hot water in the reservoir. If the iron is not operating normally, disconnect from the power supply and have the iron serviced by qualified service personnel. The iron must be used and rested on a stable surface. The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience or knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and and user maintenance shall not be made by children without supervision. Children should be supervised to ensure that they do not play with the appliance. The iron must not be left unattended while it is connected to the mains supply. The plug must be removed from the socked-outlet before the water reservoir is filled with water. When placing the iron on its stand, ensure that the surface on which the stand is placed is stable. 3
ELECTRICAL SAFETY IMPORTANT Read these instructions thoroughly before using this appliance or connecting it to the mains supply. A 13 amp BS1362 ASTA approved fuse must be fitted. This appliance must be earthed. There are no user-serviceable parts inside this appliance. Always refer servicing to qualified service personnel. The mains lead of this product is not replaceable by the user. If the mains lead is damaged, the entire appliance should be returned to the place of purchase. Do not allow this product to be exposed to rain or moisture during use or storage. Before switching on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. Connecting it to any other power source may cause damage. This product may be fitted with a non-rewireable plug. If it is necessary to change the fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement is obtained. If the plug has to be changed because it is not suitable for your socket, or due to damage, it should be cut off and a replacement fitted, following the wiring instructions shown. The old plug must be disposed of safely because inserting it into a 13 amp socket could cause an electrical hazard. The wires in the power cable of this product are coloured in accordance with the following code: Blue = Neutral Brown = Live Green/Yellow = Earth If the markings on the terminals of your plug do not correspond to the colours of the wires in the power cable, proceed as follows: The wire which is coloured Blue must be connected to the terminal which is marked N or coloured Black. The wire which is coloured Brown must be connected to the terminal which is marked L or coloured Red. The wire which is coloured Green/ Yellow must be connected to the terminal which is marked with the earth symbol ( ) or coloured Green, or Green/Yellow. 4
FEATURES Spray button Cord protector Steam dial Steam burst button Power indicator Rear cover Temperature control dial Filler cover Body Water tank Self-clean Spray head Plastic skirt Soleplate Power: 220-240V ~ 50/60Hz 2000-2400W INSTRUCTIONS FOR USE Using the iron for the first time When using the iron for the first time, you may notice a slight emission of smoke and hear some sounds made by the expanding plastics. This is normal and it stops after a short time. We also recommend passing the iron over an ordinary cloth before first use. Before using the iron for the first time, remove the plastic protector from the base (if it has one) clean the base with a soft cloth. Keep the base very smooth. Do not run it over metal objects (such as against the ironing board, buttons, zips, etc). Pure wool fibres (100% wool) can be ironed with the appliance in the steam position by preference select a high steam position and use a dry ironing cloth. Selecting the temperature Check the ironing instructions on the garment to be ironed. Fabrics that have some kind of finish (polishing. wrinkles, contrasts) can be ironed at the lowest temperatures. If the fabric contains several kinds of fibres, always select the temperature applicable, if an article contains 60% polyester and 40% cotton, you must always choose the temperature corresponding to polyester and without steam. 5
First classify the articles to be ironed according to the most suitable ironing temperature: Wool with wool, cotton with cotton, etc. As the iron heats up as fast as it cools, start by ironing the articles requiring the lowest temperature such as those made of synthetic fibres. Progress towards those that require the highest temperatures. Turn the temperature control dial until it is in front of the appropriate setting according to the following: position for nylon and acetate position for wool, silk or mixtures position for cotton or linen (steam) Filling the water tank Unplug the iron. Set the temperature control dial to dry ironing. Fill the tank through the filling hole. Do not fill past the maximum fill line. If you have hard water, it is advisable to use only distilled or demineralized water. Do not use chemically de-limed or perfumed water. Do not store the iron with water in the tank. Steam Ironing Fill the iron as described in section Filling the water tank. Plug the iron into the mains. Steam ironing is only possible when the highest temperatures shown on the temperature control dial are selected. Otherwise, water may escape through the soleplate. Wait until the pilot light goes out, which indicates that the selected temperature has been reached. Turn the temperature control dial to the required position. When the ironing is finished and during breaks in ironing, place the iron in its upright position. Disconnect the iron from the mains supply. Pour out any remaining water and leave the iron to cool down. Steam burst Steam burst gives extra steam for removing persistent creases. Place the temperature selector at the max position and wait until the pilot light goes out. Wait for a few seconds for the steam to penetrate the fibre before pressing again. NOTE : For the best steam quality, do not use more than three successive bursts each time. Several pumping actions are needed to start this function. Excessive use of this feature will cause the iron to cool, ensure that the pilot light is out, before operating the steam burst control. Anti-Drip System With the anti-drip system, you can perfectly iron even the most delicate fabrics. Always iron these fabrics at low temperatures. The plate may cool down to the point where no more steam comes out, but rather drops of boiling water that can leave marks or stains. In these cases, the Anti-drip system automatically activates to prevent vaporization, so that you can iron the most delicate fabrics without risk of spoiling or staining them. 6
Cleaning Disconnect the appliance from the mains before cleaning. Do not use solvents or abrasive products to clean the iron, clean with a damp cloth. The iron has a self-clean button. It is recommended to use this feature to clean the iron sole plate steam holes. To operate ensure that the water tank is full and set the temperature control dial to it s maximum setting. When the temperature ready light goes out, unplug the iron and hold it over a sink. Hold down the self- clean button. Strong bursts of steam will come from the base of the iron bringing with it any debris which has built up. Alternatively the above can be carried out over an old cloth. Troubleshooting IRON EMITS AN ODOUR OR SMOKE Iron gives off an odour when turned on for the first time. Oils used during manufacture need to be burnt off. Allow ten minutes for the odor to disappear. IRON DOES NOT HEAT The temperature control dial must be set at the desired temperature. IRON DOES NOT STEAM The water tank may be empty. Turn the temperature control dial to 0 and add water. Allow the iron to heat, and then set the dial to the steam setting. STEAM BURST FEATURE DOES NOT WORK The water tank must be at least 1/4 full. Temperature must be set to steam position. Iron should be in the horizontal position. Prime pump briefly. Allow a short pause between shots. Be sure to fully depress the steam burst button. IRON IS LEAKING The temperature setting is too low to produce steam. Steam burst used too much, allow iron to re-heat. 7
GUARANTEE This product is guaranteed for a period of 2 years from the date of original purchase when you simply register your product at: www.sensiohome.com Any defect that arises due to faulty materials or workmaniship during the first 12 months, will either be replaced or refunded where possible during this period by the dealer from whom you purchased the unit. NB: Non-registered products are guaranteed for a period of 12 months. If a fault develops after 12 months and within 24 months from the date of original purchase and you have registered the product on line, you should contact customer services quoting the product s model number and batch code. The following conditions apply: The guarantee does not cover accidental damage, misuse, cabinet parts, knobs or consumable items. The product must be correctly installed and operated in accordance with the instructions contained in this manual. It must be used only for domestic purposes. The guarantee will be rendered invalid if the product is re-sold or has been damaged by inexpert repair. Specifications are subject to change without notice. The manufacturer disclaims any liability for the incidental or consequential damages. The guarantee is in addition to, and does not diminish your statutory or legal rights. Valid in the UK only. Customer Helpline: 0345 467 6743 DISPOSAL INFORMATION Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority for recycling advice. For technical queries, please contact: MPL Home Ltd, IMEX, 575-599 Maxted Road, Hemel Hempstead, Herts, HP2 7DX MPL Home Ltd, IMEX, 575-599 Maxted Road, Hemel Hempstead, Herts, HP2 7DX 8 312987