Exova Warringtonfire Holmesfield Road Warrington WA1 2DS United Kingdom T : +44 (0 1925 655116 F : +44 (0) 1925 655419 E : warrington@exova.com W: www.exova.com Ad-hoc IEC 60331-2 x Ad-hoc investigation to determine the fire performance of a cable junction box, using the principles of IEC 60331-2 A Report To: CE-TEK Controls & Enclosure Technik Ltd Date: 17 th November 2015 Issue No.: 1 Page 1 Document Reference: 358061 Registered Office: Exova (UK) Ltd, Lochend Industrial Estate, Newbridge, Midlothian EH28 8PL United Kingdom. Reg No.SC 70429 This report in issued in accordance with our terms and conditions, a copy of which is available on request.
Executive Summary Objective To determine the performance of a cable junction box using the principles of IEC 60331-2: 2009. Generic Description Product reference Thickness Density A glass reinforced polyester (GRP) cable junction box CEP121290FRF Confidential Not stated Individual components used to manufacture composite: Terminals 0.5/10FR Terminal Not stated Not stated Fuse 6 Amp FR Fuse Not stated Not stated Please see pages 5 & 6 of this test report for the full description of the product tested Test Sponsor Test Results: CE-TEK Controls & Enclosure Technik Ltd, Units 1-4 Tideswell Business Park, Tideswell, Derbyshire, SK17 8NY, UK. When tested using the general principles of IEC 60331-2: 2009, with exposure to fire alone at a temperature of at least 830 C for a duration of 3 hours, the cable junction box maintained its integrity for the duration of the test. Date of Test 10 th November 2015 Signatories Responsible Officer C. Meachin * Technical Officer * For and on behalf of Exova Warringtonfire. Authorised S. Deeming * Business Unit Head Report Issued: 17 th November 2015 This version of the report has been produced from a.pdf format electronic file that has been provided by Exova Warringtonfire to the sponsor of the report and must only be reproduced in full. Extracts or abridgements of reports must not be published without permission of Exova Warringtonfire. Document No.: 358061 Page No.: 2 of 10
CONTENTS PAGE NO. EXECUTIVE SUMMARY... 2 SIGNATORIES... 2 TEST DETAILS... 4 DESCRIPTION OF TEST SPECIMENS... 6 TEST RESULTS... 8 APPENDIX 1 PHOTOGRAPHS OF TEST SPECIMENS... 9 REVISION HISTORY... 10 Document No.: 358061 Page No.: 3 of 10
Test Details Introduction The sponsor, CE-TEK Controls & Enclosure Technik Ltd, approached Exova Warringtonfire and requested that a series of tests be conducted to demonstrate that their cable junction box complies with the requirements of IEC 60331-2: 2009 when exposed to fire alone. In order to demonstrate that the cable junction box meets the requirements of the standard, it was used in conjunction with standard fire resisting cables whilst they were exposed to the test conditions given in IEC 60331-2: 2009. Purpose of test To determine the performance of a specimen of a cable junction box when it is subjected to the conditions of test specified in IEC 60331-2: 2009 when exposed to fire alone. The purpose of the test method is to determine whether a cable can maintain circuit integrity when it is exposed to the fire conditions described within the method. The test was performed using the general principles of the procedures specified in IEC 60331-2: 2009 and this report should be read in conjunction with this standard. Scope of test IEC 60331-2: 2009 specifies a test procedure and gives a performance requirement, including recommended flame application times, for cables of rated voltage up to and including 600/1000 V, and with an overall diameter not exceeding 20mm. It is intended to cover low voltage power cables and control cables with a rated voltage which are required to maintain circuit integrity when subject to fire and mechanical shock under specified conditions at a temperature of at least 830 C. BS EN 50200: 2006 specifies a test method for cables intended for use as emergency circuits for alarm, lighting and communication purposes. It is applicable to cables whose rated voltage does not exceed 600/1000V and overall diameter does not exceed 20mm. Deviation from test standard Fire test study group/egolf IEC 60331-2: 2009 specifies a test method for cables intended for use as low voltage power cables and control cables with a rated voltage which are required to maintain circuit integrity when subject to fire and mechanical shock under specified conditions at a temperature of at least 830 C. In this case the sponsor of the test requested that the application of mechanical shock be omitted from test and that their cable junction box be exposed to fire alone for the duration of the test. Certain aspects of some fire test specifications are open to different interpretations. The Fire Test Study Group and EGOLF have identified a number of such areas and have agreed Resolutions which define common agreement of interpretations between fire test laboratories which are members of the Groups. Where such Resolutions are applicable to this test they have been followed. Document No.: 358061 Page No.: 4 of 10
Instruction to test Provision of test specimens The test was conducted on the 10 th November 2015 at the request of CE-TEK Controls & Enclosure Technik Ltd, the sponsor of the test. The specimens were supplied by the sponsor of the test. Exova Warringtonfire was not involved in any selection or sampling procedure. Conditioning specimens Burner verification procedure of The specimens were received on the 22 nd October 2015. Prior to the test the specimens were conditioned for at least 16 hours in an atmosphere having a temperature of 23 ± 2 C and a relative humidity of 50 ± 5%. The verification procedure for the burner was conducted in accordance with Annex A of IEC 60331-2: 2009 at the start of the test day. Temperature measurements recorded by each thermocouple were logged using an Omega HH1384 four channel thermometer and datalogger at 1 second intervals over a period of 10 minutes and then averaged. This determined the gas & air flow rates and the position of the burner that were used for the subsequent cable test. The gas and air flows were provided through the use of M&W Instruments mass flow controllers, model numbers D-6341-DR and D-6361-DR. Form in which the specimens were tested The cable junction box was mounted to a nominally 10mm thick calcium silicate backing board and used the standard cable supplied and described below. Document No.: 358061 Page No.: 5 of 10
Description of Test Specimens The description of the specimens given below has been prepared from information provided by the sponsor of the test. All values quoted are nominal, unless tolerances are given. General description A glass reinforced polyester (GRP) cable junction box Product reference CEP121290FRF Name of manufacturer CE-TEK Controls & Enclosure Technik Ltd Thickness See Note 1 below Colour reference See Note 1 below Flame retardant details See Note 2 below Product reference 0.5/10FR Terminals Terminals Detailed description / 0.5mm 2-10mm 2 capacity fire rated terminals composition details Name of manufacturer CE-TEK Product reference 6 Amp FR Fuse Fuse Detailed description / 6 Amp fire rated fuse assembly composition details Name of manufacturer CE-TEK Brief description of manufacturing process The junction boxes are manufactured from high impact resistance glass reinforced polyester (GRP) complete with sealed cover with high temperature low smoke halogen free gasket rated to IP67. The junction box was fitted to a calcium silicate backing board using stainless steel screws General description Enhanced FR cable Product reference Prysmian FP Plus Name of manufacturer Prysmian Diameter 9.4mm (stated by sponsor) 9.4mm (determined by Exova Warringtonfire) Weight per unit length 123kg/km (stated by sponsor) 123kg/km (determined by Exova Warringtonfire) Cable marking PRYSMIAN 2015H LPCB 077g/02 FP PLUS LSOH BS7629-1 EN50200 PH120 BS8434-2 120MIN BS5839-1 ENHANCED Cable function Power feed Colour Red Number of cores x core size 3 x 2.5mm 2 Voltage rating 300/500v Cable configuration Outer sheath Aluminium screen tape Conductor insulation Conductors Earth wire Junction box Continued on next page Document No.: 358061 Page No.: 6 of 10
Photograph of cable The sponsor was unable to provide any further information regarding the cable Brief description of manufacturing process See Note 3 below Note 1: The sponsor of the test has provided this information but at the specific request of the sponsor, these details have been omitted from the report and are instead held on the confidential file relating to this investigation. Note 2: The sponsor was unwilling to provide this information. Note 3: The sponsor was unable to provide this information. Document No.: 358061 Page No.: 7 of 10
Test Results Applicability of test result The test results relate only to the behaviour of the specimen of the cable junction box under the particular conditions of test; they are not intended to be the sole criterion for assessing the potential fire hazards of the product in use. The test results relate only to the specimen of the cable junction box in the form in which it was tested. Small differences in the composition of the product may significantly affect the performance during the test and may therefore invalidate the test results. Care should be taken to ensure that any product, which is supplied or used, is fully represented by the specimen, which was tested. Results of test Validity When tested using the general principles of IEC 60331-2: 2009, with exposure to fire alone at a temperature of at least 830 C for a duration of 3 hours, the cable junction box maintained its integrity for the duration of the test. The specification and interpretation of fire test methods are the subject of ongoing development and refinement. Changes in associated legislation may also occur. For these reasons it is recommended that the relevance of test reports over five years old should be considered by the user. The laboratory that issued the report will be able to offer, on behalf of the legal owner, a review of the procedures adopted for a particular test to ensure that they are consistent with current practices, and if required may endorse the test report. This report may only be reproduced in full. Extracts or abridgements shall not be published without permission of Exova Warringtonfire. Document No.: 358061 Page No.: 8 of 10
Appendix 1 Photographs of test specimens Before test After test After test inside box Document No.: 358061 Page No.: 9 of 10
Revision History Issue No : Revised By: Reason for Revision: Issue Date: Approved By: Issue No : Revised By: Reason for Revision: Issue Date: Approved By: Document No.: 358061 Page No.: 10 of 10