AM54 Instruction Bulletin North American Installation Addendum Document Number PN25016 Armored Variable Area Flowmeter Series AM54331/32 Series AM54371/72/73/74 Series AM54431/32 Series AM54471/72/73/74 D184B114U04 Rev. 01 The purpose of this Addendum is to supplement or supersede information contained in the AM Instruction Bulletin D184B114U02 Rev. 00/08.2000
Instrument Designation AM54 Instruction Bulletin Part No. D184B114U04 Issue Date: 07/02 Revision: 01 Manufacturer: ABB Automation Products GmbH Dransfelder Str. 2 D-37079 Göttingen, Germany Telephone: +49 (0) 55 19 05-0 Telefax: +49 (0) 55 19 05-777 ABB Inc. 125 East County Line Road Warminster, PA 18974 USA Telephone: +1 215-674-6000 Telefax: +1 215-674-7183 Copyright 2002 by ABB Automation Products GmbH Revisions reserved This Instruction Bulletin is copyright protected. Translations, reproductions or distribution in any form - including editing and abstracts - and in particular, duplicating, photocopying, electronic distribution or storing in data processing installations or networks without the express consent of the copyright holder is strictly forbidden and may lead to civil or criminal proceedings. 2 AM54 D184B114U04
Table of Contents 1 Instrument Safety Standards.................................. 5 1.1 Safety standard of equipment.......................................... 5 1.2 Instructions for the use of pressure equipment functioning on the "measuring principle of suspended solid matter" 5 1.3 Technical limit values................................................ 5 1.4 Permissible measuring agents (fluids)................................... 6 1.5 Safety labels, symbols, data tags, factory tags and CE mark.................. 6 2 AM54 Model Number......................................... 7 3 Approvals.................................................. 8 3.1 FM Approvals...................................................... 8 3.2 CSA Approvals..................................................... 8 4 Installation Notes............................................ 9 4.1 Installation Information............................................... 9 4.2 Enclosure Grounding Information....................................... 9 4.3 Supply Wire Information.............................................. 9 4.4 Explosion Proof Installation Information.................................. 9 5 Intrinsic Safety Control Drawing.............................. 10 D184B114U04 AM54 3
4 AM54 D184B114U04
1 Instrument Safety Standards 1 Instrument Safety Standards 1.1 Safety standard of equipment The equipment corresponds to state-of-the-art technology and present safety rulings. It has been inspected and its technical safety condition was perfect when it left the factory. Please note the special information provided for commissioning the explosion-proof equipment version. You will find this in the Ex chapter of the main operating manual (Technical data of explosionproof version) The measurement equipment satisfies the EMC requirements defined in EN61326 / NAMUR NE21. For pressure equipment consisting of assemblies, we can only certify CE conformity for equipment in its delivery condition. Only the factory, service staff or an authorized specialist workshop may replace components. CE conformity will be voided if the operators themselves replace components 1.2 Instructions for the use of pressure equipment functioning on the "measuring principle of suspended solid matter" Pressure equipment functioning on the "measuring principle of suspended solid matter" are intended for carrying liquid, gaseous and steam media (fluids) and also satisfy the technical measurement task of measuring the operating volumetric flow under constant operating conditions (pressure, temperature, density). The flow measurement can also be output in standard or dimensional units. Correct usage includes: operations within technical limit values. compliance with information about the permissible measuring agents (fluids). compliance with information about assembly, operations, maintenance etc. The following are not permitted: operation as a flexible adapter in piping, e.g. to compensate for pipe offsets, pipe vibrations, pipe expansions etc.. use as a climbing aid, e.g. for assembly purposes. use as a support for external loads, e.g. as support for piping etc.. material loss e.g. by drilling the housing or material gain e.g. by painting over the factory panel/type plate or welding on or soldering parts. repairs, modifications and supplements or the installation of spare parts is only permitted if undertaken as described in the operating manual. More extensive work must be agreed with us beforehand. We assume no liability for unauthorized work. The operating, maintenance and repair conditions stated in this operating manual must be observed. The manufacturer assumes no liability for damage caused by usage which is unprofessional or incorrect. 1.3 Technical limit values The equipment is only designed for use within the technical limit values specified on the data tag and in the operating manual. The following technical limit values should be observed: the permissible pressure (PS) and the permissible temperature (TS) must be the pressure and temperature ratings specified in the supplement to this operating manual. The data on the factory tag / the data tag should be observed. The maximum and/or minimum operating temperature limits specified in the equipment specification must not be exceeded. D184B114U04 AM54 5
1 Instrument Safety Standards 1.4 Permissible measuring agents (fluids) Media may only be used if, depending on state-of-the-art technology or the operating experience of the operator, it can be assured that materials of the components coming into contact with the measuring agents (process connection, measurement pipes and flow distributors) assure a minimum of 15 years of successful operation. Media with unknown properties may only be used if the operator can perform regular and suitable tests to assure the safe condition of the equipment. 1.5 Safety labels, symbols, data tags, factory tags and CE mark All safety labels, symbols, the type plate and/or factory panel should be kept legible and replaced if damaged or lost. Note the following general information: Warning! Warning indicates possible injury to persons which could result in serious injury or death. Follow the instructions accurately to protect yourself and others. Caution! Note! Ex-protection CE mark Caution indicates possible damage to property which could result in incorrect operation or destruction of the equipment. Follow the instructions carefully to protect the equipment. Note indicates important activities or procedures which you MUST undertake correctly in order to prevent interrupts to operation or the function of the equipment. This symbol identifies equipment with Ex-protection. For usage in Ex-areas, you must observe the information provided in the "Ex-protection" chapter. The CE mark indicates that the equipment corresponds to the following guidelines and satisfies their fundamental safety requirements: CE symbol on the type plate (on the measurement transformer) Conformity with the EMC directive 89/336/EEC Conformity with the Ex Directive 94/9/ EC (only for equipment with Ex-protection) CE symbol on the factory panel (on the measurement transformer) Conformity with the PressureEquipmentDirective (PED) 97/23/EC The factory panel of pressure equipment does not include the CE mark, if e.g.: The max. permissible pressure (PS) is below 0.5 bar. A registration procedure is not required as a result of the low pressure risks (nominal width DN 25 / 1"). 6 AM54 D184B114U04
2 AM54 Model Number 2 AM54 Model Number AM543312 FM Approved Indicator with 4-20mA output signal without display AM543322 FM Approved Indicator with 4-20mA output signal with display AM543712 FM Approved Indicator only AM543722 FM Approved Indicator with minimum alarm signal AM543732 FM Approved Indicator with maximum alarm signal AM543742 FM Approved Indicator with minimum & maximum alarm signal AM544312 CSA Approved Indicator with 4-20mA output signal without display AM544322 CSA Approved Indicator with 4-20mA output signal with display AM544712 CSA Approved Indicator only AM544722 CSA Approved Indicator with minimum alarm signal AM544732 CSA Approved Indicator with maximum alarm signal AM544742 CSA Approved Indicator with minimum & maximum alarm signal Note - The 2 in position 6 of the model number indicates 1/2" NPT connector. D184B114U04 AM54 7
3 Approvals 3 Approvals 3.1 FM Approvals Explosion Proof Dust Ignition Proof Non-incendive Intrinsically Safe Class I, Division 1, Groups A, B, C, D Groups A & B require conduit seal within 18" of instrument Class II, Division 1, Groups E, F, G Class I, Division 2, Groups A, B, C, D Class I, Division 1, Groups A, B, C, D when connected per SD-10-4074 Class II, Division 1, Groups E, F and G and Class III 3.2 CSA Approvals Explosion Proof Dust Ignition Proof Intrinsically Safe Class I, Division 1, Groups B, C, D Class II, Division 1, Groups E, F, G Class I, Division 2, Groups A, B, C, D Class I, Division 1, Groups A, B, C, D when connected per SD-10-4074 Class II, Division 1, Groups E, F and G and Class III 8 AM54 D184B114U04
4 Installation Notes 4 Installation Notes 4.1 Installation Information Installation should be in accordance with ANSI/ISA RP12.6 "Installation of Intrinsically Safe Systems for Hazardous (Classified) Locations" and the National Electric Code (ANSI/NFPA 70) Sections 504, 505 and CEC, Canadian Electrical Code. 4.2 Enclosure Grounding Information Proper grounding of the AM54 enclosure is important for correct functioning as well as for safety reasons. For grounding purposes, an AWG#10 (or heavier) copper wire must be connected between the grounding screw located on the housing and the protective ground. 4.3 Supply Wire Information Unless otherwise instructed by local or national standards the recommended wire size to be used for supply wire is AWG#20. 4.4 Explosion Proof Installation Information AM54 Instruments installed using Explosion Proof method of protection in hazardous location groups A and B must be installed with conduit seals within 18" of the instrument. D184B114U04 AM54 9
5 Intrinsic Safety Control Drawing 5 Intrinsic Safety Control Drawing Hazardous (Classified) Location Nonhazardous Location AM5433/AM5443 Power Supply Circuit Optocoupler 31 32 41 + + FM Approved IS Barrier R B 4-20 ma Contact Output 42 FM Approved IS Barrier AM5437/AM5447 Proximity Sensor Proximity 41 42 51 + + FM Approved IS Barrier Sensor 52 FM Approved IS Barrier Intrinsic Safety Class I, Div 1, Groups A, B, C and D Class II, Div 1, Groups E, F and G and Class III This Document is controlled for Product Safety DO NOT CHANGE Without prior Approval of the Certifications Administrator, Dept 262 Entity Parameters: Models AM5433 / AM5443 Ambient Temperature Range: -55 C to +70 C 31/32 Vmax = 28 V Imax = 110 ma Pmax = 770 mw Ci = 6 nf Li = 204 uh 41/42 Vmax = 15 V Imax = 30 ma Pmax = 115 mw Ci = 3.6 nf Li = 102 uh Models AM5437 / AM5447 Ambient Temperature Range: IS -55 C to +60 C, NI -55 C to +40 C 41/42, 51/52 Vmax = 16V Imax = 20 ma Ci = 80 nf Li = 500 uh CAUTION: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY. DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS. Notes: 1. The Intrinsic Safety Entity concept allows the interconnection of two FM and CSA Approved Intrinsically safe devices with entity parameters not specifically examined in combination as a system when: Uo or Voc or Vt Vmax, Io or Isc or It Imax, Ca or Co Ci + Ccable, La or Lo Li + Lcable, Po Pi. 2. Dust-tight conduit seal must be used when installed in Class II and Class III environments. 3. Control equipment connected to the Associated Apparatus must not use or generate more than 250 Vrms or V DC. 4. Installation should be in accordance with ANSI/ISA RP12.6 "Installation of Intrinsically Safe Systems for Hazardous (Classified) Locations" and the National Electrical Code (ANSI/NFPA 70) Sections 504, 505 and CEC. 5. The configuration of associated Apparatus must be Factory Mutual Research and CSA Approved under Entity Concept. 6. Associated Apparatus manufacturer's installation drawing must be followed when installing this equipment. 7. No revision to drawing without prior Factory Mutual Research and CSA Approval. 8. Use shielded twisted pair cable ONLY (as shown above). Fig. 1: AM54 Intrinsic Safety Control Drawing 10 AM54 D184B114U04
Rights reserved to make technical revisions. This Instruction Bulletin is copyright protected. Translations, reproductions or distribution in any form - including editing and abstracts - and in particular, duplicating, photocopying, electronic distribution or storing in data processing installations or networks without the express consent of the copyright holder is strictly forbidden and may lead to civil or criminal proceedings. ABB Automation Products GmbH Dransfelder Str.2 D-37079 Göttingen, Germany Tel. +49 (0) 55 19 05-0 Fax +49 (0) 55 19 05-777 http://www.abb.de/durchfluss Rights reserved to make technical revisions Printed in the Fed. R. of Germany D184B114U04 Rev. 01 Issued 07/02