Take control with... Energy Efficient Controls

Take contro with... Energy Efficient Contros 1

A LEGACY OF ENERGY EFFICIENCY AND COST SAVINGS Nuaire and ventiation contros go back a ong way, starting from the days when the thenowner Brian Moss was a eading figure in the Buiding Services Industry eventuay becoming Chairman of CIBSE. In the eary 1970s the word was facing the first oi crisis, and it became obvious that the high quantities of carbon emissions being reeased into the atmosphere were destroying the panet. A fair proportion of these emissions coud be attributed to eectric motors running inefficienty without contros and wasting vauabe energy resources. Historicay, fans and motors had to have a transformer or eectronic speed controer fitted remotey and wired back to the unit, introducing additiona cost and wasting time on site when energy seemed cheap and pentifu and no one knew about the damage to the environment, many contractors and consutants woud seect a fan product as cose as they coud to the design duty and not insta the speed contro. This saved the wiring and contro costs but didn t make the energy savings needed. Brian Moss, as a eader of CIBSE and with an understanding of these wastefu practices, had the foresight to instruct his Nuaire Engineering team to deveop a simpe contro system that coud be fitted to the fans we produced that woud give contractors and consutants the toos needed to operate fans at the correct speed, providing a simpe and cost effective way to save energy and reduce running costs. 1972 1982 MICROSAVE was born in 1972 as a contro concept for Nuaire s market eading Twin fan range and incorporated extra ow votage wiring between fans and controers, auto changeover faciity and simpe speed contros. Not ony did this save in wiring costs but it aso provided the customers and contractors with the abiity to correcty set the speed for the fan - therefore saving energy and running costs. The Microsave concept was ess wiring, ess space, ess expense - something that Nuaire has kept as its key principe for a of its contros since 1972. MICROSAVE NETLINK foowed in the eary 80s, as customers demanded more accurate energy contro, improved comfort in buidings and ever ower instaation costs. Netink was designed to fuy integrate with a range of matched sensors and detectors and to offer an inexpensive contro soution providing comfortabe conditions deivering energy savings for a fraction of the price of an Energy Management System. SMART, deveoped in 1992 saw the introduction of a fu range of room and duct mounted sensors combined with wa mounted controers inked by our Safe extra ow votage (SELV) wiring to fans and heat recovery units with onboard speed contros. A revoution in comfort contro and energy saving for ventiation products used in decentraised spaces. SMART became the UK s most used energy saving contro for this type of appication, as consutants, contractors and cients reaised they coud have the same contro functions of a Buiding Management System on smaer schemes, without the additiona cost of compicated contros. SMART coud ink severa fans together, speed contro them in proportion to the temperature or humidity provide on/off timed sequences and sti report fan faiures to a contro pane. ECOSMART was a natura evoution from SMART contros. Launched in 2002, it has now become one of the UKs eading energy efficient contro systems for the decentraised ventiation market. This eary era was a time of change as consutants worked with architects to produce buidings with ower energy footprints and improved buiding enveopes in an effort to reduce energy and conserve fues. Large AHU systems went out of fashion and individua room/ zone ventiation became common, which is where ECOSMART found its natura home. It was obvious that the way forward was for consutants to have the abiity to specify a fan/hru that coud be instaed with its own contro system and that coud have a wide range of sensors pugged in to give contro over CO2, temperature and humidity. The fact that this ECOSMART system is a standaone contro fitted to neary a Nuaire products, featuring time cocks, presence detectors and sensors, with the option to be inked to a BMS at an affordabe cost was not missed by the consutants and contractors and ECOSMART became synonymous with on-board contro systems, and created a bench mark for the industry. 2 029 2085 8200

1992 2002 2008 2015 In recent years, ever increasing energy bis and tighter contros on emissions have ed to stricter Buiding Reguations, raising the bar required to deiver sweeping improvements to the buit environment. This, couped with an ever growing demand for tighter contro and coser integration of buiding services equipment has ed Nuaire, once again drive the market forward with a ground breaking contro soution, ECOSMART CONNECT. Nuaire was the first ventiation manufacturer to introduce ow votage energy saving contro systems onto its products. Nuaire continues to ead the industry by expanding the proven ECOSMART contros patform with new ECOSMART CONNECT and ECOSMART ADAPT network contro soutions. CONTENTS PAGE LEGISLATION 4 ECOSMART CONTROL PLATFORM 5-7 BASIC CONTROL (BC) 8 ECOSMART CLASSIC was the first pug and pay contro on the market and has been a core Nuaire product for the ast 13 years. ECOSMART CONNECT enhances Nuaire's offering with fu BMS integration via BACnet MS/TP (expandabe to IP with additiona router). Mutifunction sensors are avaiabe in one sma compact unit. ECOSMART CLASSIC CONTROL (ES) 10 ECOSMART CONNECT CONTROL (CO) 18 ECOSMART ADAPT provides a totay ADAPTABLE soution specific to site requirements aowing other eading controers such as Siemens, Cyon and Schneider to be incorporated. A controers are functionay tested before eaving Nuaire s manufacturing faciity. ECOSMART ADAPT CONTROL (AT) 50 nuaire.co.uk 3

ECOSMART CONTROLS LEGISLATION Approved Document Part L (2013) and section 6 (2015) of the Scottish Buiding Reguations states that Fixed buiding services sha have effective contros and that contro strategies shoud be organised such that priority is given to the east carbon intensive energy source. Buiding contros are being asked to moderate and minimise energy use in a buiding, with the reguations stating that buiding service systems shoud be provided with appropriate contros to enabe the achievement of reasonabe standards of energy efficiency in use. Under norma circumstances, this egisation suggests that the foowing features woud be appropriate for heating, ventiation and air conditioning system contros: The systems shoud be subdivided into separate contro zones to correspond with each area of the buiding that has a significanty different soar exposure, usage pattern or type of use. Each separate contro zone shoud be capabe of independent timing and temperature contro and, where appropriate, ventiation and air recircuation rate. The provision of the service shoud respond to the requirements of the space it serves. If both heating and cooing are provided, they shoud be controed so as not to operate simutaneousy. Centra pant shoud operate ony as and when the zone systems require it. The defaut condition shoud be off. In accordance with the requirements of Part L and section 6 of the Scottish Buiding Reguations, Nuaire provide the optimum contro avaiabe, combined with the most efficient use of energy. Exampe: For a centra mechanica ventiation system with heating and cooing, and heat recovery via a pate heat exchanger pus return air fiter: SFP = 1.6 + 0.3 + 0.1 W/(/s) = 2.0 W/(/s) Tabe 37: Recommended minimum contros for air distribution systems in new and existing buidings from BS EN 15232:2012. Refer to Ecosmart Contro Patform for fu range (see opposite). System type Contros package Centra mechanica ventiation with heating, cooing or heat recovery Air fow contro at room eve Air fow contro at air hander eve Heat exchanger defrosting contro Heat exchanger overheating contro Suppy temperature contro Time contro On/off time contro Defrost contro so that during cod periods ice does not form on the heat exchanger Overheating contro so that when the system is cooing and heat recovery is undesirabe, the heat exchanger is stopped, moduated or bypassed Variabe set point with outdoor temperature compensation Centra mechanica ventiation with heating, or heat recovery Air fow contro at room eve Air fow contro at air hander eve Heat exchanger defrosting contro Heat exchanger overheating contro Suppy temperature contro Time contro On/off time contro Defrost contro so that during cod periods ice does not form on the heat exchanger Overheating contro so that when the system is cooing and heat recovery is undesirabe, the heat exchanger is stopped, moduated or bypassed Demand contro Zona Air fow contro at room eve Air fow contro at air hander eve Suppy temperature contro On/off time contro No contro No contro Loca Air fow contro at room eve Air fow contro at air hander eve Suppy temperature contro On/off No contro No contro 4 029 2085 8200

ECOSMART CONTROLS PLATFORM DEMAND VENTILATION SOLUTIONS DESIGNED FOR EFFICIENCY AND PERFORMANCE Nuaire have a pedigree for designing and manufacturing energy efficient ventiation equipment and matched contro systems. Our very first contro was produced in 1972. Nuaire was the first manufacturer to introduce ow votage energy saving contro systems. Its fans with Smart technoogy varied the ventiation rate to suit occupant eves. Ecosmart was aunched in 2002 and revoutionised the industry by providing the first pug and pay contro system. Designed to meet site/project requirements - Ecosmart Adapt (with Trend) is the standard contro. For other options contact Nuaire. Ecosmart Adapt (with Trend) is fitted with an IQ422/12/LAN/BAC/230 controer aowing for unitary contro and fu BMS integration via BACnet IP (by others). Controer software is basic and ready for project specific program to be oaded. Ecosmart Adapt (with Trend) has a 5 year warranty. Nuaire continues to ead in the industry with the expansion of their Ecosmart Contros Patform. NEW Energy efficient demand based contro providing network connectivity and advanced functionaity. Fu BMS integration via BACnet MS/TP (by others). Ecosmart Connect is expandabe to IP network (separate connection box) contact Nuaire for detais. Ecosmart Connect has a 5 year warranty. The UK s eading Energy Efficient pug and pay soution for over 13 years. Ecosmart Cassic provides 0-10V BMS interface, tricke and boost as standard. Ecosmart Cassic has a 5 year warranty. THE MOST SUCCESSFUL ENERGY CONTROL EVER - DEMAND VENTILATION AT YOUR FINGER TIPS BASIC CONTROL Suppied with a simpe termina box for suppy and extract fan motor wiring and for interfacing to custom buit contro panes (by others). Basic contro has a 2 year warranty. nuaire.co.uk 5

BASIC & ECOSMART CONTROLS PLATFORM BASIC CONTROL (BC) (ES) (CO) BACnet (MS/TP) (AT) Based on TREND IQ422 BACnet (IP) CONTROLLER SOFTWARE Controer Software N/A Advanced Software Basic Software (Can be re-written by others) Heat Exchange Bypass Contro Strategy Basic Optimised Basic Suppy Temperature Contro Strategy Yes Yes Yes Room Temperature Contro Strategy No Yes No Switched Live Enabe Input Yes Yes Yes Switched Live Fan Boost No No Yes Switched Live Configurabe Input No Yes No (Heat or Fan Boost) Vot Free Enabe Input No Yes Yes Vot Free Fan Boost No No Yes Vot Free Configurabe Input No Yes No (Heat or Fan Boost) Tricke Mode Yes Yes Yes Fan Run-On Yes Yes Yes Fan Run-On (Inteigent) No Yes No Run/Faut/Heat/Coo Vot Free Outputs Yes Yes Yes I/O Damper contro Yes Yes (via run reay) Yes (via run reay) Heat Dissipation Run- on Yes Yes Yes Frost Protection Routine Yes Yes Yes Low Suppy Temp Fan Cut-out No Yes Yes Scheduing Yes via ES-LCD Yes Yes CO2 Based Fan PID Loop ES Co2 Yes Yes Humidity Based Fan PID Loop ES-HUM Yes No Pressure Based Fan PID Loop CP version avaiabe Yes No Night Cooing Mode No Yes Yes Purge Mode No Yes Yes Hibernate Mode (Open a vaves) No Yes No Fan Speed Adjustment Yes Yes Yes Fan Speed Contro ony Yes No No No 0-10V Fan speed Input Yes Yes Yes 0-10V Temperature Sensor Input No Yes No 0-10V Humidity Sensor Input No Yes No 0-10V Pressure Sensor Input No Yes No 0-10V CO2 Sensor Input No Yes No CONTROLLER HARDWARE Fai safe therma trip Yes Yes Yes Condensate Pump Monitoring Yes Yes Yes Din Rai Mounted Contro No Yes Yes Quick Connect Terminas No Yes Yes 24VAC Auxiiary No Yes Yes 6 029 2085 8200

BASIC & ECOSMART CONTROLS PLATFORM BASIC CONTROL (BC) (ES) (CO) BACnet (MS/TP) (AT) Based on TREND IQ422 BACnet (IP) HMI Commissioning Dispay Yes ony Via Yes By Others commissioning PCB BACnet LCD Touch Screen Dispay No Yes By Others ROOM MODULES Pug & Pay Sensors Yes Yes No Max Number of Sensors 31 devices on any system 4 sensor modues* By Others Quick connect pugs Yes Yes By Others Twisted pair cabe compatibe No Yes By Others Commissioning Port No Yes By Others Temperature Yes Yes By Others CO2 Yes Yes By Others Humidity Yes Yes By Others 3-Speed Override No Yes By Others PIR Yes Yes By Others Setpoint Adjust Yes (on sensor) Yes By Others Mutipe Setpoints Supported No Yes By Others Room Temperature Dispay No Yes By Others Room Humidity Dispay No Yes By Others Fan Speed Dispay No Yes By Others Occupancy Status Dispay No Yes By Others Network Error Dispay Yes Yes By Others NETWORKING BEMS compatibe No Yes Yes BMS compatibe 0-10V Input BACnet via MS/TP (BACnet via IP) (BACnet via IP optiona) MONITORING Web connectivity NA Yes Yes Energy Monitoring NA Yes Participation via Trend network Energy Metering NA Yes Participation via Trend network *Each sensor modue can have mutipe sensors. (up to 3 per modue). For further detais of Ecosmart Contros Patform, refer to website: www.nuaire.co.uk nuaire.co.uk 7

BASIC CONTROL OPTION (BC) Basic Contro - Suppied with a termina box for Suppy and Extract fan motor wiring and for interfacing to customer buit contro panes (by others) Doesn t cost the Earth... Doesn t cost the Earth... 8 029 2085 8200

BASIC CONTROL CONSULTANTS SPECIFICATION BASIC CONTROL OPTION - FAN SPEED ONLY Basic contro is fan speed ony and are suitabe for 2-10V adjustment (by others). The heat recovery (XBC) or packaged air handing unit (BPS) wi have a side mounted termina box for connection to the fans (230V, 50Hz LNE and 2-10V*) and bypass actuator (where appicabe). Basic contro is for BMS by others. Basic contro has a 2 year warranty. *For XBC 75 and XBC 85 (400V 3ph, 50Hz LNC and 2-10V). BASIC CONTROL OPTION - XBC RANGE Unit is provided with side access termina boxes for direct suppy and extract fan motor wiring and for interfacing to custom buit contro panes. The contro assemby is side mounted with a 90 O rotation faciity (XBC ony) for wiring and commissioning adjustments in restricted access conditions. (260mm access aowance is required). A side mounted termina box is provided for the connections to the fans (230V 50Hz LNE and 2-10V), and Eectric heater termina and therma protection (where specified). For this option, no sensors are fitted to the unit, but note that the pate heat exchanger bypass damper actuator is incuded suitabe for 230V standard (24V avaiabe). Doesn t cost the earth... Units fitted with Basic Contro (code exampe XBC25-H-EBC or BPS17-T-EBC) have a 2 year warranty. The unit sha be the XBC (Heat Recovery Range) or BPS (Boxer Packaged Soution) as manufactured by Nuaire. nuaire.co.uk 9

ECOSMART CLASSIC (ES) CONTROL OPTION Ecosmart Cassic Contro - UK s eading Energy Efficient Pug and Pay soution for over 13 years. Provided with 0-10V BMS interface, tricke and boost as standard Doesn t cost the Earth... Doesn t cost the Earth... 10 029 2085 8200

INDEX FOR CONTROL PAGE ECOSMART CLASSIC - FEATURES AND BENEFITS 12 ECOSMART CLASSIC - HOW IT WORKS 12 ECOSMART CLASSIC - SENSORS AND ENABLERS 13-16 ECOSMART CLASSIC - CONSULTANTS SPECIFICATION 17 Doesn t cost the earth... nuaire.co.uk 11

ECOSMART CLASSIC CONTROL (ES) FEATURES & BENEFITS QUICK & EASY TO INSTALL - A contros are pre-assembed, configured and instaed directy into the fan or air handing unit, this incudes 2, 3 or 4-port motorised vaves and actuators, pipework, off coi thermostats and sensors, frost protection, etc. Site time kept to a minimum, quaity and efficiency maintained. EASILY ADJUSTABLE - No need for main VCD, which means no wasted energy or noise generation because the air voume can be precisey set via the integrated speed contro, minimum and maximum speeds easiy adjusted via Ecosmart commissioning pane. SIMPLE, PRECISE COMMISSIONING - As recommended in Part L, Ecosmart Cassic enabes the system to be accuratey commissioned via an integrated speed contro, minimum and maximum speeds easiy adjusted via commissioning pane integra to the contro. Ventiation mode Cooing mode* Heating mode* Loca contro 0.00 - - OFF / tricke 0.25 - - Speed 1 0.50 0.75 1.00 Speed 2 1.50 1.75 2.00 Speed 3 2.50 2.75 3.00 Speed 4 3.50 3.75 4.00 Speed 5 4.50 4.75 5.00 Speed 6 5.50 5.75 6.00 Speed 7 6.50 6.75 7.00 Speed 8 7.50 7.75 8.00 Speed 9 8.50 8.75 9.00 Speed 10 9.50 9.75 10.00 * Ony avaiabe on reevant unit. QUIETER SYSTEM - With Ecosmart Cassic your system (when combined with sensor) is ony at maximum design duty when absoutey necessary. The noise eves within your systems are ower because the fans or air handing units are rarey at fu speed. IMPROVED LIFECYCLE - Ecosmart Cassic enabes the fan or air handing unit to be run at ower speeds. This reduces the maximum oad and wear and therefore increases the overa working ife of the units. DEMAND VENTILATION - To achieve maximum potentia savings and the owest possibe energy consumption, combine Ecosmart Cassic with sensors to ink the fan speed directy to demand. For exampe by using ES-CO2 or temperature sensors to contro fan speed when a room is occupied. HEALTHY ATMOSPHERE - Ecosmart Cassic has a tricke function as standard which when activated, via a simpe switch, enabes you to set a background ventiation rate, keeping the rooms fresh when unoccupied, whist sti saving energy. System wi boost or ramp to maximum design duty when triggered by an Ecosmart or other externa device. PLUG IN CONTROLS - Simpe ow votage sensors compete with prepugged cabe means that any contro function is easiy achieved. You decide which conditions to monitor and the system wi operate at the optimum speed. BASIC BMS INTERFACE - Integrated BMS features enabe any centra system to contro and monitor the fan or air handing unit via 0-10V signa. This enabes fu speed contro and heating or cooing enabe if instaed and vot free status indication as standard. PEACE OF MIND - Warranty is extended to 5 years with Ecosmart Cassic. Basic contro units ony carry a 2 year warranty. 1 9 3 CONVENTIONAL SUPPLY & EXTRACT VENTILATION SYSTEM Extract unit 3 8 2 Suppy unit 10 8 7 8 4 1. PVC tubing 2. Fiter 3. Air pressure switch 4. Temperature switch 5. Contro pane 6. User contro 7. 230V Eectricity suppy 8. Eectrica cabing 230V 9. Eectrica heater 10. Time cock 6 5 1 Extract unit 4 ECOSMART SUPPLY & EXTRACT VENTILATION SYSTEM 2 1 3 6 Suppy unit 5 1. Integrated contro 2. Optiona CO 2 sensor 3. User contro 4. (SELV) 12V cabe 5. Optiona PIR sensor 6. 230V Eectricity suppy 12 029 2085 8200

ECOSMART CLASSIC CONTROL (ES) SENSORS & ENABLERS A Ecosmart Cassic Systems must incude at east one enaber. (N.B. when used, BMS contro and time cocks take over a other enabers). ES-PIR2 (Enaber) Detects movement and activates system. Incorporates a system status LED, overrun timer and timer adjustment. ES-TEMP2 TEMPERATURE (Sensor) Moduate fan speed based on room temperature. Incorporates two system status LEDs. (Green = OK, Red = Faiure) and temperature set point eve adjustment. ES-THERMOSTAT2 (Enaber) Activates the system when the temperature is above set point. Incorporates two system status LEDs. (Green = OK, Red = Faiure) and temperature set point eve adjustment. ES-RH2 RELATIVE HUMIDITY (Sensor) Moduate fan speed based on RH eve. Incorporates two system status LEDs. (Green = OK, Red = Faiure) and RH set point eve adjustment. ES-AVI2 (Enaber) When fan faiure occurs the AVI wi fash a warning. Suppied with pre-pugged 10m ength of communication cabe. ES-CI SEMI-AUTOMATIC USER CONTROL Fan, heating & cooing seected by externa vot free switch, speed seected by 0-10V signa. ES-HUMIDISTAT2 (Enaber) Activates the system when the RH eve is above set point. Incorporates two system status LEDs. (Green = OK, Red = Faiure) and RH set point eve adjustment. ES-JB JUNCTION BOX Designed to be compatibe with Ecosmart System this unit is suppied with a prepugged 10 metre ength of communications cabe and has 8 further ports. ES-CO2RM (Sensor) ES-CO2RMPP (Sensor) Surface mounted room carbon dioxide (CO2) sensors incorporate a temperature sensor. RM = SELV option, RMPP compete with SELV AC powers suppy. ES-CO2 (Sensor) Duct mounted sensor to moduate fan speed based on CO2 eves. Connect to fan directy. Pre-wired with 2m cabe (not adjustabe). ES-HTCSIG (Enaber) Signa conditioning circuit for humidity, temperature and CO2 sensors. SWITCHED LIVE (by others) Any mains votage signa connected to the switched ive termina (S/L) in the unit. This affects the connected fan ony. TOUCH SCREENS & MANUAL USER CONTROLS ES-LCD (Enaber) Touch screen user contro in white incorporating time cock faciity. This can contro the function of the fan by manua setting or using a set of timed programs. ES-UCF Manua on and off system user/speed contro. Incorporates two system status LEDs (Green = OK, Red = Faiure). nuaire.co.uk 13

ECOSMART CLASSIC CONTROL (ES) SENSORS & ENABLERS ECOSMART, BMS AND COMMISSIONING CONTROL OPTIONS Nuaire fans and Air Handing Units can be provided with the foowing preseected contro options, simpy and easiy by adding etters to the end of the fan code, there is no need to seect or specify the contros individuay if one of these options are chosen : SET UP/COMMISSIONING BOX LED indicators ES ECOSMART CONTROLS The compact Ecosmart contro modue comes compete with a factory fitted Ecosmart PCB which wi contro the fan unit within the desired design parameters and provide the interface between a externa contro devices detaied on these pages. The Ecosmart contro modue has the foowing energy saving components integray mounted, pre-wired to interface with the purpose made PCB, a components pre-wired, configured and factory fitted by the manufacturer: (Not pre-wired to eg. SQF, Airmover). Integra Frequency inverter/speed controer Integra maximum and minimum speed adjustment for commissioning. Integra adjustabe run on timer. Integra BMS interfaces - 0-10V speed adjustment. Integra BMS interfaces - Vot free faiure and status indication. Integra background ventiation switch (tricke switch). Mutipe IDC sockets for interconnection of sensors or fans using pre-pugged 4-core ow votage cabe. Pre-programmed with soft start function 240V 1 ph 50Hz Switch ive signa 100-230V Damper Open 230V 1A Cose 230V 1A Neutra Return 230V signa Contacts Vot Free Run & Fai 0V = No BMS 0.25V = Off or Tricke 0.5V = Speed 1 0.75V = Speed 1 & Cooing 1V = Speed 1 & Heating Heat & coo signa via NET to ES-VF *Not incuded as standard. N L Link wire SL OP CL N F3 RET Run Run Faut Faut Ecosmart Contro Device Fan 2 Fan 1 F4 NET 0V 0-10V 0-10V BMS Signa *Sensor Important: The Fan wi not contro externa Heating/cooing equipment, wi ony provide ON/OFF Signa MIN = Minimum speed adjustment MAX = Maximum speed adjustment SL Run on = Switched Live Run-On Timer adjustment TRICKLE = Seects tricke running: 0 = off, 1 = seected TEST = Test button Min Max SL run on 0 1 Tricke The Ecosmart contro modue has the foowing two options fitted as standard. 1) BMS INTERFACES The Ecosmart contro modue can be pre-configured to provide the foowing integrated BMS interfaces. 0-10 vot input to provide a fu BMS interface. This wi enabe the foowing functions:- Switch the unit ON/OFF. Switch heating or cooing ON/OFF (AHUS with reevant cois). Switch from ow speed to high speed - variabe. Switch from ow speed to high speed - tricke and boost principe. Fu speed contro faciity. 2 No. Vot free contacts to provide fan run and faiure indication to provide system status. An integrated commissioning/speed contro to accuratey commission the system, with minimum and maximum speeds easiy adjusted via a miniature dia, as recommended in Part L. This wi enabe the unit to be configured to run between set parameters thus saving motor power and imiting noise. Pre-programmed with soft start function. 2) COMMISSIONING SET UP The Ecosmart contro modue can be pre-configured to provide the foowing integrated commissioning features ony. An integrated commissioning/speed contro to accuratey commission the system, with minimum and maximum speeds easiy adjusted via a miniature dia, as recommended in Part L. This wi enabe the unit to be configured to run between set parameters thus saving motor power and imiting noise. Minimum and max speeds easiy adjusted via miniature dia. The commissioning set up faciity directy contros the integrated speed contro/frequency inverter. Test Pwr Standby Fan 1 Fan 2 Heating Cooing Faut Frost Tx Rx 14 029 2085 8200

ECOSMART CLASSIC CONTROL (ES) SENSORS & ENABLERS ENABLING SENSORS ES-PIR2 SENSOR The sensor operates with Safe Extra Low Votage (SELV) with power suppied from the fan unit via the communications cabe. The ES-PIR sensor wi activate the system when movement is detected. An adjustabe 1-60 minute timer is incorporated to provide a run on faciity. When adjustments are made to the sensor, the LED ight on the sensor front wi fash on and off to show the set point. First, green fashes wi indicate the set point in TENS, then red fashes wi indicate UNITS. For exampe 1 green fash and 5 red fashes show you that the PIR timer is set to fifteen minutes. ES-TEMP2 TEMPERATURE SENSOR This wi moduate fan speed based on room temperature. The sensor operates with Safe Extra Low Votage (SELV) with power suppied from the fan unit via the communications cabe. After adjustments are made to the sensor, the LED ight on the sensor front wi fash on and off to show the set point. First, green fashes wi indicate the set point in TENS, then red fashes wi indicate UNITS. For exampe 2 green fashes and 3 red fashes show a temperature set point of 23ºC. Note: fan speed = 0 (i.e. off) at or beow the set point. ES-THERMOSTAT2 The ES-Thermostat wi enabe the fan when the ambient temperature is 1ºC above the set point and wi stop the fan when the temperature is at or beow set point. The sensor operates with Safe Extra Low Votage (SELV) with power suppied from the fan unit via the communications cabe. Adjusting the sensor set points. Adjustabe temperature setting 10-35ºC. After adjustments are made to the sensor, the LED ight on the sensor front wi fash on and off to show the set point. First, green fashes wi indicate the set point in TENS, then red fashes wi indicate UNITS. For exampe 2 green fashes and 3 red fashes show a temperature set point of 23ºC. ES-HUMIDISTAT2 The ES-Humidistat wi enabe the Ecosmart fan when the measured humidity eve is 2% above the set point and wi stop the fan when the humidity is at or beow set point. The sensor operates with Safe Extra Low Votage (SELV) with power suppied from the fan unit via the communications cabe. Adjusting the sensor set points - Adjustabe RH setting 65-85%. After adjustments are made to the sensor, the LED ight on the sensor wi fash indicating via a sma aperture on the side of the sensor the set point. First, green fashes wi indicate the set point in TENS, then red fashes wi indicate UNITS. For exampe 7 green fashes and 3 red fashes show a RH set point of 73%. SPEED CONTROLLING DEVICES ES-RH2 HUMIDITY SENSOR The ES-RH Sensor wi vary the ventiation rate automaticay according to the measured humidity. The sensor operates with Safe Extra Low Votage (SELV) with power suppied from the fan unit via the communications cabe. The sensor has an adjustabe 65-85% RH set point. After adjustments are made to the sensor, the LED ight on the sensor front wi fash on and off to show the set point. First, green fashes wi indicate the set point in TENS, then red fashes wi indicate UNITS. For exampe 7 green fashes and 5 red fashes show a set point of 75% RH. Note: fan speed = 0 (i.e. off) at or beow the set point SENSOR RESPONSE - Norma operation (Proportiona band over ten 10ºC steps) When temperature rises, the fans wi increase speed. (See above) which shows a set point at 19ºC. For singe phase fans, the speed steps are approximate and actua running speeds wi be dictated by the operating pressure of the system and the type of impeer used in the bower. Fan is switched off at set point uness the tricke switch is seected. ES-LCD (TIME CLOCK INCLUDED) The ES-LCD Time cock wi switch the system on and off at pre-determined times set by the user. This digita time cock wi override the user contro for effective on/off operation or any other enabing device eg. PIR. The time cock operates on Safe Extra Low Votage and is powered from the fan contro modue. The connection is made into any NET socket on the fans integra contro modue. See I&M for further detais. ES-LCD INCLUDES: Ventiation, Automatic Heating & Cooing Enabe/Disabe. Air off temperature in devices with cois is pre-set within the commissioning toos and cannot be controed remotey. ES-CO2 CARBON DIOXIDE SENSOR - OPERATION The CO2 Sensor wi adjust the fan speed in response to the CO2 concentration in the airfow.the fan speed is divided into 10 steps from minimum (step 1) to maximum (step 10). See tabe beow for response detais. Speed 1 2 3 4 5 6 7 8 9 10 CO2 PPM 502 580 659 737 834 902 980 1059 1137 1215 nuaire.co.uk 15

ECOSMART CLASSIC CONTROL (ES) SENSORS & ENABLERS ES-CI (ECOSMART CONTROL INTERFACE) Enabes any Ecosmart unit to be controed via any remote non Ecosmart switching device or item of pant. As the room CO 2 and temperature rises, the fan speed wi progressivey increase in steps unti the upper threshod vaues are reached. When both CO 2 and temperature readings are in operation, whichever reading that resuts in higher fan speed wi be used by the fan unit. Connect to fan via 4-core data cabe Fan Heat Coo STATUS PWR OV O - IOV Min Seect Max (B) Switch to seect max or min speed (A) O- IOV signa to seect fan speed ony Vot free contacts to seect heating and cooing operations Vot free contact to switch on fan The threshod vaues and other operations can be adjusted by setting DIL switches on the PCB to different positions. Note 1: As suppied; the defaut operation of the sensor wi be based on carbon dioxide reading. If operation with both carbon dioxide and temperature is desirabe then change position of switch 7 to ON. Note 2: use switch 8 to change the off state (see tabe beow). TEMPERATURE THRESHOLD SWITCHES 1-9 Switch settings 3 2 1 Threshod temperatures T1 (ºC) T2 (ºC) Off Off Off 25 28 Off Off On 24 28 Off On Off 23 28 Off On On 22 28 On Off Off 25 30 On Off On 24 30 On On Off 23 30 On On On 22 30 ES-CO2RMPP TEMPERATURE SENSOR CO 2 and temperature sensor suppied with (SELV) AC power suppy. The sensor wi monitor the carbon dioxide (CO2) and temperature (see note 1) is designed to be wa mounted within the room. If either reading reaches the ow threshod vaues (i.e. C1 & T1) see opposite, then a signa wi be sent to start running the fan at minimum speed. The ES-CO2RMPP is suppied with (SELV) AC power suppy. The ower and upper threshod vaues can be adjusted as shown in the foowing tabe. Max speed 0.15V Min speed Off See note 2 T1 or C1 CO2 T2 or C2 or Adjustabe Lower threshod Temperature signa Adjustabe Upper threshod Note: Defaut operation is CO 2 ony. To seect temperature option as we pease refer to I&M. ES-CO2RM TEMPERATURE SENSORS CO 2 and temperature sensor requires SELV power suppy by others. 16 029 2085 8200

ECOSMART CLASSIC CONTROL (ES) CONSULTANTS SPECIFICATION CONSULTANTS SPECIFICATION ECOSMART CLASSIC - DEMAND CONTROLLED VENTILATION Provides the faciity for energy saving via an inteigent stand-aone AHU function with oca diagnostic status indication, or aows convenient integration with the cient BMS with a minima co-ordination requirement. The factory fitted Ecosmart Cassic contro incudes:- Integra infinitey variabe speed /duty contro for the suppy and extract fans, with independent minimum, maximum and offset adjustment (up to 40%) for accurate commissioning. The contro assemby is side mounted with a 90 O rotation faciity (XBC Range ony) for wiring and commissioning adjustments in restricted access conditions. (260mm access aowance is required). The contro features a run on timer and background ventiation function, and is provided with unit status indication, run and fai reays and interface connections for Ecosmart Cassic sensors/enabers and system dampers. The heat exchanger bypass is automaticay operated according to temperature and a pre-defined strategy. ***The heating output (LPHW or eectric) is automaticay reguated to contro the Air - Off condition. The Ecosmart contro modue can additionay be connected to provide the foowing integrated BMS interfaces. 0-10 vot inputs wi enabe the foowing functions:- Switch the unit on/off, variabe speed / duty contro, switch from ow speed to high speed, enabe heating / cooing. 2 No. Vot free contacts give fan run and faiure unit status indication. Units fitted with Ecosmart Cassic contro have a 5 year warranty. nuaire.co.uk 17

ECOSMART CONNECT (CO) CONTROL OPTION Ecosmart Connect Contro - NEW Energy efficient demand based contro expanded to provide network connectivity and advanced functionaity. Avaiabe with a new range of BACnet compatibe Pug and Pay room sensors. Fu BMS integration via BACnet MS/TP (BACnet IP via optiona additiona router) Doesn t cost the Earth... Doesn t cost the Earth... 18 029 2085 8200

INDEX FOR CONTROL PAGE ECOSMART CONNECT - FEATURES AND BENEFITS 20 ECOSMART CONNECT - SENSORS AND ENABLERS 21-22 ECOSMART CONNECT - DESCRIPTION OF CONTROL 23-46 ECOSMART CONNECT - ELECTRICAL DETAILS 47-48 ECOSMART CONNECT - CONSULTANTS SPECIFICATION 49 Doesn t cost the earth... nuaire.co.uk 19

ECOSMART CONNECT CONTROL (CO) FEATURES & BENEFITS QUICK & EASY TO INSTALL - A contros are pre-assembed, configured and instaed directy into the fan or air handing unit, this incudes two 4-port motorised vaves and actuators, pipework, off coi thermostats and interna sensors, frost protection, etc. Site time is kept to a minimum, quaity and efficiency maintained. EASILY ADJUSTABLE - No wasted energy or noise generation because the air voume can be precisey set via the LCD commissioning too or by a wa mounted LCD pane. SIMPLE, PRECISE COMMISSIONING - Ecosmart Connect enabes the system to be accuratey commissioned via an integrated speed contro, minimum and maximum speeds easiy adjusted via a remote LCD pane. QUIETER SYSTEM - With Ecosmart Connect your system is ony at maximum design duty when absoutey necessary. The noise eves within your systems are ower because the fans or air handing units are rarey at fu speed. IMPROVED LIFECYCLE - Ecosmart Connect enabes the fan or air handing unit to be run at ower speeds. This reduces the maximum oad and wear and therefore increases the overa working ife of the units. DEMAND VENTILATION - To achieve maximum potentia savings and the owest possibe energy consumption, combine Ecosmart Connect with sensors to ink the fan speed directy to demand. For exampe by using ESCO-CL or temperature sensors to contro fan speed when a room is occupied. HEALTHY ATMOSPHERE - Ecosmart Connect has a tricke function as standard which when activated, via a commissioning too which enabes you to set a background ventiation rate, keeping the rooms fresh when unoccupied, whist sti saving energy. System wi boost or ramp to maximum design duty when triggered by an Ecosmart or other externa device. PLUG IN CONTROLS - Simpe ow votage sensors compete with preassembed cabe means that any contro function is easiy achieved. You decide which conditions to monitor and the system wi operate at the optimum speed. No commissioning is required for these sensors. MULTIFUNCTION SENSORS - Ecosmart Connect sensors are avaiabe with mutipe sensor functions in one sma compact unit. Such as PIR and temperature, or 3 Speed Fan Override, temperature and setpoint adjust. ROOM TEMPERATURE CONTROL - The Ecosmart Connect contro strategy is set by defaut to reguate the suppy air temperature, but if a suitaby sized heater is fitted, the strategy can be modified to reguate the room air temperature instead. This aows Ecosmart Connect to be more efficient and economica at maintaining a constant room temperature. LCD PANEL - Ecosmart Connect is avaiabe with a remote LCD pane that can operate a network of Ecosmart Connect controers. It is BACnet compatibe and can read/write any BACnet variabes on the network. This aows the instaation of networks of Ecosmart Connect controers without the need of any extra compex components such as servers or network hubs. This is idea for singe instaations or sma networks aike. BACnet INTERFACE - Integrated BACnet features enabe any centra system to contro and monitor the fan or air handing unit via MS/TP (IP Ethernet optiona router avaiabe). This enabes monitoring of every BACnet variabe incuding individua room sensors. Variabes can aso be written aowing fu contro of the unit from a centraised remote ocation. BACKWARDS COMPATIBILITY - Athough Ecosmart Connect is equipped with a modern BACnet network interface, it sti comes as standard with switched ive inputs, vot free inputs, 0-10V inputs and vot free outputs for simper requirements. PEACE OF MIND - Ecosmart Connect has a 5 year warranty. ECOSMART CONNECT SUPPLY & EXTRACT VENTILATION SYSTEM CONNECTED TO ROOM MOUNTED SENSOR Room mounted Sensor 20 029 2085 8200 (MS/TP)

ECOSMART CONNECT CONTROL (CO) ROOM MODULES ESCO-TDFS Ecosmart Connect Room Modue - Temperature, Dispay and Fan Speed Override. ESCO-THPL Ecosmart Connect Room Modue - Temperature, Humidity and PIR. ESCO-TS Ecosmart Connect Room Modue - Temperature. ESCO-TDPL Ecosmart Connect Room Modue - Temperature, Dispay and PIR. ESCO-THS Ecosmart Connect Room Modue - Temperature and Humidity. ESCO-TDHPL Ecosmart Connect Room Modue - Temperature, Dispay, Humidity and PIR. ESCO-TDS Ecosmart Connect Room Modue - Temperature and Dispay. ESCO-TDHL Ecosmart Connect Room Modue - Temperature, Dispay and Humidity. ESCO-TDHS Ecosmart Connect Room Modue - Temperature, Dispay and Humidity. (Humidity is not dispayed). ESCO-PL Ecosmart Connect Room Modue - PIR Sensor. ESCO-TPL Ecosmart Connect Room Modue - Temperature and PIR. ESCO-CL Ecosmart Connect Room Modue - CO2 Sensor. Refer to page 22 for specifications and page 43 for sensor dimensions. ESCO-LCD TOUCH SCREEN DISPLAY The ESCO-LCD is a user friendy operator interface featuring BACnet communication and a coourfu, graphic dispay with touchscreen interface. It is powered by 12-24VAC / VDC. CODE DESCRIPTION - ROOM MODULES ESCO-TDHL 1 2 3456 1. Ecosmart 2. Connect 3. Temperature 4. Dispay 5. Humidity 6. L = Long ength S = Short ength nuaire.co.uk 21

SA BUS DEVICES - ROOM MODULES SPECIFICATIONS The foowing room modues are avaiabe. ECOSMART CONNECT CONTROL (CO) ROOM MODULES Group Nuaire Size Temp- Humidity LCD, PIR Fan Fan CO2 Network Notes Part (mm) erature Sensor Setpoint Speed Status Sensor Address Number Sensor Adjust & Override Dispay Range Occupancy Dispay Group 1 Max of 1 ESCO-TDFS 80x80 YES YES YES YES 199 Max of 1 Per (fixed) per Controer controer ESCO-TS 80x80 YES 200-203 ESCO-THS 80x80 YES YES 200-203 ESC-TDS 80x80 YES YES 200-203 ESCO-TDHS 80x80 YES YES YES 200-203 Reative Humidity is not dispayed ESCO-TPL 80x120 YES YES 200-203 Group 2 Max of 3 Per Controer ESCO-THPL 80x120 YES YES YES 200-203 ESCO-TDPL 80x120 YES YES YES 200-203 ESCO-TDHPL 80x120 YES YES YES YES 200-203 Reative Humidity is not dispayed ESCO-TDHL 80x120 YES YES YES 200-203 Reative Humidity is dispayed ESCO-PL 80x120 YES 200-203 ESCO-CL 80x120 YES 212-219 Powered via separate 24vac/ dc suppy 22 029 2085 8200

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY GENERAL The system incorporates a pre-configured MS/TP enabed controer. ROOM MODULES Ecosmart Connect aows the connection of mutipe Room Modues which are automaticay detected and connect to the controer via a SA (Sensor Actuator) MS/TP bus. See Network Accessory section for more connection detais. THE NUAIRE UNIT CONTAINS THE FOLLOWING CONTROLLABLE ITEMS: Inet Damper (if fitted). Exhaust Damper (if fitted). Heat Recovery and Bypass Damper. Heating Coi (if fitted). Cooing Coi (if fitted). Suppy Fan Speed. Extract Fan Speed. ENABLE SIGNAL The unit can be enabed via the foowing methods: Software switch (ENABLE) via oca dispay or network. Switched ive (230VAC) input, PIR etc. Vot free input contacts. Night cooing / summer free-cooing strategy. Schedued via weeky caendar. (Schedue are accessed and adjusted via the ESCO-LCD) Fan Speed Override Room Modue PIR sensor Room Modue 3-Fan Speed Button (Whie in ow, med or high state) ROOM MODULE PIR When a Room Modue PIR sensor is connected via the SA bus, the contro wi automaticay use this as an enabe signa by defaut. There is a non-adjustabe minimum run-on time of 15mins for Room Modue PIRs. This is in addition to any software run-on times. RM 3-SPEED FAN OVERRIDE (ESCO-TDFS ONLY) When a RM fan speed override is avaiabe it wi override fan speed functions. This function overrides any run-on time (except for eectric heater heat dissipation). Whie in override mode, the unit wi ignore return air temperature and set the suppy air to the setpoint. Mutipe fan override sensors are not supported. Whenever a fan-speed override Room Modue is connected, the dispay wi automaticay show the fan speed status at a times. Warning: If a RM Fan Speed override button is eft in any position (apart from auto), the unit wi stay in override mode indefinitey. This incudes off mode. Mode Operation Dispay Auto The controer wi ignore the fan speed override. Current fan speed wi sti be dispayed. When the enabe signa is removed, the unit wi run on for a time defined by the run-on setpoint. If auto run-on is enabed, the unit wi measure the each enabe period and set a dynamic run-on time proportionay to this vaue. This time is scaed by the network input Auto run-on Scae Factor and imited by the input Auto Run-on Max Time. Off Low The controer wi override a functions and stop the fans. The fans run at ow speed. Medium The fans run at medium speed. High The fans run at high speed. (MS/TP) nuaire.co.uk 23

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY RM OCCUPANCY DISPLAY If an RM sensor with occupancy dispay is connected, it wi automaticay dispay the occupancy state as foows. State Description RM Dispay Occupied An enabe signa is present i.e. Fans are running. Unoccupied No enabe & no tricke. i.e. Fans are stopped. Standby No enabe signa but fans are tricking MULTIPLE SENSORS Where mutipe sensors are connected the foowing options are avaiabe. Function Description Avaiabe Ranges 0-10V 0-10V is scaed as defined by 0 to 50 C Temperature the network input 0 to 40 C Sensor Temperature Sensor 0 to 100 C 0-10V Output Range 0 to 80 C 0 to 90 C 0-10V Pressure 0-10V is scaed as defined by 0-25Pa Sensor the network input 0-50Pa Pressure Sensor 0-100Pa 0-300Pa 0-500Pa 0-1000Pa 0-1600Pa 0-2500Pa 0-3000Pa 0-10V 0-10V is scaed to 0-100% Humidity humidity 0-100% ony Sensor Network Input Name Temp Sensor Operation Setpoint Operation Humidity Sensor Operation CO2 Sensor Operation Pressure Sensor Operation Options Room modue average (Defaut) Return Air ony Room Modue & Return Air Average Last Vaue Changed (Defaut) Software Setpoint Ony (ignore room modue) Average (Defaut) Max Ignore Average (Defaut) Max Ignore Average (Defaut) Max Ignore FAN SPEED CONTROL INPUT Once assigned to either input 4 or 5, the 0-10V input is scaed to 0-100% fan speed demand. ECOSMART GATEWAY GADGET (EGG) If an EGG PCB is instaed on the system this wi give an enabe signa and aso a 0-10V fan speed demand. The EGG aows an existing NET sensor network to give a fan speed demand to a controer. CO 2 CONTROL When a CO 2 sensor is assigned to the system and an enabe signa is received, ventiation wi increase fans speeds to reduce CO 2 concentration. The target CO 2 sensor setpoint can be changed as one of the commissioning setpoints. Room Modue CO 2 sensors are detected automaticay. 0-10V CO 2 sensors need to be assigned to input 4 or 5. AUXILIARY INPUTS 4 & 5 (0-10V INPUTS) The function of IN4 & IN5 can be set by the network inputs IN4 Function & IN5 Function. The avaiabe options are as foows. Function Description Avaiabe Ranges None The signa is ignored N/A Fan Speed A 0-10V input is used as a Contro fan speed demand. N/A 0V = Min Speed 10V = Max speed EGG (Ecosmart 0-10V from the EGG PCB is Gateway Contro used as a fan speed N/A Gadget) demand. The optiona EGG PCB can be used for backwards compatibiity with some Ecosmart Cassic sensors. 0-10V CO2 0-10V is scaed as defined 0-2,000ppm Sensor by the network input 0-4,000ppm CO2 0-10V Output Range 0-5,000ppm 0-10,000ppm 0-20,000ppm HUMIDITY CONTROL When a humidity sensor is assigned to the system and an enabe signa is received, ventiation wi increase fans speed to reduce humidity. The target humidity setpoint setpoint can be changed as one of the commissioning setpoints. Room Modue humidity sensors are detected automaticay. 0-10V humidity sensors need to be assigned to input 4 or 5. CONSTANT PRESSURE CONTROL When a pressure sensor is assigned to the system and an enabe signa is received, ventiation wi increase fans speeds to increase pressure to the target setpoint. The target pressure setpoint can be changed as one of the commissioning setpoints. 0-10V pressure sensors need to be assigned to input 4 or 5. Room Modue pressure sensors are not avaiabe. 24 029 2085 8200 (MS/TP)

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY CONFIGURABLE MODE (VIA SWITCHED LIVE 2) The switched ive 2 input is a configurabe input that can be set to perform a number of functions. The function is set via the network input Configurabe Mode SL2. These functions wi incude the foowing: Fan Boost (Defaut Setting) This enabes Fan Boost mode Heater Boost The heater function wi be enabed. Fan speeds wi be increased where necessary to keep suppy temp at the heater boost setpoint. (Defaut 35 C). FAN BOOST When the contro receives a boost signa, from either the network input Boost or Configurabe SL2 configured to boost the fans wi run at boost speed. Once the signa is removed the fans wi run on for a time defined by the boost run-on setpoint. HEAT BOOST When the contro receives a heat boost signa, from either the network input Heat Boost or Configurabe SL2 configured to heat boost, the heater output wi increase to 100%. The fan speed wi be increased as required to reach the heat boost setpoint. TEMPERATURE CONTROL SUPPLY TEMPERATURE CONTROL (DEFAULT) Whie an enabe signa is present, this mode moduates heating, cooing & heat exchanger bypass dampers with the aim of the suppy air reaching the temperature setpoint. Pease note that heating and cooing outputs wi ony function if the Heating Type or Cooing Type network inputs are set to heating or cooing options. Room Air Temp Suppy Set Point HX Bypass HX The heat exchange bypass damper operates by cacuating the suppy air temperature based on the return air temperature, the outside air temperature and the heat exchanger efficiency. (Eg. A 13 C outside air temperature with a 23 C return air temperature wi give a suppy air temperature of 20.5 C). The contro then chooses the damper position which requires the minima heat/coo tempering in order to achieve the setpoint. Bypass Outside Air Temp. Note that the white areas indicate regions where either heat exchanging or bypassing wi achieve the same suppy temperature. ROOM TEMPERATURE CONTROL Whie an enabe signa is present, this mode moduates heating, cooing & heat exchanger bypass dampers with the aim of the room air reaching the temperature setpoint. Pease note that heating and cooing outputs wi ony function if the Heating Type or Cooing Type network inputs are set to heating or cooing options. When heating or cooing is required achieve the room setpoint, the output of the heat/coo oops are spit between ventiation demand or heat/coo demand according to the foowing graphs. The intermediate boost zone is the area in which a sma amount of free-heat/cooing is avaiabe. In this zone, heating/cooing is used to boost the free-heating/cooing. In room temperature contro mode, the bypass damper is controed according to the foowing chart. A minimum suppy air temperature imit is incuded to stop the heat exchanger being bypassed when the air temp is uncomfortaby cod, even though cooing is required. In this case the heat exchanger wi temper the air for comfort. The reverse appies for the maximum suppy air temperature imit. If the suppy air temperature exits the min-max suppy temperature range, the unit wi adjust ventiation, heating or cooing to compensate. Note: Room temperature contro wi ony be effective if the heater unit is sized correcty for the space. If the unit is undersized, heating from an externa source may be required. Boost Band Room Air Temp Heating Heat Boost Zone Free Heating Vent Ony Room Air Temp Free Cooing Vent Ony Coo Boost Zone Cooing Room Air Temp Room Set Point HX Bypass Bypass HX Deadband Boost Band Outside Air Temp Outside Air Temp Min Suppy Outside Max Suppy Air Temp. Air Temp. Air Temp. nuaire.co.uk 25

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY OVERRIDES When the foowing conditions occur, the system wi temporariy exit Room Temperature Mode and enter Suppy Temperature Mode. Tricke Mode with no enabe signa. (Tricke deadband appies) Heat Boost Active Fan Boost Active Purge Mode Active 3-Speed override by Room Modue TRICKLE MODE When tricke mode is active, the fans wi run at their minimum speed even when there is no enabe signa. Heating and cooing wi aso function in this mode if avaiabe. Whie in tricke mode, the unit wi function in Suppy Temperature Contro Mode but with a different, wider deadband, set by the network input Tricke Deadband. FROST PROTECTION Shoud the interna temperature of the unit fa beow a vaue defined in the commissioning variabes, the contro wi override a heating/cooing ogic to open the LPHW or CW contro vaves, if fitted. This is to aow any protective fow through the heating/cooing cois. The suppy fan wi aso stop and the appropriate frost protection software modue wi enter an aarm state. This period wi ast for a minimum of 5 minutes by defaut. The faut reay wi aso open. Heat and coo demand reays wi operate and the software frost aarm wi enter an aarm state. Pease note that frost protection wi ony function if the Heating Type or CooingType setpoints are set to LPHW or CW. NIGHT COOLING / SUMMER FREE COOLING Once enabed in software, this routine uses an individua time schedue to coo the fabric of the buiding at night using ony the externa air. This mode ony functions if the daytime temperature is above the setpoint, cooing is possibe and if the cooing air is not too cod. ALARMS CRITICAL ALARM LATCHING Once in critica aarm state the unit wi drive a heating and cooing outputs to 0V. In the event of fan fai other functions continue as norma. The critica aarm is atched and required manua reset or power cyce to cear. Causes of critica aarm: Fan fai via faut circuit 1 Heater overtemp via faut circuit 1 MAINTENANCE ALARMS (NON-LATCHING) Once in maintenance aarm state the ony action taken is de-energising of the faut reay. Once the trigger is removed, the aarm wi reset automaticay. Causes of maintenance aarm: Condensate pump faut (This bypasses the heater exchanger automaticay) Sensor Faiure Low suppy temperature, defaut 8 C. This can be set to stop fans if required Frost protection routine active, defaut 4 C (This ony runs if water vaves are seected as fitted) Excessivey high suppy temperature reading (this wi stop heating) Fiter dp faut (if fitted) A aarms have a hod off period set by the setpoint Aarm Deay. THERMAL TRIP In case of software faiure, as a fina resort, the eectric heater is protected by a fai-safe therma overoad switch. This switch disabes the heater controer once the temperature reaches 80 C. When this occurs, the critica aarm wi atch in software. Once the unit coos, the contactor wi re-engage but the heater signa wi remain at 0V unti the critica faut is reset in software or by power cyce. PURGE MODE Once enabed in software, this routine uses an individua time schedue to provide a period of increased air change throughout a space. This mode ony functions if the inet air is above a minimum temperature of 12 C. Whie purge is in progress, the unit wi function in Suppy Temperature Contro Mode but with a different, wider deadband, set by the network input Tricke Deadband. HIBERNATE This mode is avaiabe for LPHW and CW units where the vaves are required to be driven open in anticipation of a period where the unit is eectricay isoated and inactive. When enabed via the network input Hibernate Mode this wi stop the fans and open a LPHW & CW vaves fuy. The unit can then be powered down. This mode activation is reset upon power cyce so when restarted the unit wi function as norma. This mode is for periods when to buiding is eft dormant and wi stop the cois trapping water and causing a freeze risk. It wi be the buidings responsibiity to provide freeze-preventative heating during this time. This can aso be used for a ceaning or fushing cyce. 26 029 2085 8200

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY EXPOSED BACNET OBJECT LIST (BY CATEGORY) ENABLE LCD Browser BACnet Object Description Object Object ID Defaut Vaue Units Page Type 32 Enabe Software enabe switch MSV 10218 Off Off/On 19 SL Enabe The state of the enabe input BI 10161 N/A Off/On 10 Run-on (Enabe) Run-on timer vaue AV 10267 0 Seconds 25 Time Schedue Loca Time Schedue SCH 10496 N/A N/A 32 Enabe via Schedue Enabed via Schedue MSV 10219 N/A Off/On TRICKLE MODE 35 Tricke Mode Enabe tricke mode MSV 1 0250 Off Off/On 16 Tricke Deadband Tricke mode deadband AV 10316 5 Degrees-Cesius IO DAMPERS 13 IO Damper Deay Deay between starting the fan AV 10279 0 Seconds reay and the fan output. ANALOGUE INPUTS 2 IN4 The 0-10 votage at input 4 AI 10032 N/A Vots 29 IN4 Function Function of the UI4 input MSV 10209 None None Fan Speed Contro EGG 0-10V CO2 Sensor 0-10V Temperature Sensor 0-10V Humidity Sensor 0-10V Pressure Sensor 2 IN5 The 0-10 votage at input 5 AI 10035 N/A Vots 30 IN5 Function Function of the UI5 input MSV 10210 None None Fan Speed Contro EGG 0-10V CO2 Sensor 0-10V Temperature Sensor 0-10V Humidity Sensor 0-10V Pressure Sensor CONFIGURABLE INPUTS 19 SL2 Input The state of the configurabe input (IN9) BI 10164 N/A Off/On 28 SL2 Mode Set the function of switched ive 2 MSV 10202 Fan Boost None/Fan Boost/Heater Boost FAN BOOST 32 Fan Boost Software enabed Fan boost MSV 10240 Off Off/On 11 Run-on (Boost) Boost run-on time AV 10272 0 Seconds 11 Fan Boost Speed Fan boost speed AV 10273 100 Per cent HEAT BOOST 28 Heat Boost Software enabed Heater boost MSV 10205 Off Off/On 12 Heat Boost Setpoint Setpoint Heater Boost Setpoint AV 10276 35 Degrees-Cesius FAN OUTPUTS 7 Suppy Fan Output The 0-10V signa to the suppy fan AO 10182 N/A Vots 7 Extract Fan Output The 0-10V signa to the extract fan AO 10176 N/A Vots 20 Fan Enabed Cmd The state of the fan enabed reay BO 10191 N/A Off/On (MS/TP) nuaire.co.uk 27

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY EXPOSED BACNET OBJECT LIST (BY CATEGORY) FAN COMMISSIONING LCD Browser BACnet Object Description Object Object ID Defaut Vaue Units Page Type 10 Extract Fan Max Individua fan maximum speed setting AV 10268 100 Percent 11 Extract Fan Min Individua fan minimum speed setting AV 10270 20 Percent 16 Suppy Fan Max Individua fan maximum speed setting AV 10312 100 Percent 16 Suppy Fan Min Individua fan minimum speed setting AV 10314 20 Percent TEMPERATURE CONTROL 15 Software Setpoint Software Setpoint AV 10309 22 Degrees-Cesius 10 Deadband Deadband for temp contro AV 10266 3 Degrees-Cesius 31 SetPoint Op Setpoint operation MSV 10214 Last Vaue Chg Last Vaue Changed /Software Ony 31 T Sens. Op Temperature sensor operation MSV 10215 NS Average NS Average/Return Air Ony/ NS & Return Average 31 0-10V Temp Range Temperature sensor range MSV 10216 0 to 50 C 0 to 50 C/0 to 40 C/ 0 to 100 C/0 to 80 C/ 0 to 90 C 33 Temp Contro Mode Temperature contro mode STC/RTC MSV 10245 ReturnTempCtr Suppy Temperature Ctr/ Return Temperature Ctr 15 STC H/C Pref STC Heat/Coo Pref AV 10310 50 No units 16 STC HX Efficiency STC HX Efficiency AV 10311 0.8 No units 14 RTC Boost Band Return Temperature Contro Boost Band AV 10306 15 Degrees-Cesius 15 RTC Max Suppy Temp Max suppy temp when in RTC mode AV 10307 35 Degrees-Cesius 15 RTC Min Suppy Temp Min suppy temp when in RTC mode AV 10308 12 Degrees-Cesius HEATING OUTPUT 29 Heating Type Set the type of heating fitted MSV 10206 As per buid None/LPHW/Eectric 7 Heating Output The 0-10V signa to the heating output AO 10179 N/A Percent 21 Heating Demand Cmd The state of the heating demand reay BO 10197 N/A Off/On COOLING OUTPUT 28 Cooing Type Set the type of cooing fitted MSV 10203 None None/Cod Water/DX 7 Cooing Output The 0-10V signa to the cooing output AO 10173 N/A Percent 20 Cooing Demand Cmd The state of the cooing demand reay BO 10194 N/A Off/On HX BYPASS DAMPER 20 Bypass Damper Cmd The signa to the bypass damper BO 10185 N/A Open/Cose (Cose = Bypass) 28 029 2085 8200

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY EXPOSED BACNET OBJECT LIST (BY CATEGORY) FAN DEMANDS INPUTS LCD Browser BACnet Object Description Object Object ID Defaut Vaue Units Page Type 10 CO2 Target Target CO2 Vaue AV 10265 650 Parts-Per-Miion 27 0-10V CO2 Range CO2 sensor output range MSV 10200 0-2,000ppm 0-2,000ppm/0-4,000ppm/ 0-5,000ppm/0-10,000ppm/ 0-20,000ppm 27 CO2 Sensor Op CO2 sensor operation in case of MSV 10201 Average CO2/MaxCO2/ mutipe sensors Ignore CO2 12 Humidity Target Reative HumidityTarget AV 10278 60 Percent-reative-Humidity 29 Humidity Sensor Op Humidity Sensor Operation in case MSV 10207 Average RH% Average RH%/Max of muipe sensors RH%/Ignore RH% 14 Pressure Target Target pressure vaue AV 10303 400 Pascas 30 0-10V Press Range Pressure sensor range MSV 10212 0 to1000pa 0-25Pa/0-50Pa/0-100Pa /0-300Pa/0-500Pa/0-1000Pa /0-1600Pa/0-2500Pa/ 0-3000Pa 30 P sens. Op Pressure sensor operation in case of MSV 10213 Average Vaue Average Vaue/ mutipe sensors Max Vaue SELECTED PROCESS VARIABLES 17 Room Air Temp The room air temperature AV 11296 N/A Degrees- Cesius 17 CO2 Leve The CO2 Leve AV 13980 N/A ppm 17 Humidity The Humidity Leve AV 14297 N/A % RH 17 Active Setpoint The setpoint currenty used AV 14534 N/A Degrees-Cesius XBC TEMPERATURE SENSORS 1 Suppy Air Temp (B) The suppy air temperature AI 10005 N/A Degrees-Cesius 1 Fresh Air Temp (H) The fresh air temperature AI 10008 N/A Degrees-Cesius 1 Extract Air Temp (C) The extract air temperature AI 10011 N/A Degrees-Cesius ZONE SENSORS 2 RM199 Temp The temperature at RM address 199 AI 10029 N/A Degrees-Cesius 2 RM199 Humidity The Humidity at RM address 199 AI 10017 N/A Percent-Reative-Humidity 8 RM199 Setpoint The setpoint at RM address 199 AV 10023 N/A Degrees-Cesius 26 RM199 Fan Speed Fan Speed Override Status of RM199 MSV 10014 N/A Off/Auto/Low/Medium/HIgh 35 RM199 Fan Dispay Fan Speed Override Dispay at MSV 14703 N/A No Status/Off/Low/Medium RM address 199 /High/Auto-Off/Auto-Low /Auto-Medium/Auto-High 3 RM200 Temp The temperature at RM address 200 AI 10050 N/A Degrees-Cesius 3 RM200 Humidity The Humidity at RM address 200 AI 10053 N/A Percent-Reative-Humidity 8 RM200 Setpoint The set point at RM address 200 AV 10074 N/A Degrees-Cesius 3 RM201 Temp The temperature at RM address 201 AI 10065 N/A Degrees-Cesius 4 RM201 Humidity The Humidity at RM address 201 AI 10077 N/A Percent-Reative-Humidity 8 RM201 Setpoint The setpoint at RM address 201 AV 10083 N/A Degrees-Cesius 3 RM202 Temp The temperature at RM address 202 AI 10068 N/A Degrees-Cesius 4 RM202 Humidity The Humidity at RM address 202 AI 10092 N/A Percent-Reative-Humidity 8 RM202 Setpoint The setpoint at RM address 202 AV 10098 N/A Degrees-Cesius (MS/TP) nuaire.co.uk 29

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY EXPOSED BACNET OBJECT LIST (BY CATEGORY) ZONE SENSORS (Continued from previous page) LCD Browser BACnet Object Description Object Object ID Defaut Vaue Units Page Type 4 RM203 Temp The temperature at RM address 203 AI 10071 N/A Degrees-Cesius 4 RM203 Humidity The Humidity at RM address 203 AI 10107 N/A Percent-Reative-Humidity 9 RM203 Setpoint The setpoint at RM address 203 AV 10113 N/A Degrees-Cesius 5 RM212 CO2 The CO2 at RM address 212 AI 10137 N/A Parts-Per-Miion 6 RM212 Temp The temperature at RM address 212 AI 10149 N/A Degrees-Cesius 5 RM213 CO2 The CO2 at RM address 213 AI 10140 N/A Parts-Per-Miion 6 RM213 Temp The temperature at RM address 213 AI 10152 N/A Degrees-Cesius 5 RM214 CO2 The CO2 at RM address 214 AI 10143 N/A Parts-Per-Miion 6 RM214 Temp The temperature at RM address 214 AI 10155 N/A Degrees-Cesius 5 RM215 CO2 The CO2 at RM address 215 AI 10146 N/A Parts-Per-Miion 6 RM215 Temp The temperature at RM address 215 AI 10158 N/A Degrees-Cesius FROST PROTECTION 11 Frost Prot. Fan Off Minimum time the suppy fan wi stop AV 10274 300 Seconds in a frost protection state 12 Frost Prot.Temp Suppy temperature at which frost AV 10275 4 Degrees-Cesius protection becomes active HIBERNATE 32 Hibernate Mode Unit is ready for hibernation. MSV 10241 Off Off/On Resets on powercyce PURGE MODE 33 Purge Active This input wi enabe purge mode MSV 10243 Off Off/On 14 Purge Fan Speed Purge Fan Speed AV 10304 60 Percent 14 Purge Min Temp The minimum temperature that AV 10305 12 Degrees-Cesius wi stop puge mode 25 Purge Time Schedue Purge Time Schedue SCH 10499 N/A N/A 35 Purge via Schedue Purge Time Schedue State MSV 10512 N/A Off/On NIGHT COOL MODE 33 Night C Mode This input wi enabe night coo mode MSV 10242 Off Off/On 13 Night C Fan Speed The night coo fan speed AV 10281 60 Percent 13 Night C Min Temp The minimum temperature that wi AV 10302 12 Degrees-Cesius stop night cooing 25 Night C Schedue Night Cooing Schedue SCH 16014 N/A N/A 36 Night C Schedue Night Coo Schedue State MSV 16014 N/A Off/On 25 Night C Sampe Daytime schedue for winter or SCH 15875 N/A N/A summer decision making 36 Night C Sampe Night Coo Samping Schedue State MSV 16008 N/A Off/On AUTO RUN-ON 31 Auto Run-on Auto run-on mode MSV 10217 Off Off/On 9 Auto-Run-on Maximum Run-on Max Time AV 10263 900 Seconds Max Time 9 Auto-Run-on Scae Factor for automatic run-on time AV 10264 2 No Units Scae Factor 30 029 2085 8200 (MS/TP)

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY EXPOSED BACNET OBJECT LIST (BY CATEGORY) ALARM LCD Browser BACnet Object Description Object Object ID Defaut Vaue Units Page Type 20 Faut Reay Cmd The state of the faut reay BO 10188 N/A Aarm/Norma (Faut = De-energised) 9 Aarm Deay Aarm hod off period AV 10262 10 Seconds 22 Reset Aarms Changing this vaue wi reset any BV 10332 FALSE True/Fase atched aarms 19 Aarm Circuit 1 The state of Aarm Circuit 1 BI 10167 N/A Norma/Aarm 19 Aarm Circuit 2 The state of Aarm Circuit 2 BI 10170 N/A Norma/Aarm 12 High Temp Aarm Suppy temp which wi trip the AV 10277 50 Degrees-Cesius high suppy aarm 13 Low Temp Aarm Suppy temp which wi trip the AV 10280 8 Degrees-Cesius ow suppy aarm 30 Low Temp Action Action taken when the ow suppy MSV 10211 Aarm Ony Aarm ony / Aarm and aarm is engaged stop fans 35 Critica Aarm Unit is atched in critica aarm MSV 15309 N/A Norma/Aarm 36 Maint. Aarm Maintenance Aarm MSV 15310 N/A Norma/Aarm 36 XBC Sensor Aarm XBC Sensor Out of Range MSV 17009 N/A Norma/Aarm 37 Low SA-T Aarm Low Suppy Air Aarm MSV 17011 N/A Norma/Aarm 37 High SA-T Aarm High Suppy Air Aarm MSV 17012 N/A Norma/Aarm 37 Frost Aarm The unit is in frost mode MSV 17013 N/A Norma/Aarm LCD EVENT SIGNAL 37 Aa(A Circ 1) For LCD Event Signa ony MSV 17281 N/A Norma/Aarm 38 Nor(A Circ 1) For LCD Event Signa ony MSV 17282 N/A Norma/Aarm 38 Aa(Low Suppy Temp) For LCD Event Signa ony MSV 17285 N/A Norma/Aarm 38 Nor(Low Suppy Temp) For LCD Event Signa ony MSV 17286 N/A Norma/Aarm 38 Nor(High Suppy Temp) For LCD Event Signa ony MSV 17289 N/A Norma/Aarm 39 Aa(High Suppy Temp) For LCD Event Signa ony MSV 17290 N/A Norma/Aarm 39 Aa(A Circ 2) For LCD Event Signa ony MSV 17293 N/A Norma/Aarm 39 Nor(A Circ 2) For LCD Event Signa ony MSV 17294 N/A Norma/Aarm 39 Aa(Frost) For LCD Event Signa ony MSV 17316 N/A Norma/Aarm 40 Nor(Frost) For LCD Event Signa ony MSV 17317 N/A Norma/Aarm 40 Aa(XBC Sensor) For LCD Event Signa ony MSV 17320 N/A Norma/Aarm 40 Nor(XBC Sensor) For LCD Event Signa ony MSV 17321 N/A Norma/Aarm FACTORY SETTINGS 28 Damper Override Override bypass damper position MSV 10204 Auto Auto/Heat Exchange/Bypass 33 Tacho PCB Fitted Is a Taco Be PCB fitted MSV 10244 As per buid Yes/No 22 Tuning Reset Resets the PID auto tuning oops BV 12880 FALSE True/Fase 29 Ignore PIR Sensors Ignore a MSTP network PIR sensors MSV 10208 No Yes/No 18 EF Max Vot The upper votage for the extract fan AV 17273 10 vots 18 EF Start Vot The votage required to start the AV 17274 1 vots extract fan 18 SF Max Vot The upper votage for the suppy fan AV 17275 10 vots 18 SF Start Vot The votage required to start AV 17276 1 vots the extract fan 40 SW-FAC2612-2-4A Strategy Version MSV 17340 Off Off/On nuaire.co.uk 31

NETWORK CONNECTION DIAGRAM ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY Ethernet IP MSTP to IP Router (Fied Controer) FC bus (Sensor Actuator) SA bus (Sensor Actuator) SA bus For best resuts, use a inear network and switch on the EOL resistors at each end of the FC bus. 32 029 2085 8200

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY FAC CONTROLLER A FAC controer is used to contro the unit. The controer can connect to the FC bus via the 4 pin FC connection. BACNET IP TO MS/TP ROUTER (ESCO-IPN) The BACnet IP to MS/TP Router exchanges information between networks and aows the controer to communicate on an IP network. One router is required for each MS/TP network. MAC Address The physica MAC address of the FAC adjustabe between 4-127 and is set via the DIP switch on the front of the unit. When mutipe controers are connected on the same FC bus, each controer s MAC address must be unique. BACnet Instance Number The BACnet instance number of the FAC is factory-set to a random unique vaue from 0-4,194,304. This ensures that every controer wi have a unique BACnet instance number on any possibe network. End Of Line (EOL) Resistor When an FAC controer is used as a terminator at the end of a FC bus ine, the EOL resistor dip switch can be switched on for best performance. Faut Light Status Bink 5Hz - Not a possibe room modues are connected. This is norma. Bink 2Hz - Startup in progress Off Steady - No Fauts On Steady - No Software The BACnet router has a USB 2.0, Type B receptace which is ony used to obtain power from a computer or USB adapter. A mains adapter and cabe is suppied. The router connects to the FC bus via screwed terminas. Address Type Defaut Address IP Address 192.168.92.68 Subnet Mask 255.255.255.0 (/24) A reset switch is avaiabe inside a sma hoe ocated on the side of the case. If you press the reset switch with a paper cip (or simiar device) for at east 1 second, the switch resets to the defaut vaues of the IP address, gateway address, and netmask. After you use the reset switch, you need to reboot the router. The BACnet/IP to MS/TP Router contains a Web server. You can access the Web server from any Internet-compatibe computer on the oca network To configure the router, you need a computer with an Ethernet connection, router, and standard Web browser. INTERCONNECTION The FC bus connects via the foowing MSTP cabing: ESCO-MSTPC30M Ecosmart Connect MSTP cabe ree 30m ESCO-MSTPC150M Ecosmart Connect MSTP cabe ree 150m Suggested Wiring Coouring White + Green - Back COM Red Unused Note: On the SA Bus, the + and - wire are one twisted pair, and the COM and SA PWR are the second twisted pair of wires. These cannot be used with RJ12 connections and must be stripped and connected using screwed terminas. The shied must be earthed at the contro pane end ony and be made continuous aong the bus ength. Room Modues must not be fitted more than 150metres (cabe ength) from the controer. (MS/TP) nuaire.co.uk 33

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY TOUCH SCREEN (ESCO-LCD) FIELD ADVANCED DISPLAY (FAD) The ESCO-LCD is a user friendy operator interface featuring BACnet communication and a coourfu, graphic dispay with touch-screen interface. It is powered by 12-24VAC / VDC and connected via the FC bus. NAVIGATION Cance Quit and moves to the previous section Home Shortcut to the configured Home Page Back Moves to the previous page in the same section Forward Moves to the next page in the same section Network Settings Device Name FAD0351 Device ID 127 MAC Address 127 Descriptions Fied Advanced Dispay Baud Rate 38400 Max Info Frames 4 TL-BRTRP-0 0 1 Nuaire XBC ESC 4 0909501 Nuaire XBC ESC 5 0909502 Enter Appies changes Settings Network Favourites Target Enabe Off MSV10218 Setpoint 22 C AV 10309 Heat Boost Off MSV10205 Fan Boost Off MSV10240 Temperature 22.2 o C 34 029 2085 8200

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY QUICK SETUP The foowing section expains how to quicky set-up the FAD with a target object and some favourites. SETTING UP A TARGET OBJECT Target objects aow the user to view a target device and object within the entire network. To choose a target object Navigate to the settings page. Seect the right arrow four times to reach the Seect Target Device screen. Enter the physica MAC address* of the controer (Device names or BACnetIDs can aso be used but MAC addresses are shorter) Seect the right arrow once Enter the object type of the required object (Eg AI, AO, MSV)** Enter the BACnet ID** of the object. (0-4194304) Seect the home icon. Seect Target Device Device Name Mac Address 4 Device ID 0 Seect Target Device Object Type AI Object ID 10050 * This is the setting of the DIP switch on the front of the FAC controer. This can aso be discovered by browsing to the network screen whie ID is seected in the View Config settings screen. MAC Address Name Description Status Function Write ID TL-BRTRP-0 0 1 Nuaire XBC ESC 4 0909501 Nuaire XBC ESC 5 0909502 BACnet Device ID ** Popuar object detais are isted beow, or use the network browser or see Exposed BACnet Object List for a fu ist. Network Page Description Object Type Object ID 17 Room Air Temp AV 11296 17 CO2 Leve AV 13980 17 Humidity AV 14297 17 Active Setpoint AV 14534 1 Fresh Air Temperature AI 10008 (MS/TP) nuaire.co.uk 35

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY SETTING UP A TARGET OBJECT CONT. To set the target object page as the defaut home page. Navigate to the settings page. Seect the right arrow twice to reach the dispay settings screen. Seect Home Page Seect Target Seect the enter icon Seect the home icon Note: The BACnet type & ID wi be dispayed on the target page if ID is seected on the View Config settings screen. Dispay Settings Backight Stand-By-OFF Home Page Target Service Password 0 User Password 0 Stand By Dark Stand By Timer 0 Note: If the target page is seected as the home page and a security password is set the home page wi be ocked. The ony way to exit the target screen in this case is to press the Nuaire ogo to the top right of the screen for 5 seconds. SETTING UP FAVOURITES The Favourite screen dispays a ist of favourite objects. To add or remove favourites. Navigate to the settings page Seect the right arrow six times to reach the View Config screen. Seect the function tickbox and favourite star. Seect the home icon Navigate to the network page. Seect the appropriate controer Navigate to the required object. See Exposed BACnet Object List for a fu ist. (Pressing for 3 seconds on an object wi dispay the fu name.) Seect the star to turn it back Navigate and seect any other required favourites When finished, navigate back to the View Config screen in the settings section and remove the function tick View Config Name Description Status Function Write ID Favourites can be removed by browsing the favourites page, seecting an object and then seecting the trashcan. Favourites can be re-ordered by upoading the favourite settings to a usb memory stick and changing the order of the items in the favourites.csv fie. This fie can then be downoaded back to the LCD. Enabe Fan Boost Heat Boost Tricke Mode On Off Off Off Network Page Description Object Type Object ID 17 Room Air Temp AV 11296 17 CO2 Leve AV 13980 17 Humidity AV 14297 17 Active Setpoint AV 14534 32 Enabe MSV 10218 25 Time Schedue SCH 10496 32 Fan Boost MSV 10240 28 Heat Boost MSV 10205 1 Fresh Air Temperature AI 10008 15 Software Setpoint AV 10309 36 029 2085 8200 (MS/TP)

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY SETTING UP SECURITY Note: If the target page or favourite page is seected as the home page and a security password is set, the home page wi be ocked. The ony way to exit the target screen in this case is to press the Nuaire ogo to the top right of the screen for 5 seconds. A security password wi then be requested to access the main menu. The security password timeout is the same as the standby timer and set via the dispay settings. TO SET A USER PASSWORD Navigate to the settings page Seect the right arrow twice to reach the dispay settings screen Change the user password a 4 digit number The user password wi now be requested each time a ocked object is written The user password is aso needed to exit the target page. (When the home page is set to target) Dispay Settings Backight Stand-By-OFF Home Page Target Service Password 0 User Password 0 Stand By Dark Stand By Timer 0 TO SET A SERVICE PASSWORD Navigate to the settings page Seect the right arrow twice to reach the dispay settings screen Change the service password a 4 digit number The service password wi now be requested each time the settings page is accessed Dispay Settings Backight Stand-By-OFF Home Page Target Service Password 0 User Password 0 Stand By Dark Stand By Timer 0 TO DISABLE WRITING OF VALUES Navigate to the settings page Seect the right arrow six times to reach the View Config screen De-seect the write tickbox. A controer points are now read ony A service password wi need to be set to stop users re-enabing the write function View Config Name Description Status Function Write ID TO ALLOW BASIC VALUES TO BE WRITTEN BY THE USER Navigate to the settings page Seect the right arrow six times to reach the View Config screen Seect the function tickbox and ock Seect the home icon Navigate to the network page. Seect the appropriate controer. Navigate to the required object. See Exposed BACnet Object List for a fu ist. Seect any vaues that need password protection. A back ock indicates a ocked vaue When finished, navigate back to the View Config screen in the settings section. Remove the Function tick and enabe writing of vaues A user password wi need to be set to stop writing of ocked vaues. It is recommended that a vaues are ocked except the foowing; Network Page Description Object Type Object ID 32 Enabe MSV 10218 25 Time Schedue SCH 10496 32 Fan Boost MSV 10240 28 Heat Boost MSV 10205 15 Software Setpoint AV 10309 View Config Name Description Status Function Write ID NS Zone Temp 0 C NS Zone 1 Temp 0 C NS Zone 2 Temp 0 C NS Zone 3 Temp 0 C nuaire.co.uk 37

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY SCHEDULING PAGE Standard BACnet schedue objects can be adjusted in the same way as any other BACnet object. The BACnet schedue function consists of an array of singuar time vaues with a corresponding ON/OFF state. In order to end an ON period, a new vaue must be created with a vaue of OFF. This new vaue s time can be adjusted to the desired end time. Time Schedue **-**-** **-**-** Effective Period ** Denotes A. Weeky Schedue. Seect a schedue object via object browser or the favourites menu to access the foowing screens. Seected Day. Time Schedue 10-10-15 15.39 Add Period. OFF ON OFF ON Seected Period Remove Seected Period. Seected Period s Time & State. Save Change. ALARM LOG When an XBC aarm changes state, a signa is sent to the LCD dispay and ogged on the aarm page. If there are items on the aarm page the standard top eft page icons change to one of the foowing, depending on the current page. The aarm page can be accessed by seecting the aarm icon. Aarm events are ogged with a date and time. Nor represents a change to a norma state. Aa represents a change to an aarm state. The text in parentheses denotes the aarm the event appies to. The og can hod up to 40 events. Logged aarm events can be deeted by using the deete icon. If a events are deeted, aarm states can sti be checked by navigating to the BACnet aarm objects via the network browser page. See the BACnet aarm ist for aarm objects. The LCD can be set to sound a continuous beep when a new item is added to the aarm og. This beep is sienced by any user interaction, but the aarm event is sti ogged. This option can be changed via the settings page. View Config 2 Nor(A Cir 2) Nuaire XBC 09:47 16-10-15 1 Aa(A Cir 2) Nuaire XBC 09:44 16-10-15 1 / 1 BACK-UP The LCD settings, favourites and ocked items can be backed up to a usb drive by pugging a usb into the rear of the LCD. The screen wi automaticay change to a downoad screen. Seect the item required and choose upoad. To downoad data to the LCD seect the data type and choose downoad. If a user or service password is forgotten, they can be reset by re-downoading a backup fie to the LCD that has no set password. It is recommended that a backup is made of a LCD with no password set. 38 029 2085 8200 (MS/TP)

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY SETTINGS PAGES These set of pages aow the user to configure the technica functions of the LCD both from the BACnet and user interface perspectives. The settings page requires a service password for access. NETWORK SETTINGS PAGE Aow the user to discover a devices connected on the MS/TP network and browse a objects exposed within these devices. Parameter Name Description Defaut Setting Device Name It defines the BACnet Device Object Name FAD0351 Device ID It defines the BACnet Device Object Identifier 127 MAC Address MSTP Address of FAD 127 Descriptions BACnet Description of FAD Fied Advanced Dispay Baud Rate It defines the FAD communication speed 38400 over the BACnet oca network. Max Info Frames It defines the BACnet Device Object Max_Info_Frames 3 Adjust Priority The Adjust priority parameter defines with which 16 priority the dispay wi command AV / BV / MV vaues. Override Priority The Override priority parameter defines with which 8 priority the dispay wi command AO / BO / MO vaues Page Refresh Time It defines the poing speed at which the FAD wi refresh 30 sec the vaues shown on the screen Max Master This parameter represents the vaue of the Max_Master 127 property of the node's Device object APDU Time The APDU Timeout property defines the amount of time, 3 in seconds, the FAD waits for responses from other devices. DISLAY SETTINGS PAGE Parameter Name Description Defaut Setting Backight It defines whether the back ight remains ON or turns OFF Stand-By ON during Standby Homepage It defines which page to show at power up or pressing the Main Menu Home shortcut button Service Password Password required to enter settings page 0 User Password Password Required to change ocked vaues 0 (A vaues are ocked by defaut) Stand By It defines the behaviour of the dispay once the Stand By Timer - has expired without interactions from the user Stand By Timer It defines the inactivity period, in minutes, required to force 0 min the dispay in Stand By mode and for both Service and User passwords expiration. Defining this parameter to Zero, the passwords request (if any) is prompted at any access to pages requiring them Feedback Sound It defines whether the device sha provide a sound feedback OFF during user interaction Aarm It defines whether the device sha provide a sound feedback OFF when receiving a new Aarm. The notification sound can be continuous (ON) or intermittent (BEEP) Date Time Day Of Week It adjusts settings reated to the Day, Month and Year of the FAD integrated cock It adjusts settings reated to the Hour and Minute of the FAD integrated cock It adjusts settings reated to the Day of Week (1-7) of the FAD integrated cock nuaire.co.uk 39

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY SELECT TARGET DEVICE PAGE Parameter Name Description Defaut Setting Device Name MAC Address Device ID Object Type Object ID Name of the device where the object resides The MSTP address of the device where the object resides The BACnet ID of the device where the object resides The object type The object BACnet ID 9.6.4 VIEW CONFIG Parameter Name Description Defaut Setting Name /Description Chooses whether objects are described by their name Name or description Write Aows editing of objects Yes ID This wi dispay the BACnet ID next to a BACnet objects Yes on the network, favourites and target pages Function This option aows objects to be added to the favourite or None (Favourite/Lock) ocked ist. Once it is seected, navigate to the network page and choose which objects are required. A user password is required to change any ocked object, if set. A vaues are unocked by defaut. MULTIPLE CONTROLLERS When accessing the Network View the FAD aunches a Network Discovery function. The purpose of this function is to find other BACnet devices residing on the same MS/TP trunk. The maximum number of devices supported by the FAD discovery function is 32. WIRING ON 6 7 1 2 1 2 3 4 5 + 12...24 VAC - 12...24 VDC + BACnet - MS/TP Termina Bock Description 1-3 Unused 4 Power Suppy (-) 12...24 VAC / VDC 5 Power Suppy (+) 12...24 VAC / VDC 6 BACnet MS/TP Port (RT-) 7 BACnet MS/TP Port (RT+) Programming USB Port There are two ways of connecting the LCD. 1. Connected to the FC bus using screwed terminas. A separate power suppy is required. 2. If the controer is standaone, the LCD dispay can be connected to the RJ12 FC bus port on the front of the FAC controer. This FC port wi aso power the LCD, so in this case, a separate power suppy is not required. One of the foowing cabes is required to do this. DIP Switch 1 DIP Switch 2 BACnet MS/TP Line Terminator (End of Network 120Ω resistor switch) Unused ESCO-LCD-3M Ecosmart-Connect LCD RJ12 Connection Cabe 3m ESCO-LCD-5M Ecosmart-Connect LCD RJ12 Connection Cabe 5m ESCO-LCD-10M Ecosmart-Connect LCD RJ12 Connection Cabe 10m ESCO-LCD-20M Ecosmart-Connect LCD RJ12 Connection Cabe 20m ESCO-LCD-30M Ecosmart-Connect LCD RJ12 Connection Cabe 30m 40 029 2085 8200 (MS/TP)

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY ROOM MODULES Room Modues are eectronic, wa-mountabe sensors designed to work directy with the Nuaire contro pane. Backit LCD Dispay - A LCD dispay versions of Room Modues incude a dia to adjust room setpoint. Whie the setpoint is being adjusted the backight wi switch on and the dispay wi update to show the setpoint. Whie inactive the dispay wi revert to dispay the current room temperature. The occupancy status is aso dispayed on the LCD. On fan speed override modes the fan speed and override status is aso dispayed. A maintenance icon wi dispay if there is a sensor network error. Service Port - A RJ12 service port is provided at the base of each Room Modue. This aows the temporary connection of an extra modue to the sensor network. Fan Speed Override/Room Humidity - This button cyces through fan speed override settings. Room Humidity - The ESC-RM-2-TDH-120 mode incudes a push button on the face of the network sensor to aow occupants to view the temperature and reative humidity of the zone. Pressing the push button togges between temperature and RH on the LCD. The LCD defauts to temperature 5 seconds after the push button is reeased. Foowing this procedure to permanenty change the defaut dispay: Room modues are automaticay detected and require no set-up. The majority of RM modues monitor room temperature; however, options are avaiabe to aso monitor zone humidity, carbon dioxide (CO2), oca temperature setpoint adjustments, PIR, and other variabes. This data is transmitted to a controer on the Sensor Actuator (SA) Bus. FEATURES 1. If the dispay backight is off, press and reease the push button to iuminate the backight. If the dispay backight is aready on, proceed to Step 2. 2. Press and hod the push button for 5 seconds to switch to the desired defaut dispay (either temperature or RH). Note: The desired defaut dispay wi fash for 5 seconds. After the dispay stops fashing, the new defaut dispay is in effect. 3. Reease the push button; the desired dispay is now the new defaut dispay. The humidity setpoint cannot change via RM sensors. This must be changed through a commissioning too. INSTALLATION Location Considerations Locate the network sensor: on a partitioning wa, approximatey 5 ft (1.5 m) above the foor in a ocation of average temperature away from direct sunight, radiant heat, outside was, outside doors, air discharge gris, or stairwes; and from behind doors away from steam or water pipes, warm air stacks, unconditioned areas (not heated or cooed), or sources of eectrica interference To remove the rear cover 1. Use a pozi screwdriver to oosen the screw on the top of the unit. 2. Insert a coin into the sot next to the security screw ocation, pressing the tab that keeps the unit cosed. Then carefuy pry the top edge of the sensor assemby away from its mounting base and remove. Moduar Jack: For the moduar jack, simpy snap the wiring pug into the jack. A moduar jack requires a straight-through, one-to-one connection (not a crossover). See interconnection section for detais. nuaire.co.uk 41

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY ROOM MODULES WIRING Screw termina wiring: If RJ11 cabes are not used, the screw termina connections on the Room Modues can be used. Standard Sensor Wiring. + - COM SA PWR SA Bus Screw Termina Bock Network Sensor SA+ SA- Bus Com SA Power from Controer (15 VDC) CO2 Sensor Wiring. SA Bus (Brown) 24V (Grey) + - SA COM SA PWR HOT COM Screw Termina Bock Network Sensor The CO2 sensor can connect either through screw terminas or the moduar jack but a 24VAC/DC suppy must be provided in either case. SA+ SA- Bus Com 24 VAC/VDC Power Suppy SA Power from Controer (15 VDC) 42 029 2085 8200 (MS/TP)

120 80 DIMENSIONS ROOM MODULES (MM) ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY 35 80 35 80 nuaire.co.uk 43

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY SENSOR ADDRESSING ESCO-TDFS has a fixed device address of 199 on the SA Bus. The address can be changed on other modes via DIP switches on the PCB rear. The designation of each address is shown in the foowing tabe. Address Range Type Modue Type 199 Fixed Muti-function (with Fan Speed Override) 200-203 Adjustabe Muti-function 212-219 Adjustabe Room CO2 Sensor Modue Each sensor on the SA bus must have a unique address. The defaut controer strategy is preconfigured to automaticay detect a Room Modues on the network and react accordingy. 200-203 Address Switch Settings Address Switch Settings Switch 2 Switch 1 200 OFF OFF 201 OFF ON 202 ON OFF 203 ON ON ROOM MODULES TECHNICAL SPECIFICATIONS Suppy Votage 15VDC (Powered from SA bus) Temperature Measurement Range 0 to 40 C Humidity Measurement Range 0 to 100% (Fu) 10 to 90% (Caibrated) Temperature Sensor Type Loca 1k ohm Patinum Resistance Temperature Detector (RTD); Cass A per IEC 60751 Humidity Sensor Type Thin Fim Capacitive Sensor Temperature Resoution (Modes with ±0.5C LCD) Defaut Temperature Setpoint 10 C to 30 C Adjustment Range PIR Occupancy Sensor Motion Detection Minimum 94 Anguar Degrees up to a Distance of 15 ft (4.6m); Based on a cear ine of sight Ambient Operating Conditions 10 C to 30 C 10 to 90% RH (Temp Probe -10 C to 60 C) Ambient Storage Conditions -20 to 60 C 5 to 95% RH CO2 Sensor Warmup time Less than 1 Minute; ess than 10 minutes for fu accuracy On (Cosed) 2 1 Off (Open) 212-219 Address Switch Settings Address Switch Settings Switch 4 Switch 2 Switch 1 212 OFF OFF OFF 213 OFF OFF ON 214 OFF ON OFF 215 OFF ON ON Not supported ON ANY ANY On (Cosed) 4 2 1 Off (Open) 44 029 2085 8200 (MS/TP)

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY INTERCONNECTION The sensors or other devices on the SA bus network connect either by moduar RJ12 connections or by screwed terminas using pain ended cabe. A sensors are fitted with both. MODULAR CABLE (UP TO 30 METRES) The Room Modues can connect using a 24AWG twisted 3-pair cabe with RJ12 connections over the Sensor Actuator (SA) bus. the foowing items are avaiabe. ESCO-C3M ESCO-C5M ESCO-C10M ESCO-C20M ESCO-C30M ESCO-2WA ESCO-3WA 3m Prefabricated sensor cabe with moduar jacks 5m Prefabricated sensor cabe with moduar jacks 10m Prefabricated sensor cabe with moduar jacks 20m Prefabricated sensor cabe with moduar jacks 30m Prefabricated sensor cabe with moduar jacks 3-port adapter 2-port extension adapter Room Modues must not be fitted more than 30metres (cabe ength) from the controer when using this connection method. MODULAR JACK NETWORK Controer 3-way femae RJ12 adaptor 3-way femae RJ12 adaptor RJ12 Sensor jack 3metres Max 3metres Max RJ12 Pug RJ12 Pug RJ12 Pug Room Modue Room Modue Room Modue Sensor, SA Bus (RJ-12 Moduar Jack) Cabe type: Pre-fabricated 3 twisted pair with RJ12 pugs, 26AWG Power Power (15 (15 VDC) VDC) 6 Bus Bus and and Power Power Common Common 5 Power Power (15 (15 VDC) VDC) 4 Bus Bus and and Power Power Common Common3 2 SA Bus SA Bus - - 1 SA Bus SA Bus + + 6 5 4 3 2 1 nuaire.co.uk 45

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL SOFTWARE STRATEGY PLAIN CABLE (30 TO 150 METRES) If a Room Modue is to be fitted more than 30metres (cabe ength) from a controer, the foowing cabe is recommended. ESCO-MSTPC30M ESCO-MSTPC150M Ecosmart Connect MSTP cabe ree 30m Ecosmart Connect MSTP cabe ree 150m Note: On the SA Bus, the + and - wire are one twisted pair, and the COM and SA PWR are the second twisted pair of wires. These cannot be used with RJ12 connections and must be stripped and connected using screwed terminas. The shied must be earthed at the contro pane end ony and be made continuous aong the bus ength. Room Modues must not be fitted more than 150metres (cabe ength) from the controer. SCREWED TERMINAL NETWORK 150M MAX NETWORK LENGTH Controer Screwed Termina SA Bus Screwed Termina (Brown) Screwed Termina Screwed Termina Room Modue Room Modue Room Modue Cabe type: Pain-ended shieded 2 twisted pair 22AWG 46 029 2085 8200 (MS/TP)

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL ELECTRICAL DETAILS SUPPLY The contro is powered by a 240VAC suppy. This must be isoated oca to the unit and fitted with appropriate overcurrent and faut protection. ELECTRIC HEATER SUPPLY For modes with eectric heating, the heating circuit is powered by a separate, higher current, 240VAC suppy. This must be isoated oca to the unit and fitted with appropriate overcurrent protection. The main suppy is sti required. ELECTRICAL SUPPLY DETAILS Unit Main Circuit Eectric Heater Circuit (FLC) Code (FLC) (Eectric Modes Ony*) XBC10-H-*CO 3.2 A 13 A XBC15-H-*CO 4.5 A 13 A XBC25-H-*CO 8 A 19 A XBC45-H-*CO 8 A 19 A XBC55-H-*CO 8 A 38 A XBC65-H-*CO 8 A 38 A *Eectric Heater modes require two separate suppies, each with an appropriate overcurrent current protection device. VOLT FREE CONTACTS Note that the vot free contacts are not fused. If these are used to power any externa equipment, the instaer must provide adequate fusing or other protections. These contacts are rated at 3A resistive, 0.5A inductive. Run connections - The reay is powered when the fan is running. (These contacts are used when an I/O damper is instaed. Faut connections - No faut = the reay is powered. Faut - the reay is unpowered. Heat demand - the reay is powered when heating is seected. Coo demand - the reay is powered when cooing is seected. SWITCHED LIVE Switch Live (SL) termina - A signa of 100-230V a.c. wi activate the switched ive signa. Switch Live 2 (SL2) termina - A signa of 100-230V a.c. wi activate the switched ive 2 (Fan Boost) signa. Note that a signa from an isoating transformer wi produce an unpredictabe resut and is not recommended. Vot free versions of the switched ive signas are aso avaiabe at terminas T33-T34 & T35-T36. Link two contacts to activate the signa. DAMPER CONNECTIONS A fan start deay can be imposed to aow the damper time to open. This is adjustabe via dispay screens or commissioning toos. If an I/O damper is fitted, it must be wired to the fan run reay, and the reay suppied with the reevant suppy votage. See I/O Damper connection diagram for detais. NETWORK SETTINGS Defaut MS/TP Address: 4 BACnet Instance Number: Randomised & Unique for each controer (0 to 4,194,304) CONNECTION CHART Description Controer Din Rai Reay Termina No Termina No DI AI Output AO Fresh Air Sensor IN 1 1 Suppy Air Sensor IN2 1 Return/Room Air Sensor IN3 25-26 1 Input 4 IN4 1 Input 5 IN5 31-32 1 Aarm Circuit 1 (Fan, Heater) IN6 27-28 (Some Modes) 1 Aarm Circuit 2 (Pump, Fiter) IN7 29-30 1 Vot-Free Enabe Input Signa IN8 33-34 1 Vot-Free Boost Input Signa IN9 35-36 1 Extract Fan 0-10V OUT1 1 Suppy Fan 0-10V OUT2 1 Heat Demand 0-10V OUT3 1 Coo Demand 0-10V OUT4 1 Bypass Damper Reay OUT5 1 Vot-Free Heathy Reay OUT6 1 Vot-Free Fan Run Reay OUT7 1 Vot-Free Coo Demand Reay OUT8 1 Vot-Free Heat Demand Reay OUT9 1 230V Enabe Input 10 1 230V Fan Boost Input 11 1 nuaire.co.uk 47

ECOSMART CONNECT CONTROL (CO) DESCRIPTION OF CONTROL ELECTRICAL DETAILS TERMINALS - WIRE CONNECTIONS This contro unit utiises WAGO s CAGE CLAMP S termina bocks, aowing for quick and easy connection. PUSH IN TERMINATION - Stripped soid conductors, fine-stranded conductors with ferrues, or utrasonicay bonded conductors are simpy pushed in unti they hit the backstop. No too required. TERMINATION OF FINE-STRANDED CONDUCTORS - Open the camp by inserting an operating too (as shown beow) unti it cicks into position. Then insert the conductor and remove the operating too to compete the connection. CONDUCTOR REMOVAL - Insert an operating too in to the operating sot to remove the conductor, just ike the origina CAGE CLAMP termina bocks. JUMPERS - Termina bocks can be commoned together to increase the number of terminas at the same potentia using push-in jumpers. In these cases the terminas are treated as one conductor. JUMPER REMOVED - Insert the operating too bade between the jumper and the partition wa of the dua jumper sots, then ift up the jumper. DOUBLE DECK TERMINAL BLOCK - Each deck has a different potentia (2-conductor), which creates a space saving on the rai. Decks can be commoned to adjacent termina bocks and/or the top to the bottom deck. EARTH TERMINAL BLOCKS - The earth termina bock (green/yeow) has a direct eectrica connection to the DIN rai, with the earthing foot (earth connection ony). FUSE TERMINALS - Repaceabe cartridge fuses are housed in quick reease fuse terminas. 48 (MS/TP)

ECOSMART CONNECT CONTROL (CO) CONSULTANTS SPECIFICATION CONSULTANTS SPECIFICATION ECOSMART CONNECT - CONTROLLER BASED VENTILATION Ecosmart Connect is preconfigured with a fexibe software strategy. The contro features incude the foowing functions as standard Individua Fan Speed Adjustment Tricke Mode Run-on Inteigent Run-on (Occupancy Sensitive) Weeky Scheduing Night Cooing Purge Mode Frost Protection Faut Monitoring A commissioning features are adjustabe remotey without direct access to the AHU. This can be via a service port on any room sensor or over the network. The temperature contro can be set to reguate suppy air or to reguate room air temperature to a defined setpoint. The heat exchanger bypass (where appicabe) is automaticay operated according to temperature and a pre-defined strategy. Nuaire room sensor modues are automaticay detected and actioned upon accordingy. Mutipe sensor options are avaiabe in a singe modue. A singe ESCO-LCD pane can commission/monitor a singe controer or mutipe controers on the network. The Ecosmart Connect contro modue can be connected to provide the foowing integrated BMS interfaces. Higher Leve (BACnet) Nuaire Room Sensor Network BACnet MS/TP (As standard) BACnet Ethernet IP optiona (via converter box) Lower Leve Switched Live & Vot Free Enabe Switched Live & Vot Free Fan Boost / Heat Boost (Configurabe) 2x 0-10V input. Configurabe to accept Temperature, CO2, Humidity and Pressure. 4 x Vot free reay outputs. Fan run, Heat, Coo & Faut. Units fitted with Ecosmart Connect contro have a 5 year warranty. nuaire.co.uk 49

ECOSMART ADAPT CONTROL WITH TREND (AT) CONTROL OPTION Ecosmart Adapt Contro - Ecosmart Adapt is project/site specific and can be adapted to utiise other controers such as Siemens, Johnson s etc. for further detais contact Nuaire. From November 2015 Ecosmart2 wi be rebranded as an Adapt option. The Ecosmart Adapt (with Trend) option is fitted with an IQ422/12/LAN/BAC/230 controer aowing for unitary contro and fu BMS integration via BACnet IP (by others). Controer software is basic and ready for project specific program to be oaded. Doesn t cost the Earth... Doesn t cost the Earth... 50 029 2085 8200

INDEX FOR CONTROL PAGE ECOSMART ADAPT (with TREND) - FEATURES AND BENEFITS 52 ECOSMART ADAPT (with TREND) - SENSORS AND ENABLERS 53 ECOSMART ADAPT (with TREND) - DESCRIPTION OF CONTROL 54-56 ECOSMART ADAPT (with TREND) - ELECTRICAL DETAILS 57-58 ECOSMART ADAPT (with TREND) - CONSULTANTS SPECIFICATION 59 If you have a requirement for Ecosmart Adapt contact Nuaire. Doesn t cost the earth... nuaire.co.uk 51

ECOSMART ADAPT CONTROL WITH TREND (AT) CONTROL FEATURES & BENEFITS The Adapt range of contros are project specific as an exampe we have used the Trend IQ422/12/LAN/BAC/230 controer but Nuaire can aso offer other contro options. For further detais contact Nuaire. The management and contro of modern buidings grow ever more sophisticated. A Buiding Energy Management system (BEMS) must be taiored to suit each customer s specific contro requirements. It must provide efficient HVAC contro, couped with the fexibiity to accommodate changes in occupancy status and staff reocation at short notice; whist simutaneousy deivering improved comfort conditions. A BEMS must aso provide rea time management information and contro, enabing customers to achieve significant energy savings (Trend). Adapt Trend provides contro of the ventiation incuding the heating, or cooing aowing unitary contro and fu BMS integration via BACnet IP. The Adapt Trend contro system incudes an IQ422/12/LAN/BAC/230 controer which is preconfigured and the unit and contro assemby is functionay tested at Nuaire before customer deivery. REDUCED INSTALLATION TIME - The Adapt Trend IQ422/12/LAN/BAC/230 has software configurabe inputs and addressing with automatic baud rate seection and IQToo compatibiity. This greaty reduces engineering and commissioning time and therefore reducing the cost of the insta. COST EFFECTIVE MEANS OF CONTROLLING A VARIETY OF APPLICATIONS - Provides inteigent contro of a wide range of pant. Power to support advanced contro appications incuding remote web supervision with graphica representation and contro adjustments. BAUD RATE - Is automaticay detected and appied to the network. SOFT CONFIGURABLE UNIVERSAL INPUTS - No need for jumper settings. BARCODE ADDRESSING - Makes for quick and easy commissioning. NETWORK ADDRESSING - Via SET, no DIP switch setting required. PEACE OF MIND - Ecosmart Adapt with Trend has a 5 year warranty. ECOSMART ADAPT (TREND) SUPPLY & EXTRACT VENTILATION SYSTEM CONNECTED TO ROOM MOUNTED SENSOR Room mounted Sensor 52 029 2085 8200 (IP)

ECOSMART ADAPT CONTROL WITH TREND (AT) SENSORS & ENABLERS To hep you seect the appropriate contro soution for your appication, simpy refer to one of the options beow. For the fu range and technica detais, pease visit www.nuaire.co.uk THERMISTOR TEMPERATURE SENSORS Low cost thermistor sensors comprising insertion, camp-on, and outside air versions. The insertion sensor may be used for duct or immersion purposes. It has a 6mm diameter brass probe which is suitabe for retrofit immersion appications and wi fit most existing pockets (universa fitting kit option). Code: TB/T1/S For duct or immersion use. Short 150mm. TB/T1/L For duct use ony. Long 400mm FEATURES Low cost High quaity thermistors Brass probes M20 conduit entry with M16 cabe gand IP67 housing Quarter turn quick reease id Easy to wire Universa kit option for retrofit of immersion sensors Adjustabe insertion depth fange option for duct sensors DUCT HUMIDITY & TEMPERATURE SENSORS Duct mounted reative humidity and temperature sensors for HVAC appications. The certified 2% high accuracy (/2%) and standard 3% versions offer exceent inearity and stabiity over a wide humidity range (10 to 90 %RH). Code: HT/D Duct and thermistor sensor (+/-3%). FEATURES Pre-caibrated for ease of commissioning IP65 Operates over 10 to 100 %RH non-condensing ± 3% accuracy versions 2 part connectors for ease of instaation Humidity sensor eement protected by repaceabe fiter Capacitive humidity sensing eement provides exceent ong term stabiity Adjustabe depth duct mounting fange option CO2 SENSORS The CO2 duct and space sensors monitor the carbon dioxide concentration and temperature of the air. The space sensors have additiona options of humidity monitoring and a 4 digit dispay. The dispay wi show the measured vaues in succession. The duct sensor has a quick-reease id to faciitate instaation. Code: CO2/T/D Duct sensor. Code: CO2/T/S Space carbon dioxide concentration and temperature sensor. FEATURES Low cost, high quaity thermistor temperature sensor Humidity monitoring option for space sensor Optiona digita dispay for space sensor IP67 housing (duct sensor) Quarter turn quick reease id (duct sensor) Two part terminas to faciitate wiring 24 Vac/dc suppy Adjustabe depth duct mounting fange option TOUCH SCREENS IQVIEW4 TOUCH SCREEN DISPLAY (6 x 4 inch). FPK/Pate Mounting pate. IQVIEW4/SM BOX Surface mount box for wa or pane. Transformer for IQVIEW4 incuded. ACC/24V - 230/24 VAC, 36 VA IQVIEW8 TOUCH SCREEN DISPLAY (10 x 6 inch). IQVIEW8/SM BOX Surface mount box for fat surfaces. Transformer for IQVIEW8 incuded. ACC/24V 230/24 VAC, 36 VA SDU DISPLAY RD/SDU-IQ2COMMSCABLE/3m RJ11 pug to RJ11 pug cabe (3m) for SDU. nuaire.co.uk 53

ECOSMART ADAPT CONTROL WITH TREND (AT) DESCRIPTION OF CONTROL SOFTWARE STRATEGY GENERAL The system incorporates a web enabed Trend IQ422/12/LAN/BAC/230 controer. A comprehensive unit contro specification - factory fitted and tested to provide guaranteed operation from a singe suppier. BOOST When the contro receives a boost signa the fans wi run at boost speed. Once the signa is removed the fans wi run on for a time defined by the boost run-on setpoint. TRICKLE MODE When tricke mode is active, the fans wi run at their minimum speed even when there is no enabe signa. Heating and cooing wi aso function in this mode if avaiabe. CO 2 CONTROL When a CO2 sensor is seected via UI4 & 5 function knobs, and an enabe signa is received, ventiation wi increase to reduce CO2 concentration the target CO2 setpoint. The target CO2 sensor setpoint can be changed as one of the commissioning setpoints. SUPPLY TEMPERATURE CONTROL Whie an enabe signa is present, this mode moduates heating, cooing & heat exchanger bypass dampers with the aim of the suppy air reaching the temperature setpoint. Pease note that heating and cooing outputs wi ony function if the HeatingType or CooingType setpoints are set to heating or cooing options. THE NUAIRE UNIT CONTAINS THE FOLLOWING CONTROLLABLE ITEMS: Inet Damper (if fitted). Exhaust Damper (if fitted). Heat Recovery and Bypass Damper. Heating Coi. Cooing Coi. Suppy Fan Speed. Extract Fan Speed. ENABLE SIGNAL The unit can be enabed via the foowing methods: Software switch (ENABLE) via SDU, IQView4, IQView8 or network. Switched ive (230VAC) input, PIR etc. Low votage contacts. Night cooing / summer free-cooing strategy. Schedued via weeky caendar. When the enabe signa is removed, the unit wi run on for a time defined by the run-on setpoint. If an eectric heater is fitted, the fans wi automaticay run-on for an extra 2 minutes, without heating, in order to dissipate residua heat. OCCUPANCY CONTROL When a Trend occupancy sensor is seected via UI4 & 5 software modue, the contro wi ook for a Trend OCC-U sensor in the appropriate input. An occupied signa wi give an enabe signa. 0V = Occupied 14V = Unoccupied FROST PROTECTION Shoud the interna temperature of the unit fa beow a vaue defined in the commissioning variabes, the contro wi override a heating/cooing ogic to open the LPHW or CW contro vaves, if fitted. This is to aow any protective fow through the heating/cooing cois. The suppy fan wi aso stop and the appropriate frost protection software modue wi enter an aarm state. This period wi ast for a minimum of 5 minutes by defaut. The faut reay wi aso open. Heat and coo demand reays wi not operate but digita inputs Frost Protecting LPHW or Frost protecting CW wi enter an aarm state. Pease note that frost protection wi ony function if the HeatingType or CooingType setpoints are set to LPHW or CW. NIGHT COOLING / SUMMER FREE COOLING Once enabed in software, this routine uses an individua time schedue to coo the fabric of the buiding at night using ony the externa air. This mode ony functions if the daytime temperature is above the setpoint, cooing is possibe and if the cooing air is not too cod. ALARMS CRITICAL ALARM (LATCHING) Once in critica aarm state the unit wi drive a heating and cooing outputs to 0V. Other functions continue as norma. The critica aarm is atched and required power cyce to cear. Causes of critica aarm: Fan fai via faut circuit 1. Heater overtemp via faut circuit 1. 54 029 2085 8200 (IP)

ECOSMART ADAPT CONTROL WITH TREND (AT) DESCRIPTION OF CONTROL SOFTWARE STRATEGY MAINTENANCE ALARMS (NON-LATCHING) Once in maintenance aarm state the ony action taken is de-energising of the faut reay. Once the trigger is removed, the aarm wi reset automaticay. Causes of maintenance aarm: Condensate pump faut via aarm circuit 2 (This bypasses the heater exchanger automaticay) Sensor Faiure Low suppy temperature, defaut 8 C. (This can be set to stop fans if required) Frost protection routine active, defaut 4 C (This ony runs if water vaves are seected as fitted) Excessivey high suppy temperature reading (this wi stop heating) A aarms have a hod off period set by the setpoint Aarm Deay. THERMAL TRIP In case of software faiure, as a fina resort, the eectric heater is protected by a fai-safe therma overoad switch. This switch disabes the heater controer once the temperature reaches 80 C. When this occurs, the critica aarm wi atch in software. Once the unit coos, the contactor wi re-engage but the heater signa wi remain at 0V unti the critica faut is reset in software or by power cyce. SETPOINTS A the foowing are user adjustabe within engineered imits: Point Name Description Range Defaut ENABLE Software enabe switch Off / On Off RUNONTIME Run-on timer vaue 0-3600 Seconds 0 TRICKLEMODE When On, fans wi tricke even with no enabe signa Off / On Off SETTEMP Desired temperature setpoint 10 to 30 C 22 DEADBAND Dead-band for temp contro 0.5 K to 10 K 3 BOOST Software boost switch Off/On Off BOOSTRUNON Boost Run On 0-3600 Seconds 0 FROSTPROTEMP Temperature, beow which, any water vaves wi be overridden open -40 C to 10 C 4 MINFROSTPROTECTPERIOD Minimum time frost protection wi be enabed 0-600 Seconds 300 DAMPERDELAY Startup deay to aow I/O dampers to open 0-300 Seconds 0 ALARMDELAY Aarm hod-off deay 0-20 Seconds 5 HIGHAIRTEMPALARM High suppy air temp aarm temperature 30 to 70 C 50 LOWTEMPALARM Low suppy air temp aarm temperature -40 C to 20 C 8 FORCESTOPONLOWTEMP Stops fans upon LOWTEMPALARM Off/On Off ALARMRESET Resets any atched aarms (Resets to Off Automaticay) Off/On Off SUPPLYFANMAX Individua fan maximum speed setting 20-100% 100 SUPPLYFANMIN Individua fan minimum speed setting. (Tricke speed) 0-100% 20 EXTRACTFANMAX Individua fan maximum speed setting 20-100% 100 EXTRACTFANMIN Individua fan minimum speed setting. (Tricke speed) 0-100% 20 SUPPLYFANBOOST Suppy fan boost speed 20-100% 100 EXTRACTFANBOOST Extract fan boost speed 20-100% 100 SUPPLYFANSTARTVOLTAGE The votage threshod of passing 0% rotationa speed 0-5V 1 EXTRACTFANSTARTVOLTAGE The votage threshod of passing 0% rotationa speed 0-5V 1 SUPPLYFANVOLTAGELIMIT The maximum votage to be suppied to the fan motor 6-10V 10 EXTRACTFANVOLTAGELIMIT The maximum votage to be suppied to the fan motor 6-10V 10 CO2TARGET The target setpoint for CO 2 contro 0-10000PPM 650 CO2RANGEMIN The ower imit CO 2 vaue corresponding to the imit votage 0-10000PPM 0 CO2VOLTAGEMIN The ower imit votage corresponding to the imit of range 0-10VDC 0 CO2RANGEMAX The upper imit CO 2 vaue corresponding to the imit votage 0-10000PPM 2000 CO2VOLTAGEMAX The upper imit votage corresponding to the imit of range 0-10VDC 10 CO2-LOOPGAIN CO 2 Loop Gain 0 to -30-0.5 CO2-LOOPINTEGRAL CO 2 Loop Integra 0 to 30 10 CO2-LOOPDERIVATIVE CO 2 Loop Derivative 0 to 30 0 nuaire.co.uk 55

ECOSMART ADAPT CONTROL WITH TREND (AT) DESCRIPTION OF CONTROL SOFTWARE STRATEGY SETPOINTS (CONTINUED) A the foowing are user adjustabe within engineered imits: Point Name Description Range Defaut SUMMERNIGHTFREECOOLACTIVE Set night cooing mode as active Off / On 0 SUMMERNIGHTFREECOOLMINTEMP Night cooing ower cut-off temperature 5-30 C 10 SUMMERNIGHTFREECOOLFANSPEED Night coo fan speed 20-100% 80 STC-COOLLOOPGAIN Suppy Temp Contro - Coo Loop Gain 0 to -30-5 STC-COOLLOOPINTEGRAL Suppy Temp Contro - Coo Loop Integra 0 to 30 2 STC-COOLLOOPDERIVATIVE Suppy Temp Contro - Coo Loop Derivative 0 to 30 0 STC-HEATLOOPGAIN Suppy Temp Contro - Heat Loop Gain 0 to -30-5 STC-HEATLOOPINTEGRAL Suppy Temp Contro - Heat Loop Integra 0 to 30 2 STC-HEATLOOPDERIVATIVE Suppy Temp Contro - Heat Loop Derivative 0 to 30 0 HEATINGTYPE Heating Type 0=None, 1=LPHW, 2=Eectric 0-2 0 COOLINGTYPE Cooing Type 0=None, 1=CW, 2=DX 0-2 0 UI4FUNCTION Input 4 Function, 0 = None, 1 = CO 2 /T/D, 2 = Trend Occ, 3=FSC 0-3 0 UI5FUNCTION Input 5 Function, 0 = None, 1 = CO 2 /T/D, 2 = Trend Occ, 3=FSC 0-3 0 TACHOFITTED Is a tacho signa monitor PCB fitted? Off / On Mode Dependant SOFTWAREVERSION Shows the software number & Version N / A 0 FANANDHEATERTEST Factory Use Ony (This resets on power cyce) Off / On Off WIRINGVERIFICATION Factory Use Ony (This resets on power cyce) Off / On Off FORCEOVERHEAT Factory Use Ony (This resets on power cyce) Off / On Off DAMPERBYPASS Force bypass damper into bypass mode (This resets on power cyce) Off / On Off DAMPEROUTOFBYPASS Force bypass damper out of bypass mode (Pump faiure or DAMPERBYPASS switch wi override this) (This resets on power cyce) Off / On Off FANDAMPERTEST Factory Use Ony Off / On Off 56 029 2085 8200 (IP)

ECOSMART ADAPT CONTROL WITH TREND (AT) DESCRIPTION OF CONTROL ELECTRICAL DETAILS SUPPLY The contro is powered by a 240VAC suppy. This must be isoated oca to the unit and fitted with appropriate overcurrent and faut protection. ELECTRIC HEATER SUPPLY For modes with eectric heating, the heating circuit is powered by a separate, higher current, 240VAC suppy. This must be isoated oca to the unit and fitted with appropriate overcurrent protection. The main suppy is sti required. ELECTRICAL SUPPLY DETAILS Unit Main Circuit Eectric Heater Circuit (FLC) Code (FLC) (Eectric Modes Ony*) XBC10-H-*AT 3.2 A 13 A XBC15-H-*AT 4.5 A 13 A XBC25-H-*AT 8 A 19 A XBC45-H-*AT 8 A 19 A XBC55-H-*AT 8 A 38 A XBC65-H-*AT 8 A 38 A *Eectric Heater modes require two separate suppies, each with an appropriate overcurrent current protection device. VOLT FREE CONTACTS Note that the vot free contacts are not fused. If these are used to power any externa equipment, the instaer must provide adequate fusing or other protections. CONNECTION CHART These contacts are rated at 3A resistive, 0.5A inductive. Run connections - The reay is powered when the fan is running. (These contacts are used when an I/O damper is instaed. Faut connections - No faut = the reay is powered. Faut - the reay is unpowered. Heat demand - the reay is powered when heating is seected. Coo demand - the reay is powered when cooing is seected. SWITCHED LIVE Switch Live (SL) termina - A signa of 100-230V a.c. wi activate the switched ive signa. Switch Live 2 (SL2) termina - A signa of 100-230V a.c. wi activate the switched ive 2 (Fan Boost) signa. Note: a signa from an isoating transformer wi produce an unpredictabe resut and is not recommended.vot free versions of the switched ive signas are aso avaiabe at terminas T33-T34 & T35-T36. Link two contacts to activate the signa. DAMPER CONNECTIONS A fan start deay can be imposed to aow the damper time to open. This is adjustabe via dispay screens or commissioning toos. If an I/O damper is fitted, it must be wired to the fan run reay, and the reay suppied with the reevant suppy votage. See I/O Damper connection diagram for detais. NETWORK SETTINGS IP address is 192.168.11.12 Subnet mask 255.255.255.0 Lan 011, node 012 IQ422 Expansion Modue Din Rai Description Termina No. Termina No. Termina No. DI AI DO AO 4DIX Input 3RM-1 Reay Modue (TRM Mode wired for binary switching) 3RM-2 Reay Modue (HRM Mode) Fresh Air Sensor 1 (4,5) 1 Suppy Air Sensor 2 (6,7) 1 Return/Room Air Sensor 3 (8,9) 25-26 1 Input 4 4 (10,11) 1 Input 5 5 (12,13) 31-32 1 Aarm Circuit 1 (Fan, Heater) 4DIX Termina A 27-28 (Some Modes) 1 Aarm Circuit 2 (Pump, Fiter) 4DIX Termina B 29-30 1 6 (14,15) Vot-Free Enabe Input Signa 4DIX Termina C 33-34 1 Vot-Free Boost Input Signa 4DIX Termina D 35-36 1 Extract Fan 0-10V 7 (16,17) 1 Suppy Fan 0-10V 8 (18,19) 1 Heat Demand 0-10V 9 (20,21) 1 Coo Demand 0-10V 10 (22,23) 1 Bypass Damper Wired for binary switching. 1 11 (24,27) See 3RM Datasheet for info. Heathy signa to Reay 4 1 Link from IQ422 GND to AC GND 11 (25) 23 Vot-Free Fan Run Reay 12 (26,27) 3RM-2 Reay 1 1 Vot-Free Coo Demand Reay 3RM-2 Reay 2 1 Vot-Free Heat Demand Reay 3RM-2 Reay 3 1 230V Enabe Input 10 1 230V Fan Boost Input 11 1 Vot-Free Heathy Reay 13-14 1 nuaire.co.uk 57

ECOSMART ADAPT CONTROL WITH TREND (AT) DESCRIPTION OF CONTROL ELECTRICAL DETAILS TERMINALS - WIRE CONNECTIONS This contro unit utiises WAGO s CAGE CLAMP S termina bocks, aowing for quick and easy connection. PUSH IN TERMINATION - Stripped soid conductors, fine-stranded conductors with ferrues, or utrasonicay bonded conductors are simpy pushed in unti they hit the backstop. No too required. TERMINATION OF FINE-STRANDED CONDUCTORS - Open the camp by inserting an operating too (as shown beow) unti it cicks into position. Then insert the conductor and remove the operating too to compete the connection. CONDUCTOR REMOVAL - Insert an operating too in to the operating sot to remove the conductor, just ike the origina CAGE CLAMP termina bocks. JUMPERS - Termina bocks can be commoned together to increase the number of terminas at the same potentia using push-in jumpers. In these cases the terminas are treated as one conductor. JUMPER REMOVED - Insert the operating too bade between the jumper and the partition wa of the dua jumper sots, then ift up the jumper. DOUBLE DECK TERMINAL BLOCK - Each deck has a different potentia (2-conductor), which creates a space saving on the rai. Decks can be commoned to adjacent termina bocks and/or the top to the bottom deck. EARTH TERMINAL BLOCKS - The earth termina bock (green/yeow) has a direct eectrica connection to the DIN rai, with the earthing foot (earth connection ony). FUSE TERMINALS - Repaceabe cartridge fuses are housed in quick reease fuse terminas. 58 029 2085 8200

ECOSMART ADAPT CONTROL WITH TREND (AT) CONSULTANTS SPECIFICATION CONSULTANTS SPECIFICATION ECOSMART ADAPT WITH TREND - ENHANCED DEMAND CONTROLLED VENTILATION A comprehensive unit contro specification - factory fitted and tested to provide guaranteed operation from a singe suppier one who wi take responsibiity. The unit integrated Ecosmart Adapt system provides the faciity for operationa efficiency and energy saving by aowing a comprehensive range of unitary contro functions and / or fu BMS integration (by others) via standard BACnet IP configuration. The system incorporates a web access enabed Trend IQ422/12/LAN/BAC/230 controer, and is augmented by appication specific unit interface and diagnostic circuits. Controer software is optimised and pre-configured, and each unit / contro assemby is fuy functionay tested at works (Refer to technica documentation for fu controer functiona specification). Units fitted with Ecosmart Adapt contro have a 5 year warranty. nuaire.co.uk 59

FOR MORE INFORMATION www.nuaire.co.uk COMMERCIAL www.nuaire.co.uk/commercia AIR HANDLING UNITS www.nuaire.co.uk/boxerahu NUAIRE LIMITED Western Industria Estate Caerphiy CF83 1NA t +44 (0)29 2085 8200 f +44 (0)29 2085 8300 e info@nuaire.co.uk www.nuaire.co.uk As part of our poicy of continuous product deveopment Nuaire reserves the right to ater specifications without prior notice. Teephone cas may be recorded for quaity and training purposes. Part Number 671729 November 2015. 05. 09. 15. Leafet Number 671710