Sealed Type Liquid Line and Suction Line Specifications

CATALOG 0 Page,, 4a, 404A, 407C, 40A, 0, 07 Also Compatible with Refrigerants, 4,, 40A & B, 40A & B, 408A, 409A The universal acceptance of the Catch-All Filter-Drier is due to its unique molded porous core, consisting of a blend of highly effective desiccants. The quality features built into it assure years of service on any refrigeration system. MOISTURE The Catch-All Filter-Drier removes moisture from the refrigerant by adsorbing and retaining it deep within the desiccant granules. The blend of desiccants used in the Catch-All Filter-Drier are specially formulated for exceptional water removal. FOREIGN MATTER The Catch-All Filter-Drier will filter out scale, solder particles, carbon, sludge, dirt or any other foreign matter with negligible pressure drop. Fine particles that would go through an ordinary strainer are removed down to a minimum size in one pass filtration. The large filtering area of the Catch-All Filter-Drier core permits it to collect a large amount of dirt without plug up. ACID The Catch-All Filter-Drier is unexcelled in acid removal ability. The hydrochloric, hydrofluoric, and various organic acids are adsorbed and held by the desiccant in a manner similar to the adsorption of moisture. Tests have demonstrated that the Catch-All Filter- Drier has superior acid removal ability when compared to competitive driers. This ability, along with its excellent ability to clean up the oil, is responsible for the excellent field performance in cleaning up severely contaminated systems. OIL SLUDGE AND VARNISH Even the best refrigeration oils break down to produce varnish, sludge and organic acids. Only the Catch-All Filter-Drier is capable of removing these products of oil decomposition. SPECIAL APPLICATIONS A special HH core Catch-All Filter-Drier is available to remove wax which frequently causes difficulty on low temperature refrigeration systems. For cap tube systems, use the C-0-CAP or C-0-CAP-T Catch-All which has fittings suitable for attaching to any size capillary tube. Remember...It s the CORE that counts! Sealed Type Liquid Line and Suction Line Specifications C LISTED US C SERIES LIQUID LINE SUCTION LINE CONNECTION SIZE VOLUME of OVERALL LENGTH SOLDER DESICCANT SOCKET DEPTH SAE FLARE ODF SOLDER ODF SOLDER Cubic SAE FLARE ODF SOLDER C-0 C-0-S /4 4.9.8 0.8 C-0-CAP C-0-CAP-T Extended /4 Male.8 C-0-F /4 Male - Inlet /4 Female - Outlet.8 C-0-FM /4 Female - Inlet /4 Male - Outlet.8 C-0 C-0-S /8 4.69.88 C-0 C-0-S C-0-S /4 /6 4.7 4.9 4.8 0.8 C-0-F /4 Male - Inlet /4 Female - Outlet 4.9 C-0-FM /4 Male - Inlet /4 Female - Outlet 4.9 C-0 C-0-S /8.9 4. C-08 C-08-S /4.6. 0.8 C-08-S /6 C-08 C-08-S C-08-S-T-HH /8 9. 6.06. C-084 C-084-S C-084-S-T-HH 6..44 0.0 C-6 C-6 C-64 C-6 C-6-S C-6-S C-6-S C-64-S C-6-S C-67-S C-0 C-0-S C-04 C-04-S C-0 C-0-S C-06-S C-07-S C-09-S C-4 C-44 C-44-S C-4 C-4-S C-47-S C-49-S C-607-S C-609-S COMPACT STYLE C-64-S-T-HH C-6-S-T-HH C-66-S-T-HH C-67-S-T-HH C-0-S-T-HH C-06-S-T-HH C-07-S-T-HH C-09-S-T-HH C-47-S-T-HH C-49-S-T-HH C-47-S-T-HH C-49-S-T-HH C-4-S-T-HH C-4-S-T-HH C-607-S-T-HH C-609-S-T-HH C-44-S-TT-HH C-4-S-TT-HH C-46-S-TT-HH C-47-S-TT-HH C-49-S-TT-HH /4 /6 /8 /8 /8 /8 /8 /8 -/8 -/8 /8 6 0 4 6. 6.7 6.94 7. 9.69 9.88 0.9 9.6 9.94 0. 48 60 4.7.94.88 6.00 6. 6.7 6.9 8.88 9.00 9. 9.6 9.80 9.7 9.0 9. 9.8 9.7 0.4 0.74 0.94 0.94 0.8 0.0 0.6 0.6 0.7 0.0 0.6 0.6 0.7 0.0 0.6 0.7 0.7 0.94.00.06 DIAMETER of BODY UL and UL C Listed Guide SMGT-File No. SA-76A & B. Maximum Rated Pressure of 60 psi, except for the C-40 Series rated at 40 psi and the C-40 Series rated at 00 psi. For complete information see your Sporlan Wholesaler, our website at www.sporlan.com, or write Sporlan and request Bulletin 40-0. 6.00 6.00 4.4 4.8 4.8 4.97 4.9 0.7 0.0 0.66 0.66 0.7.7.44.6.00.00.0 4.7.00 4.44

Page 6 CATALOG 0,, 4a, 404A, 407C, 40A, 0, 07 Also Compatible with Refrigerants, 4,, 40A & B, 40A & B, 408A, 409A Replaceable Core Type ODF Solder Connections The rugged construction of the Replaceable Core Catch-All has proven itself in the field for many years. The design features include:. The famous molded porous core for maximum contaminant removal. The core cannot swell, powder or pack assuring ease of installation and removal.. The bolt and nut attachment of the end plate provides simple trouble-free installation.. The internal construction gives a one piece assembly and assures proper core alignment. 4. A complete line of fitting sizes all with copper fittings.. No plastic parts are used all internal parts are plated steel. 6. A corrosion resistant powder paint protects the exterior of the shell. C LISTED US RCW-48 RC-4864 RCW-00 C-969-G Specifications C-R44-G C-R4-G C-R47-G C-48-G C-487-G C-489-G C-48-G C-48-G C-967-G C-969-G C-96-G C-96-G C-449-G C-44-G C-44-G C-9-G C-9-G C-97-G C-00-G C-007-G C-4007-G C-400-G C-400-G C-4009-G C-400-G C-484-PG C-966-PG C-448-PG C-9-PG CONNECTIONS ODF SOLDER /8 /8 -/8 -/8 -/8 -/8 -/8 -/8 -/8 -/8 -/8 -/8 -/8 -/8 -/8 -/8 -/8 4-/8 - OPTIONAL SECONDARY FILTER* NUMBER of CORES or FILTER ELEMENTS CORE PART NUMBER VOLUME of DESICCANT Cubic FILTER ELEMENT PART NUMBER MOUNTING BRACKETS RCW-4 4 A-7- FS-480 C-4006-PG 4 48 RPE-48-BD A-68 FS-960 RCW-48, RC-4864 or RC-4864-HH 96 RPE-48-BD A-68 FS-440 44 RPE-48-BD A-68 FS-900 4 9 RPE-48-BD A-68 00 RPE-00 A-7-4 RCW-00, RC-0098 or RC-0098-HH 400 RPE-00 A-7-4 NPT PIPE CONNECTIONS RCW-48, RC-4864 or RC-4864-HH RCW-00, RC-0098 or RC-0098-HH 48 96 44 9 RPE-48-BD A-68 OVERALL LENGTH 9.00 9.06 9.44 9. 9.0 9.0 9.60 9.60 4.84.04.4.4 0.8 0.68 0.68 6. 6. 6. 7.94 8.06 4.6 4.7 4.44 4.8. 9.08 4.67 0.4.8 400 RPE-00 A-7-4.44 UL and UL C Listed Guide SMGT-File No. SA-76A & B. C-480 through C-90 Series shells have a 60 psig rating for R-40A. C-0000 and C40000 shells have a 00 psig rating. *Optional Secondary Filter must be purchased separately. O-rings (p/n 6-0) are supplied with each secondary filter, but can be purchased separately. The secondary filter cannot be used if the shell is installed in the suction line. Type numbers with G suffix indicate that unit is supplied with /4 female pipe connection in the end plate and pipe plug. For liquid line service and angle charging valve for system charging purposes can be installed in place of the pipe plug. Angle charging and Schrader type access valves are available from your Sporlan Wholesaler. Type numbers with P suffix indicates female threaded pipe connections. Note: Do not use RPE-48-BD and RPE-00 filter elements in ammonia systems. For complete information see your Sporlan Wholesaler, our website at www.sporlan.com, or write Sporlan and request Bulletin 40-0.

CATALOG 0 Page 7, 4a, 404A, 407C, 40A, 07 Liquid Line Ratings and Selection Recommendations C-0 C-0-CAP C-0-S C-0-F C-0-FM ESURFACE FILTERING AREA Square R- 60 PPM WRATINGS AT ARI STANDARD CONDITIONS WATER CAPACITY DROPS R-4a R-404A & 07 R-07C R-40A QREFRIGERANT FLOW CAPACITY Tons at psi P 7 F F 7 F F 7 F F 7 F F 7 F F 4a & 404A 07 SEALED 9 6 0 67 48 7 8 7 7 0 407C 40A & 4a...0..4 C-0.....4 C-0-S.8..6..7 C-0 C-0-S C-0-F C-0-FM..9.4.9.0 46 9 8 4 69 8 40 6 48 C-0-S.4.... C-0 4..8.7.8 4.0 C-0-S 4.7 4.. 4. 4. C-08 C-08-S..9.4.9.0 C-08-S.7..4.. C-08 40 96 6 88 79 7 0 6 04 78 4. 4..0 4. 4.4 C-08-S. 4.7.4 4.7.0 C-084 8.7 7.9.9 8.0 8. C-084-S 9.6 8.8 6.4 8.8 9.4 C-6 C-6-S..9.4.9.0 C-6-S.7..4.. C-6 4. 4..0 4. 4.4 C-6-S 46 97 96 8 44 4 07 00 8 9. 4.7.4 4.7.0 C-64 0. 9. 6.8 9. 9.8 C-64-S.0 0. 7. 0. 0.7 C-6.8.6 9..7.4 C-6-S.9 4. 0.6 4.6. C-0 4.6 4..0 4. 4.4 C-0-S. 4.7.4 4.7.0 C-04 0. 9. 6.8 9. 9.8 C-04-S 696 67 76 4 809 68 86 89 0 7.0 0. 7. 0. 0.7 C-0 4.9.6 9.9.7 4. C-0-S 6.9... 6.4 C-07-S.6 9.8 4.4 9.9.0 C-44. 0. 7.6 0.. C-44-S.4.4 8..4. C-4.8 4. 0.6 4.6.4 67 96 7 07 7 088 88 788 4 407 0 C-4-S 7. 6..8 6. 7. C-47-S. 0. 4.8 0.4. C-49-S 4.. 6..4.7 C-607-S 9. 6.6 9. 6.8 8.4 06 9 4 090 68 6 7 78 604 44 C-609-S. 0.4. 0.7.4 SELECTION RECOMMENDATIONS (Tons) REFRIGERATION AIR CONDITIONING COMMERCIAL & FIELD LOW TEMPERATURE REPLACEMENT EQUIPMENT or FIELD BUILT UP SYSTEMS 404A, 0 &07 4a &, 407C & 40A /4 /4 /4 / / / - 0 - - 0 7- - 4 0 7-0 0 Q Based on 86 F liquid line temperature and a refrigerant flow of. pounds per minute per ton of Refrigerant 4a;.9 pounds per minute per ton of Refrigerant ;.9 pounds per minute per ton for Refrigerant 404A;.9 pounds per minute per ton for Refrigerant 407C;.8 pounds per minute per ton for Refrigerant 40A and 4. pounds per minute per ton for Refrigerant 07. Ratings in accordance to ARI Standard 70. W 0 drops = gram = cc. E The filtration area is equal to the core surface area plus the large internal surface available for depth filtration. Notes: R- water capacity values are approximately percent greater than R-4a. R-0 water capacities are similar to R-404A and R-07. The variation in flow ratings of filter-driers having the same size core and shell is caused by the difference in connection sizes used. For complete capacity and selection information see your Sporlan Wholesaler, our website at www.sporlan.com, or write Sporlan and request Bulletin 40-0.

Page 8 CATALOG 0, 4a, 404A, 407C, 40A, 07 Liquid Line Ratings and Selection Recommendations ESURFACE FILTERING AREA Square WRATINGS AT ARI STANDARD CONDITIONS WATER CAPACITY DROPS R- 60 PPM R-4a R-404A & 07 QREFRIGERANT FLOW CAPACITY Tons at psi P SELECTION RECOMMENDATIONS (Tons) REFRIGERATION COMMERCIAL & LOW TEMPERATURE EQUIPMENT AIR CONDITIONING FIELD REPLACEMENT or FIELD BUILT UP SYSTEMS 7 F F 7 F F 7 F F 4a & 404A 07 4a & 404A, 0 &07 4a & REPLACEABLE CORE WITH STANDARD CORES (See page 0) C-48-G 4.6.4 9.8 7-0 7-7- 0 C-487-G 64 47 88 8 47 408 09.9.9 6.0 0 C-489-G 4. 9. 8.9 0 0 C-967-G 9..9 6. 0 0 8 694 76 66 946 86 68 C-969-G 48.7 44..6 C-449-G 9. 4. 9.7 0 40 0 0 40 9 04 864 749 49 4 97 C-44-G 67.0 6. 44.8 40 0 40 0 C-9-G 84. 77. 6. 0 70 0 0 70 C-9-G 6 88 89 6 6 99.0 90.6 66. 60 80 60 80 C-97-G 04 9. 69. 6 8 60 6 8 C-00-G 94 670 878 9 009 6 99 0 74. 7 00 70 7 00 C-4007-G 9 60 04 6 40 08 6 4 96.8 0 0 00 0 0 ESURFACE FILTERING AREA Square R- 60 PPM WRATINGS AT ARI STANDARD CONDITIONS WATER CAPACITY DROPS R-4a R-404A & 07 R-407C R-40A QREFRIGERANT FLOW CAPACITY Tons at psi P 7 F F 7 F F 7 F F 7 F F 7 F F 4a 404A & 07 407C 40A & 4a SELECTION RECOMMENDATIONS (Tons) REFRIGERATION COMMERCIAL & LOW TEMPERATURE EQUIPMENT 404A, 0 & 07 AIR CONDITIONING FIELD REPLACEMENT or FIELD BUILT UP SYSTEMS REPLACEABLE CORE WITH HIGH WATER CAPACITY CORES (See page 0) C-R44-G.4 0.4 7.6 0. C-R4-G 67 90 7 98 706 049 8 760 4.7. 9.. C-R47-G 8. 6.9.4 7.0 7-7- 0 C-48-G 4.6.4 9.8. 4. 7-0 7-7- 0 0 C-487-G 64 09 904 0 868 90 049 94 0 48 6.9.9 6.0.0. 0 C-489-G 4. 9. 8.9 9.8 4. 0 0 C-967-G 9..9 6. 6. 8. 0 0 8 8 808 40 76 80 098 868 60 96 7 C-969-G 48.7 44..6 44.8 47. C-449-G 9. 4. 9.7 4.6 7.9 0 40 0 0 40 40 9 7 7 60 604 870 47 80 90 44 08 C-44-G 67.0 6. 44.8 6.7 6.4 40 0 40 0 0 C-9-G 84. 77. 6. 77.7 8.4 0 70 0 0 70 70 C-9-G 6 446 66 4804 47 60 496 76 04 94 444 99.0 90.6 66. 9. 96.6 60 80 60 80 80 C-97-G 04 9. 69. 9.7 0 6 8 60 6 8 8 C-00-G 94 6786 77 0 7890 647 76 844 0 74. 0 7 00 70 7 00 C-4007-G 9 9048 776 98 7080 00 86 76 48 4 96.8 0 0 00 0 0 Q Based on 86 F liquid line temperature and a refrigerant flow of. pounds per minute per ton of Refrigerant 4a;.9 pounds per minute per ton of Refrigerant ;.9 pounds per minute per ton for Refrigerant 404A;.9 pounds per minute per ton for Refrigerant 407C;.8 pounds per minute per ton for Refrigerant 40A and 4. pounds per minute per ton for Refrigerant 07. Ratings in accordance to ARI Standard 70. W 0 drops = gram = cc. E The filtration area is equal to the core surface area plus the large internal surface available for depth filtration. Notes: R- water capacity values are approximately percent greater than R-4a. R-0 water capacities are similar to R-404A and R-07. The variation in flow ratings of filter-driers having the same size core and shell is caused by the difference in connection sizes used. & 4a & 407C 40A For complete capacity and selection information see your Sporlan Wholesaler, our website at www.sporlan.com, or write Sporlan and request Bulletin 40-0.

CATALOG 0 Page 9 Suction Line Filter-Drier Ratings for New Systems and Clean-up after Burnout Selection Instructions Except for the values in bold (R-/R-407C/R-40A at 40 F; 8 psi pressure drop), the flow capacities are rated at the maximum recommended pressure drop for permanent installation. To ensure the suction line filter-drier has ample contaminant removal ability, selection must be based on flow capacity and the amount of desiccant required for system clean-up. The suction line filter-drier must be large enough to adequately remove acid, moisture and solid contaminants without causing nuisance plug-ups. Sizing is especially important for sealed type, 4a, 404A, 407C, 40A, 07 suction line filter-driers since they should be sized to clean a small system with one service call. To reduce the pressure drop through replaceable core shells, substitute cores with filter elements (see page 0) after the system has been cleaned up. The 67- screen should be discarded when cores are replaced with RPE-48-BD elements in RSF shells. For complete description of the suggested system clean-up procedure, request Bulletin 40-0. Suction Line Flow Capacity (Tons) Sealed Type REFRIGERANT 4a 404A 407C 40A EVAPORATOR TEMPERATURE 40 F 0 F 0 F -0 F -40 F 40 F 0 F 0 F 0 F 0 F -0 F -40 F 40 F 40 F PRESSURE DROP (psi).0.0..0 0..0..0.0..0 0..0.0 C-08-S-T-HH.. 0.9 0. 0.. 0.9 0.. 0.8 0. 0..0.7 C-084-S-T-HH.. 0.9 0. 0..4 0.9 0.6. 0.8 0. 0...7 C-44-S-T-HH.. 0.9 0.4 0.. 0.8 0. 0.9 0.6 0. 0...7 C-4-S-T-HH.4..4 0.8 0.4.. 0.8.6.0 0.6 0..4 4.6 C-46-S-T-HH 4.8.0.0. 0.6.9.8...4 0.9 0.4 4.8 6. C-47-S-T-HH.... 0.7....4.6 0.9 0.. 6.8 C-49-S-T-HH 7.0 4.4.9.7 0.9 4..7.6... 0.6 7.0 9.0 C-64-S-T-HH.7.7. 0.7 0..7. 0.7.6.0 0.6 0..7.6 C-6-S-T-HH..0. 0.8 0.4.0. 0.8.9. 0.7 0.4. 4. C-66-S-T-HH 4.0..6.0 0..6.7.0.4.6 0.9 0..9. C-67-S-T-HH 4..8.8. 0..8.8..7.7.0 0. 4.4.9 C-0-S-T-HH.4..4 0.8 0.4..4 0.8.0. 0.8 0.4.4 4.4 C-06-S-T-HH 4.4.8.8. 0..8.8..7.7.0 0. 4.4.8 C-07-S-T-HH.... 0.6.4....0. 0.6. 7.0 C-09-S-T-HH.9.7.4. 0.7.8.4..6..4 0.7.8 7.7 C-47-S-T-HH 6.0.8.. 0.7.8...6..4 0.7 6.0 7.9 C-49-S-T-HH 6..9.. 0.8 4.0.6.6.7.4. 0.7 6. 8.0 C-47-S-T-HH 8.0.0..0.0... 4.8..9 0.9 7.9 0.4 C-49-S-T-HH 0.0 6. 4... 6.4 4.. 6.0.9.4. 9.9. C-4-S-T-HH. 6.9 4.6.7.4 7. 4.6.8 6.7 4..6. 0.9 4.4 C-4-S-T-HH. 7.6.0.0. 7.8.. 7. 4.7.9.4.0.9 C-607-S-T-HH 6.7 4..7.6 0.8 4..7.7 4.0.6.6 0.8 6.6 8.7 C-609-S-T-HH 7. 4.7..8 0.9 4.8..9 4..9.8 0.9 7.4 9.8 SEALED Suction Line Flow Capacity (Tons) Shells with Replaceable Cores REFRIGERANT 4a 404A & 07 407C 40A EVAPORATOR TEMPERATURE 40 F 0 F 0 F -0 F -40 F 40 F 0 F 0 F 0 F 0 F -0 F -40 F 40 F 40 F PRESSURE DROP (psi).0 8.0*.0..0 0..0..0.0..0 0..0 8.0*.0 8.0* RSF-487-T 0. 7. 6. 4... 6.4 4.. 6. 4.0.. 0.0 7..6.9 RSF-489-T.. 7.6.0.0. 7.8.. 7. 4.8.8.4.0 0.7. 6.4 RSF-48-T 4.8.6 9. 6..6.8 9.4 6..7 8.9.8.4.7 4.6. 8..0 RSF-48-T.9 7. 0.0 6..9.9 0. 6.7 4.0 9.6 6..6.8.7 7. 9.9 4.4 RSF-487-T 7. 9.8 0.8 7. 4...0 7. 4.4 0.4 6.8.9.0 7.0 9.4. 7. RSF-48-T 8.6..6 7.6 4.6..9 7.8 4.7. 7. 4.. 8.4.6. 40. RSF-96-T.8 9.0.9. 7..9 4. 0. 6.7 4.4 9.8 6...9 7.6 9.8 48.8 RSF-96-T 9.7 49.0 9.8.7 8.7 4.7..0 8. 7.9. 7.6 4.0 8.6 47. 7. 6. RSF-967-T 9.7 49.0 9.8.7 8.7 4.7 6..0 8. 7.9. 7.6 4.0 8.6 47. 7. 6. RSF-96-T 9.7 0.7 9.8.7 8.7 4.7 8.7.0 8. 7.9. 7.6 4.0 8.9 49.8 7. 6. RSF-96-T 0.0.9 0.0.7 8.7 4.7 9..0 8. 7.9. 7.6 4.0 9.7.0 7. 6.4 C-00-G 6.6 46.0 6.7 0.9 6.. 6.9.0 6.7 6.0 0. 6.. 6. 4.8. 64.9 C-007-G 7.0 46.7 6.9. 6.6. 7.. 6.8 6. 0.4 6.. 6.7 4..8 8.4 C-4007-G.9 6.9 0.6. 8. 4.0.0.6 8. 9.8.8 7..8.4.8 4. 7. C-400-G C-400-G.9 6.9 0.6. 8. 4.0.0.6 8. 9.8.8 7..8.4.8 4. 7. *Denotes TEMPORARY INSTALLATION. Cores for system clean-up; RPE-48-BD or RPE-00 Filter Elements should be installed after clean-up. Rated in accordance with ARI Standard 70. For a simplified Quick Selection Guide, request Form 40-09. REPLACEABLE CORE

Page 0 CATALOG 0 Significance of the Type Number The letters and numerals in the Catch-All type number each have a significance. The C indicates Catch-All. The FIRST TWO OR THREE DIGITS indicate cubic inches of desiccant. The LAST ONE OR TWO DIGITS indicate fitting size in eighths of an inch. For sealed models, a -S following the last digit indicates solder fittings, and NO LETTER indicates a flare fitting. Replaceable core models (C-40 and larger) only have solder connections and the -S is omitted. Examples are: C-08 is 8 cu. in. and /8 flare, C-09-S is 0 cu. in. and solder, C-9-G is 9 cu. in. and -/8 solder. Other suffix letters indicate special qualities. For example: -T indicates a pressure tap consisting of a Schrader type access valve on the inlet end of the Catch-All. -HH indicates a charcoal style core for wax removal and clean-up after a hermetic motor burnout. -F indicates a female flare outlet fitting with a male flare inlet fitting. -FM indicates a female flare inlet fitting with a male flare outlet fitting. -CAP indicates a Catch-All particularly designed for installation on capillary tube systems. Replaceable Cores and Pleated Filter Elements Order Separately Cores for replaceable core type filter-driers are molded of exactly the same desiccants that are used in the popular sealed filter-driers. Cores are individually packed in metal cans, fully activated and hermetically sealed against moisture and dirt. Filter Elements are dried and packed in individual sealed metal cans. This method of packaging prevents the element from picking up moisture from the atmosphere. Detailed instructions are printed on each can. Each can contains a triple gasket consisting of a new end plate gasket, an end plate gasket for certain competitive filter-driers and a core gasket where desired. See the specifications on page 6 for the number of cores required for each type drier. RCW-4 High Water Capacity Core Order as separate item Fits ONLY shell type C-R44, C-R4 and C-R47. Designed specially for use with POE oils. This core should be used on systems that have a ruptured water cooled condenser, or that have been exposed to the atmosphere, or for some reason have a high amount of moisture in the system. RC-4864 Activated Core Order as separate item Fits types C- 480 C-900 Series shells and Replaceable Suction Filter (RSF) shells. This is the standard core suitable for most installations in the liquid or suction line applications. RCW-48 High Water Capacity Core Order as separate item Fits types C-480 C-900 Series shells and Replaceable Suction Filter (RSF) shells. Designed specially for use with POE oils. This core should be used on systems that have a ruptured water cooled condenser, or that have been exposed to the atmosphere, or for some reason have a high amount of moisture in the system. RC-4864-HH Activated Charcoal Core Order as separate item Fits types C-480 C-900 Series shells and Replaceable Suction Filter (RSF) shells. This core should be used for wax removal on low temperature systems, and for clean-up of systems that have had a hermetic motor burnout. RPE-48-BD Filter Element Order as separate item Fits types C-480 C-900 Series shells and Replaceable Suction Filter (RSF) shells. This element should be used in RSF shells installed in the suction line to obtain the lowest possible pressure drop. In cleaning up a system after a hermetic motor burnout, cores should be used first. Then after the system is thoroughly clean, this filter element can be installed in the RSF shell. RC-0098 Activated Core Order as separate item Fits types C-0000 and C-40000 Series shells. This core has a high water capacity and should be used on all standard liquid and suction line applications. RCW-00 High Water Capacity Core Order as separate item Fits types C-0000 and C-40000 Series shells. Designed specially for use with POE oils. This core should be used on systems that have a ruptured water cooled condenser, or that have been exposed to the atmosphere, or for some reason have a high amount of moisture in the system. RC-0098-HH Activated Charcoal Core Order as separate item Fits types C-0000 and C-40000 Series shells. This core should be used for wax removal on low temperature systems, and for clean-up of systems that have had a hermetic motor burnout. RPE-00 Filter Element Order as separate item Fits types C- 0000 and C40000 Series shells. This filter element should be used in the suction line to obtain the lowest possible pressure drop after cores were used for system clean-up. HH Style Catch-All for Wax Removal Small amounts of wax are often a problem on low temperature systems. Even well engineered systems frequently contain minute quantities of wax which are sufficient to clog expansion valve screens or cause sticking of the valve. Sporlan has developed a special blend of desiccants including activated charcoal which removes small amounts of wax in the liquid line before this wax can cause trouble at the expansion valve. These Catch-All Filter-Driers have been very successful in correcting trouble jobs in the field. Select an HH Style Catch-All Filter-Drier if wax problems occur on low temperature systems. In addition to their wax removal ability, these filter-driers will remove all of the other harmful contaminants that the standard filter-driers remove. Listed in the table are various Catch-All models that incorporate the HH style core. CONNECTIONS CONNECTIONS C-0-HH /4 SAE Flare C-0-HH /8 SAE Flare C-08-HH /4 SAE Flare C-04-HH SAE Flare C-08-HH /8 SAE Flare C-04-S-HH ODF Solder C-6-HH /4 SAE Flare C-0-HH /8 SAE Flare C-6-HH /8 SAE Flare C-0-S-HH /8 ODF Solder C-6-S-HH /8 ODF Solder C-44-HH SAE Flare C-64-HH SAE Flare C-4-HH /8 SAE Flare C-64-S-HH ODF Solder C-47-S-HH ODF Solder C-6-HH /8 SAE Flare RC-4864-HH Replaceable C-6-S-HH /8 ODF Solder RC-0098-HH Core For dimensions, refer to the specifications for standard filter-driers or consult Bulletin 40-0.