BHI770SS 77 cm Flexi Zne Inductin hb with slider cntrl User Manual fr yur Baumatic
BHI770SS 77 cm Flexi-Zne Inductin hb with slider NOTE: This User Instructin Manual cntains imprtant infrmatin, including safety & installatin pints, which will enable yu t get the mst ut f yur appliance. Please keep it in a safe place s that it is easily available fr future reference; fr yu r any persn nt familiar with the peratin f the appliance. JW 20/08/13 2
Cntents Envirnmental nte 4 Imprtant safety infrmatin 5 8 Specificatins 9 11 Prduct and aperture dimensins 9 Prduct specificatins 9 Electrical details 10 Ceramic hb surface layut 10 Cntrl panel layut 11 Using the ceramic hb 11-22 Befre first use 11 Tuch cntrls 12 Switching the hb n 12 Switching n a zne and setting a pwer level 13 Pwer levels 14 Switching ff a zne 14 Switching the hb ff 15 Residual heat indicatr 15 Pan sensr 15 Ckware that is suitable fr an inductin hb 16 The bst functin 16 Using the dual znes (flexi-zne) 17 The hb timer (linked t a cking zne) 18-19 Cancelling a timer functin 19 Lcking the hb tp 20 Safety cut-ff 20 High temperature prtectin 20 Cntrl panel prtectin 21 Detectin f unknwn items 21 The pause/resume functin 21 Hb guidelines 21-22 Cleaning and maintenance 23-24 Cleaning the ceramic hb tp 23 After each use 23 Cleaning table 23 Using a ceramic hb scraper 24 Using a specialist ceramic hb cleaner 24 Installatin 24-31 Psitining 25 Unpacking the appliance 26 Installing the appliance 26-27 Electrical cnnectin 28-29 Cnnecting the mains supply cable 28 Replacing the mains supply cable 29 My appliance isn t wrking crrectly 30-32 Errr cdes 31 Baumatic cnsumables 33 Cntact details 35 3
Envirnmental nte The packaging materials that Baumatic uses are envirnmentally friendly and can be recycled. Please discard envirnment. all packaging material with due regard fr the 4
Imprtant safety infrmatin Yur safety is f the utmst imprtance t Baumatic. Please make sure that yu read this instructin bklet befre attempting t install r use the appliance. If yu are unsure f any f the infrmatin cntained in this bklet, please cntact the Baumatic Advice Line. General Infrmatin This appliance is designed fr dmestic husehld use and fr the cking and frying f dmestic fdstuffs. IMPORTANT: The adjacent furniture and all materials used in the installatin must be able t withstand a minimum temperature f 85 C abve the ambient temperature f the rm it is lcated in, whilst in use. Certain types f vinyl r laminate kitchen furniture are particularly prne t heat damage r discluratin at temperatures belw the guidelines given abve. Any damage caused by the appliance being installed in cntraventin f this temperature limit, will be the liability f the wner. Yur new appliance is guaranteed against electrical r mechanical defects, subject t certain exclusins that are nted in Baumatic s Cnditins Of Guarantee. The freging des nt affect yur statutry rights. The use f this appliance fr any ther purpse r in any ther envirnment withut the express agreement f Baumatic Ltd. will invalidate any warranty r liability claim. Yu shuld nt use this appliance t stre items n r as a wrk surface. N mdificatins t the appliance are permitted by Baumatic Ltd. Yu shuld nt stre r place flammable r highly flammable liquids/materials n tp f r near the appliance. Items made frm aluminium, plastic r plastic film shuld als be kept away frm the appliance, as they may fuse t the surface. Repairs may nly be carried ut by Baumatic service engineers r their authrised service agent. 5
Child Safety Baumatic strngly recmmend that babies and yung children are prevented frm being near t the appliance and nt allwed t tuch the appliance at any time. During and after use, all surfaces will be ht. If it is necessary fr yunger family members t be in the kitchen, please ensure that they are kept under clse supervisin at all times. Older children shuld nly be allwed t utilise the appliance when supervised. General Safety The appliance shuld nly be installed and cnnected by a suitably qualified persn. Care shuld be taken t ensure that the units and wrk surfaces that yu build the appliance int, meet with the relevant standards. If yu ntice any scratches, splits r cracks in the ceramic glass, yu shuld immediately switch ff the appliance and discnnect it frm yur mains supply. Otherwise there is the risk f electric shck ccurring. This appliance is nt intended fr use by persns (including children) with reduced physical, sensry r mental capabilities, r lack f experience and knwledge, unless they have been given supervisin r instructin cncerning use f the appliance by a persn respnsible fr their safety. During use Any film r stickers that are present n the is delivered shuld be remved befre use. hb surface when it Care shuld be taken when utilising there is a risk f burns being caused. the appliance, therwise Yu shuld nt allw the electrical cnnectin cables t cme int cntact with the hb surface when it is ht r any ht ckware. If fat and il verheats, then it can ignite extremely quickly. Fr this reasn, when cking with fat and il the appliance shuld nt be left unattended. 6
Make sure that all f the cking znes are switched ff after use. IMPORTANT: This ceramic inductin hb fully cmplies with current legislatin regarding electr-magnetic interference and is designed nt t interfere with ther electrnic appliances prviding these cmply with the same legislatin. As the hb generates magnetic fields in its immediate vicinity, pacemakers and active heart implants must be designed t cmply with relevant regulatins. If in dubt, yu shuld cnsult the manufacturer f yur device r yur dctr. In this respect, Baumatic can nly guarantee the cnfrmity f ur wn prduct. If an bject made f metal, (e.g. saucepan lid, knife, frk r spn) is placed n a cking zne that is switched n, it can get ht. Cleaning Cleaning f the hb shuld be carried ut n a regular basis. IMPORTANT: Befre attempting t clean the appliance, it shuld be discnnected frm the mains and allwed t cl. Great care shuld be taken whilst using this appliance and when fllwing the cleaning prcedure. Yu shuld nt use a steam jet r any ther high pressure cleaning equipment t clean the appliance. Installatin This appliance must be crrectly installed by a suitably qualified persn, strictly in accrdance with the manufacturer s instructins. Please see the specific sectin f this bklet that refers t installatin. Baumatic Ltd. declines any respnsibility fr injury r damage, t persn r prperty, as a result f imprper use r incrrect installatin f this appliance. 7
Declaratin f cnfrmity This appliance cmplies with the fllwing Eurpean Directives: -2006/95/CE General regulatins / Lw tensin -1935/2004/CE 90/128/EEC This appliance is suitable t cme in cntact with fd -2004/108/CE Electrmagnetic cmpatibility The manufacturer declares that the hb is built using certified materials and requires the appliance t be installed in accrdance with the standards currently in frce. This appliance must be used by a trained persn fr dmestic purpses nly. T avid damaging yur appliance The ceramic glass can be damaged by bjects falling nt it. The ceramic glass edge can be damaged by kncks frm ckware. Cast irn and cast aluminium ckware with damaged bases may scratch the ceramic surface if they are dragged acrss it. Pans shuld be lifted n and ff the hb surface and nt dragged. Cking znes shuld nt be switched n withut ckware placed n it. Als the ckware shuld nt be empty. Fd r liquid that has high sugar cntent may damage the hb tp, if it cmes int cntact with the ceramic hb surface. Any spillages shuld be wiped up immediately, hwever this may nt prevent the hb surface frm becming damaged. 8
Specificatins 55 Prduct dimensins: Aperture dimensins: Depth: 510 mm Depth: 490 mm Width: 770 mm Width: 750 mm Height: 56.6 mm Height: 76.6 mm min (incl. ventilatin) Prduct specificatins: 1 x 1.50 kw inductin znes with bster (2.00 kw) Ø 210 mm 3 x 1.20 kw inductin znes with bster (1.60 kw) Ø 145 mm 1 x 2.40 kw dual (linked) flexi-zne Ø 145 mm x 290 mm Frnt tuch cntrl peratin 4 Individual residual heat indicatrs 2 Independent inductin generatrs Electrnic timer Pan cmpatibility detectin Pause functin Safety lck Stainless steel frame Standard accessries Ceramic hb scraper 9
Electrical details Rated Vltage: Supply Cnnectin: Max Rated Inputs: Mains Supply Lead: 220-240 V~ / 380-415 2N~ Vac 50-60 Hz 32A (duble ple switched fused utlet with 3mm cntact gap) 6.80 kw 3 cre x 6 mm² (nt supplied) Fr future reference please recrd the fllwing infrmatin which can be fund n the rating plate and the date f purchase which can be fund n yur sales invice. The rating plate f yur hb is lcated n the underneath f the appliance. Therefre it is a gd idea t recrd this infrmatin befre yu install yur appliance. Mdel Number Serial Number.. Date f Purchase. Ceramic hb surface layut 1) 1 x 1.20 kw inductin znes with bster (1.60 kw) Ø 145 mm 2) 1 x 1.50 kw inductin znes with bster (2.00 kw) Ø 210 mm 3) 1 x 1.20 kw inductin znes with bster (1.60 kw) Ø 145 mm 4) 1 x 1.20 kw inductin znes with bster (1.60 kw) Ø 145 mm 3) + 4) 2.40 kw dual (linked) inductin flexi-zne Ø 145 X 290 mm 5) Cntrl panel 10
Cntrl panel layut 1) ON/OFF buttn 2) Safety lck buttn 3) Pause / Resume buttn 4) Cking zne selectin buttns (x 4) 5) LED displays (x5) 6) Slider cntrl (Pwer cntrl) 7) Timer cntrl (Minus buttn) 8) Timer cntrl (Plus buttn) Using the ceramic hb Befre first use IMPORTANT: Yu shuld clean the ceramic hb surface (see Cleaning and maintenance sectin). Yu shuld switch n ne cking zne at a time fr 5 minutes at the maximum setting. This will help t eliminate any new smell that exists and evaprate any humidity that has frmed n the heating elements during transit. D nt burn ff mre than ne zne at nce. Yu must place a saucepan filled half full with cld water n each zne as yu burn it ff. Otherwise the inductin zne will nt perate. 11
Tuch cntrls All peratins are perfrmed by means f the tuch cntrls that can be fund n the cntrl panel. The cntrls respnd t tuch s yu d nt need t add any pressure. Yu shuld use the ball f yur finger nt the tip when using the cntrls. Calibratin f tuch cntrls When the hb is pwered n fr the first time (r after a pwer cut), it generates a reset in the user interface and the cntrl panel will need t be recalibrated. The first time yu tuch the Safety Lck buttn (2), the hb will calibrate the tuch cntrl sensitivity. In rder that the hb can calibrate the cntrl panel crrectly, yu must use a clean finger and DO NOT use glves when tuching the cntrls. The calibratin prcess als requires lw ambient light levels in the area f the tuch cntrls. Please TURN OFF any cker hd lighting when calibrating the cntrls. The ambient lighting will be detected within apprximately 3 secnds f initial pwer n. IMPORTANT: If during this calibratin prcess excessive ambient lighting is detected (fr example, cker hd lighting is n) the cntrl panel displays errr cde FL. The LED displays will flash FF and LL alternately. If r when there are n ambient light errr cdes, press the Safety lck buttn t calibrate the hb cntrls. Wait fr apprximately 3 secnds and then yur appliance will be ready fr use. Switching the hb n When the hb is cnnected t a pwer supply, an audible signal will sund and all f the cking zne indicatrs will light. The hb will enter stand-by mde after 10 secnds f inactivity. Press the safety lck buttn t unlck the cntrl panel (if it is lcked). Press the ON/OFF buttn (1) t turn n the hb, all displays shw 0. 12
Switching n a zne and setting a pwer level IMPORTANT: A zne must be selected within 1 minute f turning the hb n. Make sure that the bttm f the pan and the surface f the hb are clean and dry befre placing a suitable pan n the cking zne that yu wish t use. Press the cking zne selectin buttn ( 4 ) f the cking zne that yu want t use. Select the pwer level fr the cking zne that yu have selected using the slider cntrl. If yu d nt chse a heat setting within 1 minute f turning the hb n, the hb will switch ff autmatically. Sliding the slider cntrl t the right will increase the pwer level while sliding the slider cntrl t the left will decrease the pwer level. The pwer level will shw in the relevant display (0 9). Yu can alter the pwer level at any time during cking using the slider cntrl. If the display flashes with the symbl shwn ppsite, alternatively with the heat setting, this means that: Yu have nt placed a pan n the crrect cking zne r, The pan yu are using is nt suitable fr inductin cking r, The pan is t small r nt prperly centred n the cking zne. N heating will take place unless there is a suitable pan n the cking zne. The display will autmatically turn ff after 1 minute if n suitable pan is placed n it. 13
Pwer levels Fr a general guide t cking varius fds at the different pwer levels please refer t the table belw. Please nte that this table shuld be viewed as a guide nly and that ther factrs such as ckware, weight and amunt f fd and persnal preference will all influence the pwer level required. Pwer Recmmended Use Level 1-2 Delicate warming f small amunts f fd. Melting chclate, butter and fds that burn quickly. Gentle simmering. Slw warming. 3-4 Reheating. Rapid simmering. Cking rice. 5-6 Cking pancakes. 7-8 Sautéing. Cking pasta. 9 - Bst Stir-frying. Searing. Bringing sup t the bil. Biling water. Switching ff a zne Press the cking zne selectin buttn f the cking zne that yu want t switch ff. Turn the cking zne ff by tuching smallest dt n the pwer level cntrl. Ensure display shws pwer level 0. After a few secnds the cking zne will turn ff. A H symbl will shw in the cking zne indicatr until the surface has cled dwn t a safe temperature (see the sectin n the residual heat indicatr fr further infrmatin). 14
Switching the hb ff Once yu have switched ff all f the cking znes, yu shuld switch the hb ff. Press the ON/OFF buttn. It is pssible t turn the hb ff at any time by pressing the ON/OFF buttn. Residual heat indicatr After a zne is switched ff, the crrespnding cking zne indicatr will shw a letter H. This means that the temperature f the zne is ver 60 C and is therefre still high enugh t cause injury. IMPORTANT: The residual heat indicatr will disappear if yur mains supply is cut. Care shuld be taken in case the surface temperature is still high. Pan sensr Each zne has a sensr n it, s it can detect the presence f a pan. The sensr is fine-tuned t detect a pan being placed n it. The pan shuld be ne size smaller than the nminal diameter f the zne. If after placing a pan n a cking zne and selecting that cking zne, a U shaped symbl appears n the cking zne indicatr, this means that the pan is either the incrrect size r shape. Or it culd be made frm a material that is inapprpriate fr use n an inductin zne hb. If a cking zne is selected but n pan is detected, the pan sensr system will check fr the presence f a pan apprximately every few secnds. If n pan is detected after 1 minute the hb will autmatically switch ff Yu shuld check that yur pans are suitable fr use n an inductin zne hb (see the pan manufacturer s trademark r instructins). 15
Ckware that is suitable fr an inductin hb The table belw shws ckware that is nrmally suitable fr use n an inductin zne hb:- Ckware Steel, enamelled steel Cast irn Stainless steel Aluminium, cpper, brass Glass, ceramic, prcelain Suitable Yes Yes Yes (if stated by the pan manufacturer) N N The bttm f the pans shuld be as flat and thick as pssible. Certain types f ckware may result in a nise being made when being used n an inductin zne hb. This des nt mean that there is an appliance fault. IMPORTANT: Yu shuld make sure that all pans are placed in the centre f the inductin zne that yu are using. The (pwer) bst functin T btain a faster and mre pwerful heating speed, the bster functin can be used fr any cking zne. Press the cking zne selectin buttn f the zne yu wish t use. When yu select a temperature using the slider cntrl, yu shuld select the highest temperature (the dt furthest t the right) which is labelled as Bster. The relevant cking zne indicatr will shw P t indicate that the functin has been activated. The bst functin will perate the chsen cking zne at maximum pwer fr 10 minutes. After this time, the cking zne will return t level 9 pwer setting. The bster functin can be used n every cking zne except the dual/flexi-zne. The bster functin can be de-activated by selecting the relevant zne and then selecting a new temperature frm 1 9, r by selecting 0 n the cntrl panel (lwest setting) t turn ff. 16
Switching n a dual circuit flexible cking zne The dual circuit cking znes enable yu t use the tw left (vertical) cking znes simultaneusly, creating ne large zne. This functin is particularly useful when using larger / val / rectangular r elngated pts and pans, but can als be used t ck with several smaller pts. Press ne f the dual zne selectin keys, and immediately after press the ther dual zne selectin key. The LED display f bth znes will begin t flash. Adjust the pwer in the usual way by using the pwer slider cntrl, and this will cntrl the pwer f bth znes simultaneusly. NOTE: If fr example yur pan is mved frm the frnt area f the dual zne t the rear f the dual zne, the flexible area autmatically detects the new psitin f the pan and will adjust the heating accrdingly whilst keeping the same pwer. When using the dual znes ckware shuld be placed as central as pssible and shuld ideally cver bth crsses. Switching ff a dual circuit zne Yu can turn ff the dual zne by the nrmal way f selecting (either zne) and reducing the pwer t 0 (r t anther temperature level). Yu can yu als separate the znes by first pressing the individual cking znes selectin buttn. When the LED displays begins t flash (fr bth znes), press either f the dual cking zne selectin buttns again, and this will select nly the cking zne yu have just pressed. 17
The hb timer (linked t a cking zne) Yu are able t link a cuntdwn time t a cking zne s that when the cuntdwn time has elapsed the cking zne will switch ff autmatically. Press the ON/OFF buttn t turn the hb n. Press the cking zne selectin buttn f the zne yu wish t use. Tuch either timer cntrl [7/8] (plus r minus buttns), and the digits will shw 00 in the timer display. Set the time by tuching the plus and minus buttns [7/8]. The display will shw the time yu have set. When yu are happy with the chsen time release all buttns. After 5 secnds f inactivity the time will be set and the cuntdwn will begin. NOTE: The red dt next t pwer level indicatr will illuminate indicating that the zne is selected. When cking timer expires, the crrespnding cking zne will be switch ff autmatically. IMPORTANT: All ther cking znes which are in use will cntinue t perate. 18
A red dt will appear next t the pwer level indicatr f the relevant zne. When yu set a cuntdwn time fr several znes simultaneusly, a red dt will appear in all the relevant zne indicatrs. The timer display will shw the lwest cuntdwn time and the crrespnding red dt will flash. (set t 15 minutes) (set t 45 minutes) When the set cuntdwn time has elapsed, the relevant cking zne will switch ff autmatically. If cuntdwn timers fr ther cking znes are set, the timer display will then shw the next lwest cuntdwn time and the crrespnding red dt will flash. WARNING: If any ther cking znes are in use, withut a cuntdwn timer set, they will cntinue heating. Yu will need t switch them ff manually when cking is cmplete. NOTE: Yu can silence the alarm by pressing any buttn. NOTE: yu can press and hld the timer buttns [7/8] which will mean that the time will scrll (change) mre rapidly. NOTE: the timer will display the last minute f the cuntdwn in secnds Changing the cuntdwn time T change the cuntdwn time, first select the desired zne, and then press the timer buttns [7/8]. The cuntdwn time will pause and yu can adjust the time as previusly described. After 5 secnds f inactivity the new cuntdwn time will begin. Cancelling a hb timer T cancel a hb timer, first select the zne that yu want t turn ff the timer, and then press the minus key t reduce the timer t 00. Alternatively, yu can press the plus ( + ) and minus ( - ) buttns simultaneusly fr a few secnds. 19
Lcking the hb tp It is pssible t lck the cntrls t prevent unauthrised usage f the cntrls by ther persns such as children. The whle hb tp can be lcked by pressing the safety lck buttn whilst the appliance is switched n. The LED light next t the lck symbl n the cntrl panel will light t indicate that the safety lck feature has been switched n. When the safety lck feature is activated, it will disable all buttns n the cntrl panel apart frm the ON/OFF buttn and the lck buttn. T disable the safety lck feature, yu shuld press and hld the safety lck buttn fr a few secnds. The lck symbl LED will g ut and yu are then able t use the hb in nrmal peratin. If the hb is switched ff using the ON/OFF buttn while the safety lck is activated, the safety lck will still be active when the hb is turned back n. Safety cut-ff If ne r mre f the cking znes are accidentally left n, a safety cut ff will activate after a certain perid f time. The length f time depends n the pwer level that a zne r znes have been set n. Pwer level 1 2 3 4 5 6 7 8 9 Bst Default wrking timer (hur) 10 5 5 4 3 3 2 2 1 10 Mins If mre than ne zne is perating when ne f the znes reaches its safety cut-ff pint, nly the zne which has reached its safety cut ff pint will switch ff. High temperature prtectin The hb is equipped with a temperature sensr which mnitrs the temperature inside f the appliance. If an unusually high temperature is detected the inductin hb will stp perating autmatically. 20
Cntrl panel prtectin If any key(s) is pressed cntinuusly fr mre than 10 secnds the hb tp switches ff autmatically. A warning beep sunds every 10 secnds while the key(s) is activated. Detectin f unknwn items When an unsuitably sized r nn-magnetic pan (e.g. aluminium), r sme ther small item (e.g. knife, frk, key) has been left n the hb, the hb will autmatically g n t standby mde after 1 minute. The fan may keep cling the inductin hb after it has been turned ff, depending n the temperature f the hb. The pause/resume buttn This feature allws the user t pause all cking peratins, and is particularly useful fr situatins such as answering the dr r telephne, r fr cleaning the cntrl panel withut changing the settings. Using this buttn will stp all znes frm heating and will als pause any active timers. All znes will display a circular LED (a running line ). The cntrl panel will autmatically be lcked and nly the pwer buttn and the pause/resume buttn will perate. Press the pause/resume buttn again t resume all previusly in use znes. The znes will resume heating at the pwer level which they were riginally set at and will display the riginal pwer settings. The pause functin will n l y perate fr 10 minutes. After this time the hb will turn ff. Hb guidelines The first few times the hb tp is used, it may give ff an acrid, burning smell. This smell will disappear cmpletely with repeated use. Single zne ckware shuld be placed n the + and centred. When using the dual znes ckware shuld be placed as central as pssible and shuld cver bth crsses where pssible. 21
O The saucepans must be psitined exactly n these znes fr efficient heating t ccur. Pans shuld have the same diametre as the cking zne that they are being used n. Yu shuld nt use saucepans with rugh bttms, as this can scratch the ceramic surface. Befre use, make sure that the bttms f the saucepans are clean and dry. When cld, the bttm f the pans shuld be slightly cncave, as they expand when ht and lie flat n the surface f the hb. This will allw the heat t transfer mre easily. The best thickness fr the bttm f the pans is 2 3 mm f enamelled steel and 4 6 mm fr stainless steel with sandwich type bttms. If these rules are nt fllwed, then there will be a great lss f heat and energy. Heat nt absrbed by the saucepan, will spread t the hb, frame and surrunding cabinets. Preferably cver pans with a lid t permit cking at a lwer heat. Always ck vegetables and ptates, etc. in as little water as pssible t reduce cking times. Fd r liquid that has high sugar cntent may damage the hb tp if it cmes int cntact with the ceramic hb surface. Any spillages shuld be wiped up immediately, hwever this may nt prevent the hb surface frm becming damaged. IMPORTANT: The ceramic hb surface is tugh; hwever it is nt unbreakable and can be damaged. Especially if pinted r hard bjects are allwed t fall n it with sme frce. DO NOT USE THE HOB IF THE SURFACE BECOMES BROKEN OR CRACKED. YOU SHOULD CONTACT THE BAUMATIC CUSTOMER CARE DEPARTMENT IMMEDIATELY. 22
Cleaning and maintenance Cleaning peratins must nly be carried ut when the hb is cl. The appliance shuld be discnnected frm yur mains supply befre cmmencing any cleaning prcess. Cleaning the ceramic hb tp Any residues that are left n the hb tp surface frm cleaning agents will damage it. Yu shuld remve any residues with warm water and a little washing up liquid. Abrasive cleaners r sharp bjects will damage the hb surface; yu shuld clean it using warm water and a little washing up liquid. Althugh it is easier t clean sme depsits whilst the hb surface is still warm, yu shuld take care nt t burn yurself. After each use Wipe the appliance ver with a damp clth and a little washing up liquid. Dry the appliance by rubbing the surface with a clean clth. Cleaning table Type f depsit Sugar r fd/liquid cntaining sugar Remve immediately? Remve when the appliance has cled dwn? What shuld I use t remve the depsit? Yes N Ceramic hb scraper Tin fil r plastic Yes N Ceramic hb scraper Fat splashes N Yes Ceramic hb cleaner Metallic discluratins N Yes Ceramic hb cleaner Water splashes r water rings N Yes Ceramic hb cleaner 23
Using a ceramic hb scraper A ceramic hb scraper will be prvided with yur appliance. The fllwing guidelines shuld be fllwed when using the ceramic hb scraper:- The scraper shuld be placed n the ceramic surface at an angle. Residues shuld be remved by sliding the blade carefully ver the ceramic surface. The ceramic surface shuld be wiped with a damp clth and a small amunt f washing up liquid. Dry the appliance by rubbing the surface with a clean clth. Using a specialist ceramic hb cleaner It is pssible t purchase specialist ceramic hb cleaner/cnditiner. Yu shuld fllw the instructins given by the manufacturer f the specialist ceramic hb cleaner. Yu shuld ensure that it is suitable fr use n yur appliance. Installatin The installatin must be carried ut by a suitably qualified persn, in accrdance with the current versin f the fllwing. UK Regulatins and Safety Standards r their Eurpean Nrm Replacements. Building Regulatins (issued by the Department f the Envirnment). Building Standards (issued by the Scttish Develpment Department). IEE Wiring Regulatins. Electricity At Wrk Regulatins. 24
Psitining The adjacent furniture must be able t withstand a minimum temperature rise f 85 C abve the ambient temperature f the rm it is lcated in, during perids f use. This appliance is classified as Class 3 and therefre is t be built int a kitchen unit (depending n size) r 600 mm wrktp that is at least 30 mm thick. The fllwing minimum clearance distances must be bserved:- 700 mm between the hb surface and the underside f any hrizntal surface abve it. 50 mm clearance arund the sides and frnt f the appliance, measured frm the cut ut. 55 mm clearance between the back f the hb surface and the wall behind it, measured frm the cut ut. If the hb is psitined s that the right r left hand side f the appliance will be near t the edge f a kitchen unit. There must be a gap f at least 150 mm between the side f the hb and the vertical surface f the kitchen unit. IMPORTANT: Underneath the appliance there must be a partitin made f insulating material (e.g. wd). There must be a gap f at least 20 mm between the underneath f the appliance and this partitin. Yu must make sure that there is a 5mm gap belw the underneath f the wrktp at the frnt edge f the hb. Installing abve a built under ven IMPORTANT: If yu are building this hb abve an ven, the ven MUST have a cling fan. 25 There must be a gap f at least 20mm between the underneath f the appliance and the tp f the ven/surface belw, a 5mm gap belw the underneath f the wrktp at the frnt edge f the hb, and 30mm gap at the rear f the appliance, fr ventilatin.
Unpacking the appliance When unpacking the appliance please check that the fllwing items are cntained within the packaging:- 1 Baumatic hb 1 Ceramic hb scraper 1 Installatin and instructin manual 1 Baumatic guarantee card Fixing brackets Fixing screws Installing the appliance Cut a hle in shwn abve. the wrktp that crrespnds with the drawing IMPORTANT: There are ventilatin hles arund the utside f the hb. YOU MUST ensure that these hles are nt blcked by the wrk tp, when yu put the hb int psitin (see drawing ppsite). 26
Carefully turn the hb upside dwn and place it n a cushined mat. IMPORTANT: D nt use a silicn sealant t seal the appliance against the aperture. This will make it difficult t remve the hb frm the aperture in future, particularly if it needs t be serviced. Carefully turn the hb back ver and then gently lwer it int the aperture hle that yu have cut ut. There are hles n the base f the hb that yu can fix the tw brackets t. Yu shuld place the bracket n the underneath f the hb, in a psitin that is apprpriate fr the aperture that yu have cut ut. Using the screws prvided, fix the bracket t the hb. These screws MUST be securely tightened. 27
Electrical cnnectin This appliance must be installed by a qualified persn in accrdance with the latest editin f the I.E.E. Regulatins and in cmpliance with Baumatic s instructins. Befre cnnecting the appliance, make sure that the supply vltage marked n the rating plate crrespnds with yur mains supply vltage. WARNING: THIS APPLIANCE MUST BE EARTHED. This appliance must be wired int a 32A duble ple switched fused spur utlet, having 3 mm cntact separatin and placed in an easily accessible psitin adjacent t the appliance. It shuld nt be lcated abve the appliance and n mre than 1.25m away frm it. The spur utlet must still be accessible even when yur hb is lcated in its perating psitin. Cable type: H05 RRF 3 cre x 6 mm² Cnnecting the mains supply cable Single phase: The mains terminal blck is lcated n the underside f the hb and the terminals are accessible by remving the terminal blck cver by remving the cver screw. IMPORTANT: The pwer cable is nt supplied with the appliance. The brass links must be psitined as shwn in the images abve and nce established ALL terminal screws must be tightened dwn firmly. Yu shuld use a gd quality screwdriver t carefully, fully tighten ALL f the terminal screws. If when the hb is first switched n, nly tw f the znes wrk, yu shuld recheck that the terminal screws are all fully tightened. This shuld be dne befre cntacting the Custmer Care Department. 28
IMPORTANT: The appliance must NOT be cnnected t the mains supply by means f a 13A plug and scket. The cable can be lped if necessary, but make sure that is nt kinked r trapped when the hb is in psitin. Care must be taken t avid the cable being in cntact with ht parts f the appliance. Replacing the mains supply cable If the mains supply cable is damaged, then it must be replaced by an apprpriate replacement which can be btained via the manufacturer / spares department. The mains supply cable shuld be replaced in accrdance with the fllwing instructins: Switch the appliance ff at the mains supply. Open the terminal blck n the underside f the hb. Unscrew the terminal screws fixing the cable. Replace the cable with ne f the same length and in accrdance with the specificatin given n the previus page. The green-yellw earth wire must be cnnected t the terminal marked. It must be abut 10 mm lnger than the live and neutral wires. The blue neutral wire must be cnnected t the terminal marked with letter (N) - the live wire must be cnnected t the terminal marked with letter (L). 29
My appliance isn t wrking crrectly The cking znes are nt functining r will nt switch n. * The safety lck has been switched n (see the Lcking the hb tp sectin fr infrmatin n hw t turn ff the safety lck). * Several cking zne selectin buttns have been pressed at nce. Yu shuld nly tuch ne cking zne selectin buttn at nce. * The safety cut ut has been triggered. Press a cking zne selectin buttn t reset the hb. * Check that the mains electrical supply t the appliance is crrect and wrking. Check the mains fuse. * The pans that yu are using are nt suitable fr use n an inductin hb. The residual heat indicatr has nt cme n after I have switched a cking zne ff. * The cking zne has nly been turned n fr a shrt perid f time; therefre it did nt g abve 60 C. * IMPORTANT: If the cking zne des appear t be htter than 60 C and the residual heat indicatr has nt cme n, yu shuld call the Baumatic Custmer Care Department. A humming sund is heard when a cking zne is selected. * This is nrmal; the sund will disappear when the zne heats up. * The cking znes have becme disclured. This maybe caused by burnt n remnants f fd. This will nt affect the wrking f the appliance. Hwever yu shuld make sure that the cleaning instructins are being fllwed regularly. Only tw f the znes n my hb are wrking * Yu shuld recheck that the terminal screws are all fully tightened between the links. There is a lt f cndensatin abve/arund the hb (e.g. cker hd) This is a natural phenmenn caused by the lack f (wasted) heat nrmally prduced by cnventinal hbs. The surrunding area is therefre cler which increases the likelihd f cndensatin due t the increased humidity. 30
Errr cdes The fllwing errr cdes may appear in the timer display if there is a prblem with the peratin f the hb. Fault Pssible cause Slutins F0, F6, FA, FC, Electrnic fault. Cntact the Custmer Care Department FU, F5, FH, FJ, Micr-emitter r micr-receiver fault. FE, Ft, Fc, F1, F2, F7, F8, F3, F4 F9 Temperature and/r sensr failure Abnrmal vltage frm the mains supply Check that the pan is f the crrect size t be used n a particular zne. If the pan is crrectly sized and the errr cde reappears then Cntact the Custmer Care Department, quting the errr cde. Check whether the pwer supply is perating nrmally. r Restricted pwer Check whether the pwer supply is perating nrmally. If n fault fund cntact Custmer Care. u Pan sensr errr Check that yu are using suitable utensils. H Residual heat sensr This light shuld g ut when the hb zne has cled. FL, FF, LL Ambient light fault Ensure ambient lighting is nt t high r t lw. Please see page 12 and read the guidance n the calibratin f the tuch cntrls. IMPORTANT: If any ther errr cdes appear n the cking zne display, yu shuld turn the appliance ff at the mains and cntact the Custmer Care Helpline. DO NOT cntinue t use the appliance. 31
IMPORTANT: If yur appliance appears nt t be perating crrectly, then yu shuld discnnect it frm yur mains supply and then cntact Baumatic Custmer Care n telephne number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please nte that if an engineer is asked t attend whilst the prduct is under guarantee and finds that the prblem is nt the result f an appliance fault, then yu may be liable fr the cst f the call ut charge. The appliance must be accessible fr the engineer t perfrm any necessary repair. If yur appliance is installed in such a way that an engineer is cncerned that damage will be caused t the appliance r yur kitchen, then they will nt cmplete a repair. This includes situatins where appliances have been tiled in, sealed in with sealant, have wden bstructins placed in frnt f the appliance - like plinths, r any installatin ther than the ne specified by Baumatic Ltd. has been cmpleted. Please refer t the cnditins f guarantee that appear n the warranty card that yu receive with the appliance. IMPORTANT: Baumatic Ltd. perates a plicy f cntinuus imprvement and reserves the right t adjust and mdify its prducts withut prir ntificatin.
Baumatic Cnsumables BC001 Degreaser fr Dishwashers (200 g) BC002 Descaler fr Washing Machines and Dishwashers (200 g) BC003 Ceramic Hb Cleaner (250 ml) BC004 Oven Cleaner (250 ml) BC005 Stainless Steel Cleaner and Prtectr (250 ml) BC007 E-Clth General Purpse Clth BC008 Micrwave Cver T rder a Baumatic cnsumable prduct please call 0123 5437 244 and qute the prduct cde. Yu can als rder nline frm eshp.baumatic.c.uk
33 33
United Kingdm Baumatic Ltd., Baumatic Buildings, 6 Bennet Rad, Reading, Berkshire RG2 0QX United Kingdm Sales Telephne (0118) 933 6900 Sales Fax (0118) 931 0035 Custmer Care Telephne (0118) 933 6911 Custmer Care Fax (0118) 986 9124 Spares Telephne (01235) 437244 Advice Line Telephne (0118) 933 6933 E-mail: sales@baumatic.c.uk custmercare@baumatic.c.uk spares@baumatic.c.uk technical@baumatic.c.uk Website: www.baumatic.c.uk Facebk: www.facebk.cm/baumatic.uk Republic f Ireland Service Telephne 1-890 812 724 Spares Telephne 091 756 771 Czech Republic/Slvakia Baumatic s.r.. Lípvá 665/1 460 01 Liberec 4 Czech Republic Panenská 34 811 03 Bratislava - Staré Mest Slvakia +420 483 577 200 (CZ) +421 255 640 618 (SK) www.baumatic.cz www.baumatic.sk Germany Kundendienst & Ersatzteile Deutschland 0049(0)180-5888975 Oesterreich +43 (0) 820 / 420423 www.baumatic.de Italy Baumatic Italia S.R.L. Via Galvani N.3 35011 Campdarseg (PD) +3904 9920 2297 www.baumatic.it Hlland Baumatic Benelux B.V. Dukdalfweg 15d 1332 BH ALMERE Nederland +31(0)36 549 1553 / 1555 www.baumatic.nl 34 34
www.baumatic.cm 35 35