SUBMITTAL. Project. CLU Swenson Center. Date 01/07/2010. Mechanical Contractor. West Coast Air Conditioning. Mechanical Engineer

SUBMITTAL Project CLU Swenson Center Date 01/07/2010 Mechanical Contractor West Coast Air Conditioning Mechanical Engineer J & S Consulting Engineers, Inc. Revision Notes RTU-101, 102, 103, 201, 202, 203, 204, 205, 206 no changes made. Clarifications are listed below. The Carrier control system provides demand control ventilation and vvt controls. All rooftop units include Carrier s humidimizer system which noted on the unit report for each rooftop unit. All rooftop units include differential enthalpy economizers. The rooftop Comfortlink controller uses the inputs from two enthalpy sensors to achieve differential enthalpy control. Each unit report will show an economizer with a single enthalpy sensor, and an accessory return air enthalpy sensor which must be field installed and connected to the Comfortlink controller. All rooftop units include power exhaust as noted on the unit report for each rooftop unit.

Table Of Contents RTU-101 102 202...3 Unit Report...4 Certified Drawing...5 Performance Summary...6 Unit Feature Sheet...8 Spec Sheet...9 RTU-103 204...10 Unit Report...11 Certified Drawing...12 Performance Summary...13 Unit Feature Sheet...15 Spec Sheet...16 RTU-201 203...17 Unit Report...18 Certified Drawing...19 Performance Summary...20 Unit Feature Sheet...22 Spec Sheet...23 RTU-205...24 Unit Report...25 Certified Drawing...26 Performance Summary...27 Unit Feature Sheet...29 Spec Sheet...30 RTU-206...31 Unit Report...32 Certified Drawing...33 Performance Summary...34 Unit Feature Sheet...36 Spec Sheet...37 Packaged Rooftop Builder 1.19k Page 2 of 37

RTU-101 102 202 RTU-101 102 202 RTU-101 102 202 Tag Cover Sheet Unit Report Certified Drawing Performance Report Unit Feature Sheet Spec Sheet Packaged Rooftop Builder 1.19k Page 3 of 37

Unit R eport Unit Report For RTU-101 102 202 Unit Parameters Unit Model:...48PGLC08-AJ6--B1 Unit Size:...08 (7.5 Tons) Volts-Phase-Hertz:... 460-3-60 Heating Type:...Gas Duct Cfg:Vertical Supply/Vertical Return (Factory Standard) Heating Capacity: Low Heat w/ Stainless Steel HX (inc. Low NOx on 2-5 Tons) Dimensions (ft. in.) & Weight (lb.) *** Unit Length:... 8' 7'' Unit Width:... 5' 3'' Unit Height:... 4' 4'' Base Unit Weight:...1217 lb *** Weights and Dimensions are approximate. Weight does not include roof curbs, unit packaging, field installed accessories or factory installed options. Approximate dimensions are provided primarily for shipping purposes. For exact dimensions and weights, refer to appropriate product data catalog. Lines and Filters Gas Line Size:... 3/4 in. Condensate Drain Line Size:... 3/4 in. Return Air Filter Type:...Throwaway Return Air Filter Quantity:... 4 Return Air Filter Size:... 20x25x2 Unit Configuration ComfortLink Controls with Visual Scrolling Marquee Display Low Range Motor / Drive with Vertical SA/RA Al/Cu Cond and Evap and Humidi-MiZer Standard - No EnergyX Int. Gear Driven Eco. w/ Outdoor Single Enthalpy Sensor Power Exhaust Warranty Information First Year - Parts Only (Standard) No optional warranties were selected. NOTE: Please see Warranty Catalog 500-089 for explanation of policies and ordering methods. Ordering Information Part Number Description Quantity 48PGLC08-AJ6--B1 Rooftop Unit 3 Base Unit ComfortLink Controls with Visual Scrolling Marquee Display Low Range Motor / Drive with Vertical SA/RA Al/Cu Cond and Evap and Humidi-MiZer Standard - No EnergyX Int. Gear Driven Eco. w/ Outdoor Single Enthalpy Sensor Power Exhaust Accessories CRENTDIF002A00 Return Air Enthalpy Sensor 3 Packaged Rooftop Builder 1.19k Page 4 of 37

Certified Dr awing Certified Drawing for RTU-101 102 202 Packaged Rooftop Builder 1.19k Page 5 of 37

Perfor mance Summar y Performance Summary For RTU-101 102 202 Part Number:48PGLC08-AJ6--B1 ARI EER:...12.50 IPLV (Max Cooling at Normal Cooling Design Mode):...13.3 Base Unit Weight:...1217 lb Base Unit Dimensions Unit Length:...102.6 in Unit Width:...63.2 in Unit Height:...52.1 in Unit Voltage-Phase-Hertz:...460-3-60 Air Discharge:... Vertical Fan Drive Type:... Belt Actual Airflow:...3000 CFM Site Altitude:...0 ft Cooling Performance Condenser Entering Air DB:...95.0 F Evaporator Entering Air DB:...80.0 F Evaporator Entering Air WB:...67.0 F Entering Air Enthalpy:...31.44 BTU/lb Evaporator Leaving Air DB:...58.1 F Evaporator Leaving Air WB:...57.5 F Evaporator Leaving Air Enthalpy:...24.72 BTU/lb Gross Cooling Capacity:...90.70 MBH Gross Sensible Capacity:...70.80 MBH Compressor Power Input:...5.71 kw Coil Bypass Factor:...0.160 Heating Performance Heating Airflow:...3000 CFM Entering Air Temp:...70.0 F Leaving Air Temp:...104.4 F Gas Input Capacity:... 95.2 / 136.0 MBH Gas Heating Capacity:... 111.50 MBH Temperature Rise:...34.4 F NOTE:... Second Stage Supply Fan External Static Pressure:...0.60 in wg Options / Accessories Static Pressure Economiser:...0.07 in wg Humidi-MiZer (tm) Dehumidification System:...0.04 in wg Power Exhaust:...(Fan Data Includes Drop) Total External Static:...0.72 in wg Fan RPM:...696 Fan Power:...1.02 BHP NOTE:... Low Range Fan Option Power Exhaust Return Duct Static:...0.20 in wg Max. Air To Exhaust:...3850 CFM Electrical Data Compressor #1 RLA:...6.4 Compressor #1 LRA:...39 Compressor #2 RLA:...6.4 Compressor #2 LRA:...39 Outdoor Fan Motor Qty:...2 Outdoor Fan FLA (ea):...0.8 Indoor Fan Motor Type:...Low Indoor Fan Motor FLA:...2.6 Combustion Fan Motor FLA (ea):...0.3 Pwr. Exhaust Fan Motor FLA:...1.2 Power Supply MCA:...19.8 Power Supply MOCP (Fuse or HACR):...25 Min. Unit Disconnect FLA:...21 Min. Unit Disconnect LRA:...100 Electrical Convenience Outlet:...None Voltage Range:...414-506 Acoustics Sound Rating:...80.0 db Sound Power Levels, db re 10E-12 Watts Discharge Inlet Outdoor 63 Hz 84.1 80.7 91.7 125 Hz 80.4 73.0 83.6 250 Hz 71.8 68.7 81.0 500 Hz 70.2 62.7 77.9 1000 Hz 65.0 56.7 75.0 2000 Hz 61.6 52.8 69.9 4000 Hz 62.4 52.4 66.0 8000 Hz 56.6 49.2 59.3 A-Weighted 72.6 65.7 80.0 Packaged Rooftop Builder 1.19k Page 6 of 37

Performance Summary For RTU-101 102 202 2.0 1000 RPM Fan Curve 100% 3.00 BHP 900 RPM 1.5 800 RPM Static Pressure (in. wg.) 1.0 700 RPM 600 RPM RP SC 2.00 BHP 500 RPM 0.5 400 RPM 1.50 BHP 300 RPM 0.50 BHP 0.75 BHP 1.00 BHP 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Airflow (CFM - thousands) RPM = 696 BHP = 1.02 Maximum RPM = 1600 Maximum HP = 3.70 SC - System Curve RP - Rated Point Packaged Rooftop Builder 1.19k Page 7 of 37

Unit Featur e Sheet Unit Feature Sheet for RTU-101 102 202-48PG PACKAGED ROOFTOP GAS HEATING/ELECTRIC COOLING UNITS 2, 3, 4, 5, 6, 7.5, 8.5, 10, 12.5, 15, 18, 20, 25 TONS STANDARD FEATURES INCLUDE: Puron (R-410A) HFC refrigerant SEER's up to 14.8, EER's up to 12.5, IPLV's up to 13.3 ARI certified outdoor sound levels as low as 72 db Scroll compressors with crankcase heaters, internal line break overload and high-pressure protection Single compressors, single stage cooling on 03-07 models Dual compressors, dual stage cooling on 08-28 models TXV refrigerant metering system on each circuit High Pressure, Low Pressure/Loss of charge, and Freeze protection. Solid core liquid line filter drier on each circuit. Ambient cooling operation from 0 F up to 125 F (DDC controls) and from 40 F up to 125 F (Electro-mechanical controls) Foil faced insulation throughout entire unit Pre-painted exterior panels and primer-coated interior panels tested to 500 hours ASTM B117 (scribed specimen)salt spray protection Internally sloped condensate pan conforms to ASHRAE 62 standards High performance belt drive indoor fan assemblies Internally protected, shaft down totally enclosed condenser motors 2 inch filter standard, field convertible to 4 inch capability 24 volt control system with resettable circuit breakers Induced draft combustion Redundant gas valves with up to two stages of heating Models 48PG 03-28 are E NERGY STAR qualified CENTURION SERIES 48PG units are single piece packaged ultra high efficiency electric cooling with gas heating rooftops. They provide ultra high operating efficiencies, ease of maintenance, ease of installation, and reliability. Units come pre-wired and precharged with PURON (R410A) environmental friendly refrigerant at the factory. Units are factory tested in both heating and cooling modes. Units are rated in accordance with ARI Standard 210 (03-06 sizes) and 360 (07-28 sizes). Tested in accordance with UL Standard 1995 and listed with UL and UL Canada. Approved and certified by: Sizes 03-06 Size 07-28 Certified to ISO 9001:2000 STANDARD WARRANTY: 10-year standard heat exchanger 15-year stainless steel heat exchanger 5-year compressor 1-year parts Many optional upgrades also available MAINTENANCE FEATURES: Single slab, single pass evaporator and condenser coils with dual side access panels facilitate easy cleaning for maintained high efficiencies Hinged access doors with, quick turn latches and door retainers Slide out Indoor fan assembly for added service convenience Dedicated, fully insulated compressor compartment Slide out condensate pan (03-16 models) Permanently lubricated evaporator, condenser and inducer motors INSTALLATION FEATURES: Thru the bottom and side electrical and gas connection capabilities Weather tight thru the bottom access plate Single point electrical and gas connections Return and supply duct fits between 24" on center joist (03-12 models) Field convertible from vertical to horizontal airflow (03-16 models) Single piece outdoor air hoods Full perimeter baserail with built-in rigging adapters and fork truck slots FACTORY INSTALLED OPTIONS INCLUDE: ComfortLINK Direct Digital Controls (DDC) Exclusive Humidi-MiZer adaptive dehumidification system Exclusive EnergyX Energy Recovery module Supply and/or return air smoke detectors Powered or non-powered 115 volt convenience outlet Non-fused disconnect switch or circuit breaker (HACR) Dry bulb or enthalpy economizer with or without return air CO2 sensor Manual outdoor air damper Two position motorized outdoor damper Barometric relief damper Power Exhaust Condenser coil guard MERV-8 Pleated filter upgrade Fan status and filter status switches Side-by-side horizontal ducts (sizes 20-28. Std all other models) High static indoor fan and drive systems Phase loss and compressor reverse rotation protection Corrosion resistant options for evaporator and condenser coils Stainless steel gas heat exchanger Low NOx models that meet California Air Quality Management specs For a complete list of options and accessories refer to the Product Data Catalog for this unit. Packaged Rooftop Builder 1.19k Page 8 of 37

Spec Sheet Spec Sheet for RTU-101 102 202 Humidi-MiZer Adaptive Dehumidification System Specification Sheet For Factory Installed Humidi-MiZer systems on 2-25 ton Commercial Rooftop Units APPLICABLE UNITS: 48/50PG, PM 03-28 48/50TC 03-28 48/50HE 003-006 48/50HJ 004-014 GENERAL DATA The Carrier Humidi-MiZer Adaptive Dehumidification system is an all-inclusive factory-installed option, available on Carrier's 2-25 ton unitary rooftop units. It is a cost effective, yet flexible and high performing solution to high humidity and part-load issues for packaged rooftop applications. The system expands the unit's envelope of operation by providing significantly more stages of unit Sensible Heat Ratio (SHR) based on the space temperature and humidity demand. SYSTEM SUMMARY The Humidi-MiZer Adaptive Dehumidification system utilizes a condenser reheat coil, on all refrigerant circuits, located in the airflow path directly downstream from the evaporator. When activated, the refrigerant flows through the condenser, through the Humidi-MiZer coil and then through the evaporator. A condenser bypass line allows hot refrigerant gas to bypass the condenser and vary the refrigerant temperature before it enters the Humidi-MiZer coil. See Figure 1. The location of the coil and the refrigerant flow path allow the refrigerant to be significantly subcooled and the indoor air to be partially reheated for part-load applications or fully reheated for dehumidification only applications. If normal unit operation is required the Humidi-MiZer coil is deactivated. In a two circuit unit, the circuits can be operated independently of each other, allowing a wide range of unit performance and SHR's. SYSTEM FEATURES The Humidi-MiZer Adaptive Dehumidification system features: Reheat coil on all refrigerant circuits in the unit; provides up to 5 additional steps of unit capacity and operation Each circuit in the unit is capable of 3 modes of operation: o Normal - demand for cooling only. Conventional circuit operation and unit leaving air temperatures. o Sub-cooling - demand for space cooling and dehumidification. Unit supply air temperature is approximately 5-7 o F higher than normal supply air temperatures. Allows a conditioned space that is cooled and significantly more dehumidified, but not over-cooled. o ReHeat - demand for space dehumidification only. Unit supply air temperature is neutral (~72-75 but dehumidified. Integrated operation with optional economizer for increased modes of operation and unit flexibility Up to 35% more moisture removal than typical conventional Hot Gas ReHeat systems Unit mode of operation controlled automatically by space temperature and humidity sensors/stats o F) HGSV (Hot Gas Solenoid Valve) Condenser Coil Outdoor Air Humidi-MiZer coil Evaporator Coil Indoor Air LLSV (Liquid Line Solenoid Valve) Fig. 1 - Humidi-MiZer Adaptive Dehumidification System (single circuit unit shown) 1/1 11/1/2008 Packaged Rooftop Builder 1.19k Page 9 of 37

RTU-103 204 RTU-103 204 RTU-103 204 Tag Cover Sheet Unit Report Certified Drawing Performance Report Unit Feature Sheet Spec Sheet Packaged Rooftop Builder 1.19k Page 10 of 37

Unit R eport Unit Report For RTU-103 204 Unit Parameters Unit Model:...48PGLC09-AJ6--B1 Unit Size:...09 (8.5 Tons) Volts-Phase-Hertz:... 460-3-60 Heating Type:...Gas Duct Cfg:Vertical Supply/Vertical Return (Factory Standard) Heating Capacity: Low Heat w/ Stainless Steel HX (inc. Low NOx on 2-5 Tons) Dimensions (ft. in.) & Weight (lb.) *** Unit Length:... 8' 7'' Unit Width:... 5' 3'' Unit Height:... 4' 4'' Base Unit Weight:...1224 lb *** Weights and Dimensions are approximate. Weight does not include roof curbs, unit packaging, field installed accessories or factory installed options. Approximate dimensions are provided primarily for shipping purposes. For exact dimensions and weights, refer to appropriate product data catalog. Lines and Filters Gas Line Size:... 3/4 in. Condensate Drain Line Size:... 3/4 in. Return Air Filter Type:... Thowaway Return Air Filter Quantity:... 4 Return Air Filter Size:... 20x25x2 Unit Configuration ComfortLink Controls with Visual Scrolling Marquee Display Low Range Motor / Drive with Vertical SA/RA Al/Cu Cond and Evap and Humidi-MiZer Standard - No EnergyX Int. Gear Driven Eco. w/ Outdoor Single Enthalpy Sensor Power Exhaust Warranty Information First Year - Parts Only (Standard) No optional warranties were selected. NOTE: Please see Warranty Catalog 500-089 for explanation of policies and ordering methods. Ordering Information Part Number Description Quantity 48PGLC09-AJ6--B1 Rooftop Unit 2 Base Unit ComfortLink Controls with Visual Scrolling Marquee Display Low Range Motor / Drive with Vertical SA/RA Al/Cu Cond and Evap and Humidi-MiZer Standard - No EnergyX Int. Gear Driven Eco. w/ Outdoor Single Enthalpy Sensor Power Exhaust Accessories CRENTDIF002A00 Return Air Enthalpy Sensor 2 Packaged Rooftop Builder 1.19k Page 11 of 37

Certified Dr awing Certified Drawing for RTU-103 204 Packaged Rooftop Builder 1.19k Page 12 of 37

Perfor mance Summar y Performance Summary For RTU-103 204 Part Number:48PGLC09-AJ6--B1 ARI EER:...12.20 IPLV (Max Cooling at Normal Cooling Design Mode):...13.3 Base Unit Weight:...1224 lb Base Unit Dimensions Unit Length:...102.6 in Unit Width:...63.2 in Unit Height:...52.1 in Unit Voltage-Phase-Hertz:...460-3-60 Air Discharge:... Vertical Fan Drive Type:... Belt Actual Airflow:...3400 CFM Site Altitude:...0 ft Cooling Performance Condenser Entering Air DB:...95.0 F Evaporator Entering Air DB:...80.0 F Evaporator Entering Air WB:...67.0 F Entering Air Enthalpy:...31.44 BTU/lb Evaporator Leaving Air DB:...58.8 F Evaporator Leaving Air WB:...57.1 F Evaporator Leaving Air Enthalpy:...24.42 BTU/lb Gross Cooling Capacity:... 107.30 MBH Gross Sensible Capacity:...77.70 MBH Compressor Power Input:...6.96 kw Coil Bypass Factor:...0.190 Heating Performance Heating Airflow:...3400 CFM Entering Air Temp:...70.0 F Leaving Air Temp:...100.4 F Gas Input Capacity:... 95.2 / 136.0 MBH Gas Heating Capacity:... 111.50 MBH Temperature Rise:...30.4 F NOTE:... Second Stage Supply Fan External Static Pressure:...0.60 in wg Options / Accessories Static Pressure Economiser:...0.09 in wg Humidi-MiZer (tm) Dehumidification System:...0.05 in wg Power Exhaust:...(Fan Data Includes Drop) Total External Static:...0.74 in wg Fan RPM:...741 Fan Power:...1.33 BHP NOTE:... Low Range Fan Option Power Exhaust Return Duct Static:...0.20 in wg Max. Air To Exhaust:...3850 CFM Electrical Data Compressor #1 RLA:...7.1 Compressor #1 LRA:...46 Compressor #2 RLA:...7.1 Compressor #2 LRA:...46 Outdoor Fan Motor Qty:...2 Outdoor Fan FLA (ea):...0.8 Indoor Fan Motor Type:...Low Indoor Fan Motor FLA:...2.6 Combustion Fan Motor FLA (ea):...0.3 Pwr. Exhaust Fan Motor FLA:...1.2 Power Supply MCA:...21.4 Power Supply MOCP (Fuse or HACR):...25 Min. Unit Disconnect FLA:...23 Min. Unit Disconnect LRA:...114 Electrical Convenience Outlet:...None Voltage Range:...414-506 Acoustics Sound Rating:...80.0 db Sound Power Levels, db re 10E-12 Watts Discharge Inlet Outdoor 63 Hz 84.8 81.0 89.1 125 Hz 81.9 73.7 82.7 250 Hz 73.6 69.2 80.0 500 Hz 72.1 63.2 77.7 1000 Hz 67.2 57.8 75.0 2000 Hz 64.0 54.9 70.2 4000 Hz 65.5 55.0 66.3 8000 Hz 59.1 50.3 57.8 A-Weighted 74.6 66.5 80.0 Packaged Rooftop Builder 1.19k Page 13 of 37

Performance Summary For RTU-103 204 2.0 Fan Curve 1000 RPM 100% 1100 RPM 900 RPM 1.5 800 RPM Static Pressure (in. wg.) 1.0 700 RPM 600 RPM RP SC 3.70 BHP 0.5 500 RPM 2.00 BHP 3.00 BHP 400 RPM 1.50 BHP 300 RPM 0.75 BHP 0.50 BHP 1.00 BHP 0.0 0 1 2 3 4 5 Airflow (CFM - thousands) RPM = 741 BHP = 1.33 Maximum RPM = 1600 Maximum HP = 3.70 SC - System Curve RP - Rated Point Packaged Rooftop Builder 1.19k Page 14 of 37

Unit Featur e Sheet Unit Feature Sheet for RTU-103 204-48PG PACKAGED ROOFTOP GAS HEATING/ELECTRIC COOLING UNITS 2, 3, 4, 5, 6, 7.5, 8.5, 10, 12.5, 15, 18, 20, 25 TONS STANDARD FEATURES INCLUDE: Puron (R-410A) HFC refrigerant SEER's up to 14.8, EER's up to 12.5, IPLV's up to 13.3 ARI certified outdoor sound levels as low as 72 db Scroll compressors with crankcase heaters, internal line break overload and high-pressure protection Single compressors, single stage cooling on 03-07 models Dual compressors, dual stage cooling on 08-28 models TXV refrigerant metering system on each circuit High Pressure, Low Pressure/Loss of charge, and Freeze protection. Solid core liquid line filter drier on each circuit. Ambient cooling operation from 0 F up to 125 F (DDC controls) and from 40 F up to 125 F (Electro-mechanical controls) Foil faced insulation throughout entire unit Pre-painted exterior panels and primer-coated interior panels tested to 500 hours ASTM B117 (scribed specimen)salt spray protection Internally sloped condensate pan conforms to ASHRAE 62 standards High performance belt drive indoor fan assemblies Internally protected, shaft down totally enclosed condenser motors 2 inch filter standard, field convertible to 4 inch capability 24 volt control system with resettable circuit breakers Induced draft combustion Redundant gas valves with up to two stages of heating Models 48PG 03-28 are E NERGY STAR qualified CENTURION SERIES 48PG units are single piece packaged ultra high efficiency electric cooling with gas heating rooftops. They provide ultra high operating efficiencies, ease of maintenance, ease of installation, and reliability. Units come pre-wired and precharged with PURON (R410A) environmental friendly refrigerant at the factory. Units are factory tested in both heating and cooling modes. Units are rated in accordance with ARI Standard 210 (03-06 sizes) and 360 (07-28 sizes). Tested in accordance with UL Standard 1995 and listed with UL and UL Canada. Approved and certified by: Sizes 03-06 Size 07-28 Certified to ISO 9001:2000 STANDARD WARRANTY: 10-year standard heat exchanger 15-year stainless steel heat exchanger 5-year compressor 1-year parts Many optional upgrades also available MAINTENANCE FEATURES: Single slab, single pass evaporator and condenser coils with dual side access panels facilitate easy cleaning for maintained high efficiencies Hinged access doors with, quick turn latches and door retainers Slide out Indoor fan assembly for added service convenience Dedicated, fully insulated compressor compartment Slide out condensate pan (03-16 models) Permanently lubricated evaporator, condenser and inducer motors INSTALLATION FEATURES: Thru the bottom and side electrical and gas connection capabilities Weather tight thru the bottom access plate Single point electrical and gas connections Return and supply duct fits between 24" on center joist (03-12 models) Field convertible from vertical to horizontal airflow (03-16 models) Single piece outdoor air hoods Full perimeter baserail with built-in rigging adapters and fork truck slots FACTORY INSTALLED OPTIONS INCLUDE: ComfortLINK Direct Digital Controls (DDC) Exclusive Humidi-MiZer adaptive dehumidification system Exclusive EnergyX Energy Recovery module Supply and/or return air smoke detectors Powered or non-powered 115 volt convenience outlet Non-fused disconnect switch or circuit breaker (HACR) Dry bulb or enthalpy economizer with or without return air CO2 sensor Manual outdoor air damper Two position motorized outdoor damper Barometric relief damper Power Exhaust Condenser coil guard MERV-8 Pleated filter upgrade Fan status and filter status switches Side-by-side horizontal ducts (sizes 20-28. Std all other models) High static indoor fan and drive systems Phase loss and compressor reverse rotation protection Corrosion resistant options for evaporator and condenser coils Stainless steel gas heat exchanger Low NOx models that meet California Air Quality Management specs For a complete list of options and accessories refer to the Product Data Catalog for this unit. Packaged Rooftop Builder 1.19k Page 15 of 37

Spec Sheet Spec Sheet for RTU-103 204 Humidi-MiZer Adaptive Dehumidification System Specification Sheet For Factory Installed Humidi-MiZer systems on 2-25 ton Commercial Rooftop Units APPLICABLE UNITS: 48/50PG, PM 03-28 48/50TC 03-28 48/50HE 003-006 48/50HJ 004-014 GENERAL DATA The Carrier Humidi-MiZer Adaptive Dehumidification system is an all-inclusive factory-installed option, available on Carrier's 2-25 ton unitary rooftop units. It is a cost effective, yet flexible and high performing solution to high humidity and part-load issues for packaged rooftop applications. The system expands the unit's envelope of operation by providing significantly more stages of unit Sensible Heat Ratio (SHR) based on the space temperature and humidity demand. SYSTEM SUMMARY The Humidi-MiZer Adaptive Dehumidification system utilizes a condenser reheat coil, on all refrigerant circuits, located in the airflow path directly downstream from the evaporator. When activated, the refrigerant flows through the condenser, through the Humidi-MiZer coil and then through the evaporator. A condenser bypass line allows hot refrigerant gas to bypass the condenser and vary the refrigerant temperature before it enters the Humidi-MiZer coil. See Figure 1. The location of the coil and the refrigerant flow path allow the refrigerant to be significantly subcooled and the indoor air to be partially reheated for part-load applications or fully reheated for dehumidification only applications. If normal unit operation is required the Humidi-MiZer coil is deactivated. In a two circuit unit, the circuits can be operated independently of each other, allowing a wide range of unit performance and SHR's. SYSTEM FEATURES The Humidi-MiZer Adaptive Dehumidification system features: Reheat coil on all refrigerant circuits in the unit; provides up to 5 additional steps of unit capacity and operation Each circuit in the unit is capable of 3 modes of operation: o Normal - demand for cooling only. Conventional circuit operation and unit leaving air temperatures. o Sub-cooling - demand for space cooling and dehumidification. Unit supply air temperature is approximately 5-7 o F higher than normal supply air temperatures. Allows a conditioned space that is cooled and significantly more dehumidified, but not over-cooled. o ReHeat - demand for space dehumidification only. Unit supply air temperature is neutral (~72-75 but dehumidified. Integrated operation with optional economizer for increased modes of operation and unit flexibility Up to 35% more moisture removal than typical conventional Hot Gas ReHeat systems Unit mode of operation controlled automatically by space temperature and humidity sensors/stats o F) HGSV (Hot Gas Solenoid Valve) Condenser Coil Outdoor Air Humidi-MiZer coil Evaporator Coil Indoor Air LLSV (Liquid Line Solenoid Valve) Fig. 1 - Humidi-MiZer Adaptive Dehumidification System (single circuit unit shown) 1/1 11/1/2008 Packaged Rooftop Builder 1.19k Page 16 of 37

RTU-201 203 RTU-201 203 RTU-201 203 Tag Cover Sheet Unit Report Certified Drawing Performance Report Unit Feature Sheet Spec Sheet Packaged Rooftop Builder 1.19k Page 17 of 37

Unit R eport Unit Report For RTU-201 203 Unit Parameters Unit Model:...48PGLC12-AJ6--B1 Unit Size:...12 (10 Tons) Volts-Phase-Hertz:... 460-3-60 Heating Type:...Gas Duct Cfg:Vertical Supply/Vertical Return (Factory Standard) Heating Capacity: Low Heat w/ Stainless Steel HX (inc. Low NOx on 2-5 Tons) Dimensions (ft. in.) & Weight (lb.) *** Unit Length:... 8' 7'' Unit Width:... 5' 3'' Unit Height:... 4' 4'' Base Unit Weight:...1324 lb *** Weights and Dimensions are approximate. Weight does not include roof curbs, unit packaging, field installed accessories or factory installed options. Approximate dimensions are provided primarily for shipping purposes. For exact dimensions and weights, refer to appropriate product data catalog. Lines and Filters Gas Line Size:... 3/4 in. Condensate Drain Line Size:... 3/4 in. Return Air Filter Type:...Throwaway Return Air Filter Quantity:... 4 Return Air Filter Size:... 20x25x2 Unit Configuration ComfortLink Controls with Visual Scrolling Marquee Display Low Range Motor / Drive with Vertical SA/RA Al/Cu Cond and Evap and Humidi-MiZer Standard - No EnergyX Int. Gear Driven Eco. w/ Outdoor Single Enthalpy Sensor Power Exhaust Warranty Information First Year - Parts Only (Standard) No optional warranties were selected. NOTE: Please see Warranty Catalog 500-089 for explanation of policies and ordering methods. Ordering Information Part Number Description Quantity 48PGLC12-AJ6--B1 Rooftop Unit 2 Base Unit ComfortLink Controls with Visual Scrolling Marquee Display Low Range Motor / Drive with Vertical SA/RA Al/Cu Cond and Evap and Humidi-MiZer Standard - No EnergyX Int. Gear Driven Eco. w/ Outdoor Single Enthalpy Sensor Power Exhaust Accessories CRENTDIF002A00 Return Air Enthalpy Sensor 2 Packaged Rooftop Builder 1.19k Page 18 of 37

Certified Dr awing Certified Drawing for RTU-201 203 Packaged Rooftop Builder 1.19k Page 19 of 37

Perfor mance Summar y Performance Summary For RTU-201 203 Part Number:48PGLC12-AJ6--B1 ARI EER:...12.00 IPLV (Max Cooling at Normal Cooling Design Mode):...13.1 Base Unit Weight:...1324 lb Base Unit Dimensions Unit Length:...102.6 in Unit Width:...63.2 in Unit Height:...52.1 in Unit Voltage-Phase-Hertz:...460-3-60 Air Discharge:... Vertical Fan Drive Type:... Belt Actual Airflow:...4000 CFM Site Altitude:...0 ft Cooling Performance Condenser Entering Air DB:...95.0 F Evaporator Entering Air DB:...80.0 F Evaporator Entering Air WB:...67.0 F Entering Air Enthalpy:...31.44 BTU/lb Evaporator Leaving Air DB:...57.9 F Evaporator Leaving Air WB:...57.1 F Evaporator Leaving Air Enthalpy:...24.46 BTU/lb Gross Cooling Capacity:... 125.60 MBH Gross Sensible Capacity:...95.30 MBH Compressor Power Input:...8.16 kw Coil Bypass Factor:...0.080 Heating Performance Heating Airflow:...4000 CFM Entering Air Temp:...70.0 F Leaving Air Temp:...104.4 F Gas Input Capacity:... 126.7 / 181.0 MBH Gas Heating Capacity:... 148.40 MBH Temperature Rise:...34.4 F NOTE:... Second Stage Supply Fan External Static Pressure:...0.60 in wg Options / Accessories Static Pressure Economiser:...0.11 in wg Humidi-MiZer (tm) Dehumidification System:...0.06 in wg Power Exhaust:...(Fan Data Includes Drop) Total External Static:...0.77 in wg Fan RPM:...839 Fan Power:...2.03 BHP NOTE:... Low Range Fan Option Power Exhaust Return Duct Static:...0.20 in wg Max. Air To Exhaust:...3850 CFM Electrical Data Compressor #1 RLA:...9.6 Compressor #1 LRA:...62 Compressor #2 RLA:...9.6 Compressor #2 LRA:...62 Outdoor Fan Motor Qty:...2 Outdoor Fan FLA (ea):...1 Indoor Fan Motor Type:...Low Indoor Fan Motor FLA:...3.4 Combustion Fan Motor FLA (ea):...0.3 Pwr. Exhaust Fan Motor FLA:...1.2 Power Supply MCA:...28.2 Power Supply MOCP (Fuse or HACR):...35 Min. Unit Disconnect FLA:...30 Min. Unit Disconnect LRA:...159 Electrical Convenience Outlet:...None Voltage Range:...414-506 Acoustics Sound Rating:...80.0 db Sound Power Levels, db re 10E-12 Watts Discharge Inlet Outdoor 63 Hz 86.5 81.9 90.4 125 Hz 84.6 75.4 83.1 250 Hz 77.1 70.3 80.9 500 Hz 75.4 64.3 77.8 1000 Hz 71.0 60.2 75.2 2000 Hz 67.8 58.3 70.0 4000 Hz 69.9 59.0 66.1 8000 Hz 63.6 53.0 57.6 A-Weighted 78.2 68.5 80.0 Packaged Rooftop Builder 1.19k Page 20 of 37

Performance Summary For RTU-201 203 2.0 Fan Curve 1000 RPM 100% 1100 RPM 1200 RPM 900 RPM 1.5 800 RPM Static Pressure (in. wg.) 1.0 700 RPM 600 RPM RP SC 0.5 500 RPM 5.00 BHP 400 RPM 300 RPM 0.50 BHP 0.75 BHP 1.50 BHP 2.00 BHP 3.00 BHP 0.0 1.00 BHP 0 1 2 3 4 5 6 Airflow (CFM - thousands) RPM = 839 BHP = 2.03 Maximum RPM = 1600 Maximum HP = 3.70 SC - System Curve RP - Rated Point Packaged Rooftop Builder 1.19k Page 21 of 37

Unit Featur e Sheet Unit Feature Sheet for RTU-201 203-48PG PACKAGED ROOFTOP GAS HEATING/ELECTRIC COOLING UNITS 2, 3, 4, 5, 6, 7.5, 8.5, 10, 12.5, 15, 18, 20, 25 TONS STANDARD FEATURES INCLUDE: Puron (R-410A) HFC refrigerant SEER's up to 14.8, EER's up to 12.5, IPLV's up to 13.3 ARI certified outdoor sound levels as low as 72 db Scroll compressors with crankcase heaters, internal line break overload and high-pressure protection Single compressors, single stage cooling on 03-07 models Dual compressors, dual stage cooling on 08-28 models TXV refrigerant metering system on each circuit High Pressure, Low Pressure/Loss of charge, and Freeze protection. Solid core liquid line filter drier on each circuit. Ambient cooling operation from 0 F up to 125 F (DDC controls) and from 40 F up to 125 F (Electro-mechanical controls) Foil faced insulation throughout entire unit Pre-painted exterior panels and primer-coated interior panels tested to 500 hours ASTM B117 (scribed specimen)salt spray protection Internally sloped condensate pan conforms to ASHRAE 62 standards High performance belt drive indoor fan assemblies Internally protected, shaft down totally enclosed condenser motors 2 inch filter standard, field convertible to 4 inch capability 24 volt control system with resettable circuit breakers Induced draft combustion Redundant gas valves with up to two stages of heating Models 48PG 03-28 are E NERGY STAR qualified CENTURION SERIES 48PG units are single piece packaged ultra high efficiency electric cooling with gas heating rooftops. They provide ultra high operating efficiencies, ease of maintenance, ease of installation, and reliability. Units come pre-wired and precharged with PURON (R410A) environmental friendly refrigerant at the factory. Units are factory tested in both heating and cooling modes. Units are rated in accordance with ARI Standard 210 (03-06 sizes) and 360 (07-28 sizes). Tested in accordance with UL Standard 1995 and listed with UL and UL Canada. Approved and certified by: Sizes 03-06 Size 07-28 Certified to ISO 9001:2000 STANDARD WARRANTY: 10-year standard heat exchanger 15-year stainless steel heat exchanger 5-year compressor 1-year parts Many optional upgrades also available MAINTENANCE FEATURES: Single slab, single pass evaporator and condenser coils with dual side access panels facilitate easy cleaning for maintained high efficiencies Hinged access doors with, quick turn latches and door retainers Slide out Indoor fan assembly for added service convenience Dedicated, fully insulated compressor compartment Slide out condensate pan (03-16 models) Permanently lubricated evaporator, condenser and inducer motors INSTALLATION FEATURES: Thru the bottom and side electrical and gas connection capabilities Weather tight thru the bottom access plate Single point electrical and gas connections Return and supply duct fits between 24" on center joist (03-12 models) Field convertible from vertical to horizontal airflow (03-16 models) Single piece outdoor air hoods Full perimeter baserail with built-in rigging adapters and fork truck slots FACTORY INSTALLED OPTIONS INCLUDE: ComfortLINK Direct Digital Controls (DDC) Exclusive Humidi-MiZer adaptive dehumidification system Exclusive EnergyX Energy Recovery module Supply and/or return air smoke detectors Powered or non-powered 115 volt convenience outlet Non-fused disconnect switch or circuit breaker (HACR) Dry bulb or enthalpy economizer with or without return air CO2 sensor Manual outdoor air damper Two position motorized outdoor damper Barometric relief damper Power Exhaust Condenser coil guard MERV-8 Pleated filter upgrade Fan status and filter status switches Side-by-side horizontal ducts (sizes 20-28. Std all other models) High static indoor fan and drive systems Phase loss and compressor reverse rotation protection Corrosion resistant options for evaporator and condenser coils Stainless steel gas heat exchanger Low NOx models that meet California Air Quality Management specs For a complete list of options and accessories refer to the Product Data Catalog for this unit. Packaged Rooftop Builder 1.19k Page 22 of 37

Spec Sheet Spec Sheet for RTU-201 203 Humidi-MiZer Adaptive Dehumidification System Specification Sheet For Factory Installed Humidi-MiZer systems on 2-25 ton Commercial Rooftop Units APPLICABLE UNITS: 48/50PG, PM 03-28 48/50TC 03-28 48/50HE 003-006 48/50HJ 004-014 GENERAL DATA The Carrier Humidi-MiZer Adaptive Dehumidification system is an all-inclusive factory-installed option, available on Carrier's 2-25 ton unitary rooftop units. It is a cost effective, yet flexible and high performing solution to high humidity and part-load issues for packaged rooftop applications. The system expands the unit's envelope of operation by providing significantly more stages of unit Sensible Heat Ratio (SHR) based on the space temperature and humidity demand. SYSTEM SUMMARY The Humidi-MiZer Adaptive Dehumidification system utilizes a condenser reheat coil, on all refrigerant circuits, located in the airflow path directly downstream from the evaporator. When activated, the refrigerant flows through the condenser, through the Humidi-MiZer coil and then through the evaporator. A condenser bypass line allows hot refrigerant gas to bypass the condenser and vary the refrigerant temperature before it enters the Humidi-MiZer coil. See Figure 1. The location of the coil and the refrigerant flow path allow the refrigerant to be significantly subcooled and the indoor air to be partially reheated for part-load applications or fully reheated for dehumidification only applications. If normal unit operation is required the Humidi-MiZer coil is deactivated. In a two circuit unit, the circuits can be operated independently of each other, allowing a wide range of unit performance and SHR's. SYSTEM FEATURES The Humidi-MiZer Adaptive Dehumidification system features: Reheat coil on all refrigerant circuits in the unit; provides up to 5 additional steps of unit capacity and operation Each circuit in the unit is capable of 3 modes of operation: o Normal - demand for cooling only. Conventional circuit operation and unit leaving air temperatures. o Sub-cooling - demand for space cooling and dehumidification. Unit supply air temperature is approximately 5-7 o F higher than normal supply air temperatures. Allows a conditioned space that is cooled and significantly more dehumidified, but not over-cooled. o ReHeat - demand for space dehumidification only. Unit supply air temperature is neutral (~72-75 but dehumidified. Integrated operation with optional economizer for increased modes of operation and unit flexibility Up to 35% more moisture removal than typical conventional Hot Gas ReHeat systems Unit mode of operation controlled automatically by space temperature and humidity sensors/stats o F) HGSV (Hot Gas Solenoid Valve) Condenser Coil Outdoor Air Humidi-MiZer coil Evaporator Coil Indoor Air LLSV (Liquid Line Solenoid Valve) Fig. 1 - Humidi-MiZer Adaptive Dehumidification System (single circuit unit shown) 1/1 11/1/2008 Packaged Rooftop Builder 1.19k Page 23 of 37

RTU-205 RTU-205 RTU-205 Tag Cover Sheet Unit Report Certified Drawing Performance Report Unit Feature Sheet Spec Sheet Packaged Rooftop Builder 1.19k Page 24 of 37

Unit R eport Unit Report For RTU-205 Unit Parameters Unit Model:... 48PGNC03-AJ3--B1 Unit Size:...03 (2 Tons) Volts-Phase-Hertz:... 208-1-60 Heating Type:...Gas Duct Cfg:Vertical Supply/Vertical Return (Factory Standard) Heating Capacity: High Heat w/ Stainless Steel HX (inc. Low NOx on 2-5 Tons) Dimensions (ft. in.) & Weight (lb.) *** Unit Length:... 7' 6'' Unit Width:... 4' 6'' Unit Height:... 3' 8'' Base Unit Weight:...774 lb *** Weights and Dimensions are approximate. Weight does not include roof curbs, unit packaging, field installed accessories or factory installed options. Approximate dimensions are provided primarily for shipping purposes. For exact dimensions and weights, refer to appropriate product data catalog. Lines and Filters Gas Line Size:... 1/2 in. Condensate Drain Line Size:... 3/4 in. Return Air Filter Type:...Throwaway Return Air Filter Quantity:... 4 Return Air Filter Size:... 16x20x2 Unit Configuration ComfortLink Controls with Visual Scrolling Marquee Display Low Range Motor / Drive with Vertical SA/RA Al/Cu Cond and Evap and Humidi-MiZer Standard - No EnergyX Int. Gear Driven Eco. w/ Outdoor Single Enthalpy Sensor Power Exhaust Warranty Information First Year - Parts Only (Standard) No optional warranties were selected. NOTE: Please see Warranty Catalog 500-089 for explanation of policies and ordering methods. Ordering Information Part Number Description Quantity 48PGNC03-AJ3--B1 Rooftop Unit 1 Base Unit ComfortLink Controls with Visual Scrolling Marquee Display Low Range Motor / Drive with Vertical SA/RA Al/Cu Cond and Evap and Humidi-MiZer Standard - No EnergyX Int. Gear Driven Eco. w/ Outdoor Single Enthalpy Sensor Power Exhaust Accessories CRENTDIF002A00 Return Air Enthalpy Sensor 1 Packaged Rooftop Builder 1.19k Page 25 of 37

Certified Dr awing Certified Drawing for RTU-205 Packaged Rooftop Builder 1.19k Page 26 of 37

Perfor mance Summar y Performance Summary For RTU-205 Part Number:48PGNC03-AJ3--B1 ARI SEER:...14.00 Base Unit Weight:...774 lb Base Unit Dimensions Unit Length:...90.0 in Unit Width:...53.9 in Unit Height:...44.5 in Unit Voltage-Phase-Hertz:...208-1-60 Air Discharge:... Vertical Fan Drive Type:... Belt Actual Airflow:...800 CFM Site Altitude:...0 ft Cooling Performance Condenser Entering Air DB:...95.0 F Evaporator Entering Air DB:...80.0 F Evaporator Entering Air WB:...67.0 F Entering Air Enthalpy:...31.44 BTU/lb Evaporator Leaving Air DB:...59.3 F Evaporator Leaving Air WB:...57.2 F Evaporator Leaving Air Enthalpy:...24.52 BTU/lb Gross Cooling Capacity:...24.90 MBH Gross Sensible Capacity:...17.90 MBH Compressor Power Input:...1.65 kw Coil Bypass Factor:...0.150 Heating Performance Heating Airflow:...800 CFM Entering Air Temp:...70.0 F Leaving Air Temp:...115.6 F Gas Input Capacity:...51.0 MBH Gas Heating Capacity:...39.40 MBH Temperature Rise:...45.6 F Supply Fan External Static Pressure:...0.40 in wg Options / Accessories Static Pressure Economiser:...0.01 in wg Humidi-MiZer (tm) Dehumidification System:...0.02 in wg Power Exhaust:...(Fan Data Includes Drop) Total External Static:...0.43 in wg Fan RPM:...590 Fan Power:...0.15 BHP NOTE:... Low Range Fan Option Power Exhaust Return Duct Static:...0.20 in wg Max. Air To Exhaust:...1050 CFM Electrical Data Compressor #1 RLA:...12.8 Compressor #1 LRA:...60 Outdoor Fan Motor Qty:...1 Outdoor Fan FLA (ea):...1 Indoor Fan Motor Type:...Low Indoor Fan Motor FLA:...4.9 Combustion Fan Motor FLA (ea):...0.52 Pwr. Exhaust Fan Motor FLA:...1.4 Power Supply MCA:...23.3 Power Supply MOCP (Fuse or HACR):...30 Min. Unit Disconnect FLA:...23 Min. Unit Disconnect LRA:...76 Electrical Convenience Outlet:...None Voltage Range:...187-253 Acoustics Sound Rating:...75.0 db Sound Power Levels, db re 10E-12 Watts Discharge Inlet Outdoor 63 Hz 85.3 82.9 82.6 125 Hz 72.7 70.5 79.9 250 Hz 63.2 68.2 75.7 500 Hz 64.1 55.1 73.3 1000 Hz 56.4 46.3 70.0 2000 Hz 50.2 41.0 64.3 4000 Hz 47.4 41.5 58.4 8000 Hz 45.7 43.4 50.5 A-Weighted 65.4 62.8 75.0 Packaged Rooftop Builder 1.19k Page 27 of 37

Performance Summary For RTU-205 2.0 1100 RPM Fan Curve 1200 RPM 100% 1000 RPM 1.5 Static Pressure (in. wg.) 1.0 900 RPM 800 RPM 700 RPM 600 RPM SC 1.00 BHP 0.75 BHP 0.5 500 RPM RP 400 RPM 300 RPM 0.50 BHP 0.0 0.0 0.5 1.0 1.5 2.0 Airflow (CFM - thousands) RPM = 590 BHP = 0.15 Maximum RPM = 2000 Maximum HP = 1.00 SC - System Curve RP - Rated Point Packaged Rooftop Builder 1.19k Page 28 of 37

Unit Featur e Sheet Unit Feature Sheet for RTU-205-48PG PACKAGED ROOFTOP GAS HEATING/ELECTRIC COOLING UNITS 2, 3, 4, 5, 6, 7.5, 8.5, 10, 12.5, 15, 18, 20, 25 TONS STANDARD FEATURES INCLUDE: Puron (R-410A) HFC refrigerant SEER's up to 14.8, EER's up to 12.5, IPLV's up to 13.3 ARI certified outdoor sound levels as low as 72 db Scroll compressors with crankcase heaters, internal line break overload and high-pressure protection Single compressors, single stage cooling on 03-07 models Dual compressors, dual stage cooling on 08-28 models TXV refrigerant metering system on each circuit High Pressure, Low Pressure/Loss of charge, and Freeze protection. Solid core liquid line filter drier on each circuit. Ambient cooling operation from 0 F up to 125 F (DDC controls) and from 40 F up to 125 F (Electro-mechanical controls) Foil faced insulation throughout entire unit Pre-painted exterior panels and primer-coated interior panels tested to 500 hours ASTM B117 (scribed specimen)salt spray protection Internally sloped condensate pan conforms to ASHRAE 62 standards High performance belt drive indoor fan assemblies Internally protected, shaft down totally enclosed condenser motors 2 inch filter standard, field convertible to 4 inch capability 24 volt control system with resettable circuit breakers Induced draft combustion Redundant gas valves with up to two stages of heating Models 48PG 03-28 are E NERGY STAR qualified CENTURION SERIES 48PG units are single piece packaged ultra high efficiency electric cooling with gas heating rooftops. They provide ultra high operating efficiencies, ease of maintenance, ease of installation, and reliability. Units come pre-wired and precharged with PURON (R410A) environmental friendly refrigerant at the factory. Units are factory tested in both heating and cooling modes. Units are rated in accordance with ARI Standard 210 (03-06 sizes) and 360 (07-28 sizes). Tested in accordance with UL Standard 1995 and listed with UL and UL Canada. Approved and certified by: Sizes 03-06 Size 07-28 Certified to ISO 9001:2000 STANDARD WARRANTY: 10-year standard heat exchanger 15-year stainless steel heat exchanger 5-year compressor 1-year parts Many optional upgrades also available MAINTENANCE FEATURES: Single slab, single pass evaporator and condenser coils with dual side access panels facilitate easy cleaning for maintained high efficiencies Hinged access doors with, quick turn latches and door retainers Slide out Indoor fan assembly for added service convenience Dedicated, fully insulated compressor compartment Slide out condensate pan (03-16 models) Permanently lubricated evaporator, condenser and inducer motors INSTALLATION FEATURES: Thru the bottom and side electrical and gas connection capabilities Weather tight thru the bottom access plate Single point electrical and gas connections Return and supply duct fits between 24" on center joist (03-12 models) Field convertible from vertical to horizontal airflow (03-16 models) Single piece outdoor air hoods Full perimeter baserail with built-in rigging adapters and fork truck slots FACTORY INSTALLED OPTIONS INCLUDE: ComfortLINK Direct Digital Controls (DDC) Exclusive Humidi-MiZer adaptive dehumidification system Exclusive EnergyX Energy Recovery module Supply and/or return air smoke detectors Powered or non-powered 115 volt convenience outlet Non-fused disconnect switch or circuit breaker (HACR) Dry bulb or enthalpy economizer with or without return air CO2 sensor Manual outdoor air damper Two position motorized outdoor damper Barometric relief damper Power Exhaust Condenser coil guard MERV-8 Pleated filter upgrade Fan status and filter status switches Side-by-side horizontal ducts (sizes 20-28. Std all other models) High static indoor fan and drive systems Phase loss and compressor reverse rotation protection Corrosion resistant options for evaporator and condenser coils Stainless steel gas heat exchanger Low NOx models that meet California Air Quality Management specs For a complete list of options and accessories refer to the Product Data Catalog for this unit. Packaged Rooftop Builder 1.19k Page 29 of 37

Spec Sheet Spec Sheet for RTU-205 Humidi-MiZer Adaptive Dehumidification System Specification Sheet For Factory Installed Humidi-MiZer systems on 2-25 ton Commercial Rooftop Units APPLICABLE UNITS: 48/50PG, PM 03-28 48/50TC 03-28 48/50HE 003-006 48/50HJ 004-014 GENERAL DATA The Carrier Humidi-MiZer Adaptive Dehumidification system is an all-inclusive factory-installed option, available on Carrier's 2-25 ton unitary rooftop units. It is a cost effective, yet flexible and high performing solution to high humidity and part-load issues for packaged rooftop applications. The system expands the unit's envelope of operation by providing significantly more stages of unit Sensible Heat Ratio (SHR) based on the space temperature and humidity demand. SYSTEM SUMMARY The Humidi-MiZer Adaptive Dehumidification system utilizes a condenser reheat coil, on all refrigerant circuits, located in the airflow path directly downstream from the evaporator. When activated, the refrigerant flows through the condenser, through the Humidi-MiZer coil and then through the evaporator. A condenser bypass line allows hot refrigerant gas to bypass the condenser and vary the refrigerant temperature before it enters the Humidi-MiZer coil. See Figure 1. The location of the coil and the refrigerant flow path allow the refrigerant to be significantly subcooled and the indoor air to be partially reheated for part-load applications or fully reheated for dehumidification only applications. If normal unit operation is required the Humidi-MiZer coil is deactivated. In a two circuit unit, the circuits can be operated independently of each other, allowing a wide range of unit performance and SHR's. SYSTEM FEATURES The Humidi-MiZer Adaptive Dehumidification system features: Reheat coil on all refrigerant circuits in the unit; provides up to 5 additional steps of unit capacity and operation Each circuit in the unit is capable of 3 modes of operation: o Normal - demand for cooling only. Conventional circuit operation and unit leaving air temperatures. o Sub-cooling - demand for space cooling and dehumidification. Unit supply air temperature is approximately 5-7 o F higher than normal supply air temperatures. Allows a conditioned space that is cooled and significantly more dehumidified, but not over-cooled. o ReHeat - demand for space dehumidification only. Unit supply air temperature is neutral (~72-75 but dehumidified. Integrated operation with optional economizer for increased modes of operation and unit flexibility Up to 35% more moisture removal than typical conventional Hot Gas ReHeat systems Unit mode of operation controlled automatically by space temperature and humidity sensors/stats o F) HGSV (Hot Gas Solenoid Valve) Condenser Coil Outdoor Air Humidi-MiZer coil Evaporator Coil Indoor Air LLSV (Liquid Line Solenoid Valve) Fig. 1 - Humidi-MiZer Adaptive Dehumidification System (single circuit unit shown) 1/1 11/1/2008 Packaged Rooftop Builder 1.19k Page 30 of 37

RTU-206 RTU-206 RTU-206 Tag Cover Sheet Unit Report Certified Drawing Performance Report Unit Feature Sheet Spec Sheet Packaged Rooftop Builder 1.19k Page 31 of 37

Unit R eport Unit Report For RTU-206 Unit Parameters Unit Model:...50PG-C03-AJ3 Unit Size:...03 (2 Tons) Volts-Phase-Hertz:... 208-1-60 Heating Type:... None Duct Cfg:Vertical Supply/Vertical Return (Factory Standard) Heating Capacity: Dimensions (ft. in.) & Weight (lb.) *** Unit Length:... 7' 6'' Unit Width:... 4' 6'' Unit Height:... 3' 8'' Base Unit Weight:...704 lb *** Weights and Dimensions are approximate. Weight does not include roof curbs, unit packaging, field installed accessories or factory installed options. Approximate dimensions are provided primarily for shipping purposes. For exact dimensions and weights, refer to appropriate product data catalog. Lines and Filters Condensate Drain Line Size:... 3/4 in. Return Air Filter Type:...Throwaway Return Air Filter Quantity:... 4 Return Air Filter Size:... 16x20x2 Unit Configuration No Electric Heat ComfortLink Controls with Visual Scrolling Marquee Display Low Range Motor/Drive with Vertical SA/RA Al/Cu Cond and Evap and Humidi-MiZer Standard - No EnergyX Warranty Information First Year - Parts Only (Standard) No optional warranties were selected. NOTE: Please see Warranty Catalog 500-089 for explanation of policies and ordering methods. Ordering Information Part Number Description Quantity 50PG-C03-AJ3 Rooftop Unit 1 Base Unit No Electric Heat ComfortLink Controls with Visual Scrolling Marquee Display Low Range Motor/Drive with Vertical SA/RA Al/Cu Cond and Evap and Humidi-MiZer Standard - No EnergyX Packaged Rooftop Builder 1.19k Page 32 of 37

Certified Dr awing Certified Drawing for RTU-206 Packaged Rooftop Builder 1.19k Page 33 of 37

Perfor mance Summar y Performance Summary For RTU-206 Part Number:50PG-C03-AJ3 ARI SEER:...14.10 Base Unit Weight:...704 lb Base Unit Dimensions Unit Length:...90.0 in Unit Width:...53.9 in Unit Height:...44.5 in Unit Voltage-Phase-Hertz:...208-1-60 Air Discharge:... Vertical Fan Drive Type:... Belt Actual Airflow:...800 CFM Site Altitude:...0 ft Cooling Performance Condenser Entering Air DB:...95.0 F Evaporator Entering Air DB:...80.0 F Evaporator Entering Air WB:...67.0 F Entering Air Enthalpy:...31.44 BTU/lb Evaporator Leaving Air DB:...59.3 F Evaporator Leaving Air WB:...57.2 F Evaporator Leaving Air Enthalpy:...24.52 BTU/lb Gross Cooling Capacity:...24.90 MBH Gross Sensible Capacity:...17.90 MBH Compressor Power Input:...1.65 kw Coil Bypass Factor:...0.150 Supply Fan External Static Pressure:...0.40 in wg Options / Accessories Static Pressure Humidi-MiZer (tm) Dehumidification System:...0.02 in wg Total External Static:...0.42 in wg Fan RPM:...577 Fan Power:...0.14 BHP NOTE:... Low Range Fan Option Electrical Data Compressor #1 RLA:...12.8 Compressor #1 LRA:...60 Outdoor Fan Motor Qty:...1 Outdoor Fan FLA (ea):...1 Indoor Fan Motor Type:...Low Indoor Fan Motor FLA:...4.9 Power Supply MCA:...21.9 Power Supply MOCP (Fuse or HACR):...30 Min. Unit Disconnect FLA:...22 Min. Unit Disconnect LRA:...74 Electrical Convenience Outlet:...None Voltage Range:...187-253 Acoustics Sound Rating:...75.0 db Sound Power Levels, db re 10E-12 Watts Discharge Inlet Outdoor 63 Hz 80.9 82.9 82.6 125 Hz 69.0 61.8 79.9 250 Hz 58.0 51.8 75.7 500 Hz 63.6 44.8 73.3 1000 Hz 54.5 43.2 70.0 2000 Hz 52.8 39.8 64.3 4000 Hz 50.7 28.1 58.4 8000 Hz 43.4 31.6 50.5 A-Weighted 63.7 57.6 75.0 Packaged Rooftop Builder 1.19k Page 34 of 37

Performance Summary For RTU-206 2.0 Fan Curve 1200 RPM 100% 1100 RPM 1.5 1000 RPM Static Pressure (in. wg.) 1.0 900 RPM 800 RPM 700 RPM SC 1.00 BHP 0.75 BHP 0.5 600 RPM 500 RPM RP 400 RPM 300 RPM 0.50 BHP 0.0 0.0 0.5 1.0 1.5 2.0 Airflow (CFM - thousands) RPM = 577 BHP = 0.14 Maximum RPM = 2000 Maximum HP = 1.00 SC - System Curve RP - Rated Point Packaged Rooftop Builder 1.19k Page 35 of 37

Unit Featur e Sheet Unit Feature Sheet for RTU-206 PACKAGED ROOFTOP ELECTRIC COOLING UNITS 2, 3, 4, 5, 6, 7.5, 8.5, 10, 12.5, 15, 18, 20, 25 TONS - 50PG STANDARD FEATURES INCLUDE: Puron (R-410A) HFC refrigerant SEER's up to 15.0, EER's up to 12.7, IPLV's up to 13.3 ARI certified outdoor sound levels as low as 72 db Scroll compressors with crankcase heaters, internal line break overload and high-pressure protection Single compressors, single stage cooling on 03-07 models Dual compressors, dual stage cooling on 08-28 models TXV refrigerant metering system on each circuit High Pressure, Low Pressure/Loss of charge, and Freeze protection. Solid core liquid line filter drier on each circuit. Ambient cooling operation from 0 F up to 125 F (DDC controls) and from 40 F up to 125 F (Electro-mechanical controls) Foil faced insulation throughout entire unit Pre-painted exterior panels and primer-coated interior panels tested to 500 hours ASTM B117 (scribed specimen)salt spray protection Internally sloped condensate pan conforms to ASHRAE 62 standards High performance belt drive indoor fan assemblies Internally protected, shaft down totally enclosed condenser motors 2 inch filter standard, field convertible to 4 inch capability 24 volt control system with resettable circuit breakers Models 50PG 03-28 are E NERGY STAR qualified CENTURION SERIES 50PG units are single piece packaged ultra high efficiency electric cooling with optional electric heat rooftops. They provide industry leading operating efficiencies, ease of maintenance, ease of installation, and reliability. Units come pre-wired and pre-charged with PURON (R401A) environmentally friendly refrigerant at the factory. Units are factory tested in both heating and cooling modes. Units are rated in accordance with ARI Standard 210 (03-06 sizes) and 360 (07-28 sizes). Tested in accordance with UL Standard 1995 and listed with UL and UL Canada. Approved and certified by: Sizes 04-06 Sizes 07-28 Certified to ISO 9001:2000 STANDARD WARRANTY: 5-year electric heater 5-year compressor 1-year parts Many optional upgrades also available MAINTENANCE FEATURES: Single slab, single pass evaporator and condenser coils with dual side access panels facilitate easy cleaning for maintained high efficiencies Hinged access doors with, quick turn latches and door retainers Slide out Indoor fan assembly for added service convenience Dedicated, fully insulated compressor compartment Slide out condensate pan (03-16 models) Permanently lubricated evaporator and condenser motors INSTALLATION FEATURES: Thru the bottom and side electrical connection capabilities Weather tight thru the bottom access plate Single point electrical and gas connections Return and supply duct fits between 24" on center joist (03-12 models) Field convertible from vertical to horizontal airflow (03-16 models) Single piece outdoor air hoods Full perimeter baserail with built-in rigging adapters and fork truck slots FACTORY INSTALLED OPTIONS INCLUDE: ComfortLINK Direct Digital Controls (DDC) Exclusive Humidi-MiZer adaptive dehumidification system Exclusive EnergyX Energy Recovery module Supply and/or return air smoke detectors Powered or non-powered 115 volt convenience outlet Non-fused disconnect switch or circuit breaker (HACR) Dry bulb or enthalpy economizer Manual outdoor air damper Two position motorized outdoor damper Barometric relief damper Power Exhaust Condenser coil guard MERV-8 Pleated filter upgrade CO2 sensor Fan status and filter status switches Side-by-side horizontal ducts (sizes 20-28. Std all other models) High static indoor fan and drive systems Phase loss and compressor reverse rotation protection Corrosion resistant options for evaporator and condenser coils Electric heaters For a complete list of options and accessories refer to the Product Data Catalog for this unit. Packaged Rooftop Builder 1.19k Page 36 of 37

Spec Sheet Spec Sheet for RTU-206 Humidi-MiZer Adaptive Dehumidification System Specification Sheet For Factory Installed Humidi-MiZer systems on 2-25 ton Commercial Rooftop Units APPLICABLE UNITS: 48/50PG, PM 03-28 48/50TC 03-28 48/50HE 003-006 48/50HJ 004-014 GENERAL DATA The Carrier Humidi-MiZer Adaptive Dehumidification system is an all-inclusive factory-installed option, available on Carrier's 2-25 ton unitary rooftop units. It is a cost effective, yet flexible and high performing solution to high humidity and part-load issues for packaged rooftop applications. The system expands the unit's envelope of operation by providing significantly more stages of unit Sensible Heat Ratio (SHR) based on the space temperature and humidity demand. SYSTEM SUMMARY The Humidi-MiZer Adaptive Dehumidification system utilizes a condenser reheat coil, on all refrigerant circuits, located in the airflow path directly downstream from the evaporator. When activated, the refrigerant flows through the condenser, through the Humidi-MiZer coil and then through the evaporator. A condenser bypass line allows hot refrigerant gas to bypass the condenser and vary the refrigerant temperature before it enters the Humidi-MiZer coil. See Figure 1. The location of the coil and the refrigerant flow path allow the refrigerant to be significantly subcooled and the indoor air to be partially reheated for part-load applications or fully reheated for dehumidification only applications. If normal unit operation is required the Humidi-MiZer coil is deactivated. In a two circuit unit, the circuits can be operated independently of each other, allowing a wide range of unit performance and SHR's. SYSTEM FEATURES The Humidi-MiZer Adaptive Dehumidification system features: Reheat coil on all refrigerant circuits in the unit; provides up to 5 additional steps of unit capacity and operation Each circuit in the unit is capable of 3 modes of operation: o Normal - demand for cooling only. Conventional circuit operation and unit leaving air temperatures. o Sub-cooling - demand for space cooling and dehumidification. Unit supply air temperature is approximately 5-7 o F higher than normal supply air temperatures. Allows a conditioned space that is cooled and significantly more dehumidified, but not over-cooled. o ReHeat - demand for space dehumidification only. Unit supply air temperature is neutral (~72-75 but dehumidified. Integrated operation with optional economizer for increased modes of operation and unit flexibility Up to 35% more moisture removal than typical conventional Hot Gas ReHeat systems Unit mode of operation controlled automatically by space temperature and humidity sensors/stats o F) HGSV (Hot Gas Solenoid Valve) Condenser Coil Outdoor Air Humidi-MiZer coil Evaporator Coil Indoor Air LLSV (Liquid Line Solenoid Valve) Fig. 1 - Humidi-MiZer Adaptive Dehumidification System (single circuit unit shown) 1/1 11/1/2008 Packaged Rooftop Builder 1.19k Page 37 of 37