Reliable Push Button Activated Air Metering or Infrared Control Available in a 54" or 36" Bowl Size Wall-Mounted or Floor-Mounted Standard Height Model with Hand or Infrared Control Is ADA Compliant Factory Tested and Shipped Preassembled Vandal Resistant and Easy to Clean Specifi cations Size and Capacity Accommodates 3 users (36" models) or 4 users (54" models) at a time, using less water, energy and space than lavs equipped with conventional faucets. The sectional sprayhead module is controlled by a push button, which actuates an air valve (hand or foot control models), or an infrared sensor-actuated solenoid valve. Flow restrictor keeps flow rate constant at 0.5 GPM per station for all pressures. Operating range is 20-80 PSI. SN2004/IR SN2004/AST4/BS Construction Bowl and Pedestal All exposed materials are type 304 stainless steel polished to a #4 finish. Bowl, pedestal and access panels, frame, foot control housing; support tube; and sprayhead are heavy gauge stainless steel. Exposed fittings are chrome plated. Vandal Resistance Bowl and support tube are an integrally welded assembly, with the support tube welded to an extruded flange from bowl. Sprayhead nozzles and push buttons/infrared sensors are secured to unit from inside the sprayhead module. Air valves/solenoid valves are safely concealed inside the washfountain. Access panels are removable. All supply and waste connections are concealed within the pedestal. Code Compliance and Certifi cations UPC Approval Sentry TM Washfountains are Uniform Plumbing Code (UPC) approved through the International Association of Plumbing and Mechanical Officials (IAPMO). Barrier-Free (ADA Compliant) Standard Height Models Only Wall-mounted models (when mounted at standard height) and standard height floormounted models with hand or infrared control are designed to comply with all ADA guidelines on reaches, clearances and operation. Standard Equipment Valves and Fittings In addition to the bowl and pedestal, the following valves and fittings are standard: manual mixing valve, check stops and strainers. Check valves are 1/2" NPT female. Activation Controls Air Valve Hand Control (AST4) Each push button pneumatically actuates a non-hold-open, air metering, singletemperature valve with field adjustable timing from 0 45 seconds. Factory preset at 10 seconds. Each push button activates one valve which, in turn, activates one station. Push button requires less than five pounds of pressure. C U P C Page 1 of 7 R SN2004/AST4-F/STD Models (Must select one) Model, Size, Stations Description Model, Size, Stations Description SN2003* 36" 3 Floor-Mounted SN2023* 36" 3 Wall-Mounted SN2004* 54" 4 Floor-Mounted SN2024* 54" 4 Wall-Mounted Standard Selections (Must select one from each category) Drain Type (select one) A Off-line vent with supplies from below B Centrally rising vent with supplies from above Controls (select one) AST4 Hand Control Metering Air Valve IR Infred Activation H O Centrally rising vent with supplies from below Off-line vent with supplies from above AST4-F Foot Control Hold-Open Air Valve ** Pedestal Height (Models SN2003 & SN2004 only) (select one) STD Standard Pedestal Height JUV Juvenile Pedestal Height Supply Fittings (select one) TMA Thermostatic Mixing Valve PBV Pressure Balance Mixing Valve TL Tempered Line Supply Soap Dispenser (select one) LSD Liquid Soap Dispenser NSD No Soap Dispenser Backsplash (select one) BS Backsplash NBS No Backsplash Optional Selections Paper Towel Dispensers CTD (2) C-Fold, Multi-Fold Dispenser Stainless Steel Shroud SH Stainless Steel Shroud (Conceals overhead plumbing) SFTD (2) Single-Fold Dispenser * These models in standard height with AST4 or IR controls are ADA compliant. ** Non-cancelable, not-returnable.
Air Valve Foot Control (AST4-F) Each push button pneumatically actuates a hold-open air single temperature valve with slow closing upon release of foot pressure. Push button requires less than five pounds of pressure. Infrared Control (IR) Each of the stream formers is controlled by a separate solenoid valve. Hands placed within the bowl are detected by an infrared sensor module, which activates a flow of tempered water from one spray nozzle. Shut-off is automatic after hands are removed from the detection area. The infrared sensor module uses two zone-focused infrared transmitting beams, having a detection area adapted to, but not exceeding, the bowl perimeter. The Rough-In Dimensions for Bowl and Pedestal Wall Anchors detection range projects 6 9 inches forward at a 30 angle to each side and reaches 15 below horizontal. The infrared sensor is not affected by varying color tones or darkness. Direct sunlight or bright washroom lights will not activate the system. Infrared models also include solenoid valves and a low voltage transform as standard equipment: Solenoid 24V, 50/60 Hz, 3/ NPT. Few moving parts, and resistant to most chemicals, minerals, and impurities often present in municipal water supplies. Low-Voltage Transformer Class II UL/CSA listed, 110/24 VAC plug-in transformer. Plugs into a standard GFCI protected electrical outlet. Location of transformer per local electrical code. 36: 13-3/ (340) 54: 22-3/ (568) 36: 13-3/ (340) 54: 22-3/ (568) 32-1/2"* (826) 4" (102) 1-3/4" (44) 4" (102) 24-3/4"* (629) 110 Volt Electrical Box for Units with IR Activation (Recommended Location; See Local Electrical Codes Before Roughing in) 8-3/ JUV STD Floor Mounted Only 8-3/ JUV STD Floor Mounted Only Floor Mounted Only 4-3/4" (121) 14-3/4"* (375) 14-1/2"* (368) Rough-In Notes Anchor locations for 3/ diameter bolts, both supplied by installer. Wall mounted 54" and 36" models with Infrared or hand control are ADA compliant when mounted at standard height dimensions. Page 2 of 7 11-12-2008
Dimensions - Sentry TM 54" Floor Mounted Infrared Control with Hand Control 2* 2* 16-3/ 25-1/4" (641) 16-3/ 25-1/4" (641) Foot Control 8-11/16"* (221) 2-1/4" (57) 25-1/4" (641) 4-1/ (105) Standard height 54" models with Infrared or hand control are ADA compliant when mounted at standard height dimensions. Page 3 of 7
Dimensions - Sentry TM 36" Floor Mounted Infrared Control with Hand Control Foot Control 3-1/16"* (81) 2-1/4" (57) 17" (432) 3-15/16" (100) Standard height 36" models with Infrared or hand control are ADA compliant when mounted at standard height dimensions. Page 4 of 7 11-12-2008
Dimensions - Sentry TM 54" and 36" Wall Mounted 54" Infrared Control with 54" Hand Control 2* 2* 16-3/ 35-1/4" (895) 16-3/ 35-1/4" (895) 36" Infrared Control with 36" Hand Control 2* 2* Wall mounted 54" and 36" models with Infrared or hand control are ADA compliant when mounted at standard height dimensions. Page 5 of 7
Rough-In Dimensions for Drain and Supplies Type A Off-line vent with supplies from below 2-3/4" (70) 1/2" NPT Supplies 5" (127) 5" (127) Through Floor: Stub Up 3" (76) (Optional) Centerline of Washfountain 4-1/2" (114) 1/2" NPT Supplies Through Floor: Stub Up 2-1/2" (64) (Optional) : Stub out to Suit Trap Type B Centrally rising vent with supplies from above 2-3/4" (70) Through Floor: Stub Up 3" (76) (Optional) 36: 7-9/16" (192) 54: 8-1/16" (205) 36: 54: 9-1/4" (235) 1/2" Nom. Copper Tube Supplies from Above Must Be Located on These Centers to Pass Through Washfountain Shroud and Sprayhead 1/2" NPT Supplies Centerline of Washfountain 1/2" NPT Supplies from Above Vent from Above 1/2" NPT Supplies Supplies and Drain Through Floor (Optional) ** : Stub out to Suit Trap Drain Through Floor (Optional) ** Std: 12" (305) Juv: ** Floor Mounted Units Only Type A Drain Supplies below Off-drain vent P-Trap furnished by others Type B Drain Supplies above Centrally-rising vent P-Trap furnished Rough-In Notes 1. Maximum flow rate required to washfountain is 1.5 GPM for Models SN2003 and SN2023 or 2.0 GPM for Model SN2004 and SN2024. Size supply lines accordingly. 2. Unit with A" drain and paper towel dispensers and/or a shroud, should use H" drain Rough-Ins. Page 6 of 7 11-12-2008
Rough-In Dimensions for Drain and Supplies Type H Drain Centrally rising vent with supplies from below Through Floor: Stub up 3" (76) (Optional) 1/2" NPT Supplies 5" (127) 36: 54: 9-1/4" (235) 2-3/4" (70) 1-1/2" NPT Vent from Above 4-1/2" (114) 4-1/2" (114) Centerline of Washfountain 1/2" NPT Supplies Through Floor: Stub up 2-1/2" (64) (Optional) Vent from Above Type O Drain Off-line vent with supplies from above Through Floor: Stub up 3" (76) (Optional) 2-3/4" (70) 1/2" Nom. Copper Tube Supplies from Above Must Be Located on These Centers to Pass Through Washfountain Shroud and Sprayhead 5" (127) 36: 7-9/16" (192) 54: 8-1/16" (205) Centerline of Washfountain 1/2" NPT Supplies from Above Through Wall: Stub out to Suit Trap 1/2" NPT Supplies Supplies and Drain Through Floor (Optional) ** Through Wall: Stub out to Suit Trap Drain Through Floor (Optional) ** Std: 12" (305) Juv: ** Floor Mounted Units Only Type H Drain Supplies below Centrally-rising vent P-Trap furnished Type O Drain Supplies above Off-drain vent P-Trap furnished by others Rough-In Notes 1. Maximum flow rate required to washfountain is 1.5 GPM for Models SN2003 and SN2023 or 2.0 GPM for Model SN2004 and SN2024. Size supply lines accordingly. 2. Unit with "O" drain and paper towel dispensers and/or a shroud, should use "B" drain Rough-Ins. Page 7 of 7