Instruction Manual and Parts List. Ultra High Speed Overedge and Safety Stitch Machine

Instruction Manual and Parts List Ultra High Speed Overedge and Safety Stitch Machine 32D 3M-04 3M-04 / KS 32M-05 34M-04 24M-24 24M-24 / KS 244M-24 25M-35 25M-35 / KH 25M-55 25M-55 / KH 25M-56 25H-56 / KH 32K 3M-04 3M-04 / KS 32M-05 34M-04 24M-24 24M-24 / KS 244M-24 25M-35 25M-35 / KH 25M-55 25M-55 / KH 25M-56 25H-56 / KH Singer is a registered trademark of The Singer Company Limited or its affiliated companies. 200 Copyright The Singer Company Limited

Contents Safety Instructions. Important Safety Instructions.2 For Safe Operation 2 2 Product Description and Machine Specification 2. Product Description 3 2.2 Machine Specification 4 2.3 Motor, Motor Pulley and V-Belt Specifications 5 3 Mounting and Adjustment Instructions 3. Table Cut-Out Diagram 6 3.2 Machine Installation 7 3.3 Lubrication and Oil Drainage 9 3.4 Fill Silicon Oil to Reservoir 0 3.5 Needle Attachment (or Replacement) 0 3.6 Replacing Upper and Lower Knife 3.7 Machine Threading 2 3.8 Thread Tension Adjustment 3 3.9 Presser foot pressure 4 3.0 Adjusting the Differential Feed Rate 4 3. Stitch Length Adjustment 3.2 Parts Relation and Timing 6 4 Maintenance 4. Machine Head Cleaning 7 7 4.2 Oil Change and Filter Cleaning 7 4.3 Safety Inspection 7 5 Troubleshooting 8 3 6 5

Contents 6 Parts list 2 6. Machine Bed Frame Components 22 6.2 Machine Cover Components () 24 6.3 Machine Cover Components (2) 26 6.4 Crank Shaft Drive Components 28 6.5 Thread Tension Components 30 6.6 Thread Guide and Thread Take-up Components () 32 6.7 Thread Guide and Thread Take-up Components (2) 34 6.8 Thread Guide and Thread Take-up Components (3) 36 6.9 Needle Bar Components () 38 6.0 Needle Bar Components (2) 40 6. Needle Plate and Needle Guard Components 42 6.2 Upper Looper Components 44 6.3 Lower Looper Components 46 6.4 Chain Stitch Looper Components () 48 6.5 Chain Stitch Looper Components (2) 50 6.6 Differencial Feed Components 52 6.7 Feed Dog Components 54 6.8 Knife Drive Components 56 6.9 Presser Foot Components 58 6.20 Lubrication Components () 60 6.2 Lubrication Components (2) 62 6.22 Silicon Oil Reservoir Components 64 6.23 Exclusive Parts List for 32K series 66 6.24 Thread Stand Components 68 6.25 Accessories 70 6.26 Machine Support Plate For Semi-Submerged Components 72 6.27 Specific Parts for 32D-25 Hand 32K-25H 73 6.28 Optional Parts 74 6.29 Back Latch Components 76 6.30 Vacuum Suction & AFL Device (Option parts) 78 6.3 ChainCutter DeviceComponents 80 7 Gauge Parts List 8

Safety Instructions. Important Safety Instructions Important When using the machine, basic safety procedures must be followed. Read with attention all instructions before using the machine. When using it, understand that all basic safety instructions are not limited to the following items. Read all instructions, take care of this manual, and use it as reference when necessary. Before running the machine, make sure all relevant safety specifications are adequate to specifications and technical standards in your country. The machine should not be run without its safety devices. The machine should only be operated by properly trained personnel. For your safety, goggles must be used while running the machine. Turn off or unplug the machine when the following situations arise: Passing the thread by the needle or replacing the bobbin or looper. Replacing the needle, presser foot, throat plate, feed dog and sliding plate. When the machine is in maintenance. When the operator is not running the machine. In case of lubricant oil contact with the eyes or skin, washed the surface with plenty of icy water with a generous amount of cold water. In case of ingestion, seek medical help immediately. Repair, fitting or maintenance should only be performed by properly trained personnel. Maintenance and repair on electric equipment should only be made by qualified personnel. If any electric device is damaged, the machine should be immediately stopped. Before starting the machine in full running, a test must be conducted to assure that machine and operator are able to perform the task. The machine should not be placed next to a sound source as an ultrasonic welding machine and other equipment. The machine should only be run with the proper electric cable and connectors, and also the adequate grounding. The machine should only be used to sew materials as indicated in its instructions manual, and indications of use should be followed. Singer will not be held responsible for any damage caused by unauthorized changes in the product.

.2 For Safe Operation To avoid the risk of electric shock, do not open the motor wiring box and do not touch the components assembled inside the wiring box. To avoid injuries do not run the machine without the belt cover or in case any other safety device is removed. To avoid possible injuries keep fingers, head and clothes far from wheel, belt and motor when the machine is running. Nothing should be placed near those parts. To avoid injuries never put your fingers next to the rotating hook and the thread take-up lever cover when the machine is running. To avoid possible injuries be careful when putting down or lifting the machine head. To avoid accident in case of a sudden start of the machine always turn it off when laying it down, or remove the belt cover and the belt. If you machine is equipped with a servomotor, it does not make noises while being driven.to avoid a possible accident caused by an unexpected start, be sure the machine is turned off. To avoid electrical shock, do not run the machine without proper grounding. To minimize the risk of accidents or damage in electric components caused by electric discharge turn the machine off before unplugging it. Clean the machine periodically. 2

Product Description and Machine Specification 2. Product Description Ultra high speed overedge and safety stitch machines 3

2.2 Machine Specification Table Machine Specification Singer Model Needle Gauge Overedge Bight Stitch Length Presser Foot Lift Singer Speed Differential Rate Application [mm] [mm] [mm] [mm] Needle Cat [spm] 32D-3M-04 4 620-06 75/ 8500 Three-thread overlock machine 32D-3M-04 / KS 4 620-06 75/ 8500 3-32D-32M-05.5 620-06 65/9 8500 Three-thread overlock machine with vertical chain cutter and AFL device Three-thread handkerchief edging (rolled hem) overlock machine 32D-34M-04 4 620-06 75/ 7500 Three-thread back latch overlock machine 32D-24M-24 4 620-06 75/ 7500 Four-thread overlock machine 32D-24M-24 / KS 2 4 2 4 0.7 ~ 2.0 5 620-06 75/ 7500 Four-thread overlock machine with vertical chain cutter and AFL device 32D-244M-24 4 3.8 620-06 75/ 7500 Four-thread back latch overlock machine 32D-25M-35 5 620-06 90/4 7500 Five-thread overlock machine 3 32D-25M-35 / KH 5 620-06 90/4 7500 Five-thread overlock machine with vertical chain cutter and AFL device 32D-25M-55 5 620-06 90/4 7500 Five-thread overlock machine 2 5 Five-thread heavy duty overlock machine with 32D-25M-55 / KH 5 620-06 90/4 7500 horizontal chain cutter and AFL device 5 32D-25H-56 6 620-06 30/2 6500 Five-thread heavy duty overlock machine 0.8~.5 7 Five-thread heavy duty overlock machine with 32D-25H-56 / KH 6 620-06 30/2 6500 horizontal chain cutter and AFL device 32K-3M-04 4 620-06 75/ 8500 Three-thread overlock machine 32K-3M-04 / KS 4 620-06 75/ 8500 3-32K-32M-05.5 620-06 65/9 8500 Three-thread overlock machine with vertical chain cutter and AFL device Three-thread handkerchief edging (rolled hem) overlock machine 32K-34M-04 4 620-06 75/ 7500 Three-thread back latch overlock machine 32K-24M-24 4 620-06 75/ 7500 Four-thread overlock machine 32K-24M-24 / KS 2 4 2 4 0.7 ~ 2.0 5 620-06 75/ 7500 Four-thread overlock machine with vertical chain cutter and AFL device 32K-244M-24 4 3.8 620-06 75/ 7500 Four-thread back latch overlock machine 32K-25M-35 5 620-06 90/4 7500 Five-thread overlock machine 3 32K-25M-35 / KH 5 620-06 90/4 7500 Five-thread overlock machine with vertical chain cutter and AFL device 32K-25M-55 5 620-06 90/4 7500 Five-thread overlock machine 2 5 Five-thread overlock machine with horizontal chain 32K-25M-55 / KH 5 620-06 90/4 7500 cutter and AFL device 5 32K-25H-56 6 620-06 30/2 6500 Five-thread heavy duty overlock machine 0.8~.5 7 Five-thread heavy duty overlock machine with 32K-25H-56 / KH 6 620-06 30/2 6500 horizontal chain cutter and AFL device With Direct Drive Servo Motor With Clutch Motor Needles Threads 4

2.3 Motor, Motor Pulley and V-Belt Specifications 2.3. For 32D series ½ HP 2-pole clutch motor Motor pulley diameter M type v-belt Machine Speed Table 2 Motor Pulley Diameter [mm] [spm] 50Hz 60Hz 5,500 0 90 6,000 5 95 6,500 30 05 7,000 40 5 7,500 50 25 2.3.2 For 32K series Direct drive servo motor and control system. 5

3 Setup and Adjustment Instructions 3. Table Cut-Out Diagram 40 R6 60 R25 R25 3 65 625 65 20 225 20 4 5 25 85 50 95 C-C 55 32 065 475 30 295 40 48 250 47 R24 40 55 B 45 R24 B C C 98 0 240 345 358 B-B 25.5 9 A A 7.95 97.3 A-A 25 3 3 8.5 38 90 550 Figure 6

3.2 Machine Installation Install the machine support components and the cloth waste chute as indicated in Figure 2. In case of semi-submerged assembly, the distance between the needle plate top surface and the table top is around 00 mm. For fullysubmerged assembly, the distance is around 5.0 mm. 3 2 2 6 9 4 0 5 7 8 Figure 2 7

3.2 Machine Installation Mount the machine head over the machine support plate. Connect the machine handwheel to the clutch motor with the v-belt (for 32D only) Adjust the tension of the v-belt so that it can be about 20 mm bent inward when you press the middle of it and make sure the motor turning direction is clockwise, referred to the Figure 3.(for 32D only) 2cm Figure 3 Set the pedal of the clutch motor to the left side and the pedal of the presser foot lift at right side. Install the thread stand referred to the parts list. Install the belt cover according to Figure 4.(for 32D only) Figure 4 8

3.3 Lubrication and Oil Drainage Important As this is a ultra high speed machine, DO NOT run the machine before oiling and assuming the direction of the motor rotation. Remove the rubber plug and fill the lubricant oil (Singer Oil) until the indicator of the oil level between 'L' and 'H' lines of the oil level sight window. After that put back the rubber plug. When using the machine for the first time, or a machine that has not been used for some time, oil the needle bar top, the guides and looper before running it. H L Figure 5a Figure 5b To preserve the machine, change the oil after the four weeks of use. After that, the oil must be changed every six months. To change the oil, simply remove screw indicated on Figure 6. After draining the oil, replace the screw and fill the machine with new oil. This machine has an oil filter that must be cleaned every month or changed as needed. To replace the oil filter, simply remove four screws and remove the top cover indicate on Figure 7. Then remove three screws and remove oil filter cap. Figure 6 Figure 7 9

3.4 Fill Silicon Oil to Reservoir When sewing in ultra high speed, fill the device with silicon oil in order to prevent needle thread breakage and fabric damage. As show on Figure 8. Figure 8 3.5 Needle Attachment (or Replacement) Use only Singer s Cat. 620 needles Loosen screw as indicated on Figure 9 & 0 with the Allen key wrench in the accessory box and insert the needle (or remove the old For needle For 2 needle needle). Insert the needle with its long groove facing towards you and push it up until the bar end.. Tighten screw. Figure 9 (a) OK! Insert the needle to the proper depth. Figure 9 (b) Figure 0 0

3.6 Replacing Upper and Lower Knife Replacing the upper knife. Loosen screw. Move lower knife holder 2 to the extreme left position. Tighten screw temporarily. 2. Remove screw 3 and then upper knife 4. To install a new upper knife, turn the handwheel until the upper knife holder reaches the lowest position of its stroke. Overlap the cutting edges of the upper anb lower knives by 0.5~.0 mm according to the overedge width (Figure ). 3. Overlap the cutting edges of the upper and lower knives so that midpoint A on upper knife 4 and the midpoint of lower knife 6 are crossed (Figure 2). Loosen screw. Make sure the upper and lower knives mate positively. Then tighten screw. 4. Place a thread between the upper and lower knives. Check the cutting by turning the handwheel. 4 2 4 3 Figure 8 5 6 7 Replacing the lower knife. Loosen screw. Move lower knife holder 2 to the extreme left position. Tighten screw temporarily. 2. Loosen screw 5 and remove lower knife 6. Install a new knife by referring to "Replacing the upper knife procedures 3 and 4. To install a new lower knife, the cutting edge of the lower knife should be flush with the top surface of the needle plate. 4 0.5~.0mm 6 Figure 2 (a) Top surface of the needle plate Adjusting overedge width I. Loosen screw move lower knife holder 2 all the way to the left and then tighten the screw temporarily. 2. Loosen screw 7 move upper knife clamp 8 left or right as required. Install upper and lower knives by referring to "Replacing the upper knife" procedures 3 and 4. 6 4 Figure 2 (b) A Top surface of the needle plate

3.7 Machine Threading 3.7. Easy Threading Method Important Refer to the sewing type you need for correct threading. Any incorrect threading may cause thread brake, uneven stitches or skip stitches. Open three covers. Move the presser foot aside. Knot the preset thread and the thread being used together to thread the machine. 2 Needle thread Trim the knots off neatly before passing through the eye of the needle to rethread. 3 Make sure the machine is threaded correctly by referring to the threading diagram. 4 Looper thread Trim the knots off neatly after passing through the yey of the looper. 3.7.2 Threading Diagram For three / four thread machine Figure 3 For five thread machine Figure 4 Figure 5 2

3.8 Thread Tension Adjustment Important The thread tension should be adjusted according to the type and thickness of the cloth, sewing thread, sewing width, stitch length and others. Therefore the pressure of the tension nuts or thread guides should be individually adjusted for each case. The following adjustments are related to Figure 6 &7. Tension Nut : controls the needle thread or the left thread in case of two needles. Tension Nut 2: controls the thread in the right needle. Tension Nut 3: controls the thread in the lower looper. Tension Nut 4: controls the thread in the lower looper. Tension Nut 5: controls the thread of the safety stitch. 3 3 2 2 Figure 6 3 3 4 4 4 5 2 2 4 To loosen To tighten 2 3 Figure 7 3

3.9 Presser foot pressure Loosen adjusting nut of Figure 8 and turn adjusting bar 2 to adjust the presser foot pressure.it should be as light as possible to be sufficient to obtain the proper stitch formation. 2 Light Heavy Figure 8 3.0 Adjusting the Differential Feed Rate The differential feed ratio is the ratio of movements between the main feed dog and differential feed dog. When the movement of main feed dog is bigger than the differential feed dog, the fabric is stretched at sewing. Otherwise the fabric will be shrunk. Loosen the adjusting nut and turn the adjusting nut 2 to adjust the differential feed ratio. As shown on Figure 9. To shrink 2 To stretch Figure 9 4

3. Stitch Length Adjustment Important The stitch length adjustment is made according to the sewing fabric, differential feed ration and other factors. Press button to the end and keep it pressed as shown on Figure 20. Turn the handwheel until we have the desired stitch length. It is shown on the handwheel scale. Aligning Mark Coarse Fine Handwheel Push Button Figure 20 5

3.2 Parts Relation and Timing 3,4 Thread 5 Thread (b) (c) (e) (d) (a) Top surface of the needle plate (a) Figure 2 Figure 22 Figure 23 (g) Top surface of the needle plate (h) (f) Figure 25 Top surface of the needle plate Figure 24 Figure 26 Figure 27 Upper looper Feed dog Model 32D & 32K Height of needle (Figure 2) Lower looper left limit position (Figure 22) Upper looper left limit position ( c ) (Figure 23) Height of upper looper ( c ) (Figure 23) Upper looper holder left limit position (e) (Figure 23) Upper looper holder install direction Chain looper left limit position (f) (Figure 24) Height of feed dog (g) (Figure 25) Height of auxiliary feed dog (h) (Figure 27) Feed eccentric -3M-04 0.5 3.8 4.4~4.7 0.8 4.5 Left - 0.8 0.5 0.35~2.0-3M-04 / KS 0.5 3.8 4.4~4.7 0.8 4.5 Left - 0.8 0.5 0.35~2.0-32M-05 0.5 3.8 4.4~4.7 0.8 4.5 Left 0.6~0.7 0.3 0.35~.7-34M-04 0.5 3.8 5.4~5.7 0.5 3.5 Right - 0.8 0.5 0.35~.7-24M-24 0.5 3.8 5.4~5.7 0.5 3.5 Right - 0.8 0.5 0.35~2.0-24M-24 / KS 0.5 3.8 5.4~5.7 0.5 3.5 Right - 0.8 0.5 0.35~2.0-244M-24 0.5 3.8 5.4~5.7 0.5 3.5 Right - 0.8 0.5 0.35~2.0-25M-35 0.5 3.8 4.4~4.7 0.8 4.5 Left.5 0.8 0.5 0.35~2.0-25M-35 / KH 0.5 3.8 4.4~4.7 0.8 4.5 Left.5 0.8 0.5 0.35~2.0-25M-55 0.5 3.8 4.4~4.7 0.8 4.5 Left.5 0.8 0.5 0.35~2.0-25H-55 / KH 0.5 3.8 4.4~4.7 0.8 4.5 Left.5 0.8 0.5 0.35~2.0-25H-56.9 4.2 5.0~5.3 2 4.5 Left.7 0.8 0.5 0.35~2.0-25H-56 / KH.9 4.2 5.0~5.3 2 4.5 Left.7 0.8 0.5 0.35~2.0 6

4 Maintenance 4. Machine Head Cleaning Clean the machine periodically with a soft and dry cloth to remove the excess of dust on the machine head. Do not use any kind of lacquer thinner to wipe the surface. Figure 28 4.2 Oil Change and Filter Cleaning 4.3 Safety Inspection When Machine is running, oil will be sprayed into the oil window. If no oil sprayed, please check oil level (see topic 3.3) If the machine was idle for a long time, oil the top of the needle holder, guides and looper guides before resuming the operation. The oil should be changed every four months. To replace the oil, follow the instructions of topic 3.3. The oil filter should be cleaned every month or replaced by a new one as necessary. To clean or replace the oil filter, follow the instructions of topic 3.3. Frequently check if all safety devices are properly installed and adjusted. Check all screws that fix and hold the machine head that should be properly tight. OK! (Operating) Figure 29 Check and be sure the V-belt is not excessively worn out and see that it has the proper tension (Except 32K) Check and be sure there is no motor overheating and be sure that the cable and electric connector are not damaged. 7

Troubleshooting Problems Possible Causes Possible Solutions. Needle installed the wrong way.. Install the needle correctly. 2. Wrong kind of needle. 2. Use needle adequate for cloth and thread. Broken needle 3. Damaged needle. 3. Replace for a new one. 4. Wrong relation with needle guards. 4. Adjust needle guards. 5. Wrong relation with looper. 5. Adjust the looper. 6. Needle is not centralized with the hole at the needle plate or the presser foot. 6. Adjust the needle plate or the presser foot.. Low quality thread.. Use good quality thread. 2. Thread is thicker than the eye of the needle. 2. Use adequate needle to cloth and thread. 3. Wrong passage of thread. 3. Pass thread correctly. 4. Thread tension too tight. 4. Adjust the thread tension unit. Broken thread 5. Needle wrongly set. 5. Set needle correctly. 6. Thread stand wrongly set. 6. Set the thread stand correctly. 7. Needle overheating. 7. Fill in silicon oil or adjust needle guards. 8. Tension disk or guides with burrs. 8. Replace the parts. 9. Wrong relation of needle with looper. 9. Adjust the synchronism of needle and looper. 0. Needle, looper, needle plate and guides have burrs. 0. Replace the part.. Wrong relation of needle with looper.. Adjust the relation of needle with looper. 2. Wrong passage of thread. 2. Pass thread correctly. 3. Needle installed the wrong way. 3. Install needle correctly. Skip stitches 4. Inadequate tension of thread. 4. Adjust thread tension button. 5. Point of looper damaged. 5. Replace the part. 6. Needle damaged. 6. Replace for a new needle. 7. Wrong installation of needle guards. 7. Adjust the needle cover.. Wrong threading.. Pass thread correctly. 2. Thread is thicker than needle hole. 2. Use proper needle hole for cloth and thread. Failure in stitches 3. Wrong thread tension. 3. Adjust the thread tension units. 4. Needle thread is not lubricated. 4. Fill in the silicon oil. 5. Wrong relation of needle with looper. 5. Adjust the needle and looper. 8

Troubleshooting Problems Possible Causes Possible Solutions. Wrong threading.. Threading correctly. 2. Wrong installation of thread stand. 2. Install thread support correctly. 3. Wrong setting of lower knfe. 3. Adjust lower knife correctly. Uneven Stitches 4. Knives does not cut perfectly. 4. Adjust or replace knives. 5. Thread guide or tension disc with burrs. 5. Replace the part. 6. Needle point damaged. 6. Replace the needle. 7. Inadequate height of feed dog. 7. Adjust the height of feed dog. 8. Inadequate thread tension. 8. Adjust thread tension.. Thread tension is too strong.. Adjust thread tension. 2. Inadequate pressure on presser foot. 2. Adjust pressure on presser foot. Puckering 3. Inadequate height of feed dog. 3. Adjust the height of feed dog. 4. Knives does not cut perfectly. 4. Adjust or replace knives. 5. Differential feed is not correct. 5. Adjust differential feed ratio. 6. Needle is too thick. 6. Use proper needle to cloth and thread.. Incorrect presser foot.. Adjust presser foot correctly. 2. Inadequate synchronism of lopper cam. 2. Adjust looper cam. 3. Chain stitch looper installed wrongly. 3. Adjust looper correctly. Poor chain-off stitches 4. Wrong passage of thread. 4. Pass thread correctly. 5. Thread tension inadequate. 5. Adjust thread tension. 6. Wrong relation of needle with looper. 6. Adjust relation of needle with looper. 7. Needle plate or presser foot with burr. 7. Replace the part. 8. Rough thread tension disc. 8. Polish thread tension disc. 9

Parts list

6. Machine Bed Frame Components 4 2 3 2 6 9 5 8 7 0 22

6. Machine Bed Frame Components No. Part No. Description Qty 3thread 4thread 5thread P0300 Pin 2 P0307 Pin 3 20700 Indicator guide 2 2 2 4 2073027 Pipe 2 2 2 5 P0308 Pin 6 20628023 Plug 0 7 2070002 Bracket Assembly 8 207S3003 Screw 2 2 2 9 206S3000 Bed pin 4 4 4 0 P0309 Pin 202600 Pin 2 20726009 Pin (for 32D-25H only) 0 0 23

6.2 Machine Cover Components () 5 40 6 2 39 3 4 3 2 37 5 7 40 6 7 38 29 28 0 9 34 8 24 26 27 30 3 35 25 2 33 40 36 38 32 8 22 9 20 23 24

6.2 Machine Cover Components() No. Part No. Description Qty 3 thread 4 thread 5 thread 2070003 Top cover 2 207S02 Screw 4 4 4 3 2072200 Gasket 4 20622003 Cushion rubber 3 3 3 5 207002 Oil sight window 6 20722002 Plug 7 2070004 Side cover 8 207S02 Screw 2 2 2 9 207S008 Screw 2 2 2 0 20702000 Presser bar 2072043 Front cover (left) 0 0 2 207S700 Screw 4 4 4 3 207003 Belt cover assembly 5 S003 Screw 3 3 3 6 207200 Fan cover 7 207S007 Screw 8 2070005 Front cover (right) 9 2070006 Hinge 20 207S008 Screw 3 3 3 2 2062600 Pin 22 207S400 Screw 2 2 2 23 2062700 Spring 24 2072002 Latch 25 207S009 Screw 26 207S4002 Screw 27 207S4003 Screw 28 2072003 Latch 29 207S003 Screw 30 2062004 Flat spring 3 S003 Screw 32 2072004 Front cover (left) 0 33 207S0 Screw 2 2 2 34 2072005 Side cover 35 20737006 Threading diagram 36 20737007 Threading diagram 0 0 37 J9002-00 Singer S cameo 38 J90032-0XX Model plate 2 2 2 39 J9002-002 Singer resin plate 40 R0300 Revit 6 6 6 25

6.3 Machine Cover Components (2) 34 33 35 37 36 26 27 25 24 3 32 30 29 28 2 38 39 8 40 23 9 8 7 6 3 7 4 5 6 4 3 5 22 2 20 9 0 2 26

6.3 Machine Cover Components (2) No. Part No. Description Qty 3 thread 4 thread 5 thread 207204400 Cloth plate 0 0 2 207200600 Cloth plate 0 3 2070300 Bushing 4 207S400 Screw 5 W02004 Washer 6 30228008 Washer 7 207S0 Screw 8 20622003 Cushion rubber 9 20708 Side cover (Wide) 0 0 0 207004 Side cover (Narrow) 0 207S03 Screw 2 W02002 Spring washer 3 207S0 Screw 2 2 2 4 2052807 Washer 2 2 2 5 20622003 Cushion rubber 6 206206 Latch 7 207S04 Screw 8 2072008 Plate 9 207S7003 Screw 2 2 2 20 2072009 Lever 2 207S2000 Screw 22 2072700 Spring 23 2070900 Bracket 24 207200 Fabric guide 25 207S007 Screw 2 2 2 26 207005 Eye guide 0 27 20709 Eye guide 0 0 28 207S05 Screw 2 2 2 29 W00 Washer 2 2 2 30 20720 Bracket 3 207S20002 Screw 32 20628022 Washer 2 2 2 33 2070007 Bed cover plate assembly 34 207S200 Screw 5 5 5 35 20722003 Gasket 36 20720200 Cover plate 37 207S02 Screw 4 4 4 38 207S06 Screw 39 N000 Nut 40 022020 Oil Reservoir Cushion 27

6.4 Crank Shaft Drive Components 30 3 29 0 2 2 3 9 8 3 4 4 5 6 5 7 8 9 28 6 7 32 4 5 27 26 33 24 25 23 20 2 22 28

6.4 Crank Shaft Drive Components No. Part No. Description Qty 3 thread 4 thread 5 thread 2070200 Crankshaft 2 20702050 Crankshaft (for 32D-25H / 32K-25H only) 0 0 3 20628007 Washer 4 4 4 4 2070008 Blance weight 2 2 2 5 207S07 Screw 4 4 4 6 20726002 Pin 7 S0009 Screw 0 8 207203 Cover 0 9 207S007 Screw 3 3 0 0 00024 O Ring B04004 Ball bearing assembly 2 207S08 Screw 3 207S4006 Screw 4 2072900 Ring 5 B002 Ball bearing 6 B04005 Ball bearing 7 W03003 Washer 4 4 4 8 2003002 Oil seal 9 00025 O ring 20 00028 O ring 2 20708002 Right cover 22 207S02 Screw 3 3 3 23 2070900 Fan assembly 24 207350022 Machine pulley 25 S0009 Screw 2 2 2 26 207S3004 Screw 27 W02004 Spring washer 28 20602002 Pin 0 0 29 2072046 Cover 0 0 30 207S700 Screw 0 0 2 3 207S02 Screw 0 0 32 20708003 Spacer 33 2070009 Cover 29

6.5 Thread Tension Components 7 7 6 6 5 5 4 6 4 8 8 3 3 9 8 7 7 6 6 5 9 5 4 7 4 0 0 3 3 2 20 For -needle 4 2 7 3 9 5 For 2-needle 4 7 2 3 9 6 30

6.5 Thread Tension Components No. Part No. Description Qty 3 thread 4 thread 5 thread 20700400 Tension spring assembly 3 30006 Rachet 3 4 4 4 300052 Cup 3 4 4 5 302806 Tension disc 6 8 8 6 20623008 Felt 3 4 4 7 20S3006 Screw stud 3 4 4 8 207270 Spring 2 2 9 20700500 Tension spring assembly 0 302703 Spring 2 2 2 207300 Thread guide 2 207S007 Screw 2 2 2 3 207205 Thread guide 4 2062052 Tension guide 3 4 4 5 207S004 Screw 0 0 6 20700300 Tension spring assembly 0 7 20700700 Tension spring assembly 8 30S60062R Knob (red dot) 9 30S60062Y Knob (Yellow dot) 0 20 30S60062B Knob (blue dot) 2 30S60062G Knob (Green dot) 3

6.6 Thread Guide and Thread Take-up Components () 9 2 For 5-thread 8 3 6 6 5 7 0 2 4 5 3 7 8 9 20 22 2 4 32

6.6 Thread Guide and Thread Take-up Components () No. Part No. Description Qty 3thread 4thread 5thread 2070029 Bracket 0 0 2 207S09 Screw 0 0 2 3 2073020 Thread guide (for 32D-25H / 32K-25H only) 0 0 4 2073052 Thread take-up (for 32D-25H / 32K-25H only) 0 0 5 207S400 Screw 0 0 6 2070030 Bracket 0 0 7 S003 Screw 0 0 8 207302 Thread guide 0 0 9 207S400 Screw 0 0 0 2073022 Thread guide (except 32D-25H / 32K-25H) 0 0 207S05 Screw (for 32D-25H / 32K-25H only) 0 0 2 2 2073050 Thread guide (for 32D-25H / 32K-25H only) 0 0 3 S003 Screw 0 0 4 2073023 Thread guide (except 32D-25H / 32K-25H) 0 0 5 207305 Thread guide (for 32D-25H / 32K-25H only) 0 0 6 S003 Screw 0 0 7 2073006 Bracket 0 0 8 2073007 Thread retainer 0 0 9 207S20003 Screw 0 0 20 20727002 Spring 0 0 2 2073024 Thread take-up (except 32D-25H / 32K-25H) 0 0 22 207S05 Screw (except 32D-25H / 32K-25H) 0 0 2 33

6.7 Thread Guide and Thread Take-up Components (2) For 3-thread and 4-thread 9 4 5 3 6 7 2 0 3 2 8 4 5 34

6.7 Thread Guide and Thread Take-up Components (2) No. Part No. Description Qty 3thread 4thread 5thread 2073002 Thread guide 0 0 2 2073003 Thread guide 0 0 3 207S400 Screw 0 4 207000 Bracket 0 5 207S09 Screw 0 6 2073004 Thread eyelet 0 0 7 2073005 Thread eyelet 0 0 8 207S05 Screw 2 2 0 9 207S09 Screw 0 0 2073006 Bracket 0 2073007 Thread retainer 0 2 207S20003 Screw 0 3 20727002 Spring 0 4 2073008 Thread take-up 0 0 5 2073009 Thread take-up 0 0 35

6.8 Thread Guide and Thread Take-up Components (3) 0 9 5 2 4 3 2 5 6 6 2 4 7 8 3 36

6.8 Thread Guide and Thread Take-up Components (3) No. Part No. Description Qty 3thread 4thread 5thread 207206 Bracket 2 20305 Thread guide 2 2 2 3 20S006 Screw 2 2 2 4 W00 Washer 2 2 2 5 207300 Thread take-up 6 207S007 Screw 7 20730 Thread eyelet 8 207S020 Screw 9 207302 Thread guide 0 2073053 Thread guide (for 32D-25H / 32K-25H only) 0 0 2073054 Thread guide (for 32D-25H / 32K-25H only) 0 0 2 207305 Thread take-up 3 2073055 Thread take-up (for 32D-25H / 32K-25H only) 0 0 4 207S02 Screw 5 207303 Thread guide 37

6.9 Needle Bar Components () 8 9 0 5 6 3 7 4 25 2 3 6 5 4 2 7 9 20 8 22 2 24 23 38

6.9 Needle Bar Components () No. Part No. Description Qty 3 thread 4 thread 5 thread 2070500 Connection assembly 2 207806 Screw 2 2 2 3 20626003 Pin 4 20784007 Screw 5 2070400 Crank assembly 6 S0508 Screw 7 20702002 Shaft 8 20708004 Collar 9 2078400 Screw 2 2 2 0 2062804 Washer H05008 Ring 2 2070400200 Lever assembly 3 20782002 Screw 4 2072600300 Shaft assembly 5 20726003 Shaft 6 20523005 Oil wick 7 207200300 Needle bar bushing assembly 8 20702003 Needle Bar 9 2070302 Bushing 20 20784008 Screw 2 00026 O ring 22 20723003 Oil felt 23 20708005 Ring assembly 24 2078023 Screw 25 20722004 Plug 39

6.0 Needle Bar Components (2) For 3 thread 3 4 2 5 For 4 thread 9 0 7 8 6 For 5 thread 2 3 4 5 40

6.0 Needle Bar Components (2) No. Part No. Description Qty 3 thread 4 thread 5 thread XXXXXXXX Needle holder assembly 0 0 2 207S4009 Screw 0 0 2 3 207307 Thread guide (except 32D-25H / 32K-25H) 0 0 4 207S024 Screw 0 0 5 XXXXXXXX Needle 0 0 2 6 XXXXXXXX Needle 0 2 0 7 XXXXXXXX Needle holder assembly 0 0 8 207S4009 Screw 0 2 0 9 207308 Thread guide 0 0 0 207S024 Screw 0 0 XXXXXXXX Needle holder assembly 0 0 2 207S4009 Screw 0 0 3 2073038 Thread guide 0 0 4 207S024 Screw 0 0 5 XXXXXXXX Needle 0 0 4

6. Needle Plate and Needle Guard Components For 5-thread 2 7 6 5 4 3 8 9 5 4 6 7 8 9 3 0 2 For 3-thread / 4-thread 2 20 26 25 24 23 22 28 27 29 3 30 32 42

6. Needle Plate and Needle Guard Components No. Part No. Description Qty 3 thread 4 thread 5 thread XXXXXXXX Needle plate 0 0 2 207S7003 Screw 0 0 2 3 20709002 Bracket (Front) 0 0 4 207S007 Screw 0 0 2 5 20622003 Cushion rubber 0 0 2 6 20709003 Bracket (Rear) 0 0 7 207S007 Screw 0 0 2 8 XXXXXXXX Needle guard (Front) 0 0 9 S0027 Screw 0 0 2 0 XXXXXXXX Needle guard (Rear) 0 0 207S2005 Screw 0 0 2 W03004 spring 0 0 3 207S002 Screw 0 0 4 XXXXXXXX Needle guard (Front) 0 0 5 207S007 Screw 0 0 6 XXXXXXXX Needle guard (Rear) 0 0 7 S0027 Screw 0 0 2 8 2070033 Bracket 0 0 9 207S003 Screw 0 0 2 20 XXXXXXXX Needle plate 0 2 207S7003 Screw 2 2 0 22 20709002 Bracket (Front) 0 23 207S007 Screw 2 2 0 24 20622003 Cushion rubber 2 2 0 25 20709003 Bracket (Rear) 0 26 207S007 Screw 2 2 0 27 XXXXXXXX Needle guard (Front) 0 28 207S007 Screw 0 29 XXXXXXXX Needle guard (Rear) 0 30 207S2005 Screw 0 3 W03004 spring 0 32 207S002 Screw 0 43

6.2 Upper Looper Components 9 0 8 7 2 3 3 4 5 6 2 29 25 26 30 28 32 3 27 22 20 2 9 6 8 4 5 7 44

6.2 Upper Looper Components No. Part No. Description Qty 3 thread 4 thread 5 thread 20705002 Connection assembly 2 207S06 Screw 2 2 2 3 207S005 Screw 2 2 2 4 20704003 Crank assembly 0 0 5 20704004 Crank assembly 0 6 S0508 Screw 7 20702004 Shaft 8 20628006 Washer 9 207S004 Screw 0 20628005 Spring washer 20708006 Spacer 0 0 2 2062209 Oil Seal 3 20708007 Spacer 0 4 20705003 Lever assembly 5 207S2002 Screw 6 20726004 Pin assembly 7 20523005 Oil wick 8 207S400 Screw 9 20704005 Upper looper holder assembly 20 20623005 Felt 2 207S025 Screw 22 XXXXXXXX Upper looper 25 207S026 Screw 2 2 2 26 2075007 Cover 27 207S7004 Screw 28 207S027 Screw 29 202302 Oil wick 30 20723005 Felt 3 207207 Bracket 32 207S020 Screw 45

6.3 Lower Looper Components 2 3 4 5 3 7 2 0 8 5 4 6 8 9 7 6 46

6.3 Lower Looper Components No. Part No. Description Qty 3 thread 4 thread 5 thread 20705002 Connection assembly 2 207S06 Screw 2 2 2 3 207S005 Screw 2 2 2 4 20704006 Crank assembly 0 5 S0508 Screw 0 6 20702004 Shaft 7 20628006 Washer 8 207S004 Screw 9 20628005 Spring washer 0 2062209 Oil seal XXXXXXXX Lower looper 2 207S4006 Screw 0 0 3 207S028 Screw 4 20704007 Lower looper holder assembly 5 207S20004 Screw 6 207S500 Screw 7 2070403 Crank assembly 0 0 8 S0508 Screw 0 0 47

6.4 Chain Stitch Looper Components () 8 0 9 7 2 4 6 5 3 3 2 5 8 9 2 20 4 6 7 28 26 22 27 24 23 25 29 48

6.4 Chain Stitch Looper Components () No. Part No. Description Qty 3 thread 4 thread 5 thread 20705006 Connection 0 0 2 B08002 Needle bearing 0 0 3 2070404 Crank 0 0 4 2070303 Bushing 0 0 5 207S2003 Screw 0 0 6 30228008 Washer 0 0 7 2070907 Slider 0 0 8 207S3009 Screw 0 0 9 2062800 Washer 0 0 0 20628005 Spring washer 0 0 2070008 Pin 0 0 2 00027 O ring 0 0 3 2062607 Shaft 0 0 4 2070034 Holder assembly 0 0 5 S0508 Screw 0 0 6 2070405 Crank assembly 0 0 7 S0508 Screw 0 0 8 20705008 Link 0 0 9 2070303 Bushing 0 0 20 207S2003 Screw 0 0 2 30228008 Washer 0 0 22 2070208 Shaft 0 0 23 305220700 Oil seal 0 0 24 XXXXXXXX Chain stitch looper 25 207Sl028 Screw 0 0 26 2070035 Chain stitch looper holder assembly 0 0 27 207S20004 Screw 0 0 28 20728002 Spacer 0 0 29 207S500 Screw 0 0 49

6.5 Chain Stitch Looper Components (2) 4 2 4 3 7 6 5 4 8 9 0 20 5 22 6 7 2 3 2 9 8 50

6.5 Chain Stitch Looper Components (2) No. Part No. Description Qty 3 thread 4 thread 5 thread 2073039 Thread guide 0 0 2 207S007 Screw 0 0 3 2073040 Thread guide 0 0 4 20629003 Holder 0 0 3 5 2062057 Bracket 0 0 6 207S20002 Screw 0 0 7 20628022 Washer 0 0 8 206S3005 Screw 0 0 9 2062055 Tension disc 0 0 2 0 30206 Spring 0 0 206S6004 Knob 0 0 2 2062056 Thread guide 0 0 3 S003 Screw 0 0 4 20629004 Thread guide 0 0 5 207S020 Screw 0 0 6 206307 Thread guide 0 0 7 207S020 Screw 0 0 8 2062058 Looper thread take-up assembly 0 0 9 207S4009 Screw 0 0 2 20 20629005 Spring 0 0 2 2073026 Thread guide 0 0 22 207S007 Screw 0 0 5

6.6 Differencial Feed Components 23 2 6 8 7 3 4 5 0 9 4 3 2 6 7 8 9 20 5 2 22 26 28 29 25 24 27 30 4 32 3 33 40 42 35 34 36 43 44 37 38 39 52

6.6 Differencial Feed Components No. Part No. Description Qty 3thread 4thread 5thread 20705004 Connection 2 20626003 Pin 3 207S4007 Screw 4 BO800 Needle bearing 5 207000 Eccentric 6 2070002 Guide (Feed eccentric) 7 207208 Flat spring 8 207S4003 Screw 2 2 2 9 2070003 Regulator assembly 0 207S4006 Screw 2 2 2 2070004 Eccentriv assembly 2 20727003 Spring 3 207S20005 Screw 4 20709006 Ratchet 5 20702005 Push button shaft 6 20722005 Gaket 7 00027 O ring 8 2072800 Washer 9 20727004 Spring 20 H0508 Ring 2 20705005 Link 22 207S20006 Screw 23 20629002 Ring 24 20704008 Lever assembly 25 S0508 Screw 26 207209 Lever 27 207S20007 Screw 28 20702006 Shaft 29 2062200 O ring 30 20627006 Spring 3 2072020 Regulator plate 32 207S008 Screw 2 2 2 33 207007 Spacer 2 2 2 34 20760000 Nut 35 207S3000 Screw 36 20728003 Spring washer 37 207S6002 Stopper 2 2 2 38 207S0 Screw 2 2 2 39 30228009 Washer 2 2 2 40 20702007 Adjusting shaft 4 2073700 Label 42 H0508 Ring 43 20727005 Spring 44 20709007 Pin 53

6.7 Feed Dog Components 5 7 8 0 9 3 2 6 2 4 3 26 2 20 7 6 5 2 22 9 22 23 24 25 27 29 28 30 3 35 32 8 4 34 33 36 37 40 38 42 39 4 43 45 44 54

6.7 Feed Dog Components No. Part No. Description Qty 3 thread 4 thread 5 thread 20702008 Shaft 2 H05009 Ring 3 20628023 Plug 4 206280 Washer 2 2 2 5 2070400900 Crank assembly 6 207S3005 Screw 7 2078029 Screw 2 2 2 8 2070900 Block 9 207040 Crank assembly 0 S0508 Screw 2070005 Pin 2 N0004 Nut 3 2062800 Wsher 4 2070006 Pin 5 207S300 Screw 6 20722006 Gasket 7 20729002 Ring 8 026 O ring 9 207090 Block 20 20708008 Collar 2 2 2 2 207S400 Screw 2 2 2 22 20705008 Link 23 2070303 Bushing 24 207S2003 Screw 25 30228008 Wsher 26 207060000 Main feed dog bar 27 XXXXXXXX Main feed dog assembly 28 XXXXXXXX Main feed dog 29 XXXXXXXX Auxiliary feed dog 30 2078029 Screw 3 80029 Screw 32 20706002 Differentrial feed dog bar 33 XXXXXXXX Differentrial feed dog 34 207Sl030 Screw 35 2070902 Block 36 20700 Feed bar guide (Right) 37 207S3006 Screw 2 2 2 38 207002 Feed bar guide (Left) 39 207S3006 Screw 2 2 2 40 207003 Feed bar guide oil seal 4 20722007 Oil seal 2 2 2 42 207S3007 Screw 2 2 2 43 2072003 Tube 44 2072055 Clamp 0 45 207Sl0 Screw 55

6.8 Knife Drive Components 7 3 4 5 6 2 8 9 0 3 For 32D-25H / 32K-25H 7 6 22 9 8 4 5 2 27 23 24 26 For 32D-25H / 32K-25H 29 36 37 38 33 28 35 34 30 3 32 56

6.8 Knife Drive Components No. Part No. Description Qty 3 thread 4 thread 5 thread 20705007 Connection assembly 2 207S06 Screw 2 2 2 3 2070402 Crank assembly 0 4 20704030 Crank assembly 0 0 5 S0508 Screw 6 20626003 Pin 7 207S4007 Screw 8 3020800 Collar assembly 9 S0003 Screw 0 20702009 Upper knife lever 3 20726005 Pin 4 207004 Upper knife holder 0 5 2070036 Upper knife holder 0 0 6 207S02 Screw 7 XXXXXXXXX Upper knife 8 S0029 Screw 9 2070050 Angle upper knife holder 0 0 2 XXXXXXXXX Angle upper knife 0 0 22 207S020 Screw 0 0 23 2072053 Angle upper knife gib 0 0 24 207205 Waste guard 0 0 26 S025 Screw 0 0 27 W00 Washer 0 0 28 207005 Lower knife holder 0 29 2070037 Lower knife holder 0 0 30 207S007 Screw 3 207202 Lower knife holder guide 32 207S09 Screw 2 2 2 33 20727006 Spring 34 2072022 Plate 35 207S007 Screw 36 XXXXXXXXX Lower knife 37 2070903 Lower knife clamp 38 207S2004 Screw 57

6.9 Presser Foot Components 6 5 4 7 8 0 2 4 3 9 3 2 5 7 8 28 29 6 27 36 35 34 3 32 33 9 20 30 23 22 2 26 25 24 58

6.9 Presser Foot Components No. Part No. Description Qty 3 thread 4 thread 5 thread 2072023 Lever 2 207S20008 Screw 3 20727007 Spring 4 2072024 Stopper 5 207S02 Screw 2 2 2 6 207S03 Screw 7 N0004 Nut 8 2072025 Link 9 2062030 Lever 0 20608004 Collar assembly S0507 Screw 2 20627009 Spring 3 2070304 Bushing 4 207S06 Screw 5 2070200 Shaft 6 207006 Presser arm 7 2062606 Pin 8 S00 Screw 9 XXXXXXXX Presser foot assembly 20 207S030 Screw 2 2072026 Finge guard 22 2072048 Stopper 23 207S009 Screw 24 207S020 Screw 25 2072027 Flat Spring 26 207S032 Screw 27 2072028 Spring (except 32D-25H / 32K-25H) 28 2070202 Adjusting screw 29 207S6003 Nut 30 2062034 Lever 3 207 S20009 Screw 32 2062700 Spring 33 2072030 Stopper 34 207S007 Screw 35 2069005 Chain cutter 36 207S020 Screw 59

6.20 Lubrication Components () 6 7 4 25 3 4 5 5 2 7 6 2 3 8 2 20 0 22 23 9 8 6 7 24 22 9 20 2 8 60

6.20 Lubrication Components () No. Part No. Description Qty 3 thread 4 thread 5 thread 207200000 Oli pump assembly 2 20725002 Worm wheel 3 207S5002 Screw 2 2 2 4 20700900 Oil distributor assembly 5 2070904 Plug 2 2 2 6 207S30002 Screw 7 206S30009 Joint screw 8 2022033 Washer 0 0 0 9 207S3008 Screw 2 2 2 0 2070025 Tank 207S005 Screw 2 2 2 2 203600 Oli filter 3 2072035 Cover 4 207S007 Screw 3 3 3 5 00028 O ring 6 2063600 Joint 2 2 2 7 206S30009 Joint screw 2 2 2 8 20629002 Clamp 2 2 2 9 30202 Tube 20 2063600 Joint 2 2 2 2 206S30009 Joint screw 2 2 2 22 20629002 Clamp 2 2 2 23 30202 Tube 24 2052009 Joint 2 2 2 25 2072036 Oil guide 6

6.2 Lubrication Components (2) 2 8 20 22 25 23 24 9 3 2 2 5 4 7 6 3 4 5 6 8 7 0 9 62

6.2 Lubrication Components (2) No. Part No. Description Qty 3 thread 4 thread 5 thread 2070000 Oil sight gauge 2 00030 O Ring 3 2070200 Indicator assembly 4 20703 Indicator support 5 207S30002 Screw assembly 2 2 2 6 2070026 Oil reservoir assembly 7 207S3002 Screw 8 2062204 Washer 9 207S3009 Bolt 4 4 4 0 2062808 Washer 4 4 4 20722008 Gasket 2 20725003 Worm 3 207S4006 Screw 4 20626007 Pipe 5 2070905 Ball 6 207S400 Screw 7 202302 Oil wick 8 207200 Pipe assembly 9 207S0 Screw 20 2070906 Ball 2 2 2 2 207S400 Screw 22 207203800 Joint assembly 23 20723007 Felt 24 2062200 O ring 25 2072008 Tube 63

6.22 Silicon Oil Reservoir Components 8 2 7 3 4 5 6 20 2 9 7 0 8 9 22 23 24 6 2 6 5 4 3 25 64

6.22 Silicon Oil Reservoir Components No. Part No. Description Qty 3 thread 4 thread 5 thread 20704 Silicone oil reservoir 2 20705 Cover 3 20723008 Felt 0 4 207905 Felt 0 0 5 2072040 Thread guide 0 6 207309 Thread guide 0 0 7 207S02 Screw 8 2072042 Cover 9 20723009 Oil felt 0 0 0 2072600 Pin 0 0 2070600 Silicone oil reservoir 0 2 20707 Cover 3 207S30003 Screw 4 402303 Oil wick 5 402002 Tube 6 207204 Clamp 2 2 2 7 2070027 Needle thread lubricator 0 8 207S008 Screw 2 2 0 9 2070904 Plug 0 20 20723009 Oil felt 0 2 2072600 Pin 0 22 2070038 Needle thread lubricator 0 0 23 207S007 Screw 0 0 2 24 2070904 Plug 0 0 25 207003000 Silicone oil reservoir 0 0 65

6.23 Exclusive Parts List for 32K series 2 3 5 6 8 4 7 9 0 2 4 3 5 66

6.23 Exclusive Parts List for 32K series No. Part No. Description Qty 3 thread 4 thread 5 thread 2070080 Machine Frame 2 20702023 Crank shaft 3 2072300 Washer 4 20725004 Worm 5 S008 Screw 6 6 6 6 2070803 Helical casing 7 207S4006 Screw 2 2 2 8 2070804 Right cover 9 207S02 Screw 3 3 3 0 2073300400 Direct drive servo motor 4S3000 Screw 4 4 4 2 207026 Motor cover 3 S003 Screw 3 3 3 4 2073505 Hand wheel 5 S0009 Screw 2 2 2 67

6.24 Thread Stand Components 68

6.24 Thread Stand Components No. Part No. Description Qty 3 thread 4 thread 5 thread 3002032 Thread bar (lower) 2 3028024 Washer 2 2 2 3 N0200 Nut 4 300028 Bracket (3 spools) 0 5 300029 Bracket (2 spools) 0 2 6 3002033 Spool pin 3 4 5 7 W02002 Washer 3 4 5 8 300030 Thread guide bar (3 spools) 0 9 30007 Spool tray 3 4 5 0 302304 Cushion 3 4 5 3003044 Spool holder 3 4 5 2 L02004 Screw 2 2 3 028006 Rubber washer 4 20304 Thread stand support 0 5 3002034 Thread bar (upper) 6 3029005 Joint 7 S04002 Screw 4 4 4 8 N0004 Nut 6 6 6 9 30008 Bracket 20 30308 Thread guide bar 2 S04003 Screw 22 30003 Thread guide bar (2 spools) 0 2 23 30009 Bracket 24 S04004 Screw 3 3 3 25 N0005 Nut 7 8 9 26 30309 Thread guide bar (5 holes) 28 3003045 Thread guide hole 3 4 5 29 3022027 Rod cap 30 203023 Screw 3 203024 Screw 32 3022027 Nut 69

6.25 Accessories 0 7 2 3 6 2 3 7 8 4 5 9 8 20 6 2 5 4 9 70

6.25 Accessories No. Part No. Description Qty 3 thread 4 thread 5 thread 03005 Dust cover 2 203037 Oil bottle 3 203038 Small oil bottle 4 620-06 Needle 3 3 3 5 2069003 Lower knife 6 20304 Spanner (6mm) 7 203042 Spanner (7mm) 8 203043 Spanner (8mm) 9 203044 Allen key driver (.5mm) 0 303026 Allen key (8mm) 203046 Allen key (2mm) 2 203047 Allen key (5mm) 3 30302 Allen key (4mm) 4 03004 Screw driver (small) 5 03003 Screw driver (middle) 6 20305 Tweezers 7 203056 Allen key (6mm) 8 203039 Funnel 9 203054 Foot controller chain 20 203600 Oil filter 2 03002 Screw driver (big) 7

6.26 Machine Support Plate For Semi- Submerged Components 3 2 2 6 9 4 0 5 7 8 No. Part No. Description Qty 3 thread 4 thread 5 thread 2070028 Machine support plate 2 20722009 Cushion rubber 4 4 4 3 30S6008 Nut 4 4 4 4 203029 Washer 6 6 6 5 30S3007 Screw 4 4 4 6 203030 Spacer 4 4 4 7 203032 Waste chute (upper) 8 203033 Waste chute (lower) 9 203034 Screw 3 3 3 0 20303 Waste chute inlet 203035 Screw 4 4 4 2 302203 Spacer 8 8 8 72

6.27 Specific Parts for 32D-25H and 32K-25H 2 3 6 5 4 8 7 2 9 0 No. Part No. Description 3 thread 4 thread 5 thread XXXXXXXX Presser foot assembly 0 0 2 207S030 Screw 0 0 3 207260 Pin 0 0 3 4 207405 Fabric guard 0 0 5 W0002 Washer 0 0 6 206S08 Screw 0 0 7 2079053 Spring 0 0 8 207S6050 Screw 0 0 9 2072052 Finger guard 0 0 0 207S009 Screw 0 0 2073056 Thread eyelet 0 0 2 2079054 Spring 0 0 Qty 73

6.28 Optional Parts For 32D-3M 32D-24M 32D-25M 32K-3M 32K-24M 32K-25M 4 5 8 2 20 9 3 2 7 6 3 6 2 5 9 0 For 32D-32M 32K-32M Turm down hemming 24 25 23 22 4 74

6.28 Optional Parts No. Part No. Description Qty 3 thread 4 thread 5 thread 2070023 Fabric guard 0 0 2 20205 Cloth plate bracket 3 202052 Hinge guide bracket 4 20S20002 Screw 5 2028027 Spring washer 6 20S6003 Nut 9 2026020 Pin 0 202053 Flat spring 20S0 Screw 2 S000 Screw 3 W02002 Spring washer 4 XXXXXXXXX Presser foot 0 0 5 202056 Edge guide bracket 6 20S200 Bolt 2 2 2 7 2028020 Washer 2 2 2 8 20S00 Screw 9 2028020 Washer 20 202054 Edge guide 0 2 202055 Edge guide 0 0 22 207S033 Screw 0 0 23 207203 Uncurler 0 0 24 207S034 Screw 0 0 25 XXXXXXXXX Presser foot finger 0 0 75

6.29 Back Latch Components For 32D-34M 32D-244M 32K-34M 32K-244M 2 3 4 9 0 8 5 6 7 9 5 4 3 2 6 7 8 9 20 50 9 48 2 5 49 29 30 22 52 23 28 24 25 37 38 39 48 26 27 3 32 33 36 40 4 47 46 44 45 34 35 42 43 76

6.29 Back Latch Components No. Part No. Description Qty 3 thread 4 thread 5 thread 205S6002 Nut 0 2 20528008 Washer 0 3 2052008 Connecting plate 0 4 205S300 Screw 0 5 205S3002 Screw 0 6 205S6003 Nut 0 7 207S005 Screw 2 0 0 8 2073044 Bracket 0 0 9 205S3003 Connecting screw 2 2 0 0 205200900 Thread tension releasing wire assemb 0 0 205S6005 Nut 4 2 0 2 20527006 Spring 0 0 3 205S30009 Screw 0 0 4 206S005 Screw 0 0 5 205S6004 Nut 0 0 6 2052005 Tension support 0 0 7 2052006 Thread tension releasing plate 0 0 8 205S3004 Screw 0 0 9 205S30007 Screw 0 20 2052002 Thread press plate 0 2 S02007 Screw 4 4 0 22 2052004 Knife supporter 0 23 205S30008 Screw 0 24 2052003 Pressing block 0 25 205900 Small knife support 0 26 20527003 Spring 0 27 30S6007 Thread tension nut 0 28 2059002 Knife 0 29 XXXXXXXX Needle plate 0 0 30 XXXXXXXX Needle plate 0 0 3 2070902 Needle plate supporter (front) 0 32 XXXXXXXX Presser foot finger 0 0 33 XXXXXXXX Presser foot finger 0 0 34 XXXXXXXX Feed dog assembly 0 0 35 XXXXXXXX Feed dog assembly 0 0 36 207206500 Cloth plate 0 37 202060 Thread guide plate 0 0 38 20206 Thread tension plate 0 0 39 20S6003 Nut 0 0 40 202062 Frong frame 0 0 4 202063 Thread tension releasing lever 0 0 42 200039 Connector 0 0 43 20S2004 Connector screw 0 0 44 20S4003 Screw 0 2 0 45 20S2003 Screw 0 0 46 202702 Spring 0 0 47 20S2002 Screw 0 0 48 202059 Sleeve 0 0 49 202058 Bracket 0 0 50 2003029 Collar 0 0 5 20S4002 Screw 0 0 52 20S06 Screw 0 2 0 77

6.30 Vacuum Suction & AFL Device (Option parts) 9 2 23 3 4 5 7 5 9 7 20 6 8 4 5 Installation position optional 8 20 9 2 22 2 9 0 6 9 IN OUT 4 OUT 3 For 32D series only For 32K series only 29 28 27 26 25 24 78

6.30 Vacuum Suction & AFL Device (Option parts) No. Part No. Description Qty 3 thread 4 thread 5 thread 207302 Vacuum suction assembly (For 32D only) 2073009 Vacuum suction assembly (For 32K only) (3) (3) (3) 2 207302- Z basket () () () 3 207302-2 Bag connecting cover () () () 4 207302-3 Tube D38x0.7 (2) (2) (2) 5 207302-4 Muffler () () () 6 207302-5 Tube () () () 7 207302-6 Dispenser assembly () () () 8 207302-7 Tube D3x0.7 () () () 9 20730002 Cylinder () () () 0 207302-8 Fabric clippings suction nozzle () () () 207302-9 Pneumatic switch For 32D only) () () () 207300 Pneumatic switch For 32K only) () () () 2 69005 PU tube 3M (D6x4) () () () 3 40730024 Pressure regulator with filter tap () () () 4 40730046 Control switch () () () 5 207302-2 Fabric clippings bag () () () 6 40736024 Adjustable tube connector () () () 7 207302-5 Dispenser bracket () () () 8 207302-6 Pressure regulator bracket Screw () () () 9 207302-9 Screw (0) (0) (0) 20 207302-20 Tube clamp (4) (4) (4) 2 207302-2 Nozzle plate () () () 22 207302-22 Elbow pipe () () () 23 207302-23 Scew (2) (2) (2) 24 2070082 AFL connecting rod 25 207S3009 Screw M5x2 26 207S7007 Screw M6x8 2 2 2 27 207008 AFL bracket 28 2073002 AFL Cylinder 29 207S032 Screw M4x38 4 4 4 79

6.3 Chain Cutter Device Components 2 No. Part No. Description Qty 3 thread 4 thread 5 thread 207206000 Vertical chain cutter device assembly (KS) 0 2 20720600 Horizontal chain cutter device assembly (KH) 0 0 80

7 Gauge Parts List MACHINE MODEL 32D & 32K GAUGE NEEDLE NG SW PLATE MAIN FEED DOG ASSM. MAIN FEED DOG AUX. FEED DOG DIFF. FEED DOG PRESSER FOOT ASSM PRESSER FOOT FINGER UPPER FINGER LOWER LOOPER CHAINSTITCH LOOPER -3M-04 (KS) 4 2075005 20740000 207400 2074002 2074003 207600700 2070022 2077004 2077006-32M-05.5 207500 207400800 2074008 2074020 2074007 20760000 2070043 2077004 2077006-34M-04 4 207509 207402000 207400 2074002 2074003 20760700 2077004 2077006-24M-24 (KS) 2 4 2075002 20740000 207400 2074002 2074003 207600700 207009 2077003 2077006-244M-24 2 4 2075020 207402200 207400 2074002 2074003 20760800 2077003 2077006-25M-35 (KH) 3 5 2075008 207400400 2074004 2074002 2074007 207600600 2077006 2072047 2072047-25M-55 (KH) 5 5 207506 20740700 2074004 2074002 207407 20760500 2077006 2072047 2072047-25H-56 (KH) 5 6 2075050 207405200 2074052 2074002 2074050 207005400 2077006 207705 207705 MACHINE MODEL 32D & 32K GAUGE UPPER KNIFE LOWER KNIFE OVERLOCK NEEDLE GUARD CHAIN STITCHNEEDLE GUARD NEEDLE HOLDER NG SW FLAT KNIFE ANGLE KNIFE FRONT REAR FRONT REAR NEEDLE -3M-04 (KS) 4 2069002 2069003 207700 2077002 2073400 620-06 65/9-32M-05.5 2069002 2069003 207700 2077002 2073400 620-06 75/ -34M-04 4 2069002 2069003 207700 2077002 2073400 620-06 65/9-24M-24 (KS) 2 4 2069002 2069003 207700 2077002 20734002 620-06 65/9-244M-24 2 4 2069002 2069003 207700 2077002 20734002 620-06 75/ -25M-35 (KH) 3 5 2069002 2069003 2077008 2077002 2072045 2070032 20734004 620-06 90/4-25M-55 (KH) 5 5 207900 2069003 2077008 2077002 2072045 2070032 2734004 620-06 75/ -25H- 56 (KH) 5 6 2079050 2070053 2077008 2077002 2072045 2070032 2079056 620-06 32/2 8

Rev.05 - Jun.200 P/N 364337-00 Singer is a registered trademark of The Singer Company Limited or its affiliated companies. 200 Copyright The Singer Company Limited www.singer.com