K GENERAL INFORMATION Wiegmann has always recognized that our customers in the electrical and electronic marketplace need reliable, high quality enclosures and environmental control products to meet their protection requirements. Protection Requirements today not only mandate NEMA TYPE, R,, & X, but also require a broad mix of BTU & size selections. Wiegmann is proud to offer those choices via a whole new line of A/C products. They are: Advantage Series, Trim Line Series, Micro-Mini Series, Integrity Series, and the Top Mount Series. Three Basic Cooling Methods When selecting a cooling method there are three types to consider. Passive Ventilation If there is only a minimal heat gain in your circumstance, use of louvers or grilles with filters can be effective. This method, however, usually provides less cooling effect than is necessary with today s components. Forced Convection Air Cooling If the installation will be in a clean, non-hazardous environment with an acceptable ambient (outside the enclosure) temperature range, a simple forced-air cooling system utilizing outside air is usually adequate. Combined with an air filter, such devices generally meet the heat removal needs of typical electronic equipment and many electrical applications (Fig. ). Examples of forced convection air cooling are filtered fans, fan trays, and blowers of various types. Closed-Loop Cooling In harsh environments involving high temperatures, wash-down requirements, heavy particulate matter or the presence of chemicals capable of damaging components (NEMA or environments), ambient air must be kept out of the enclosure. Closed-loop cooling consists of two separate circulation systems. One system, sealed against the ambient air, cools and recirculates the clean cool air throughout the enclosure. The second system uses ambient air or water to remove and discharge the heat. Examples of closed-loop cooling equipment employed with electronics and process controls are heat exchangers and air conditioners. FIGURE Forced Convection Method Filter & Grille Required Ambient Air with Heat Load Fan or Blower with filter & grille Ambient Air with Heat Load Ambient Air Fan or Blower with filter & grille Cabinet Ambient Air Filter & Grille Required Cabinet Pressurized System pushes air through enclosure Exhaust System pulls air through enclosure Fans and Blowers can be used to pressurize (preferred) or exhaust cabinet air. The ambient air should be filtered before it enters the cabinet. FIGURE - Closed Loop Cooling Method Heated Air Blower Ambient Air with Heat Load Condenser Heated Air Ambient Air with Heat Load Blowers Ambient Air Cooled Air Ambient Air Heat Exchanger Chilled Air Blower Evaporator In an air-to-air heat exchanger, heat from air surrounding the electronics is removed by a specially designed heat transfer element before being routed back into the enclosure. In air conditioners, a condenser, an evaporator, and two blowers combine to chill the air circulating in the enclosure.
AIR CONDITIONERS-APPLICATION INFORMATION K Cooling Control Cabinets Most electrical & electronic control systems generate a substantial amount of heat during operation. This heat factor is intensified as controls are made more compact, perform more functions, and are placed in more confined areas. Additional problems are encountered when the electronic process control system is located on-site in an industrial setting, rather than in a clean computer room. The factory environment can be hostile to the point that performance and effective life of the electronic components are materially reduced, or the control system fails completely. Ambient temperature might be excessively high, as that found in a steel mill. Moisture-laden air and air-borne particulate matter might be present to adversely affect the electronic components, as in the paper manufacturing industry. Air conditioners are designed to perform reliably under many of these harsh conditions and to provide the cooling and environmental protection required by sensitive electronic production control systems. Factors Affecting Model Selection This selection is presented as a basic outline or checklist of the various conditions to be considered when choosing a cooling unit for a certain application. The following are factors which must be considered when selecting a cooling unit: Internal Heat Load This is the heat dissipated by the electronic controls. It is expressed in watts. One watt equals. BTU/HR. Thus, to obtain the approximate cooling capacity required to remove a specific heat load, the following formula can be used: Watts x. = BTU/HR For example, a heat load of 800 watts requires an air conditioner capable of removing at least,70 BTU/HR. Resistance to Air Flow in the Enclosure Air Flow is measured in cubic feet per minute (CFM). To create an air flow of any desired velocity requires that pressure be produced by the blower in the air conditioner. Resistance to this blower-produced air flow is created by obstruction within the cabinet in the air flow path. The resistance itself is called pressure drop (P.D.) and is measured in inches of water column. The effect of significant restrictions in the cabinet air flow path are as follows: The obstructions cause pressure drops, which leads to cool air flow reduction. This reduction in cool air flow will decrease the effective capacity of the cooling unit. When selecting the proper cooling unit, allow-ance must be made for pressure drop. Heat Load From The Surroundings Ambient conditions can cause a heat gain in the enclosure. The rated capacity of the cooling unit must be sufficient to handle this heat gain. When evaluating the additional heat load gained from the surroundings, the subject more or less breaks down into two situations: () the cabinet is insulated and well sealed, or () the cabinet is not insulated (most cabinets are uninsulated.) () Cabinet Insulated Normally, well insulated cabinets will not gain sufficient ambient heat to affect air conditioner s operation. Maximum operating temperature for our air conditioners is 5 F. When the air conditioner operaties in ambient temperatures below 5 F, the cooling capacity of the air conditioner substantially increases. () Cabinet Not Insulated Obviously, this design placed more of a burden on the cooling unit. Heat is conducted to the cool side. Thus, high ambient heat will be readily transmitted into the cooler enclosure. To determine the additional capacity required of our air conditioner installed in an uninsulated cabinet, the surface square footage of the enclosure must be Cooling And Control Cabinets STEP ONE Watt =. BTU/HR. Determine the internal heat load in Watts that must be dissipated. STEP TWO m = 0.76 ft. Calculate the exposed surface area of the enclosure: (h x w ) + (h x d ) + (w x d ) = Area (ft) calculated to obtain the total effective heat transfer area. For this calculation, use the surface area of the sides, plus the area of the top, and omit the bottom area of the cabinet. Air movement outside the uninsulated cabinet will increase the heat conducted from the ambient into the enclosure. When there is little or no air circulation outside the cabinet, the layer of air immediately adjacent to the exterior cabinet walls acts as an insulating film. Exterior air movement dissipates this insulating layer of air in proportion to the velocity of the air flow. Substantial am-bient air circulation will increase the transmitted heat load imposed on the cooling unit. If the cabinet being cooled is not air tight, then high ambient relative humidity will adversely affect the cooling effectiveness of the air conditioner. When humid air infiltrates a poorly sealed enclosure, the air conditioner is required to use up valuable BTU/HR capacity just to condense the moisture from the internal air. Conversely, if the cabinet is well sealed, high ambient relative humidity, has very little effect on the heat capacity of the air conditioner. Steps For Sizing an Air Conditioner Proper selection of an air conditioner is determined by the following criteria: Required cooling capacity BTU/hr. (complete Steps #-) Mounting requirements (top or side mounting options) Dimension of air conditioner and enclosure STEP THREE oc or ok T=.8oF T Determine the temperature differential by subtracting the maximum allowable temperature inside the enclosure (Ti) from the maximum ambient temperature outside the enclosure (To) To-Ti= T STEP FOUR (Watts x.) + [.5 x Area ft. x T ( F)] =BTU/HR. Capacity Required BTU/HR. Capacity Rating
K M/TAB MOUNTING TEMPLATE AND ASSEMBLY Description A highlight of the Panel-Mounted TrimLine Series is an easy, revolutionary system for installing Panel-Mounted Air Conditioners and Heat Exchangers onto electronic or electrical enclosures. The M/TAB is standard on all TrimLine Air Conditioners. This integral system functions as a mounting template, preinstallation hanger and final assembly bracket. The M/TAB was specifically designed to assist in the difficult job of installing enclosure Air Conditioners. It simplifies the installation process by eliminating the problem of handling flange-mounted Air Conditioners. The solution is provided by following these installation steps... Use the M/TAB as a template to drill holes for mounting to the enclosure Bolt M/TAB to enclosure Cut out the Supply and Return openings Hang the Air Conditioner or Heat Exchanger on the M/TAB Secure the unit to the M/TAB The M/TAB also allows for the quick removal and transportation of the Air Conditioner or Heat Exchanger, separate from the equipment, for servicing or change to a different capacity samesize Air Conditioner or to a same-size Heat Exchanger. Features No exposed rails or mounting flanges; aesthetically pleasing while conserving cabinet space Reduction in installation time and labor, with significant cost savings Ease of installation and one piece design reduce mounting errors Allows the installer to operate independently Functions as a pre-installation hanger and final assembly bracket Installation is totally outside the enclosure; no clumsy mounting from inside the enclosure
INDOOR/OUTDOOR SIDE-MOUNTED AIR CONDITIONERS K5 NEMA TYPE R & MAINTAINED Description At last - air conditioners designed specifically for cooling electronic enclosures that can be used for both indoor and outdoor applications right out of the box! No more bulky unattractive weatherhoods... No more worries over what options to specify for outdoor applications. Expertly designed and crafted, the ADVANTAGE Series boasts a stylish appearance with rounded edges, no visible hardware and a textured baked powder finish to blend easily with contemporary enclosure designs. Serviceability has been made easier by incorporating a knock-down sheetmetal design which provides quick access to internal components. These air conditioners are available in capcities from,000 to,000 BTU/H in seven heights, all utilizing the exclusive M/TAB integral mounting system. Features Capacities:,000 to,000 BTU/H Textured Beige Powder Finish Built-in Condensate Evaporator CFC-Free Refrigerant Closed-Loop Cooling Crankcase Compressor Heater Digital Temperature Display EMI/RFI Suppressor Head Pressure Control Switch Heavy-duty Steel Enclosure Low Temperature Control Thermostat M/TAB Mounting System NEMA R and Ratings Maintained (UL50) Filters Six Foot [.8m] (minimum) SJT -wire Cord UL/CUL Recognized Complete line of accessories RP7,000 BTU/H 7"H x "W x "D RP8,000 BTU/H 8"H x "W x "D RP,000 BTU/H "H x "W x "D RP6 6,000 BTU/H 6"H x 5"W x "D RP7 8,000 &,000 BTU/H 7"H x 5"W x "D RP5 8,000 BTU/H 5"H x 7"W x 6"D RP55,000 BTU/H 55"H x "W x 7"D
K6 ADVANTAGE RP7 SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS.5 [.7] 7.50 [.5] 7. [5.] NEMA TYPE R & MAINTAINED FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE COOL AIR OUTLET TO ENCLOSURE 0.9 [77.8] Standard Features Condensate Evaporator CFC-Free Refrigerant Crankcase Compressor Heater Digital Temperature Display EMI/RFI Suppressor Head Pressure Control Switch Filters Low Temperature Control Thermostat M/TAB Mounting System NEMA R & Rating Maintained UL/CUL Recognized Textured Beige Powder Finish Accessories and Options Cooling Effect Detector Enclosure Heater Filter Recoating Adhesive Filters for replacement Internal corrosion protection Painted Metal Grille Power Loss Delayed Compressor Start Short Cycle Protector Special paint finishes Cooling Capacity (BTU/H) 000 500 000 500 000 PERFORMANCE CHART KACRP7R WACRP7R Maximum enclosure air temperature ºF 500 5 000 0 0 500 00 90 0 75 80 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded area not recommended. ADVANTAGE SERIES RP7 ADVANTAGE AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WACRP7R6 000 00 0/50 5/00 60/50 7.0/7.5 6 WACRP7R6 000 00 0/50 0/00 60/50.0 6 6 NEW PRODUCT IN 00 (6).8 [7.0] DIA. HOLES.05 [6.7] 0.5 [60.].0 [55.9].06 [5.].00 [5.].06 [7.0] MOUNTING PLAN 9. [6.5] (6).8 [7.0] DIA. HOLES 6.75 [7.5] 6.75 [7.5] 7.00 [77.8] 0.50 [.7] 6.5 [58.8] 7.50 [.5] 9.5 [.] 7.60 [9.0] 6.75 [7.5] 5. [8.] 6.75 [7.5] 7.00 [77.8] 6.5 [58.8] 9. [6.5].5 [8.9] 0.9 [77.9].56 [9.6].5 [.7].00 [5.] DIA. HOLE 6.8 [57.0] 0.56 [.] 0.5 [60.].5 [85.8] 0. [.] Dimensions, inches [metric], are for reference only and subject to change. UL/CUL Recognized models are available as Listed at added cost.. [56.]
ADVANTAGE RP8 SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS K7.5 [.7] 7.75 [70.9] 7.9 [695.6] FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE NEMA TYPE R & MAINTAINED COOL AIR OUTLET TO ENCLOSURE 0.9 [77.8] Standard Features Condensate Evaporator CFC-Free Refrigerant Crankcase Compressor Heater Digital Temperature Display EMI/RFI Suppressor Head Pressure Control Switch Filters Low Temperature Control Thermostat M/TAB Mounting System NEMA R & Rating Maintained UL/CUL Recognized Textured Beige Powder Finish Accessories and Options Cooling Effect Detector Enclosure Heater Filter Recoating Adhesive Filters for replacement Internal corrosion protection Painted Metal Grille Power Loss Delayed Compressor Start Short Cycle Protector Special paint finishes Cooling Capacity (BTU/H) PERFORMANCE CHART KACRP8R WACRP8R 6000 550 500 Maximum enclosure air temperature ºF 750 000 5 50 0 500 750 0 00 90 0 75 80 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded area not recommended. ADVANTAGE SERIES RP7 ADVANTAGE AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WACRP8R6 000 0 5/50 5/00 60/50 9.8/9.7 86 WACRP8R6 000 0 5/50 0/00 60/50 5.5/5.6 86 6 NEW PRODUCT IN 00.9 [8.5] 9.00 [8.6].67 [.].68 [.7] MOUNTING PLAN 9.00 [8.6] (8).8 [7.0] DIA. HOLES 8.00 [0.] 6.50 [65.] 0.7 [58.] 8.00 [0.] 6.50 [65.].88 [7.] 7.75 [70.8] 8.6 [9.] 7.75 [70.9].88 [7.] 5.00 [7.0] 8.59 [7.9].8 [6.7] 5.00 [7.0].8 [9.9] 0.00 [5.0].78 [5.] 0.9 [77.8].50 [8.].5 [.6] 6. [57.7].00 [5.] DIA. HOLE.8 [0.0] 0.00 [5.0].5 [.7].78 [5.].5 [6.7] UNIT MUST BE [00mm] MINIMUM ABOVE FLOOR FOR FILTER ACCESS Dimensions, inches [metric], are for reference only and subject to change. UL/CUL Recognized models are available as Listed at added cost.
K8 ADVANTAGE RP SERIES AIR-COOLED SIDE MOUNT AIR CONDITIONERS.5 [.7].75 [8.9].9 [8.7] FILTERED CONDENSER AIR INLET (Ambient Air In) NEMA TYPE R & MAINTAINED CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE COOL AIR OUTLET TO ENCLOSURE 0.9 [77.8] Standard Features Built-in Condensate Evaporator CFC-Free Refrigerant Crankcase Compressor Heater Digital Temperature Display EMI/RFI Suppressor Head Pressure Control Switch Filters Low Temperature Control Thermostat M/TAB Mounting System NEMA R & Rating Maintained UL/CUL Recognized Textured Beige Powder Finish Accessories and Options Cooling Effect Detector Enclosure Heater Filter Recoating Adhesive Filters for replacement Internal corrosion protection Painted Metal Grille Power Loss Delayed Compressor Start Short Cycle Protector Special paint finishes Cooling Capacity (BTU/H) 9600 800 700 6000 800 PERFORMANCE CHART KACRPR WACRPR Maximum enclosure air temperature ºF 600 5 00 0 0 00 80 90 0 75 00 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded area not recommended. WDTS SERIES 500 BTU SIDE MOUNT AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WACRPR6 000 850 5/50 5/00 60/50.6/. 98 WACRPR6 000 850 5/50 0/00 60/50 5.8 98 6 NEW PRODUCT IN 00.0 [5.8] 0.5 [60.].05 [6.7].7 [69.].0 [5.8] MOUNTING PLAN 0.5 [60.].05 [6.7].7 [69.] 9.6 [.].00 [0.6].5 [9.] 9.6 [.].00 [0.6] (8).8 [7.0] DIA. HOLES 6.50 [9.].75 [8.9] 8.5 [6.9] (8).8 [7.0] DIA. HOLES 6.50 [9.].8 [6.7] 7.75 [96.9] 0.50 [66.7].8 [6.7] 7.75 [96.9].8 [0.0] 9.00 [8.6] 0.00 [5.0].68 [.7].78 [5.] 0.9 [77.9].56 [9.6].5 [.7] 6.8 [57.0].8 [0.0] 9.00 [8.6] 0.00 [5.0].68 [.7].78 [5.].00 [5.] DIA.HOLE. [6.7] UNIT MUST BE [00mm] MINIMUM ABOVE FLOOR FOR FILTER ACCESS Dimensions, inches [metric], are for reference only and subject to change. UL/CUL Recognized models are available as Listed at added cost.
ADVANTAGE RP6 SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS K9 5.5 [89.9] 6.75 [955.5] 6.0 [9.0] FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE NEMA TYPE R & MAINTAINED COOL AIR OUTLET TO ENCLOSURE 0.9 [77.8] Standard Features Built-in Condensate Evaporator CFC-Free Refrigerant Crankcase Compressor Heater Digital Temperature Display EMI/RFI Suppressor Head Pressure Control Switch Filters Low Temperature Control Thermostat M/TAB Mounting System NEMA R & Rating Maintained UL/CUL Recognized Textured Beige Powder Finish Accessories and Options Cooling Effect Detector Enclosure Heater Filter Recoating Adhesive Filters for replacement Internal corrosion protection Painted Metal Grille Power Loss Delayed Compressor Start Short Cycle Protector Special paint finishes Cooling Capacity (BTU/H) 9600 800 700 PERFORMANCE CHART KAC6RP6R WAC6RP6R Maximum enclosure air temperature ºF 6000 800 5 0 600 0 00 00 90 00 80 0 75 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded area not recommended. ADVANTAGE SERIES RP6 ADVANTAGE AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WAC6RP6R6 6000 500 5/50 5/00 60/50 9.5/0.0 WAC6RP6R6 6000 500 5/50 0/00 60/50 9.5/0.0 6 NEW PRODUCT IN 00 MOUNTING PLAN.0 [7.9].6 [.].0 [7.9].6 [.].88 [.0].88 [.0] ().8 [7.0] DIA. HOLES 6.75 [7.5] 5.75 [6.] 7.75 [96.9] 8.96 [75.6] 6.75 [9.5] 6.0 [9.0] ().8 [7.0] DIA. HOLES 6.75 [7.5] 5.75 [6.] 7.75 [96.9] 8.96 [75.6]. [6.].8 [6.7].50 [7.5].8 [6.7].5 [6.6].56 [9.6] 5. [89.6]. [6.].8 [6.7].50 [7.5].8 [6.7] UNIT MUST BE [00mm] MINIMUM ABOVE FLOOR FOR FILTER ACCESS Dimensions, inches [metric], are for reference only and subject to change. UL/CUL Recognized models are available as Listed at added cost.
K0 ADVANTAGE RP7 SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS NEMA TYPE R & MAINTAINED Standard Features Built-in Condensate Evaporator CFC-Free Refrigerant Crankcase Compressor Heater Digital Temperature Display EMI/RFI Suppressor Head Pressure Control Switch Filters Low Temperature Control Thermostat M/TAB Mounting System NEMA R & Rating Maintained UL/CUL Recognized Textured Beige Powder Finish FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE COOL AIR OUTLET TO ENCLOSURE 6.75 [955.5] 5.5 [89.9] 0.9 [77.8] 6.0 [9.0] Accessories and Options Cooling Effect Detector Enclosure Heater Filter Recoating Adhesive Filters for replacement Internal corrosion protection Painted Metal Grille Power Loss Delayed Compressor Start Short Cycle Protector Special paint finishes Cooling Capacity (BTU/H) Cooling Capacity (BTU/H) KAC8RP7R WAC8RP7R 6000 000 Maximum enclosure air temperature ºF 000 0000 8000 5 6000 0 0 000 000 0 00 90 75 70 80 90 00 0 0 0 Ambient Temperature (ºF) 6000 000 000 0000 8000 6000 000 000 PERFORMANCE CHART KACRP7R WACRP7R Maximum enclosure air temperature ºF 5 0 0 00 90 75 80 0 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded area not recommended. ADVANTAGE SERIES RP7 ADVANTAGE AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WAC8RP7R6 8000 6600 5/50 5/00 60/50./.7 50 WAC8RP7R6 8000 6600 5/50 0/00 60/50 5.7/5.9 50 WACRP7R6 000 8500 5/50 5/00 60/50 9.8/9. 50 WACRP7R6 000 8500 5/50 0/00 60/50 9./9.0 50 6 NEW PRODUCT IN 00. [6.] 5.5 [89.9].50 [7.5]. [6.].50 [7.5] 7.00 [77.8] 7.00 [77.8] ().8 [7.0] DIA. HOLES 7.75 [70.9] 7.5 [00.] ().8 [7.0] DIA. HOLES 7.75 [70.9] 7.5 [00.] 6.8 [89.0] 7.00 [77.8] 7.75 [96.9] 7.00 [77.8] 7.75 [96.9]. [79.5].0 [7.9].50 [7.5].6 [.].8 [6.7]. [79.5].0 [7.9].50 [7.5].6 [.] Dimensions, inches [metric], are for reference only and subject to change..8 [6.7].5 [6.6] UNIT MUST BE [00mm] MINIMUM ABOVE FLOOR FOR FILTER ACCESS 5.5 [89.9] UL/CUL Recognized models are available as Listed at added cost.
TRIMLINE SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS K NEMA TYPE MAINTAINED Description Innovations in technology have resulted in much denser components packaging and smaller available panel sizes on which to mount Air Conditioners. The TrimLine Series is the response to these new packaging demands with the Narrow 0", ", 5" and 7" width panel-mount air conditioners. In addition to being narrower than traditional Air Conditioner units, the TrimLine Series include the Condensate Evaporator, Low Temperature Control Thermostat and EMI/RFI Suppressor as standard features and are available in all popular voltages and frequencies. The TrimLine Series consists of compact models in,000-,500 BTU/H capacities, mid-size models, 8", " and 6" WITH up to,000, 5,000 and 6,000 BTU/H respectively and the fullsize model at 7" with 0,000 BTU/H. Each model series is designed with a minimum width to take up less cabinet space on the exterior panel or door. Integral to the TrimLine Series is the M/TAB (Mounting Template and Assembly Bracket) system which makes installing Air Conditioners simple and fast and interchangeable with corresponding TrimLine Heat Exchangers. Outdoor or corrosive environments require weather protection and/or special internal and external protective features. For outdoor applications see the Advantage and Integrity Outdoor Series. For extreme ambient temperatures and/or severely contaminated environments, the use of TrimLine or other Water-Cooled Air Conditioners are recommended. Features Capacities:,000 to 0,000 BTU/H; six heights available CFC-free or Low ODP Refrigerant All models UL/CUL Listed or Recognized Tested and approved by UL for NEMA Enclosures Compact design with slim 0", ", 5" and 7" wide mounting footprints Exclusive KOOLTRONIC M/TAB integral mounting system for quick, easy installation Built-in Condensate Evaporator eliminates need for draining normal condensate Thermostatic Low Temperature Control prevents over-cooling and provides energy-efficient operation EMI/RFI Suppressor minimizes transient line spikes during on/off cycling Field-reversible condenser outlet blower provides choice of horizontal or vertical air discharge Heavy-duty steel enclosures with gray baked powder finish Six foot (minimum) SJT -wire power cord Complete line of accessories NP7,000 BTU/H 7 H x W x 9 D Narrow-Mini,500 BTU/H 0 H x 0 W x 0 D NP8,000 BTU/H 8 H x W x D NP,000 BTU/H H x W x 9 D NP6,000 & 6,000 BTU/H 6 H x 5 W x D NP7 7,000, 8,000, 0,000,000 BTU/H 7 H x 5 W x D
K TRIMLINE NP7 SERIES SIDE-MOUNTED AIR CONDITIONERS THERMOSTAT ADJUSTMENT ACCESS. [08.] M/TAB FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE COOL AIR OUTLET TO ENCLOSURE 9.00 [8.6] 7.50 [.5] Standard Features Built-in Condensate Evaporator CFC-Free Refrigerant EMI/RFI Suppressor Low Temperature Control Thermostat M/TAB Mounting System NEMA Rating Maintained (UL50) UL/CUL Listed Gray Powder Finish Accessories and Options Cooling Effect Detector NEMA TYPE MAINTAINED Filter Recoating Adhesive Filters for replacement Internal corrosion protection Lifting Eyes Low Ambient Kit Short Cycle Protector Special materials or finishes Special motors, line cords, or connectors Stainless or Aluminum Cabinet Weather Protection Kit.5 [.] Cooling Capacity (BTU/H) PERFORMANCE CHART KAC.0NP7L WAC.0NP7L 000 500 000 Maximum enclosure air temperature ºF 500 000 5 500 0 000 500 0 75 0 00 90 80 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded area not recommended. TRIMLINE SERIES NP7 AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WAC0NP7L6 000 0 5/50 5/00 60/50 6.7/6.5 59 WAC0NP7L6 000 0 5/50 0/00 60/50. 59 6 NEW PRODUCT IN 00 MOUNTING PLAN (6) / -0 WELD NUTS M/TAB 9.00 [8.6] FILTER 0.50 [.7] 0.50 [.7].5 [.].5 [85.8] 6. [55.7]. [79.5] 0.8 [9.5] 6' [.8M] MIN. POWER CORD 7.50 [.5] 8. [06.5] 5.00 [7.0]. [0.9] 7.50 [.5] 6.8 [6.] 0.8 [9.5] O.D. CONDENSATE DRAIN. [08.] 0.8 [9.5] (8). [7.9] DIA HOLES 5.75 8 8 [6.] 0.88 0.8 [.] [9.5] Dimensions, inches [metric], are for reference only and subject to change. Weld-nut mounting method, without M/TAB Weld nuts supplied for alternate mounting method to maintain NEMA. Mounting Plans furnished on request.
TRIMLINE NP8 SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS K 0. [57.] M/TAB THERMOSTAT ADJUSTMENT ACCESS FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE COOL AIR OUTLET TO ENCLOSURE 8.50 [7.9] NEMA TYPE MAINTAINED.50 [9.] Standard Features Built-in Condensate Evaporator CFC-Free Refrigerant EMI/RFI Suppressor Low Temperature Control Thermostat M/TAB Mounting System NEMA Rating Maintained (UL50) UL/CUL Listed Gray Powder Finish Accessories and Options Cooling Effect Detector Filter Recoating Adhesive Filters for replacement Internal corrosion protection Lifting Eyes Low Ambient Kit Short Cycle Protector Special materials or finishes Special motors, line cords, or connectors Stainless or Aluminum Cabinet Weather Protection Kit KACNP8L WACNP8L 8000 7000 6000 Maximum enclosure air temperature ºF 5000 000 5 000 0 000 0 00 000 0 75 90 80 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded area not recommended. Cooling Capacity (BTU/H) PERFORMANCE CHART TRIMLINE SERIES NP8 AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WACNP8L6 000 50 5/50 5/00 60/50.0/.0 85 WACNP8L6 000 50 0/50 0/00 60/50 6.0 85 6 NEW PRODUCT IN 00 MOUNTING PLAN 6' [.8M] MIN. POWER CORD M/TAB.50 [9.] CONDENSATE DRAIN IN BOTTOM. [8.9] 7.00 [77.8].57 [9.8] 0.6 [6.] FILTER 7.75 [96.8].9 [60.7] 8.50 [7.9].9 [06.]. [86.6].76 [70.] 7.75 [96.8].0 [09.].9 [7.] 7.50 [90.5] (8). [7.9] DIA. HOLES.6 [9.6] 0. [57.].50 [8.] 7.00 [77.8] 8.00 [0.].07 [7.] Dimensions, inches [metric], are for reference only and subject to change.
K TRIMLINE NP SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS.50 [7.5] M/TAB FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE COOL AIR OUTLET TO ENCLOSURE.88 [85.] THERMOSTAT ADJUSTMENT ACCESS NEMA TYPE MAINTAINED 9.50 [.] Standard Features Built-in Condensate Evaporator CFC-Free or Low ODP Refrigerant EMI/RFI Suppressor Low Temperature Control Thermostat M/TAB Mounting System NEMA Rating Maintained (UL50) Reversible Condenser Outlet Blower UL/CUL Listed Gray Powder Finish Accessories and Options Cooling Effect Detector Enclosure Heater Filter Recoating Adhesive Filters for replacement Internal corrosion protection Lifting Eyes Low Airflow Detector Low Ambient Kit Short Cycle Protector Special materials or finishes Special motors, line cords, or connectors Stainless or Aluminum Cabinet Weather Protection Kit KACNPL WACNPL 8000 7000 6000 Maximum enclosure air temperature ºF 5000 000 5 000 0 000 0 00 000 0 75 90 80 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded area not recommended. Cooling Capacity (BTU/H) PERFORMANCE CHART TRIMLINE SERIES NP AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WACNPL6 000 680 5/50 5/00 60/50.8 90 WACNPL6 000 680 5/50 0/00 60/50 7.0 90 6 NEW PRODUCT IN 00 MOUNTING PLAN.0 [5.8] 0.5 [60.].05 [6.7].7 [69.].0 [5.8] 0.5 [60.].05 [6.7].7 [69.] 9.6 [.].00 [0.6].5 [9.] 9.6 [.].00 [0.6] (8).8 [7.0] DIA. HOLES 6.50 [9.].75 [8.9] 8.5 [6.9] (8).8 [7.0] DIA. HOLES 6.50 [9.].8 [6.7] 7.75 [96.9] 0.50 [66.7].8 [6.7] 7.75 [96.9].8 [0.0] 9.00 [8.6] 0.00 [5.0].68 [.7].78 [5.] 0.9 [77.9].56 [9.6].5 [.7] 6.8 [57.0].8 [0.0] 9.00 [8.6] 0.00 [5.0].68 [.7].78 [5.].00 [5.] DIA.HOLE. [6.7] Dimensions, inches [metric], are for reference only and subject to change.
TRIMLINE NP6 SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS K5 5.9 [85.8] NEMA TYPE MAINTAINED Standard Features Built-in Condensate Evaporator CFC-Free Refrigerant EMI/RFI Suppressor Low Temperature Control Thermostat M/TAB Mounting System NEMA Rating Maintained(UL50) Reversible Condenser Outlet Blower UL/CUL Listed/Recognized Gray Powder Finish Accessories and Options Cooling Effect Detector FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE COOL AIR OUTLET TO ENCLOSURE Filter Recoating Adhesive Filters for replacement Internal corrosion protection Lifting Eyes Low Ambient Kit Low Airflow Detector Short Cycle Protector Special materials or finishes Special motors, line cords, or connectors Stainless or Aluminum Cabinet Weather Protection Kit 6.75 [9.5].5 [.] Cooling Capacity (BTU/H) Cooling Capacity (BTU/H) KACNP6L WACNP6L 8000 7000 Maximum enclosure air temperature ºF 6000 5000 000 5 0 000 0 00 000 000 90 80 75 0 70 80 90 00 0 0 0 Ambient Temperature (ºF) 8000 7000 6000 PERFORMANCE CHARTS KAC6NP6R WAC6NP6R Maximum enclosure air temperature ºF 5000 5 000 0 0 000 00 000 90 000 80 75 0 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded areas not recommended. TRIMLINE SERIES NP6 AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WACNP6L6 000 700 5/50 5/00 60/50.5 5 WACNP6L6 000 700 5/50 0/00 60/50 7.5 5 WAC6NP6R6 6000 00 5/50 5/00 60/50 6.5/7.0 5 WAC6NP6L6 6000 00 5/50 0/00 60/50 8. 5 6 NEW PRODUCT IN 00 (OPTIONAL) MOUNTING PLAN 6' [.8M] MIN. POWER CORD M/TAB.5 [.].50 [8.] 5.06 [8.6].00 [0.8] THERMOSTAT.00 [0.8] 6.75 [9.5] (0). [7.9] DIA. HOLES 6.75 [7.5] 9.8 [9.] 6.75 [9.5] 8.5 [09.6] CONDENSATE DRAIN FILTER 5.9 [85.8].5 [.8] 0.88 [.].50 [7.5]. [8.].00 [76.] 0.75 [9.] Dimensions, inches (metric), are for reference only and subject to change. UL/CUL Recognized models are available as Listed at added cost.
K6 TRIMLINE NP7 SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS THERMOSTAT ADJUSTMENT ACCESS 5.9 [85.8] FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE COOL AIR OUTLET TO ENCLOSURE NEMA TYPE MAINTAINED M/TAB 7.5 [00.].5 [.] Cooling Capacity (BTU/H) PERFORMANCE CHARTS KAC8NP7R WAC7NP7L 000 0500 Maximum enclosure air temperature ºF 9000 7500 6000 5 500 0 0 000 500 0 00 90 80 75 70 80 90 00 0 0 0 Ambient Temperature (ºF) Standard Features Built-in Condensate Evaporator CFC-Free or Low ODP Refrigerant EMI/RFI Suppressor Low Temperature Control Thermostat M/TAB Mounting System NEMA Rating Maintained (UL50) Reversible Condenser Outlet Blower UL/CUL Listed/Recognized Gray Powder Finish Accessories and Options Cooling Effect Detector Deep Drain Pan Kit Enclosure Heater Filter Recoating Adhesive Filters for replacement Internal corrosion protection Lifting Eyes Low Airflow Detector Low Ambient Kit Short Cycle Protector Special materials or finishes Special motors, line cords, or connectors Stainless or Aluminum Cabinet Weather Protection Kit KACNP7R WAC0NP7R 500 000 Maximum enclosure air temperature ºF 0500 9000 5 7500 0 6000 0 00 500 000 90 80 75 500 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded areas not recommended. Cooling Capacity (BTU/H) TRIMLINE SERIES NP7 AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WAC6NP7L6 6000 600 5/50 5/00 60/50 6.5 50 WAC6NP7L6 6000 600 5/50 0/00 60/50 8.6 50 WAC7NP7L6 7000 750 5/50 5/00 60/50 6.5 50 WAC7NP7L6 7000 750 5/50 0/00 60/50 8.6 50 WAC8NP7L6 8000 750 5/50 5/00 60/50 6.5 50 WAC8NP7L6 8000 750 5/50 0/00 60/50 8.6 50 WAC0NP7R6 0000 750 0/50 5/00 60/50 9./8.6 60 WAC0NP7L6 0000 750 5/50 0/00 60/50.8 60 WACNP7R6 000 750 0/50 5/00 60/50 9./8.6 60 WACNP7L6 000 750 5/50 0/00 60/50.8 60 6 NEW PRODUCT IN 00 MOUNTING PLAN (OPTIONAL).5 [.] M/TAB 6' [.8M] MIN. POWER CORD 0.88 [.].50 [8.].8 [76.]. [8.].00 [0.7] 8.00 [57.] FILTER 7.5 [00.] (). [7.9] DIA. HOLES 7.00 [77.8].88 [606.] 6.6 [8.] 0. [57.] 0.75 [9.0] 5.9 [85.8] OPTIONAL CONDENSATE DRAIN CONDENSATE DRAIN.5 [.8].50 [7.5].00 [76.] Dimensions, inches [metric], are for reference only and subject to change. UL/CUL Recognized models are available as Listed at added cost.
MICRO-MINI SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS K7 THERMOSTAT ADJUSTMENT ACCESS.5 [6.6] FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE COOL AIR OUTLET TO ENCLOSURE.88 [7.] NEMA TYPE MAINTAINED. [58.9] 6.5 [58.8] Standard Features Ball-bearing Motors CFC-Free Refrigerant EMI/RFI Suppressor Low Temperature Control Thermostat NEMA Rating Maintained (UL50) UL/CUL Listed Gray Powder Finish Accessories and Options Adapter Plate for rack mounting Compressor Heater Condensate Evaporator Cooling Effect Detector Filter Recoating Adhesive Filters for replacement Internal corrosion protection Lifting Eyes Low Ambient Kit and Compressor Heater Mounting Hinge Short Cycle Protector Special materials or finishes Special motors, line cords, or connectors Stainless or Aluminum Cabinet Weather Protection Kit MICRO-MINI SERIES AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WAC0MML6 000 600 5/50 5/00 60/50.5 WAC0MML6 000 600 5/50 0/00 60/50. WACMML6 00 70 5/50 5/00 60/50.5 WACMML6 00 70 5/50 0/00 60/50. 6 NEW PRODUCT IN 00 MOUNTING PLAN.75 [69.9].6 [6.]. [.7] ().8 [5.5] DIA. HOLES (). [8.0] DIA. HOLES. [58.8].6 [6.]. [.7] 0.5 [6.] 0.8 [0.6].75 [69.9] 0.8 [0.6] 9.8 [9.].5 [8.6].88 [.8].00 [0.6].00 [0.8].88 [7.].88 [.8].00 [0.6]. [09.5].88 [7.].50 [.]. [.7] DIA..5 [8.6] 7.9 [0.6].50 [8.] 6.6 [58.8] 0.68 [7.] 0.6 [5.9]. [58.8].5 [6.6].50 [8.].50 [8.] DIA. POWER CORD HOLE.50 [.] 8.00 [0.].00 [5.].00 [5.] OPTIONAL POWER CORD EXIT CONDENSATE DRAIN Dimensions, inches [metric], are for reference only and subject to change.
K8 INTEGRITY SERIES NEMA/X AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS NEMA TYPE /X MAINTAINED Description Designed specifically for NEMA and X Enclosure applications that require washdown or are subject to outdoor storm conditions, Integrity NEMA /X Air Conditioners protect the ratings of NEMA or X Enclosures. These exclusive patented UL/CUL Recognized Panel-Mounted Air Conditioners provide superior closedloop cooling and also protect against the hazards specified for both Indoor and Outdoor NEMA and X Enclosures. Tested and rated by universally recognized Underwriters Laboratories, these uniquely-designed 0-B Stainless Steel Air Conditioners prevent unwanted environmental penetration of NEMA and X Enclosures as they provide a clean, cool internal environment. With the design advantages of the Integrity NEMA /X Series and the inclusion of the unique Mounting Template and Assembly Bracket (M/TAB), modified for this design, this series offers the finest in cooling innovation and technology. Features Capacities range from,000 to 0,000 BTU/H in ", 8", 7" and 59" heights UL/CUL Listed or Recognized Tested and approved by UL for NEMA and X Enclosures CFC-free Refrigerant Gasketed flanges on all four mounting edges for positive leakproof seal Exclusive modified integral Mounting Template and Assembly Bracket (M/TAB) for quick, easy installation. Thermostatic Low Temperature Control prevents over-cooling and provides energy-efficient operation Internal Corrosion Protection EMI/RFI Suppressor minimizes transient line spikes during on/off cycling Separate blower-driven evaporator and condenser air systems penetrate high static pressure applications Rugged heavy duty stainless steel exterior
INTEGRITY SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS K9. [.] NEMA TYPE /X MAINTAINED FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE COOL AIR OUTLET TO ENCLOSURE M/TAB.5 [89.].50 [68.].00 [0.].50 [800.] THERMOSTAT ADJUSTMENT ACCESS Standard Features CFC-Free Refrigerant EMI/RFI Suppressor Internal corrosion protection Low Temperature Control Thermostat M/TAB Mounting System NEMA /X Rating Maintained (UL50) Stainless Steel Cabinet UL/CUL Recognized Accessories and Options Cooling Effect Detector Filter Recoating Adhesive Filters for replacement Lifting Eyes Low Ambient Kit & Compressor Heater Short Cycle Protector Special materials or finishes Cooling Capacity (BTU/H) PERFORMANCE CHART KNACPR WNACPR 8000 7000 6000 Maximum enclosure air temperature ºF 5000 000 000 5 0 000 0 00 000 0 75 90 80 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded areas not recommended. INTEGRITY SERIES AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WNACPR6 000 5 5/50 5/00 60/50.0/.0 05 WNACPR6 000 5 0/50 0/00 60/50 6.0 05 WNACPR6 000 650 5/50 5/00 60/50.0/.0 05 WNACPR6 000 650 0/50 0/00 60/50 6.0 05 6 NEW PRODUCT IN 00 MOUNTING PLAN.5 [.7].00 [0.6].5 [07.9] UNIT.50 [68.] ().50 [6.] DIA. HOLES.50 [800.].5 [.7].6 [7.].00 [50.8] M/TAB & CUTOUTS 5. [0.0].00 [0.] 0.50 [66.7] 8.00 [0.] (6). [8.0] DIA. HOLES 8.00 [0.].8 [55.].8 [55.]. [79.].00 [0.6] POWER CORD 6.00 [660.] 5.00 [7.0] 0.9 [766.8].06 [.7].5 [89.].50 [68.]. [.].00 [5.].00 [0.6].5 [08.0].7 [.8] 0.7 [9.].75 [9.] 0.7 [9.] UNIT OUTLINE.50 [88.9].50 [9.].50 [8.].8 [96.8] ().0 [5.0] DIA. HOLES M/TAB OUTLINE.88 [7.] 0.88 [.] 0.8 [0.6] M/TAB.75 [9.].8 0.8 [5.] [9.7] UNIT MUST BE " (00mm) MINIMUM ABOVE FLOOR FOR FILTER ACCESS Dimensions, inches [metric], are for reference only and subject to change. UL/CUL Recognized models are available as Listed at added cost.
K0 INTEGRITY 8 & 7 SERIES AIR-COOLED SIDE-MOUNTED AIR CONDITIONERS NEMA TYPE /X MAINTAINED M/TAB A 8.56 [7.] FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) 7.06 [.] 8.00 [57.] K THERMOSTAT ADJUSTMENT WARM AIR RETURN FROM ENCLOSURE COOL AIR OUTLET TO ENCLOSURE PERFORMANCE CHARTS KNAC7P R WNAC7P8R 500 000 Maximum enclosure air temperature ºF 0500 9000 7500 5 0 6000 0 500 000 500 75 00 90 80 70 80 90 00 0 0 0 Ambient Temperature (ºF) KNAC0P R WNAC0P7R 6000 000 Maximum enclosure air temperature ºF 000 0000 8000 5 6000 0 0 000 00 000 90 80 0 75 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded areas not recommended. Cooling Capacity (BTU/H) Cooling Capacity (BTU/H) INTEGRITY SERIES 8 & 7 AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WNAC6P8R6 6000 550 /50 5/00 60/50 0 80 WNAC6P8R6 6000 550 /50 0/00 60/50 9./9.9 80 WNAC7P8R6 7000 6000 /50 5/00 60/50 0 80 WNAC7P8R6 7000 6000 /50 0/00 60/50 9./9.9 80 WNAC8P7R6 8000 6500 /50 0/00 60/50 0.9/.5 05 WNAC0P7R6 0000 7750 /50 0/00 60/50 0.9/.5 05 DIMENSIONS INCHES (METRIC) MODEL A B C D E SERIES 8 7.75 (958.8) 6.69 (9.9).75 (.8).75 (.8) 8. (6.5) SERIES 7 7.00 (9.8) 5.9 (66.6).5 (.).5 (85.7) 7.7 (695.) MODEL F G H J K SERIES 8.50 (6.5). (0.) 6.00 (5.) 7.00 (685.8) 7.00 (99.8) SERIES 7.50 (6.5).00 (0.6) 8.00 (0.).00 (88.) 6.5 (7.7) 6 NEW PRODUCT IN 00 UNIT MOUNTING PLAN M/TAB & CUTOUTS.5 [.7] 8.56 [7.] ( J ).50 [6.] DIA. HOLES.75 [.] (H). [7.9] DIA. HOLES 5.00 [8.] 8.56 [7.]. [.7] 9. [6.5] 8.8 [.8].8 [.5].00 [0.6] C 9.75 [7.6] 7. [88.9] 5 (J).50 DIA. HOLES G B A.87 [7.8].8 [80.7] D.8 [07.8]. [5.] E F B 5.5 [87.] 6.69 [69.9] A K G.50 [8.].50 [8.] 5.8 [.5] 7.75 [50.8] 0.68 [7.] UNIT OUTLINE 9.87 5.56 [50.6] [.] M/TAB OUTLINE 0.69 [7.5].50 [8.] 5.9 [.8] 6.88 [8.6].6 [69.9] 0.8 [0.6] M/TAB 8. [60.].50 [8.] 7.75 [50.9] APPROXIMATE WEIGHT (LBS.) Series 8 80 Series 7 05 UNIT MUST BE " (00mm) MINIMUM ABOVE FLOOR FOR FILTER ACCESS DRAIN 7. [5.0] Dimensions, inches [metric], are for reference only and subject to change. UL/CUL Recognized models are available as Listed at added cost.
WDTS SERIES 000 BTU NEMA X SIDE-MOUNTED AIR CONDITIONER K0A WDTS0005NX Industry Standards UR, cur, and CE recognized NEMA,, X Applications Designed for side mounting on any enclosure surface where hot spot cooling or low capacity cooling is required Meets NEMA,, X protection against water and corrosive material Closed loop cooling ensures clean enclosure air is recirculated without ever mixing the contaminated ambient air Clean stainless steel design Features Ra refrigerant Thermostat control (must remove cover) Expansion valve permits increased efficiency through improved evaporator heat transfer and less frequent compressor operation Built in condensate evaporator Continuous air circulation from high capacity fans EMI/RFI suppression meets CE requirements 8' line cord with plug on 5V versions. 8' line cord with no plug on 0V versions Aluminum filter provided with easy access for cleaning Gasket, mounting kit, and template for enclosure cutout and drilling are included Exterior case easily removable for field service Q Mount allows unit to hang in place for easy installation Accessories Replacement Filters Operation Notes In extremely humid environments, condensation may accumulate and is drained-off through the overflow outlet. A hose may be attached to the mm outlet to drain the water in a controlled manner cooling capacity Q 0 (BTU) (Watt) cabinet air temperature T i 0 000 600 750 75 500 WDTS 000 +5ºC/ºF +5ºC/95ºF 86 50 +5ºC/77ºF 0 5 5 5 55 T u (ºC) 68 77 95 (ºF) ambient air temperature
K0B WDTS SERIES 000 BTU NEMA X SIDE-MOUNTED AIR CONDITIONER WDTS 000 SERIES NEMA X SIDE MOUNT AIR CONDITIONER CATALOG RATED CAPACITY RATED RANGE OF POWER RUNNING STARTING 8' LINE NUMBER (BTU/H) VOLTAGE WATTS OPERATION CONSUMPTION AMPS CURRENT CORD WDTS0005NX 000 5V 60Hz 0V 50Hz 580 0-7V 70W.9A.8A w/plug WDTS0000NX 000 0V 50/60 Hz 580 98-5V 0W.A 7.A w/out plug EMI/RFI Suppression: According to CE Type of Refrigerant: Ra Refrigerant Charge: 00g Adjustable Thermostat: Factory set at +95º F (+5º C) Max. Ambient Air Temp.: +5º F (+5º C) Min. Ambient Air Temp.: +6º F (+8º C) Air Capacity Circulation: 0 CFM Internal, 0 CFM External (unrestricted) Condensate Discharge: Filter Mat: Db Noise Level: Unit Weight: Exterior Housing: Condensate evaporator 50 g/m 6 db (A) 7 lbs. (.7kg) 0 stainless steel *Special order product. Consult factory for lead time. 0.57" (.5) 5.6" ().6" (86) 8.90" (.6) 8.5" (6.5).87" (7).68" (9) 7.5" (90.5)." (5) 0." Ø 8(6x) 7.5" (5) 9.0" (9.6).6" (95.) 7.5" (90.5) 5.6" (.8).07" (0.) 6.5" (Ø 65.) 5.6" () " (5.)
COMPACT SERIES AIR COOLED TOP-MOUNT AIR CONDITIONERS K THERMOSTAT ADJUSTMENT POWER CORD 7.00 [.8] FILTERED CONDENSER AIR INLET (Ambient Air In) CONDENSER OUTLET (Warm Ambient Air Out) WARM AIR RETURN FROM ENCLOSURE 0.5 [60.] COOL AIR OUTLET TO ENCLOSURE FILTER 0.00 [508.0] DRAIN Standard Features Built-in Condensate Evaporator CFC-Free Refrigerant EMI/RFI Suppressor Low Temperature Control Thermostat UL/CUL Listed Gray Powder Finish Accessories and Options Cooling Effect Detector Enclosure Heater Filter Recoating Adhesive Filters for replacement Internal corrosion protection Lifting Eyes Low Airflow Detector Low Ambient Kit Short Cycle Protector Special materials or finishes Special motors, linecords or protectors Stainless or Aluminum Cabinet KACHTL WACHTL 6000 550 Maximum enclosure air temperature ºF 500 750 000 50 5 0 500 750 0 75 0 00 80 70 80 90 00 0 0 0 Ambient Temperature (ºF) Operation within shaded areas not recommended. Cooling Capacity (BTU/H) PERFORMANCE CHART COMPACT SERIES AIR-COOLED TOP-MOUNTED AIR CONDITIONERS MODEL RATED CAPACITY 95/95 RATING AMBIENT TEMP. F VOLTS HZ RUNNING APPROX. (BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.) WACHTL6 000 00 5/50 5/00 60/50. 85 WACHTL6 000 00 5/50 0/00 60/50 5.9 85 WACHTL6 000 00 5/50 5/00 60/50. 85 WACHTL6 000 00 5/50 0/00 60/50 5.9 85 6 NEW PRODUCT IN 00.50 [6.5] 0.75 [9.] MOUNTING PLAN 7.00 [.8] 5.50 [9.7].50 [.9].75 [.5] 8.00 [0.].6 [0.7].9 [55.6] 0.5 [60.] 0.00 [508.0] 0.50 [66.7] ().5 [6.] WELD NUTS 7.75 [96.9] 5.75.00 [6.] [0.6] 0.00 [508.0].75 [.5] 5.00 [7.0].50 [8.] 7.00 [.8].50 [.] POWER CORD 0.50 [.7] POWER CORD 5' [.5] CONDENSATE DRAIN TUBE.50 [.].50 [.].00 [50.8].75 [.5].00 [50.8].50 [.]
K VORTEX COOLERS Industry Standards UL Listed NEMA, or X NEMA /X NEMA UL File E576 Applications Compressed air cooling is used where conventional enclosure cooling (air conditioners or heat exchangers) is not possible. Example: Small to medium size enclosures; nonmetallic enclosures; areas where the size of cooling devices is restricted. Features Suitable for harsh environments Small physical size Creates cool air without refrigerants (no CFC s, HFC s) Exceptionally reliable no moving parts Virtually no maintenance Requirements Clean, dry, oil-free compressed air (00 PSIG/70ºF or below) required to achieve published BTU/hr. ratings. Lower pressures and higher temperatures will reduce BTU/hr. ratings A 5 micron water and particulate removal filter must be installed prior to operating any Vortex Cooler (included in kits) An oil removable filter can be installed between the 5 micon filter and the Vortex cooler if oil is present in the compressed air line Mounting holes: NEMA kits () -/" (8mm) or /" knockout hole for cooling tube and () /6" hole for thermostat NEMA & NEMA X kits () -5/6" (9mm) or -/" knockout hole for cooling tube and () #8 holes for thermostat Kit Includes the Following Vortex Cooling Tube Solenoid Valve 0V 60Hz 0V 50 Hz (0V available) 5 micron water and particulate removal filter Ducting Kit Thermostat How Enclosure Coolers Create Cold Air Vortex Coolers are powered by a vortex tube a unique device that creates a vortex from compressed air and separates it into hot and cold airstreams. Here s how it works. The vortex tube s cylindrical generator causes the input compressed air to rotate, reaching speeds up to,000,000 rpm as it is forced down the inner walls of the hot, or longer end of the vortex tube. At the end of the hot tube, as small portion of this air exits through a needle valve as hot air exhaust. The remaining air is forced back through the center of the incoming air stream at a slower speed. The heat in the slower moving air is transferred to the faster moving incoming air. This super-cooled air flows through the center of the generator and exits through the cold air exhaust port. Compressed Air In Control Value Cold Air Out Vortex Generation Chamber Hot Air Out
VORTEX COOLERS K VORTEX COOLERS CAPACITY AIR CONSUMPTION TUBE CATALOG THERMOSTAT SURFACE THERMOSTAT NEMA UL COOLING TUBE NUMBER BTUH KCAL/H SCFM SLPM (FACTORY SET) TEMP AT BTU MOUNTING TYPE TYPE MATERIAL W75000 00 0 8 7 90 F ± 50 F External Aluminum W70900 900 5 5 5 90 F ± 50 F External Aluminum W790500 500 78 5 708 90 F ± 50 F External Aluminum W797700 700 5 5 708 90 F ± 50 F Internal Aluminum W797SS700 700 5 5 708 90 F ± 50 F Internal X X Stainless Steel ACCESSORIES CATALOG NUMBER W8OILFILTER WOILFILTER FILTER TYPE AND SIZE Auto-drain oil removal filter, /8" NPT (F), rated to 5 SCFM/708 SLPM Auto-drain oil removal filter, /" NPT (F), rated to 50 SCFM/5 SLPM Model W75000 Model W70900 & W790500 Model W797700 & W797SS700 Note: Thermostats for Models W75000, W70900 and W790500 mounts in an /6" (8mm) diameter hole.
K WPFB/WPFBE FILTERED BOX FANS & GRILLES Applications Used for enclosure cooling in low static pressure applications. Features High airflow with low noise operation makes these versatile cooling fans very popular in a wide range of applications Reliable cooling is achieved particularly in areas with minimum space requirements The cooling system incorporates the filtered fan boxes as its air inlet, while the exhaust grille is the air outlet The washable aluminum filter grille and air filter is easily accessible and can be removed for cleaning Available in 5 VAC or 0 VAC 50/60 Hz versions Heavy gauge steel construction Attractive, ascetically appealing grille design All models can pressurize or exhaust Aluminum filter is coated with adhesive baffle surfaces for dust and dirt collection. Can be recoated after cleaning for optimum performance Note: One grille and filter are included with each fan package. Normally, an additional exhaust grille and filter required for each installation and must be ordered separately. Accessories Exhaust Grille and Filters (see page L) Filter Coat PERFORMANCE GRAPHS STATIC PRESSURE.0.5 WPFB00 WPFB00 WPFB500 KP0 KP60 Fan: Unit: 60 Hz. 50 Hz. 60 Hz. 50 Hz. STATIC PRESSURE.0.5 Fan: Unit: 60 Hz. 50 Hz. 60 Hz. 50 Hz. STATIC PRESSURE.50.5 KP00 Fan: Unit: 60 Hz. 50 Hz. 60 Hz. 50 Hz..0 0 0 50 00 50 00 AIRFLOW C.F.M.. 0 5 75 50 5 00 AIRFLOW C.F.M..05 0 0 50 00 50 600 AIRFLOW C.F.M. Static pressure is in inches of water.
WPFB/WPFBE SERIES FILTERED BOX FANS & GRILLES K5 WPFB Box Fan WPFBE Exhaust Grille with Filter Filter Coat Industry Standards UR, cur, and CE recognized WPFB SERIES BOX FANS CATALOG FREE-FLOW AIR RATED NOMINAL RUNNING WATTS A B C D E F G H NUMBER DELIVERY (CFM) VOLTAGE (RPM) AMPS WPFB005 05 5 000 0.8 5 WPFB000 05 0 000 0.8 5 WPFB005 0 5 00 0.9 WPFB000 0 0 00 0.9 WPFB5005 560 5 600 0.87 60 WPFB5000 560 0 600 0.87 60 6. 7.8.8 5.6 6.8. 0.75 7.00 (56) (88) (6) () (6) (05) (9) (78) 6. 7.8.8 5.6 6.8. 0.75 7.00 (56) (88) (6) () (6) (05) (9) (78) 7.6 8.88.00 7. 7.88.50. 8.50 (9) (6) (76) (8) (00) () () (6) 7.6 8.88.00 7. 7.88.50. 8.50 (9) (6) (76) (8) (00) () () (6).6.00.56..88 6.88..50 (95) (0) (6) (8) (0) (75) (5) (8).6.00.56..88 6.88..50 (95) (0) (6) (8) (0) (75) (5) (8) WPFBE SERIES EXHAUST GRILLES WITH FILTERS CATALOG NUMBER WITH FILTER FILTER ONLY WPFBE00 WPFBE00 WPFBE500 WPFBM00 WPFBM00 WPFBM500 A B D E F G W* 6. 7.8 5.6 6.8. 0.75 5.66 (56) (88) () (6) (05) (9) () 7.6 8.88 7. 7.88.50. 7.6 (9) (6) (8) (00) () () (8).6.00..88 6.88..6 (95) (0) (8) (0) (75) (5) (8) FILTER COAT CATALOG NUMBER DESCRIPTION WAX0 0 oz pump spray bottle C D H E 0.9 DIA PLACES D F F D G A 0.6 D G AIR FLOW E B
K6 MUFFIN FANS & FINGER GUARDS WAAXFN WAGARD6 MUFFIN FANS & FINGER GUARDS Applications Designed for use in enclosures where space is limited and reliable cooling is required. Features Fan furnished standard with " lead wire. 90 degree plug attached Black color Impeller and frame are glass reinforced thermoplastic, UL9-VO Die cast aluminum housing Finger guards are welded electroplated nickel chrome steel wire. Guards withstand 00 lbs. separation force to meet UL, CSA standards One finger guard and all mounting hardware is provided. Additional finger guards can be mounted on either side for maximum safety WAXFN SERIES MUFFIN FANS & WAGARD SERIES FINGER GUARDS CATALOG NUMBER RATED RATED VOLTAGE FREQ NOISE MAXIMUM AIR FLOW MAXIMUM DIMENSIONS FAN INPUT SPEED STATIC FAN RATING (Hz) LEVEL H X W X D GUARD (WATTS) (RPM) (M/MIN) CFM PRESSURE/H0 WAAXFN WAGARD 5 7/5 50/60 500/000 7 ±.5/. 88/0 5.8/7.0.7x.7x.50 (0x0x8) WAAXFN WAGARD 0 7/5 50/60 500/000 7 ±.5/. 88/0 5.8/7.0.7x.7x.50 (0x0x8) WA6AXFN WAGARD6 5 6/5 50/60 800/500 6 ± 5./6.6 90/5 5./6.6 6.77x6.77x.0 (7x7x5) WA6AXFN WAGARD6 0 6/5 50/60 800/500 6 ± 5./6.6 90/5 5./6.6 6.77x6.77x.0 (7x7x5) WA0AXFN WAGARD0 5 5 50/60 650 55 57 0 0.00x0.00x.50 (5x5x89) WA0AXFN WAGARD0 0 50/60 650 55 57 0 0.00x0.00x.50 (5x5x89)
WAVK, WAVK-SS & WAFLT LOUVER PLATE KITS & FILTER KITS K7 WAVK00SSA WAFLT LOUVER PLATE KITS Description Designed to provide ventilation or cooling in enclosures where excessive moisture or excessive internal heat is a problem. These kits are fabricated from gauge steel and include all hardware for mounting. Kits are easily field installed by making a cutout of the proper size and attaching the louver plate in place. Finish is ANSI 6 gray polyester powder finish over phosphatized surfaces or 6 stainless steel. Filter kit must be ordered separately. FILTER KITS FOR LOUVER PLATES KITS Description Designed for use with Louver Plate Kit. Mounting holes on filter brackets align with mounting holes on louver kits. Aluminum filters are good for stopping dust and dirt from penetrating the enclosures. Filters are designed to mount behind louver kits. Kit consists of aluminum filter, brackets and all necessary hardware for installation. Louver kit must be ordered separately. WAVK SERIES LOUVER PLATE KIT AND WAFLT SERIES FILTER KITS FOR LOUVER PLATES CATALOG NUMBER NUMBER NUMBER LOUVER KIT LOUVER KIT OF OF LOUVER FILTER KIT PAINTED 6 S.S. LOUVERS ROWS WAVK00 WAVK00SSA6 WAVK00 WAVK00SSA6 WAFLT WAVK00 WAVK00SSA6 WAFLT WAVK00 WAVK00SSA6 WAFLT WAVK060 WAVK060SSA6 WAFLT6 WAVK0606 WAVK0606SSA6 WAFLT66 6 WAVK0806 WAVK0806SSA6 WAFLT86 WAVK0808 WAVK0808SSA6 WAFLT88 6 WAVK08 WAVK08SSA6 WAFLT8 LOUVER LENGTH A B L M P R S.00.5.5.00.00.50.50 (5) (8) (8) (5) (5) (6) (6).00.87.50.6.5..75 (76) (98) () (67) (8) (79) (95).00.75.50.50.5.00.75 (76) () () (89) (8) (0) (95).00 5.6 5.50.7.5.87.75 (0) () (0) () (08) () () 6.00 5.6 7.50.7 6.5.87 6.75 (5) () (9) () (59) () (7) 6.00 7.87 7.50 6.6 6.5 7. 6.75.56 (5) (00) (9) (68) (59) (8) (7) (90).00 8.8 9.50 6.9 8.5 7. 8.75.7 (0) (08) () (76) (0) (89) () (9).00 0.56 9.50 9. 8.5 9.8 8.75.90 (0) (68) () (6) (0) (9) () ().00 9. 9.50.06 8.5.56 8.75 7.8 (0) (6) () (57) (0) (70) () (85) 6 NEW PRODUCT IN 00 Note: Center holes (dimension S ) are not needed on any filter kits. Only 6 x 6 and larger louver kits require center holes.
K8 WAVK, WAVK-SS & WAFLT LOUVER PLATE KITS & FILTER KITS Notes: Installation Instructions. Make sure the proper louver kit and/or filter kit has been ordered.. Locate and mark holes and cutout as shown in figure.. Drill holes using a 7/" drill bit making sure there are no electrical wires or internal components in the way.. Assemble louver kits and/or filter kits as shown in figure. Note: After installation is complete, make sure louver and filter kits do not interfere with any internal or external equipment.
EHG SERIES ENCLOSURE RADIANT HEATERS K9 EHG00 Industry Standards UL Recognized Component cul Recognized Component CE Recognized Applications Designed to provide enclosed electronic, pneumatic, hydraulic, and mechanical equipment with protection from low temperatures, condensation, and corrosion. Features Positive Temperature Coefficient heater unit maintains a stable temperature environment within enclosures, allowing critical components to perform with consistent reliability for longer periods Expanded voltage range of 0V to 0V Heating body is extruded, black anodized, aluminum Easily installed by clip mounting on 5mm DIN rails Connection: Push-type terminals Protection Class: (tested for grounding at,600v) CAUTION Do not mount on wooden structures. Avoid placement near heat-sensitive components Accessories Thermostats (see pages K-K) EHG SERIES ENCLOSURE RADIANT HEATERS CATALOG RATED DIMENSIONS WATTS* Hz NUMBER VOLTAGE H X W X D EHG05 5 0-50 50/60.60x.80x.00 (65x70x50) EHG00 0 0-50 50/60.60x.80x.00 (65x70x50) EHG05 5 0-50 50/60.60x.80x.00 (65x70x50) EHG060 60 0-50 50/60 5.50x.80x.00 (0x70x50) EHG075 75 0-50 50/60 5.50x.80x.00 (0x70x50) EHG00 00 0-50 50/60 5.50x.80x.00 (0x70x50) EHG50 50 0-50 50/60 8.70x.80x.00 (0x70x50) *Due to the nature of PTC heaters, the actual power rating of the heater can be up to 0% lower, or 5% higher than the nominal power rating at 68ºF (0ºC) ambient temperature.
K0 WHVL SERIES ENCLOSURE FAN HEATERS WHVLO000 Industry Standards UL Recognized Component cul Recognized Component CE Recognized Applications Used when larger heating capacities or internal forced air circulation is required and space is limited. Features Compact design to prevent condensation or maintain minimum temperature in enclosures Cartridge heater heating element 0,000 hour life expectancy at 68ºF ambient Connection: 5 pole terminal for max. AWG Easily installed by clip mounting on 5mm DIN rails Protection class (tested for grounding at,50 V) Heater comes fully assembled with fan CAUTION Do not mount on wooden structures. Avoid placement near heat-sensitive components. Note that fan must be used in conjunction with heating element Accessories Thermostats (see pages K-K) WHVL SERIES ENCLOSURE FAN HEATERS OPERATING MAXIMUM CATALOG RATED DIMENSIONS WATTS CURRENT TEMPERATURE NUMBER VOLTAGE H X W X D (AMPS) WITH FAN WHVLO000 0 00 0.89 50ºF (0ºC).85x.5x.(7x80x) WHVLO500 0 50.0 0ºF (60ºC).85x.5x.(7x80X) WHVLO000 0 00.79 50ºF (0ºC).85x.68x5.9(7x9x5) WHVLO000 0 00.6 0ºF (60ºC).85x.68x5.9(7x9x5) WHVLO000 0 00.5 60ºF (80ºC).85x.68x5.9(7x9x5) 00 & 50W Heaters 00, 00 & 00W Heaters
WCR SERIES FAN HEATERS K WCR07500 Industry Standards UL Recognized Component cul Recognized Component CE Recognized Applications Designed to protect sensitive mechanical, electrical, and electronic equipment from the harmful effects of condensation, corrosion, and low temperatures. Thermostatically controlled fan-driven heater units maintain a stable temperature with enclosure so critical components can perform more reliably over a longer period of time. Features Positive Temperature Coefficient (PTC) semiconductor heating element, self regulating and temperature limiting Adjustable thermostat LED lamp for optical indication of function Durable, non-metallic plastic housing, UL9-VO Connection: - pole terminal, max. AWG Easily installed by clip-mounting on 5mm DIN rail CAUTION Do not mount on wooden structures. Avoid placement near heat-sensitive components WCR SERIES FAN HEATERS CATALOG RATED MAX. AMPS THERMOSTAT AXIAL FAN TEMPERATURE DIMENSIONS WATTS NUMBER VOLTAGE (INRUSH CURRENT) ADJUSTABLE FROM BALL BEARING SCALE H X W X D WCR07500 0 550 8.5A -0ºF (0-60ºC) 0 CFM Fahrenheit 6.50x.9x5.00 (65x00x8) WCR07500 0 00 7.5A -0ºF (0-60ºC) 0 CFM Celsius 6.50x.9x5.00 (65x00x8) WCR075500 0 650.0A -0ºF (0-60ºC) 6 CFM Fahrenheit 6.50x.9x5.00 (65x00x8) WCR075500 0 550.0A -0ºF (0-60ºC) 6 CFM Celsius 6.50x.9x5.00 (65x00x8) For spacing, add " clearance for heat sensitive parts
K EGL SERIES FAN HEATERS EGL50-0 Industry Standards UL Recognized Component cul Recognized Component CE Recognized Applications Use when larger heating capacities or internal forced air circulation is required. Designed to prevent condensation or maintain minimum temperature in enclosures. Features Heating element is micanite with fail safe thermostat Black, anodized aluminum extruded body Ball bearing life expectancy is 0,000 hrs. at 70ºF (0ºC) Connection: pole terminal for AWG 8 Easily installed by clip mounting on 5mm DIN rails CAUTION Do not mount on wooden structures. Avoid placement near heat-sensitive components Accessories Thermostats (see pages K-K) EGL SERIES FAN HEATERS CATALOG RATED STARTING SURFACE CIRCULATION DIMENSIONS WATTS AXIAL FAN NUMBER VOLTAGE AMPS TEMPERATURE POWER H X W X D EGL50-0 0 50. 67ºF Ball Bearing 0 CFM Free Blowing 7.00x.5x.5 (78x80x80) EGL50 0 50. 67ºF Ball Bearing 0 CFM Free Blowing 7.00x.5x.5 (78x80x80) EGL00-0 0 00.5 67ºF Ball Bearing 0 CFM Free Blowing 9.76x.5x.5 (5x80x80) EGL00 0 00.7 67ºF Ball Bearing 0 CFM Free Blowing 9.76x.5x.5 (5x80x80) For spacing, add " clearance for heat sensitive parts
ETR SERIES THERMOSTATS K ETR0 ETR0F Industry Standards UL Recognized Component cul Recognized Component CE Recognized CSA Rated Applications Designed to provide air temperature control and monitoring in switch gear enclosures that are set up to operate with heaters, fans, filter ventilators, heat exchangers, and/or signal transmitters. When the enclosure reaches the pre-determined set point, temperature contacts in the thermostat are activated and the fan or heater automatically begins to operate. Thermostats prolong the life expectancy of heaters and fans by curtailing their operating hours and also increase the working efficiency of electrical components by exposing them to fewer contaminants from the surrounding environment. Features Normally Closed Thermostat For the control of fan heaters and heaters Normally Open Thermostat For the control of cooling units, fans, filter ventilators or switching, or signal transmitters in the event of overheating Available in Fahrenheit or Celsius scale Thermostatic bi-metallic sensor element Easily installed by clip mounting on 5mm or 8mm DIN rails ETR SERIES THERMOSTATS CATALOG TEMP. TEMP. SWITCHING FOR PRODUCT DIMENSIONS NUMBER SCALE RANGE TYPE H X W X D ETR0F Fahrenheit -0ºF ETR0 Celsius 0-60ºC ETR0F Fahrenheit -0ºF ETR0 Celsius 0-60ºC Normally Closed Normally Closed Normally Open Normally Open Housing made from gray flame retardant UL9-VO plastic Connection: pole terminal for max. AWG Switching Difference (hysteresis): ºF (7ºC) Switching Capacity: 5 A () AC 0V, 0 A () AC 50V, 0A V DC, 5A V DC Heating Heating Cooling Cooling.0x.0x.0 (60xx5).0x.0x.0 (60xx5).0x.0x.0 (60xx5).0x.0x.0 (60xx5)
K ETF SERIES THERMOSTATS ETF000 Industry Standards UL Recognized Component cul Recognized Component CE recognized Applications Designed to provide both air temperature and humidity control as well as monitoring in electrical and electronic enclosures. Highly effective in ATM s, parking control gates, ticket dispensers and traffic control systems where equipment is exposed to wide range of outdoor elements. Features Independently senses the relative humidity and temperature. Resistive and inductive loads (heaters or Filterfans ) can be switched 00,000 cycle life expectancy LED lamp for optical indication of function Durable, non metallic plastic gray housing, UL9-VO Easily installed by clip mounting on 5mm DIN rail Switching capacity: 8A() AC 0V, 0.8A DC 8V, 8A DC V ETF SERIES FAN HEATERS SWITCHING RESPONSE CATALOG OPERATING TEMPERATURE TEMPERATURE RELATIVE DIMENSIONS DIFFERENCE TIME NUMBER VOLTAGE SCALE RANGE HUMIDITY RANGE H X W X D (HYSTERESIS) (SECONDS) ETF0000F 0 Fahrenheit Approx..6ºF (ºK) Approx. 60-0ºF 50 to 90%.6x.97x.5 (67x50x9) ETF000 0 Celsius Approx..6ºF (ºK) Approx. 60 0-60ºC 50 to 90%.6x.97x.5 (67x50x9)
STFX SERIES UNIVERSAL THERMOSTAT MOUNT K5 STFX05 Applications Effective substitute for DIN rail or Unistrut. Multipurpose mounting devise which allow the mounting of small DIN rail mountable appliances reducing time and labor. Features Provides direct snap-in mounting for thermostats, time relays, small heaters, terminals, and other appliances with DIN rail mounting or by the use of screw holes Manufactured from black UL9-VO polyamide material Included self adhesive bears continuous loads of. lbs. (after hours) Holes for screw mounting are provided for heavy applications STFX SERIES UNIVERSAL THERMOSTAT MOUNT CATALOG HOLDING PACKAGE TEMP. RANGE OF DIMENSIONS NUMBER CAPACITY QUANTITY* MOUNTING MATERIAL H X W X D STFX05. lbs. (00g) initially --ºF.50x.70x.55. lbs. (500g) after 5 (-0-55ºC) (8xx) hour curing period *Sold in package quantity only
K6 WAFMP SERIES FAN MOUNTING PLATE WAFMP Fan Mounting Plate Description Designed to mount a fan and louver kit together. This fan mounting plate kit consists of a fan mounting plate, filter and all necessary hardware for installation. When ordering a fan mounting plate, you will need to order a fan, louver kit and a fan guard. Fans, louver kits and fan guards must be ordered separately. WAFMP SERIES FAN MOUNTING PLATE CATALOG NUMBER FAN, FILTER & LOUVER LOUVER KIT FAN FAN* MOUNTING PLATE KIT PAINTED** GUARD *** WAFMP WAAXFN WAVK0606 WAGARD WAFMP WAAXFN WAVK0606 WAGARD WAFMP6 WA6AXFN WAVK0808 WAGARD6 WAFMP6 WA6AXFN WAVK0808 WAGARD6 WAFMP0 WA0AXFN WAVK0809 WAGARD0 WAFMP0 WA0AXFN WAVK0809 WAGARD0 *See page K6 for information on fans. **See page K7 for information on louver kits. ***See page K6 for information on guards. Notes: Installation Instructions:. Make sure that the proper kits have been ordered.. Locate and mark holes and cutout per louver kit instructions on page K7-K8.. Assemble kits as shown in figure.. After installation is complete, make sure that no hardware interferes with any internal or external equipment.
800 SERIES - FILTER FANS/EXHAUST FILTER & MATS K7 SERIES 80 SERIES 800, 80, 80 Industry standards IP5 IP55 (with fine filter mat) Application The latest passive technology for fan cooling and pressurizing of industrial enclosures Filtered passive ventilation can be provided by an exhaust filter for either convection cooling or in combination with a fan in forced air cooling Features All four models are available in 0 and 0 volt with an expected service life of 50,000 hours Self-adhesive seal on mounting frame prevents dust and water from entering the enclosure The functional design of the intake exhaust fan hoods minimize direct infiltration of falling water By simply turning the axial fan, the direction of the airflow can be changed by 80 degrees Air Channeling makes the filter fan particularly quiet in operation Plastic self-extinguishing UL9-V0 and temperature resistant F to 58F Durable, reusable medium filter mat included RAL705 Light Gray Finish Ball Bearing Axial Fan with plastic impeller UL9V-0. lead wires long (pressure clamps inclusive) Time-Saving Steps 800 Series Fans can be easily connected and installed from the outside of the cabinet.. Remove protective film from the sealing strips provided on the mounting frame. Insert mounting frame into enclosure cutout.. Terminate the axial fan with push type connectors and slide the unit into the mounting frame.. Insert the Filter Mat and snap on the protective Hood. Time-Saving Assembly and Maintenance
K8 800 SERIES - FILTER FANS/EXHAUST FILTER & MATS." 5." 5.".6"." 6.".0"." 8."." (8mm).6" (68mm).8" (5mm).8" 5.".9" 6.7" 6.9" 8.9" 9.8" (50mm) 800 SERIES FILTER FAN Catalog No. (for 0V 60Hz) W08000- W0800-5 W0800-7 W0800-0 Catalog No. (for 0V 50Hz) W08000- W0800-5 W0800-7 W0800-0 Filter mat: Medium grade 50 g/m, filtering degree 8%, Particle < 0 µm, G(EN779) Air volume free blowing: cfm ( m /h) 9 cfm (55 m /h) 60 cfm (0 m /h) 76 cfm (00 m /h) with exhaust filter: 9 cfm (6 m /h) cfm ( m /h) 0 cfm (68 m /h) 5 cfm (0 m /h) Current consumption 0V 60 ma 80 ma 80 ma 00 ma 0V 80 ma 00 ma 00 ma 700 ma Power consumption 0V W 5W 5W 60W 0V W 5W 5W 60W Average noise level at ft DIN EN ISO 96- db (A) 0 db (A) 9 db (A) 5 db (A) Mounting depth.8" (5 mm)." (58 mm)." (86 mm).6" (65 mm) Enclosure cut-out.8" x.8" (97 x 97mm +0.).9" x.9" (5 x 5mm +0.) 6.9" x 6.9" (76 x 76mm +0.) 9.8" x 9.8" (50 x 50mm) Weight. lbs (0.5 kg). lbs (.0 kg). lbs (.9 kg) 7.7 lbs (.5 kg) 0V / 60Hz models have increased air volume performance of approx. 5% 800 SERIES EXHAUST GRILLE & FILTER Catalog No. W800F- W80F-5 W80F-7 W80F-0 Filter mat: Medium grade 50 g/m, filtering degree 8%, Particle Ø to 0 µm, G (DIN 85) Mounting depth 0.6" (6 mm) 0.6" (6 mm) 0.6" (6 mm) 9" ( mm) Enclosure cut-out.8" x.8" (97 x 97mm +0.).9" x.9" (5 x 5mm +0.) 6.9" x 6.9" (76 x 76mm +0.) 9.8" x 9.8" (50 x 50mm +.) Weight 0.6 lbs (0.7 kg) 0.8 lbs (0.8 kg). lbs (0.60 kg). lbs (95 kg) REPLACEMENT FILTER MATS Medium filter (G) MM08600- MM0860-5 MM0860-7 MM08608-0 Fine filter (F5) FM0860- FM0860-5 FM08605-7 FM08609-0 MOUNTING FRAME HOLE CENTERS FOR ATTACHING WITH SCREWS - HOLE Ø /8 (MM) X =." (09 mm) X = 5." (7 mm) X = 7." (88 mm) X = 0." (6 mm) X X
WPF SERIES FILTERFANS K9 WPF0-5BK Industry Standards UR, cur, and CE recognized IP (IP5 with optional WPFG Series gasket) Applications Most innovative technology for fan cooling and pressurizing of industrial enclosures Provides a high quality, economical method of cooling enclosures Filtered passive ventilation can be provided by an exhaust filter for either convection cooling or in combination with a fan in forced air cooling Slim line design allows grille to protrude from enclosure surface less than one quarter inch Maintains aesthetics of enclosure Features All models are 5V with an expected service life of 0,000 hours High performance fan motors and finger guards Polycarbonate fire retardant plastic grilles, UL9-VO Durable, reusable filter mat included Grilles are available in black or beige Patented Click and Fit system allows for rapid filter fan and exhaust filter installation without screws; this time saving feature will cut installation time by up to 0 minutes from traditional box fan packages Cutout template provided with every unit Fan or exhaust filter simply snaps into cutout opening Connector type: WPF0 Series, " wires. WPF0 WPF60 Series terminal strip Accessories Exhaust Filters Gaskets (WPFG Series) recommended if installing on enclosure with textured finish (only WPF0) Replacement Filters -0/+ mm -0/+ mm WPF0 WPF0-0/+ mm -0/+ mm WPF5 WPF0 WPF50 WPF60
K0 WPF SERIES FILTERFANS WPF SERIES FILTERFANS CATALOG NUMBER BLACK GRILLE BEIGE GRILLE FREE FLOW AIR MAX. AMBIENT FILTER SOUND RATED AIR DELIVERY STATIC TEMP. FILTERING REQUIRED CUT OUT DENSITY LEVEL VOLTAGE DELIVERY W/EXHAUST PRESSURE DEGREE F LEVEL DIMENSION (G/M) (DB) (CFM)* (CFM) (PA) MAX/MIN WPF0-5BK WPF0-5 5V 6. 0. 9.00 0/ 50.00 67% 9.6x.6 (9x9) WPF0-5BK WPF0-5 5V 7.95 8. 69.00 / 50.00 8% 9.9x.9 (5x5) WPF5-5BK WPF5-5 5V 88.67 6.9 57.00 / 50.00 8% 55 8.78x8.78 (x) WPF0-5BK WPF0-5 5V 68.59. 89.00 / 50.00 8% 55 8.78x8.78 (x) WPF50-5BK WPF50-5 5V. 6.90 05.00 / 50.00 8% 69.6x.6 (9x9) WPF60-5BK WPF60-5 5V.09 0.6 5.00 / 50.00 8% 7.6x.6 (9x9) *Add 5% for operation @ 60Hz WPF0 Air Flow WPF0 Air Flow WPF5 Air Flow WPF0 Air Flow WPF50 Air Flow WPF60 Air Flow
WPFA SERIES EXHAUST GRILLE WITH FILTER K WPFA0BK WPFA0 Industry Standards IP (IP5 with optional WPFG Series gasket) Applications Polycarbonate fire retardant plastic grilles, UL9-VO Durable, reusable filter mat included Grilles are available in black or beige Accessories Gaskets (WPFG series) recommended if installing on enclosure with textured finish EXHAUST GRILLE WITH FILTER CATALOG NUMBER FILTER FILTERING REQUIRED CUT OUT BLACK GRILLE BEIGE GRILLE DENSITY (G/M) LEVEL DIMENSIONS WPFA0BK WPFA0 50 67%.60x.60/9x9 WPFA0BK WPFA0 50 8%.90x.90/5x5 WPFA5/0BK WPFA5/0 50 8% 8.80x8.80/x WPFA50/60BK WPFA50/60 50 8%.50x.50/9x9 WPFA 0 WPFA 0 WPFA 5/0 WPFA 50/60
K FILTERFAN REPLACEMENT ACCESSORIES WPFG5/0 WPFM0 WPGBK WPG5/0BE GASKETS FOR FILTERFANS Applications Packaged individually Provides added sealing protection Recommended when fans or exhaust grilles are installed on enclosures with textured finishes Changes Filer Fan rating from IP to IP 5 when installed WPFG SERIES GASKET FOR FILTERFANS CATALOG NUMBER GASKET USE WITH FILTER FAN NO. USE WITH EXHAUST GRILL NO. WPFG0 WPFG0 WPFG5/0 WPFG50/60 WPF0-5BK WPF0-5 WPF0-5BK WPF0-5 WPF5-5BK WPF0-5BK WPF5-5 WPF0-5 WPF50-5BK WPF60-5BK WPF50-5 WPF60-5 WPFA0BK WPFA0 WPFA0BK WPFA0 WPFA5BK WPFA0BK WPFA5 WPFA0 WPFA50BK WPFA60BK WPFA50 WPFA60 AC & FILTERFAN REPLACEMENT FILTER MATS Applications Replacement filter mat for WPF-5 Series Filterfans and WPFA Series Exhaust Grilles. Features Packaged in quantities of 5 Made of synthetic fibers Re-usable up to 0 times 00% resistant to humidity AC & FILTERFAN REPLACEMENT FILTER MATS FILTER USE WITH USE WITH MASS FILTER CATALOG FILTER FAN EXHAUST FILTER DENSITY H W NUMBER OR A/C SERIES GRILLE LEVEL % (G/M) WPFM0 WPF0-5 WPFA0 67 50.0 (85).0 (85) WPFM0 WPF0-5 WPFA0 8 50.50 (5).50 (5) WPFM5/0 WPFM50/60 WPF5-5 WPF0-5 WPF50-5 WPF60-5 WPFA0 8 50 8.0 (0) 8.0 (0) WPFA50 8 50.00 (80).00 (80) WPFM5/0AC WDTS00-6000 8 50 8.0 (0) 8. (0) WPFM50/60AC WDTS8000-000 8 50.00 (80).00 (80) WPFMDTTAC WDTT500-500 8 50.8 (00).8 (00) FILTERFAN REPLACEMENT GRILLES Features Packaged individually Grille only replacement for filter fans Available in black or beige FILTERFAN REPLACEMENT GRILLES CATALOG NUMBER BLACK BEIGE BLACK GRILLE BEIGE GRILLE BLACK BEIGE USE WITH GRILLE GRILLE FOR EXHAUST FOR EXHAUST GRILLE GRILLE A/C UNIT GRILLE FOR FILTER FOR FILTER GRILLE GRILLE FAN FAN W/FILTER W/FILTER WPGBK WPGBE WPF0-5BK WPF0-5 WPFA0BK WPFA0 WPGBK WPGBE WPF0-5BK WPF0-5 WPFA0BK WPFA0 WPGBK WPGBE WDTS00-6000 WPG5BK WPG5BE WDTS6000-000 WPF5-5BK WPF5-5 WPFFA5BK WPFA5 WPF0-5BK WPF0-5 WPFA0BK WPFA0 WPF50-5BK WPF50-5 WPFA50BK WPFA50 WPF60-5BK WPF60-5 WPFA60BK WPFA60