INSTALLATION MANUAL Seda 8 Widespread 2-Handle Faucet FUS-1823 www.kraususa.com I toll free: 1.800.775.0703 I 2014-2015 Kraus USA Inc. I REV. August 6, 2015
Thank you for purchasing Kraus We would like to take this opportunity to thank you for your business with Kraus USA. It is our sincere hope that you are completely satisfied with your experience. We welcome any questions or comments you may have, and will be glad to assist you in the future. For more information about Kraus products, please visit our website at: www.kraususa.com Please register your new Kraus product at the following web address in order to activate the warranty and receive the full benefit of customer support: www.kraususa.com/registration Sincerely, Kraus Customer Service Department 2
Prior to Installation: Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber s putty, or silicone Place bucket under angle stops. Turn on angle stops to flush any debris prior to installing new plumbing. Shut off angle stops Max countertop thickness: 1 3/8 Tools you will need: Adjustable Wrench Phillips Screwdriver Safety Goggles Bucket 3
FUS-1823 Diagram and Parts List B D 7A A 7A I J 8A 8B 8C 8D K 8A C1 8B 8C 8D E1 E2 C1 C2 C3 C2 C3 F H G A. Hot Handle Valve B. Cold Handle Valve C. Hot & Cold Handle Mounting Hardware: C1. Rubber & Metal Washer C2. Mounting Nut C3. Mounting Screws D. Spout E. Spout Mounting Hardware: E1. Rubber & Metal U-Washer E2. Mounting Nut F. T-Union G. Hot & Cold Waterlines H. 3/8 in. OD x 1/2 in. IPS Waterlines I. Aerator J. Aerator Key K. Hex Wrench 4
Pop up Drain Diagram and Parts List a Ø54 2 1/2 Ø34mm 1 11/32 b c 30~50 1 3/16 1 31/32 23mm 29/32 d e 192mm 7 9/16 M38 x 1.5 180mm 7 3/32 f h g Ø32 1 1/4 a. Drain Body b. Rubber Washer c. Concave Washer d. Plastic Washer e. Mounting Nut f. Tailpipe Washer g. Tailpipe h. Connector 5
Faucet Dimensions 4.92 125mm 4.92 125mm 2.87 73mm 1.8 46mm 2.24 57mm 1.8 46mm 5.62 143mm 4.96 126mm 4.76 121mm MAX 1.18 30mm 1 2 9/16-18UNEF Step 1: Remove mounting hardware and T-union 1 1/4-18UNF-2A A 7A 8A 8B 8C 8D D 7A 8A B 1 1/16 ~ 1 5/8 27mm ~ 41.3mm Remove D T-union (F) and mounting hardware (E) from spout (D). 8A 8B Remove mounting 8C hardware (C) 8D from hot and cold handle valves (A & B) 7A A 6 C E F 8B 8C 8D C E1 E2 F C1 C2 C3
2 3 1 1/4-18UNF-2A 9/16-18UNEF 9/16-18UNEF Step 2: Install & secure spout D B 8A 8B 8C 8D 8A 8B 8C C 8D B 1 1/16 ~ 1 5/8 27mm ~ 41.3mm 7A 1 1/16 ~ 1 5/8 27mm ~ 41.3mm 7A Install spout (D) through hole in countertop or sink. Attach rubber & metal U-washer (E1) A and mounting nut (E2). Adjust spout (D) to proper position and tighten mounting nut (E2) with adjustable wrench. Secure C1T-union (F) onto supply line of C2spout (D). Tighten T-union (F) C3 with adjustable wrench E1 E2 F 3 1 1/4-18UNF-2A 9/16-18UNEF A B C1 H C2 C3 1 1/16 ~ 1 5/8 27mm ~ 41.3mm Step 3: Install & secure hot and cold handle valves Install hot and cold handle valves 5 B (A & B) through hole in countertop or sink. Attach rubber & metal washer (C1) and mounting nut (C2) to the threaded mounting pipe. From underneath the countertop or sink, tighten mounting nut (C2) onto valves (A I & B) with adjustable wrench until J mounting nut (C2) by snug. Secure tightening mounting screws (C3) with a Phillips head screwdriver H 5 7
Step 4: 4 Connect waterlines to faucet and main valve 5 A H G F G H B H Secure hot & cold waterlines (G) to hot and cold valves (A & B) (Hand- Tighten Only). Thread other end of waterlines to T-union (F). Attach 3/8 in. OD x 1/2 in. IPS waterlines (H) to copper pipe on valves A. Hot Side: Left B. Cold Side: Right Secure other end of waterlines to angle stops. Tighten all ends with adjustable wrench until snug. Turn on angle stops and check for leaks (DO NOT TURN FAUCET ON) I J Step 5: Install Drain a b c d e f h g Remove connector (h), tail pipe (g), mounting nut (e), plastic washer (d), and concave washer (c) from drain body (a) b c d e a 8
Step5: Install drain c d e f h g b c d e a b c d e b a a Install drain body (a), with rubber washer (b) attached, into the drain hole. From underneath, attach concave washer (c) (narrow end up), plastic washer (d), and mounting nut (e) to drain body (a) c d e Tighten mounting nut (e) with adjustable wrench until snug. Thread connector (h), with tailpipe (g) attached, onto drain body (a) and hand-tighten e f g h Installer Tip: Make g sure tailpipe washer (f) is installed in tailpipe Connect tailpipe (g) to p-trap g 9
Step 6: Flush faucet Remove adjustable aerator (I) with aerator key (J). Turn water on for 1 minute to remove any debris. Reassemble aerator (I) and adjust to desired position I J 10
Replacement Part List - FVS-1823 1 4 3 10 18 2 5 6 12 11 13 14 15 16 17 7 8 9 19 1. Hot Handle 2. Cold Handle 3. Set Screw 4. Cover Button 5. Hot Cartridge 6. Hot Valve 7. Rubber & Metal Washer 8. Mounting Nut 9. Mounting Screw 10. Adjustable Aerator 11. Rubber & Metal U Washer 12. Mounting Nut 13. T-Union 14. Cold Cartridge 15. Cold Valve 16. Hot & Cold Waterlines 17. 3/8 in. OD x 1/2 in. IPS Waterlines 18. Aerator Key 19. Hex Wrench 11
Replacement Part List - Pop Up Drain 1 2 3 4 5 6 7 8 9 10 11 1. Drain Cap 2. Seal 3. Spring 4. Drain Body 5. Rubber Washer 6. Concave Washer 7. Plastic Washer 8. Mounting Nut 9. Tailpipe Washer 10. Tailpipe 11. Connector 12
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION 1 Leakage under the handle 9 10 Hot or cold cartridge (5 or 14) may be loose 11 12 13 Hexagon Nut Remove cover button (4). Loosen set screw (3) with hex wrench (19). Remove handle (1 or 2). Tighten hot or cold cartridge (5 or 14) with adjustable wrench 3 Aerator drips or has inconsistent water flow pattern Aerator (10) may be dirty or not seated properly Unscrew aerator (10) with aerator key (18). Remove aerator (10) and clean out debris Hot Water Cold Water Water will not shut off completely Hot or cold cartridge (5 or 14) may need to be adjusted or replaced Remove cover button (4). Loosen set screw (3) with hex wrench (19). Remove handle (1 or 2). Remove hot or cold cartridge (5 or 14) with adjustable wrench. Check for cracks 11 12 13 Drain is leaking Close 25 Open Care & Maintenance Washers 90 may be compromised or installed incorrectly Left Hot Water *To keep the product clean & shining, follow the steps below: Check washers to make sure they are installed Push correctly and not cracked 1. Rinse with clean water & dry with a soft cloth 2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners 3. Do not use cloth with a coarse surface 4. Unscrew the aerator and clean when necessary *This installation manual is subject to change without further notice. 13
Codes/Standards Applicable: NSF/ANSI 372 GREEN LEAD FREE I APMOR&T TM NSF/ANSI 61 ASME A112.18.1M 1.5GPM 5.7L/min maximum Water Efficiency KRAUS LIMITED LIFETIME WARRANTY This product has been manufactured and tested to the highest quality standards by Kraus USA Inc. ( Kraus ). We offer our customers thoughtfully crafted fixtures & accessories, engineered for enduring performance over years of use. WHO IS COVERED BY THE WARRANTY This warranty extends to the original purchaser only. This warranty is not transferable, between homes or owners and is only applicable to residential use. WHAT IS COVERED BY THE WARRANTY Kraus warranties this product against defects due to material or craftsmanship error during the warranty period: Kraus will provide replacement parts at no charge, or at its option, replace any product or part of the product that is deemed defective, under normal installation, use, service and maintenance. If Kraus is unable to provide a replacement and repair is not practical or cannot be made in timely fashion, Kraus may elect to refund the purchase price in exchange for the return of the product. CONDITIONS AND EXCLUSIONS Like other home fixtures, Kraus products will require light maintenance to ensure proper function. We provide you with complete knowledge to perform this maintenance and can also recommend resources if you are unable to fulfill this service. A. Kraus will not be responsible for product failures due to lack of maintenance or proper use. Please read your care and maintenance documentation to determine the limits of proper use. B. The original sales receipt, order number, and/or proof of purchase must be presented at the time of the warranty claim, without exception, for this warranty to be applied to all Kraus products. C. Kraus recommends installing all Kraus products with a licensed, professional plumber. Kraus will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to use a licensed professional. Please read your care and maintenance documentation to determine the limits of proper use. D. Commercial use will automatically void this warranty. E. This warranty is not applicable to Kraus products purchased from an unauthorized seller. For a complete list of authorized sellers please visit http://www.kraususa.com/ where-to-buy.html 14
NON-APPLICABILITY OF THIS WARRANTY By the purchase and use of our products, you agree that Kraus is not liable for incidental, consequential or special damages associated with the return, replacement, installation or use of your product. This includes freight costs, cartridge replacement, labor, travel time, lost profit, home damages and other contingent liabilities and costs (including, without limitation, costs associated with experts, investigations, analyses, attorneys and other professionals and services). The Kraus warranty is a comprehensive and explicit limit of liability, and all items outside of it are not addressable by or the responsibility of Kraus. Certain states have variances regarding implied warranties and in those situations we remain fully compliant. KRAUS USA Inc. makes no implication that products comply with any or all local building or plumbing codes. It is the consumer s responsibility to determine local code compliance. This warranty extends to the original purchaser and first consumer. HELP LINE Our customer service hours are Monday Friday, 9am 8pm EST. Be sure to visit our website at www.kraususa.com If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com If you are an Authorized Partner please contact a Partner Support Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8954 Partnersupport@kraususa.com In requesting warranty service, please be ready to provide: 1. Proof of purchase. 2. A description of the problem. 15
www.kraususa.com