FOOD WARMING/MERCHANDISING CABINET MODEL 680-1 (Single Door) MODEL 680-2 (2 Door pass through) This warmer provides bottom heat to keep crusts crisp. The illuminated shelves are thermostatically controlled to provide temperature flexibility. Also ideal for holding cookies, biscuits, muffins and other foods at proper serving temperatures. FEATURES: - Red hood with pizza pictured Ready To Go graphic panels (#I013757) - Adjustable thermostat - Temperatures from 80 F to above 150 F - 2 heated, illuminated shelves - Each shelf accommodates up to a 16 pizza - Optional racks available (1 per shelf) FLAT (#0016777) or 3/4 RAISED (#0016289) - Great for placing on top of the Wisco Model 560 pizza oven for a space saving feature ELECTRICAL DATA: VOLTS: 120 AMPS: 2.1 WATTS: 260 - Best when operated on an individual branch circuit - 5 power cord length DIMENSIONS: Outside: 24 H x 18 W x 18 D Inside: 13-1/2 H x 17 W x 17 D SHIPPING INFORMATION: SHIPPING DIMENSIONS: 24 L x 24 W x 32 H SHIPPING WEIGHT: 37 lbs. FP140026 08/08/14
IMPORTANT: Read the following safety and operation instructions to avoid injury and to avoid damage to equipment or property. Plug unit into a properly grounded electrical outlet of the correct voltage, size and plug configuration for this unit. We recommend usage on an individual branch circuit of at least 15 amps for best results. Failure to do so may result in decreased performance of the warmer. Only shatter resistant light bulbs which meet or exceed NSF Standards specifically designed for food holding units must be used. Breakage of bulbs not specially coated could result in personal injury and/or food contamination. Exterior surfaces on unit may get hot. Use caution when touching these areas to avoid injury. Unplug oven when not in use EQUIPMENT SET UP Once the unit has been taken out of the shipping carton and has been unpackaged, check to make sure that all light bulbs are securely in their sockets. CLEANING INSTRUCTIONS Unit is not waterproof. Do Not submerge in water. Do not operate if unit has been submerged in water. Unplug unit from power source and allow to cool completely before performing any maintenance or cleaning. The use of any type of ammonia, alcohol or chlorine based household cleaners will cause cracking of the door/enclosure and is not covered under any warranty. Use warm soapy water and a soft cloth only. It is recommended that the interior and exterior surfaces be cleaned daily with a mild soap and damp cloth. Stubborn stains on base of unit and/or shelves may be removed with a non-abrasive cleaner and a damp cloth. Usage of an abrasive cleanser could scratch or damage the finish of your unit. STEP 1: Unplug unit from electrical supply STEP 2: Let unit cool before cleaning STEP 3: Clean with warm soapy water and a soft cloth only TO REPLACE DISPLAY LIGHT & SHELF BULBS Only shatter resistant light bulbs which meet or exceed NSF Standards specifically designed for food holding units must be used. Breakage of bulbs not specially coated could result in personal injury and/or food contamination. Disconnect the power supply and wait until unit has cooled completely before replacing any lights or bulbs.
WIRING EXPLODED PARTS OPERATION: LIST: DIAGRAM: VIEW: This warmer is designed to maintain food product at or above the optimum temperature. It is not designed or intended to heat up or cook food to the serving temperature. Product is to be prepared to a temperature of above 160 F before placing in the warmer. Do not place product on its side as this will affect the internal holding temperatures of the product. TEMPERATURE The amount of product placed in the warmer will affect the performance of the warmer. We suggest periodically checking the internal temperature of the product and adjusting the temmperature settings if necessary. Keep door(s) closed when not serving. The following temperatures are APPROXIMATE and can vary due to unit location, electrical supply, product used, etc. *Intended as a guideline only. SETTING THERMOMETER READING 1 85 F 2 105 F 3 140 F 4 165 F 5 Above 190 F OPERATING INSTRUCTIONS 1. Plug unit in. 2. Before loading prepared food product into warmer, you must preheat the unit for 30 minutes at a setting of 4 or 5 on the thermostat dial. After the preheat time has elapsed you can then go ahead and place the previously prepared food product inside. 3. Set thermostat to desired level. * Pizza should be placed on a standard aluminum pizza pan and not directly on the warmer shelf. This will keep product from drying out for a longer period of time and will also help keep the cabinet cleaner. * When placing your product on pizza pans we recommend a setting of 4 or 5. Settings vary depending on product weight, consistency and personal preference. CAUTION: Pans get hot. Use hot pads/oven mitts when removing pans from the food warmer. NOTES:
WIRING EXPLODED PARTS TROUBLESHOOTING: LIST: DIAGRAM: VIEW: Unplug unit from power source and allow to cool completely before performing any maintenance or cleaning. Unit not working: - Check power switch position, power cord and/or electrical circuit Display light not working: - Tighten or replace bulb Shelf light not working: - Replace bulb Unit not heating properly: - Has food been prepared in advance and placed in warmer at proper serving temperature? - Check heat settings. Is it at correct setting for your food product? Food product drying out: - Are you placing food product directly on shelf or on an aluminum pan as recommended? - Is your food product being left in the warmer past its shelf life? * Shelf life is determined by personal preference and can vary greatly dependant upon the product, how it is packaged, etc. NOTES:
WIRING EXPLODED PARTS LIST: DIAGRAM: VIEW:
Model 680-1 Exploded View 1 2 3 4 23 5 6 16 19 22 7 8 20 16 9 16 19 Controls Detailed View 21 18 17 15 14 13 12 11 10 Rev. Date: 05/24/2012
Model 680-1 Wiring Diagram Current Model (Single Switch) 24 25 12 11 9 10 Obsolete Model (Dual Switch) 24 25 12 11 9 10 Rev. Date: 05/24/2012
WIRING EXPLODED PARTS LIST: DIAGRAM: VIEW:
LIMITED WARRANTY/ RETURN POLICY 1 YEAR REPLACEMENT/EXCHANGE Wisco Industries, Inc. warrants its equipment against defects in materials and workmanship subject to the following conditions: Should any product fail to function in its intended manner under normal use within the limits defined in this warranty, Wisco Industries will determine if the item is to be repaired or replaced by Wisco Industries. Failure to follow authorizing instructions may void any claim and/or warranty. * Contact Wisco Industries for repair/replacement by calling (608) 835-3106 or toll free (800) 999-4726. You can also email us at: contact@wiscoind.com * An authorizing RMA# must be obtained through Wisco Industries BEFORE any warranty issues can be resolved. Failure to do so in advance may void the warranty/claim resulting in Wisco Industries not being responsible for any incurred expenses and/or charges. * At time of call Wisco Industries will assist you in: - getting your unit replaced/exchanged - and/or obtaining repair parts - and/or authorizing a service agent This warranty covers products shipped into the 48 contiguous Unites States, Hawaii, metropolitan areas of Alaska. Warranty for international or areas not listed above will consist of replacement of parts only. There will be no labor coverage and parts must be shipped to an address within the 48 contiguous United States, Hawaii, metropolitan areas of Alaska and Canada only. Time Period One year from date of shipment from our manufacturing facility. Parts replaced under this warranty are warranted for the un-expired portion of the original product warranty only. Exclusions The following conditions are not covered by warranty: - Equipment failure relating to improper installation and improper utility connection or supply. - Equipment that has not been properly maintained or damage from improper cleaning and/or water damage to controls. - Equipment that has not been used for its intended purpose or has been subject to misuse or misapplication, neglect, abuse, accident, alteration, negligence, damage during subsequent transit, delivery or installation, fire, flood, riot or act of god. - Equipment that has the model number or serial number removed or altered. WISCO INDUSTRIES, INC. DISCLAIMS AND EXCLUDES ANY AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Buyer agrees that its SOLE AND EXCLUSIVE REMEDY against Wisco and Wisco s SOLE AND EXCLUSIVE LIABILITY arising out of any defect or nonconformity in the product shall be replacement/exchange of such nonconforming countertop food service equipment at Wisco s expense. No countertop food service equipment shall be returned without Wisco s consent. IT IS AGREED THAT WISCO S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE SALE PRICE FOR THE COUNTERTOP EQUIPMENT CLAIMED TO BE DEFECTIVE OR NONCONFORMING. Without limiting the generality of the foregoing, SUCH WARRANTIES DO NOT COVER: Glass, plastic enclosures/panels, door assemblies, light bulbs & wire pizza oven heating elements. SHIPPING DAMAGE If the outside packaging of your order is visibly dented, crushed, torn or otherwise significantly damaged, or if you move the carton and you hear broken glass, please reject the shipment while driver is still with you if possible. Please call us at (800)999-4726 or email contact@wiscoind.com to notify us of the issue. We will confirm the damage with the carrier and re-ship your order immediately. RETURN POLICY You may return any unused, undamaged items within 30 days of receipt. We will issue a refund in the form of your original payment, less a 20% re-stock fee. All returns must be received in resalable condition. Wisco Industries will not accept a return with shipping damage. Wisco Industries will not reimburse any shipping and handling fees. If you would like to return an item please call us at 608-835-3106 or toll free at 1-800-999-4726 and ask for our Food Service Equipment Division or you may send an email to us at: contact@wiscoind.com You will be given a return # and return instructions. We can not accept returns without a return #. Please be sure to include a copy of the packing list with the return. Rev. 06-25-14