THIN Lighting System Modular & linear architectural lighting for residential and commercial environments.
2 THIN System Product Guide A PPLICA T I O N S: SUSP E N SI O N Office Lighting Suspended Task Lighting Display Lighting Residential The THIN System includes Suspension, Surface Mount and Task lighting for an integrated, functional, minimal look that fits today s office environments. Hand-finished solid brass feels precise and warm. The combination of a 1/2 diameter profile and fully rotatable Light Segments make this an elegant, low visual impact option for illuminating precious artworks and objects. Beam angle options keep light where it is needed. 3.16.18 W W W. J U N I PER -DESIGN.COM The rotatable Light Segments allow the fixture to aim light on a countertop or work surface, and the beam angle options and high CRI mean the light is focused and high quality. Available in multiple luxury finishes, the all-brass THIN System feels appropriate next to high-end furniture pieces in a residential setting. INFO@J UNIPER -DESIGN.COM + 1 3 4 7-7 9 9-2 9 1 5 6 8 3 3 R D S T, U N I T 1 1 B R O O K LY N, N Y 1 1 2 3 2
FEATURES & BENEFITS: SUSPENSION THIN System Product Guide 3 cutaway showing connectors Magnetic Connectors Slim and elegant, the THIN System Suspension is held by a clever magnetic connector system. This allows for easy installation, long runs, and freely rotatable Light Segments. Direct & Indirect Rotating Segments allow for direct or indirect light from the same fixture. Additional Features: Quality Light 3000K and 90CRI standard with 2700K and 4000K options available 600 lumens per 24 segment 920 lumens per 36 segment Simple Installation Whole-inch spacing, rotatable Light Segments, snap-in magnetic connectors, and 24VDC low-voltage wiring make install easy. Minimal Profile 1/2 [12.7mm] diameter Light Segments allow the fixture to hang lower in the room without obstructing sightlines. This means light where it is needed, creating more intimate, thoughtful spaces. Luxury Finishes & Materials Satin Brass, Satin Nickel, and Black Oxide finishes complement high-end interior construction. Brass and acrylic are sturdy and long-wearing. Configurability Constant-voltage system means multiple Light Segments can be powered from one driver, simplifying system design. Multiple driver options are available to meet most dimming requirements.
TECHNICAL THIN Suspension THIN System Product Guide 4 0.5in [1.2cm] segment 0.7in [1.7cm] connector 24in and 36in Light Segments may be combined in the same fixture Standard max length per fixture is (3) 36 Light Segments 110.8in [281.5cm] For longer runs, please contact Juniper Clear Lens 40 degree beam angle Frosted Lens 90 degree beam angle Ceiling Gripper 0.5in dia Local Driver Canopy 6.5in dia x 2.4in Remote Driver Canopy 5in dia x 0.5in ILLUMINATION 3000K and 90CRI standard 2700K and 4000K options available 24 Segment 600 lm delivered / 8W 36 Segment 920 lm delivered / 12.3W 78 lm/watt with clear acrylic lens 50,000 hrs LED life L80 POWER 24VDC output Class 2 constant voltage driver 120VAC input voltage Contact Juniper for alternate inputs Satin Brass, Black Oxide, Satin Nickel MATERIALS Solid brass, PMMA acrylic CERTIFICATIONS cul Damp Location Rated DIMMING TRIAC/Forward Phase/Leading-edge Juniper recommends Lutron DVCL- 253P dimmers See Power Supply section for details Contact Juniper for alternate requirements MOUNTING 9.8ft (3m) 1/16 aircraft cable, field adjustable 16.4ft (5m) Clear-jacketed 22AWG side-by-side silver, field adjustable SYSTEM RUN Limited by driver wattage only GENERAL INFORMATION Designed by Peter Bristol & Juniper Assembled in USA
THIN System Product Guide 5 BUILD A SPECIFICATION THIN Suspension SERIES FINISH SEGMENTS COLOR TEMP JPR-THES - 0-0 0 0 - - - SAMPLE SKU: JPR-THES-01-000333-30-F-L6A Satin Brass, (3) 36 segments, 3000K, frosted lens, local in-canopy 40W Standard power supply (3 X 9.4W = 28.2W total) SAMPLE SKU: JPR-THES-02-000023-27-C-R5F Black Oxide, (1) 36 segment, (1) 24 segment, 2700K, clear lens, remote 40W Lutron power supply with 5 canopy LOCAL/REMOTE CANOPY POWER SUPPLY CODE DEFINITIONS LOCAL/REMOTE (POWER SUPPLY LOCATION) L Local Power Supply - pre-installed in canopy R Remote Power Supply - separately located near fixture in accessible location, connected via low-voltage Class 2 wiring supplied by electrician, use 5 5 x 0.5 round canopy 01 Satin Brass 02 Black Oxide 03 Satin Nickel SEGMENTS 0 no segment 2 24 inch segment - 600 lm delivered / 8.0W 3 36 inch segment - 920 lm delivered / 12.3W note: each digit represents a single segment, e.g. 000023 is (1) 24 segment and (1) 36 segment Contact Juniper for custom segment lengths COLOR TEMPERATURE 27 2700K 30 3000K 40 4000K C Clear - 40 degree beam angle F Frosted - 90 degree beam angle CANOPY 6 6.5 round canopy (for local power supply) 5 5 x 0.5 round canopy (covers junction box) X no canopy POWER SUPPLY - 24VDC CV OUTPUT A Standard 40W - TRIAC/Forward Phase Dims to 5%, 120 VAC B Standard 20W - TRIAC/Forward Phase Dims to 5%, 120 VAC C Standard 12W - TRIAC/Forward Phase Dims to 20%, 120 VAC note: for best dimming, Standard drivers should be matched to total fixture wattage. Standard drivers are ETL Listed, for remote use enclosure E Lutron 40W Local - TRIAC/Forward Phase Dims to 1%, 120 VAC input F Lutron 40W Remote - UL Listed, TRIAC/Forward Phase Dims to 1%, 120 VAC input note: for 120-277VAC input, Lutron 3-wire/Ecosystem Dimming drivers available (up to 96W) X No power supply Juniper recommends Lutron DVCL-253P dimmers Contact Juniper for alternate dimming requirements Project Type Notes
APPLICATIONS: SURFACE MOUNT THIN System Product Guide 6 Under Cabinet Lighting 45mm Standoffs are perfect for undercabinet applications, unobtrusive and elegant. Retail Display Configurable and extendable low voltage light modules are easily integrated into display settings. High CRI LEDs make products look their best. Picture Light 180mm Standoffs are designed for lighting artwork. Plugin and Low Voltage Direct installation options fit multiple situations. Bathroom Vanity ETL Listed, damp location rated for bathroom vanity use. The Light Segments are infinitely rotatable for perfect light angles.
THIN System Product Guide 7 FEATURES & BENEFITS: SURFACE MOUNT cutaway showing connectors Magnetic Connectors The low-voltage magnetic connectors incorporated into the Light Segments are incredibly functional - the lighting direction can be rotated when the fixture is lit, and they make installation easy and intuitive. Multiple Standoff Heights 45mm, 90mm, and 180mm Standoffs allow for a range of applications, from undercabinet and soffit lighting to retail display, library stacks, and general wall-washing. Additional Features: Quality Light 3000K and 90CRI standard with 2700K and 4000K options available 600 lumens per 24 segment 920 lumens per 36 segment Simple Installation Whole-inch spacing, rotatable Light Segments, snap-in magnetic connectors, and 24VDC low-voltage wiring make install easy. Luxury Finishes & Materials Satin Brass, Satin Nickel, and Black Oxide finishes complement high-end interior construction. Brass and acrylic are sturdy and long-wearing. Rotatable Light Segments The magnetic connectors mean that one fixture can be configured to wash light up, down, or back on the wall. A multiple segment fixture can have segments illuminating different things. Configurability Constant-voltage system means multiple Light Segments can be powered from one driver, simplifying system design. Multiple driver options are available to meet most dimming requirements.
TECHNICAL THIN Surface Mount THIN System Product Guide 8 Standoff Options 7.1in [180mm] 0.5in [1.2cm] 3.5in [90mm] 1.9in [45mm] 1.2in [3.0cm] 24in and 36in Light Segments may be combined in the same fixture Standard max length per fixture is (3) 36 Light Segments 110.8in [281.5cm] For longer runs, please contact Juniper Plug-in Power Supply with RF Remote Control Dimmer, Holder, and Cord Wrap Clear Lens 40 degree beam angle Frosted Lens 90 degree beam angle ILLUMINATION 3000K and 90CRI standard 2700K and 4000K options available 24 Segment 600 lm delivered / 8W 36 Segment 920 lm delivered / 12.3W 78 lm/watt with clear acrylic lens 50,000 hrs LED life L80 POWER 120VAC Input Voltage 24VDC Class 2 Constant Voltage Contact Juniper for alternate inputs Satin Brass, Black Oxide, Satin Nickel MATERIALS Solid brass, PMMA acrylic CERTIFICATIONS cul Damp Location Rated DIMMING TRIAC/Forward Phase/Leading-edge Juniper recommends Lutron DVCL- 253P dimmers See Power Supply section for details Contact Juniper for alternate requirements MOUNTING Wall brackets mount directly to drywall SYSTEM RUN Limited by driver wattage only 2 X 18AWG in-wall rated cable recommended for remote power supply installation GENERAL INFORMATION Designed by Peter Bristol & Juniper Assembled in USA
THIN System Product Guide 9 BUILD A SPECIFICATION THIN Surface Mount SERIES FINISH SEGMENTS STANDOFFS COLOR TEMP JPR-THEW - 0-0 0 0 - - - SAMPLE SKU: JPR-THEW-01-000222-090-30-C-RXC Satin Brass, (3) 24 segments, 90mm standoffs, 3000K, clear lens, remote power supply, no cover plate, 20W power supply (3 x 6.1W = 18.3W total) SAMPLE SKU: JPR-THEW-03-000003-180-27-F-SXG Black Oxide, (1) 36 segment, (1) 24 segment, 180mm standoffs, 2700K, frosted lens, plug-in pwer supply with remote control POWER LOCATION POWER SUPPLY CODE DEFINITIONS 01 Satin Brass 02 Black Oxide 03 Satin Nickel SEGMENTS 0 no segment 2 24 inch segment - 600 lm delivered / 8.0W 3 36 inch segment - 920 lm delivered / 12.3W note: each digit represents a single segment, e.g. 000023 is (1) 24 segment and (1) 36 segment, 0000333 is (3) 36 segments Contact Juniper for custom segment lengths STANDOFF LENGTH 045 45mm Standoffs - for undercabinet 090 90mm Standoffs - for general wall-wash and display 180 180mm Standoffs - for picture lighting COLOR TEMPERATURE 27 2700K 30 3000K 40 4000K POWER LOCATION R Remote Power Supply Location - separately located near fixture in accessible location, connected via low-voltage Class 2 wiring supplied by electrician S Plug-in Power Supply Location - plugs into outlet, includes RF remote control dimmer, and 3 meters of cord - requires X and G below, i.e. -SXG *not available with 045 POWER SUPPLY - 24VDC CV OUTPUT A Standard 40W - TRIAC/Forward Phase Dims to 5%, 120 VAC B Standard 20W - TRIAC/Forward Phase Dims to 5%, 120 VAC C Standard 12W - TRIAC/Forward Phase Dims to 20%, 120 VAC note:for best dimming, Standard drivers should be matched to total fixture wattage. Standard drivers are ETL Listed, for remote use enclosure F Lutron 40W Remote - UL Listed, TRIAC/Forward Phase Dims to 1%, 120 VAC input note: for 120-277VAC input, Lutron 3-wire/Ecosystem Dimming drivers available (up to 96W) G 24VDC 36W Plug-in Power Supply X no power supply Juniper recommends Lutron DVCL-253P dimmers Contact Juniper for alternate dimming requirements C Clear - 40 degree beam angle F Frosted - 90 degree beam angle Project Type Notes
THIN System Product Guide 10 7.1 in (180 mm) Standoff 3.5 in (90 mm) Standoff 1.9 in (45 mm) Standoff Use the following two pages to visualize your desired standoff height. Our drawings are to-scale and easily printable to help envision our three standoff heights. While this page shows a simple 2D to-scale drawing, you can get creative and assemble 3D models from the template shown on the next page.
THIN System Product Guide 11 7.1 in (180 mm) Standoff 3.5 in (90 mm) Standoff 1.9 in (45 mm) Standoff For 3D models, print out this page, cut along seams, fold into place, and hold together with tape. We recommend keeping top and bottom circles connected to cylinder walls for easier assembly. Dark circles mark where light segments connect to the standoffs.
12 THIN System Product Guide A PPLICA T I O N S: P R I M A R I E S Wall-Mounted Lighting The THIN System includes wall-mountable options like the Surface Mount and Primaries for an integrated, minimal look that creates a functional lighting installation. Handfinished solid brass feels precise and warm. Display Lighting The combination of a 1/2 diameter profile and fully rotatable Light Segments make this an elegant, low visual impact option for illuminating precious artworks and objects. Beam angle options keep light where it is needed. 3.16.18 W W W. J U N I PER -DESIGN.COM Suspended Task Lighting The rotatable Light Segments allow the fixture to aim light on a countertop or work surface, and the beam angle options and high CRI mean the light is focused and high quality. Residential Available in multiple luxury finishes, the all-brass THIN System feels appropriate next to high-end furniture pieces in a residential setting. INFO@J UNIPER -DESIGN.COM + 1 3 4 7-7 9 9-2 9 1 5 6 8 3 3 R D S T, U N I T 1 1 B R O O K LY N, N Y 1 1 2 3 2
FEATURES & BENEFITS: PRIMARIES THIN System Product Guide 13 cutaway showing connectors Magnetic Connectors Slim and elegant, the THIN System Suspension is held by a clever magnetic connector system. This allows for easy installation, long runs, and freely rotatable Light Segments. Direct & Indirect Rotating Segments allow for direct or indirect light from the same fixture. Additional Features: Quality Light 3000K and 90CRI standard with 2700K and 4000K options available 920 lumens per 36 600 lumens per 24 segment Simple Installation Whole-inch spacing, rotatable Light Segments, snap-in magnetic connectors, and 24VDC low-voltage wiring make install easy. Minimal Profile 1/2 [12.7mm] diameter Light Segments allow the fixture to hang lower in the room without obstructing sightlines. This means light where it is needed, creating more intimate, thoughtful spaces. Luxury Finishes & Materials Satin Brass, Satin Nickel, and Black Oxide finishes complement high-end interior construction. Brass and acrylic are sturdy and long-wearing. Configurability Constant-voltage system means multiple Light Segments can be powered from one driver, simplifying system design. Multiple driver options are available to meet most dimming requirements.
THIN System Product Guide 14 TECHNICAL THIN Primaries Triangle Suspension 24in nominal - 27.3in [69.3cm] 36in nominal -40.3in overall [102.4cm] 24 - max. 116in [292.1cm] 36 - max. 115in [294.6cm] Clear Lens 40 degree beam angle Frosted Lens 90 degree beam angle Ceiling Gripper 0.5in dia Remote Driver Canopy 5in dia x 0.5in ILLUMINATION 3000K and 90CRI standard 2700K and 4000K options available 24 1800 lm delivered / 24W 36 2760 lm delivered / 36.9W 78 lm/watt with clear acrylic lens 50,000 hrs LED life L80 POWER 24VDC output Class 2 constant voltage driver 120VAC input voltage Contact Juniper for alternate inputs Satin Brass, Black Oxide, Satin Nickel MATERIALS Solid brass, PMMA acrylic CERTIFICATIONS cul Damp Location Rated DIMMING TRIAC/Forward Phase/Leading-edge Juniper recommends Lutron DVCL- 253P dimmers See Power Supply section for details Contact Juniper for alternate requirements MOUNTING (3) 9.8ft (3m) 1/16 aircraft cable, field adjustable 16.4ft (5m) Clear-jacketed 22AWG side-by-side silver, field adjustable SYSTEM RUN Limited by driver wattage only GENERAL INFORMATION Designed by Peter Bristol & Juniper Assembled in USA
THIN System Product Guide 15 BUILD A SPECIFICATION THIN Primaries Triangle Suspension SERIES FINISH CONFIGURATION SEGMENTS COLOR TEMP JPR-THES - 0 - TRI - X X 2 - - - R 5 SAMPLE SKU: JPR-THES-02-TRI-2-27-C-R5A Black Oxide, 24 segments, 2700K, clear lens, remote 40W Lutron power supply OR 3 REMOTE CANOPY POWER SUPPLY CODE DEFINITIONS REMOTE (POWER SUPPLY LOCATION) R Remote Power Supply - separately located near fixture in accessible location, connected via low-voltage Class 2 wiring supplied by electrician, use 5 5 x 0.5 round canopy CANOPY 01 Satin Brass 02 Black Oxide 03 Satin Nickel SEGMENTS 2 24 inch - 1800 lm delivered / 24W 3 36 inch - 2760 lm delivered / 36.9W Contact Juniper for custom segment lengths COLOR TEMPERATURE 27 2700K 30 3000K 40 4000K C Clear - 40 degree beam angle F Frosted - 90 degree beam angle 5 5 x 0.5 round paintable white canopy with 3 grippers (covers junction box) POWER SUPPLY - 24VDC CV OUTPUT A Standard 40W - TRIAC/Forward Phase dims to 5%, 120 VAC note: for best dimming, Standard drivers should be matched to total fixture wattage. Standard drivers are ETL Listed, for remote use enclosure F Lutron 40W Remote - UL Listed, TRIAC/Forward Phase Dims to 1%, 120 VAC input note: for 120-277VAC input, Lutron 3-wire/Ecosystem dimming drivers available (up to 96W) X No power supply Juniper recommends Lutron DVCL-253P dimmers Contact Juniper for alternate dimming requirements Project Type Notes
THIN System Product Guide 16 TECHNICAL THIN Primaries Square Suspension 24in nominal - 27in overall [68.6cm] 36in nominal - 39in overall [99.1cm] 24 - max. 116in [292.1cm] 36 - max. 114in [294.6cm] Clear Lens 40 degree beam angle Frosted Lens 90 degree beam angle Ceiling Gripper 0.5in dia Remote Driver Canopy 5in dia x 0.5in ILLUMINATION 3000K and 90CRI standard 2700K and 4000K options available 24 2400 lm delivered / 32W 36 3680 lm delivered / 49.2W 78 lm/watt with clear acrylic lens 50,000 hrs LED life L80 POWER 24VDC output Class 2 constant voltage driver 120VAC input voltage Contact Juniper for alternate inputs Satin Brass, Black Oxide, Satin Nickel MATERIALS Solid brass, PMMA acrylic CERTIFICATIONS cul Damp Location Rated DIMMING TRIAC/Forward Phase/Leading-edge Juniper recommends Lutron DVCL- 253P dimmers See Power Supply section for details Contact Juniper for alternate requirements MOUNTING (4) 9.8ft (3m) 1/16 aircraft cable, field adjustable 16.4ft (5m) Clear-jacketed 22AWG side-by-side silver, field adjustable SYSTEM RUN Limited by driver wattage only GENERAL INFORMATION Designed by Peter Bristol & Juniper Assembled in USA
THIN System Product Guide 17 BUILD A SPECIFICATION THIN Primaries Square Suspension SERIES FINISH CONFIGURATION SEGMENTS COLOR TEMP JPR-THES - 0 - SQR - X X 2 - - - R 5 SAMPLE SKU: JPR-THES-01-SQR-3-30-F-R5G Satin Brass, 36 segments, 3000K, frosted lens, remote 96W Lutron power supply OR 3 REMOTE CANOPY POWER SUPPLY CODE DEFINITIONS REMOTE (POWER SUPPLY LOCATION) R Remote Power Supply - separately located near fixture in accessible location, connected via low-voltage Class 2 wiring supplied by electrician, use 5 5 x 0.5 round canopy CANOPY 01 Satin Brass 02 Black Oxide 03 Satin Nickel SEGMENTS 2 24 inch - 2400 lm delivered / 32W 3 36 inch - 3680 lm delivered / 49.2W Contact Juniper for custom segment lengths COLOR TEMPERATURE 27 2700K 30 3000K 40 4000K C Clear - 40 degree beam angle F Frosted - 90 degree beam angle 5 5 x 0.5 round paintable white canopy with 4 grippers (covers junction box) POWER SUPPLY - 24VDC CV OUTPUT A Standard 40W - TRIAC/Forward Phase dims to 5%, 120 VAC J Standard 60W - TRIAC/Forward Phase dims to 5%, 120 VAC note: for best dimming, Standard drivers should be matched to total fixture wattage. Standard drivers are ETL Listed, for remote use enclosure F Lutron 40W Remote - UL Listed, TRIAC/Forward Phase Dims to 1%, 120 VAC input H Lutron 96W Remote - UL Listed, 3-wire/Ecosystem dims to 0.1%, 120-277 VAC input note: for 120-277VAC input, Lutron 3-wire/Ecosystem dimming drivers available (up to 96W) X No power supply Juniper recommends Lutron DVCL-253P dimmers Contact Juniper for alternate dimming requirements Project Type Notes
THIN System Product Guide 18 TECHNICAL THIN Primaries Triangle Surface Mount 24in nominal - 27.3in [69.3cm] 36in nominal -40.3in overall [102.4cm] Standoff Options 7.1in [180mm] 3.5in [90mm] 1.9in [45mm] 1.2in [3.0cm] Clear Lens 40 degree beam angle Frosted Lens 90 degree beam angle ILLUMINATION 3000K and 90CRI standard 2700K and 4000K options available 24 1800 lm delivered / 24W 36 2760 lm delivered / 36.9W 78 lm/watt with clear acrylic lens 50,000 hrs LED life L80 POWER 24VDC output Class 2 constant voltage driver 120VAC input voltage Remote driver only Contact Juniper for alternate inputs Satin Brass, Black Oxide, Satin Nickel MATERIALS Solid brass, PMMA acrylic CERTIFICATIONS cul Damp Location Rated DIMMING TRIAC/Forward Phase/Leading-edge Juniper recommends Lutron DVCL- 253P dimmers See Power Supply section for details Contact Juniper for alternate requirements MOUNTING Wall brackets mount directly to drywall Optional junction box cover plate available 2 X 18AWG in-wall rated cable recommended for remote installation GENERAL INFORMATION Designed by Peter Bristol & Juniper Assembled in USA
THIN System Product Guide 19 BUILD A SPECIFICATION THIN Primaries Triangle Surface Mount SERIES FINISH CONFIGURATION SEGMENT STANDOFF COLOR TEMP JPR-THEW - 0 - TRI - X X - - - - X SAMPLE SKU: JPR-THEW-01-TRI-003-090-30-C-RXH Satin Brass, (3) 36 segments, 3000K, 90 mm standoffs, clear lens, remote 96W Lutron power supply 2 OR 3 LOCAL/REMOTE HARDWARE POWER SUPPLY CODE DEFINITIONS LOCAL/REMOTE (POWER SUPPLY LOCATION) R Remote Power Supply Location - separately located near fixture in accessible location, connected via low-voltage Class 2 wiring supplied by electrician P Plug-In Power Supply - fixture connects directly into wall via electrical cord and wall plug. 01 Satin Brass 02 Black Oxide 03 Satin Nickel SEGMENTS 2 24 inch - 1800 lm delivered / 24W 3 36 inch - 2760 lm delivered / 36.9W Contact Juniper for custom segment lengths STANDOFF LENGTH 045 45mm Standoffs - for undercabinet 090 90mm Standoffs - for general wall-wash and display 180 180mm Standoffs - for picture lighting COLOR TEMPERATURE 27 2700K 30 3000K 40 4000K C Clear - 40 degree beam angle F Frosted - 90 degree beam angle HARDWARE X no cover plate (for direct DC) POWER SUPPLY - 24VDC CV OUTPUT A Standard 40W - TRIAC/Forward Phase dims to 5%, 120 VAC J Standard 60W - TRIAC/Forward Phase dims to 5%, 120 VAC note: for best dimming, Standard drivers should be matched to total fixture wattage. Standard drivers are ETL Listed, for remote use enclosure F Lutron 40W Remote - UL Listed, TRIAC/Forward Phase Dims to 1%, 120 VAC input H Lutron 96W Remote - UL Listed, 3-wire/Ecosystem dims to 0.1%, 120-277 VAC input note: for 120-277VAC input, Lutron 3-wire/Ecosystem dimming drivers available (up to 96W) X No power supply Juniper recommends Lutron DVCL-253P dimmers Contact Juniper for alternate dimming requirements Project Type Notes
THIN System Product Guide 20 TECHNICAL THIN Primaries Square Surface Mount 24in nominal - 27in overall [68.6cm] 36in nominal - 39in overall [99.1cm] Standoff Options 7.1in [180mm] 3.5in [90mm] 1.9in [45mm] 1.2in [3.0cm] Clear Lens 40 degree beam angle Frosted Lens 90 degree beam angle ILLUMINATION 3000K and 90CRI standard 2700K and 4000K options available 24 2400 lm delivered / 32W 36 3680 lm delivered / 49.2W 78 lm/watt with clear acrylic lens 50,000 hrs LED life L80 POWER 24VDC output Class 2 constant voltage driver 120VAC input voltage Remote driver required Contact Juniper for alternate inputs Satin Brass, Black Oxide, Satin Nickel MATERIALS Solid brass, PMMA acrylic CERTIFICATIONS cul Damp Location Rated DIMMING TRIAC/Forward Phase/Leading-edge Juniper recommends Lutron DVCL- 253P dimmers See Power Supply section for details Contact Juniper for alternate requirements MOUNTING Wall brackets mount directly to drywall Optional junction box cover plate available 2 X 18AWG in-wall rated cable recommended for remote installation GENERAL INFORMATION Designed by Peter Bristol & Juniper Assembled in USA
THIN System Product Guide 21 BUILD A SPECIFICATION THIN Primaries Square Surface Mount SERIES FINISH CONFIGURATION SEGMENTS STANDOFF COLOR TEMP JPR-THEW - 0 - SQR - X X - - - - X SAMPLE SKU: JPR-THEW-01-SQR-2-045-30-F-RXH Satin Brass, (4) 24 segments, 3000K, 45mm standoffs, frosted lens, remote 96W Lutron power supply 2 OR 3 LOCAL/REMOTE HARDWARE POWER SUPPLY CODE DEFINITIONS LOCAL/REMOTE (POWER SUPPLY LOCATION) R Remote Power Supply Location - separately located near fixture in accessible location, connected via low-voltage Class 2 wiring supplied by electrician P Plug-In Power Supply - fixture connects directly into wall via electrical cord and wall plug. 01 Satin Brass 02 Black Oxide 03 Satin Nickel SEGMENTS 2 24 inch - 2400 lm delivered / 32W 3 36 inch - 3680 lm delivered / 49.2W Contact Juniper for custom segment lengths STANDOFF LENGTH 045 45mm Standoffs - for undercabinet 090 90mm Standoffs - for general wall-wash and display 180 180mm Standoffs - for picture lighting COLOR TEMPERATURE 27 2700K 30 3000K 40 4000K C Clear - 40 degree beam angle F Frosted - 90 degree beam angle HARDWARE X no cover plate (for direct DC or plug-in) POWER SUPPLY - 24VDC CV OUTPUT A Standard 40W - TRIAC/Forward Phase dims to 5%, 120 VAC J Standard 60W - TRIAC/Forward Phase dims to 5%, 120 VAC note: for best dimming, Standard drivers should be matched to total fixture wattage. Standard drivers are ETL Listed, for remote use enclosure F Lutron 40W Remote - UL Listed, TRIAC/Forward Phase Dims to 1%, 120 VAC input H Lutron 96W Remote - UL Listed, 3-wire/Ecosystem dims to 0.1%, 120-277 VAC input note: for 120-277VAC input, Lutron 3-wire/Ecosystem dimming drivers available (up to 96W) X No power supply Juniper recommends Lutron DVCL-253P dimmers Contact Juniper for alternate dimming requirements Project Type Notes
THIN System Product Guide 22 TECHNICAL THIN Multiples Dyad (Vertical) 3.5in [9cm] 0.5in [1.2cm] segment 0.7in [1.7cm] connector 24in and 36in Light Segments may be combined in the same fixture Standard max length per fixture is (3) 36 Light Segments 110.8in [281.5cm] For longer runs, please contact Juniper Clear Lens 40 degree beam angle Frosted Lens 90 degree beam angle Ceiling Gripper 0.5in dia Remote Driver Canopy 5in dia x 0.5in ILLUMINATION 3000K and 90CRI standard 2700K and 4000K options available 24 segment 1200 lm delivered / 16W 36 segment 1840 lm delivered / 24.6W 78 lm/watt with clear acrylic lens 50,000 hrs LED life L80 POWER 24VDC output Class 2 constant voltage driver 120VAC input voltage Contact Juniper for alternate inputs Satin Brass, Black Oxide, Satin Nickel MATERIALS Solid brass, PMMA acrylic CERTIFICATIONS cul Damp Location Rated DIMMING TRIAC/Forward Phase/Leading-edge Juniper recommends Lutron DVCL- 253P dimmers See Power Supply section for details Contact Juniper for alternate requirements MOUNTING 9.8ft (3m) 1/16 aircraft cable, field adjustable 16.4ft (5m) Clear-jacketed 22AWG side-by-side silver, field adjustable SYSTEM RUN Limited by driver wattage only GENERAL INFORMATION Designed by Peter Bristol & Juniper Assembled in USA
THIN System Product Guide 23 BUILD A SPECIFICATION THIN Multiples Dyad (Vertical) SERIES FINISH CONFIGURATION SEGMENTS COLOR TEMP JPR-THES - 0 - M D V - - - - R SAMPLE SKU: JPR-THES-01-MDV-333-30-F-LXA Satin Brass, (3) 36 segments, 3000K, frosted lens, local 40W Standard power supply (3 X 9.4W = 28.2W total) SAMPLE SKU: JPR-THES-02-MDV-023-27-C-R5F Black Oxide, (1) 24 segment, (1) 36 segment, 2700K, clear lens, remote 40W Lutron power supply with 5 canopy REMOTE CANOPY POWER SUPPLY CODE DEFINITIONS LOCAL/REMOTE (POWER SUPPLY LOCATION) R Remote Power Supply - separately located near fixture in accessible location, connected via low-voltage Class 2 wiring supplied by electrician, use 5 5 x 0.5 round canopy CANOPY 01 Satin Brass 02 Black Oxide 03 Satin Nickel SEGMENTS 0 no segment 2 24 inch segment - 1200 lm delivered / 16.0W 3 36 inch segment - 1840 lm delivered / 24.6W note: each digit represents a single segment, e.g. 323 is (1) 24 segment and (2) 36 segment Contact Juniper for custom segment lengths COLOR TEMPERATURE 27 2700K 30 3000K 40 4000K C Clear - 40 degree beam angle F Frosted - 90 degree beam angle 5 5 x 0.5 round canopy (covers junction box) X no canopy POWER SUPPLY - 24VDC CV OUTPUT A Standard 40W - TRIAC/Forward Phase Dims to 5%, 120 VAC B Standard 20W - TRIAC/Forward Phase Dims to 5%, 120 VAC note: for best dimming, Standard drivers should be matched to total fixture wattage. Standard drivers are ETL Listed, for remote use enclosure F Lutron 40W Remote - UL Listed, TRIAC/Forward Phase Dims to 1%, 120 VAC input note: for 120-277VAC input, Lutron 3-wire/Ecosystem Dimming drivers available (up to 96W) X No power supply Juniper recommends Lutron DVCL-253P dimmers Contact Juniper for alternate dimming requirements Project Type Notes
THIN System Product Guide 24 TECHNICAL THIN Multiples Dyad (Horizontal) 0.5in [1.2cm] segment 0.7in [1.7cm] connector 5.5in [9cm] 24in and 36in Light Segments may be combined in the same fixture Standard max length per fixture is (3) 36 Light Segments 110.8in [281.5cm] For longer runs, please contact Juniper Clear Lens 40 degree beam angle Frosted Lens 90 degree beam angle Ceiling Gripper 0.5in dia Remote Driver Canopy 5in dia x 0.5in ILLUMINATION 3000K and 90CRI standard 2700K and 4000K options available 24 segment 1200 lm delivered / 16W 36 segment 1840 lm delivered / 24.6W 78 lm/watt with clear acrylic lens 50,000 hrs LED life L80 POWER 24VDC output Class 2 constant voltage driver 120VAC input voltage Contact Juniper for alternate inputs Satin Brass, Black Oxide, Satin Nickel MATERIALS Solid brass, PMMA acrylic CERTIFICATIONS cul Damp Location Rated DIMMING TRIAC/Forward Phase/Leading-edge Juniper recommends Lutron DVCL- 253P dimmers See Power Supply section for details Contact Juniper for alternate requirements MOUNTING 9.8ft (3m) 1/16 aircraft cable, field adjustable 16.4ft (5m) Clear-jacketed 22AWG side-by-side silver, field adjustable SYSTEM RUN Limited by driver wattage only GENERAL INFORMATION Designed by Peter Bristol & Juniper Assembled in USA
THIN System Product Guide 25 BUILD A SPECIFICATION THIN Multiples Dyad (Horizontal) SERIES FINISH CONFIGURATION SEGMENTS COLOR TEMP JPR-THES - 0 - M D H - - - - R SAMPLE SKU: JPR-THES-01-MDH-333-30-F-LXA Satin Brass, (3) 36 segments, 3000K, frosted lens, local 40W Standard power supply (3 X 9.4W = 28.2W total) SAMPLE SKU: JPR-THES-02-MDH-023-27-C-R5F Black Oxide, (1) 36 segment, (1) 24 segment, 2700K, clear lens, remote 40W Lutron power supply with 5 canopy REMOTE CANOPY POWER SUPPLY CODE DEFINITIONS LOCAL/REMOTE (POWER SUPPLY LOCATION) R Remote Power Supply - separately located near fixture in accessible location, connected via low-voltage Class 2 wiring supplied by electrician, use 5 5 x 0.5 round canopy CANOPY 01 Satin Brass 02 Black Oxide 03 Satin Nickel SEGMENTS 0 no segment 2 24 inch segment - 1200 lm delivered / 16.0W 3 36 inch segment - 1840 lm delivered / 24.6W note: each digit represents a single segment, e.g. 323 is (1) 24 segment and (2) 36 segment Contact Juniper for custom segment lengths COLOR TEMPERATURE 27 2700K 30 3000K 40 4000K C Clear - 40 degree beam angle F Frosted - 90 degree beam angle 5 5 x 0.5 round canopy (covers junction box) X no canopy POWER SUPPLY - 24VDC CV OUTPUT A Standard 40W - TRIAC/Forward Phase Dims to 5%, 120 VAC B Standard 20W - TRIAC/Forward Phase Dims to 5%, 120 VAC note: for best dimming, Standard drivers should be matched to total fixture wattage. Standard drivers are ETL Listed, for remote use enclosure F Lutron 40W Remote - UL Listed, TRIAC/Forward Phase Dims to 1%, 120 VAC input note: for 120-277VAC input, Lutron 3-wire/Ecosystem Dimming drivers available (up to 96W) X No power supply Juniper recommends Lutron DVCL-253P dimmers Contact Juniper for alternate dimming requirements
TECHNICAL THIN Multiples Triad THIN System Product Guide 26 0.5in [1.2cm] segment 0.7in [1.7cm] connector 5.5in [9cm] 24in and 36in Light Segments may be combined in the same fixture. Standard max length per fixture is (2) 36 Light Segments 75in [190.5cm] For longer runs, please contact Juniper. Clear Lens 40 degree beam angle Frosted Lens 90 degree beam angle Ceiling Gripper 0.5in dia Remote Driver Canopy 5in dia x 0.5in ILLUMINATION 3000K and 90CRI standard 2700K and 4000K options available 24 segment 1800 lm delivered / 24W 36 segment 2760 lm delivered / 36.9W 78 lm/watt with clear acrylic lens 50,000 hrs LED life L80 POWER 24VDC output Class 2 constant voltage driver 120VAC input voltage Contact Juniper for alternate inputs Satin Brass, Black Oxide, Satin Nickel MATERIALS Solid brass, PMMA acrylic CERTIFICATIONS cul Damp Location Rated DIMMING TRIAC/Forward Phase/Leading-edge Juniper recommends Lutron DVCL- 253P dimmers See Power Supply section for details Contact Juniper for alternate requirements MOUNTING 9.8ft (3m) 1/16 aircraft cable, field adjustable 16.4ft (5m) Clear-jacketed 22AWG side-by-side silver, field adjustable SYSTEM RUN Limited by driver wattage only GENERAL INFORMATION Designed by Peter Bristol & Juniper Assembled in USA
THIN System Product Guide 27 BUILD A SPECIFICATION THIN Multiples Triad SERIES FINISH CONFIGURATION SEGMENTS COLOR TEMP JPR-THES - 0 - M T R - 0 - - - R SAMPLE SKU: JPR-THES-01-MTR-033-30-F-L5A Satin Brass, (2) 36 segments, 3000K, frosted lens, local in-canopy 40W Standard power supply (3 X 9.4W = 28.2W total) SAMPLE SKU: JPR-THES-02-MTR-003-27-C-RXF Black Oxide, (1) 36 segment, 2700K, clear lens, remote 40W Lutron power supply REMOTE CANOPY POWER SUPPLY CODE DEFINITIONS LOCAL/REMOTE (POWER SUPPLY LOCATION) R Remote Power Supply - separately located near fixture in accessible location, connected via low-voltage Class 2 wiring supplied by electrician, use 5 5 x 0.5 round canopy CANOPY 01 Satin Brass 02 Black Oxide 03 Satin Nickel SEGMENTS 0 no segment 2 24 inch segment - 1800 lm delivered / 24W 3 36 inch segment - 2760 lm delivered / 36.9W note: each digit represents a single segment, e.g. 023 is (1) 24 segment and (1) 36 segment Contact Juniper for custom segment lengths COLOR TEMPERATURE 27 2700K 30 3000K 40 4000K C Clear - 40 degree beam angle F Frosted - 90 degree beam angle 5 5 x 0.5 round canopy (covers junction box) X no canopy POWER SUPPLY - 24VDC CV OUTPUT A Standard 40W - TRIAC/Forward Phase dims to 5%, 120 VAC J Standard 60W - TRIAC/Forward Phase dims to 5%, 120 VAC note: for best dimming, Standard drivers should be matched to total fixture wattage. Standard drivers are ETL Listed, for remote use enclosure F Lutron 40W Remote - UL Listed, TRIAC/Forward Phase Dims to 1%, 120 VAC input H Lutron 96W Remote - UL Listed, 3-wire/Ecosystem dims to 0.1%, 120-277 VAC input note: for 120-277VAC input, Lutron 3-wire/Ecosystem dimming drivers available (up to 96W) X No power supply Juniper recommends Lutron DVCL-253P dimmers Contact Juniper for alternate dimming requirements Project Type Notes
TECHNICAL THIN Multiples Tetrad THIN System Product Guide 28 0.5in [1.2cm] segment 0.7in [1.7cm] connector 4.7in [12cm] 4.7in [12cm] Double configuration only available in 24in segments. Standard max length per fixture is (2) 36 Light Segments 75in [190.5cm] For longer runs, please contact Juniper. Clear Lens 40 degree beam angle Frosted Lens 90 degree beam angle Ceiling Gripper 0.5in dia Remote Driver Canopy 5in dia x 0.5in ILLUMINATION 3000K and 90CRI standard 2700K and 4000K options available 24 2400 lm delivered / 32W 36 3680 lm delivered / 49.2W 78 lm/watt with clear acrylic lens 50,000 hrs LED life L80 POWER 24VDC output Class 2 constant voltage driver 120VAC input voltage Contact Juniper for alternate inputs Satin Brass, Black Oxide, Satin Nickel MATERIALS Solid brass, PMMA acrylic CERTIFICATIONS cul Damp Location Rated DIMMING TRIAC/Forward Phase/Leading-edge Juniper recommends Lutron DVCL- 253P dimmers See Power Supply section for details Contact Juniper for alternate requirements MOUNTING 9.8ft (3m) 1/16 aircraft cable, field adjustable 16.4ft (5m) Clear-jacketed 22AWG side-by-side silver, field adjustable SYSTEM RUN Limited by driver wattage only GENERAL INFORMATION Designed by Peter Bristol & Juniper Assembled in USA
THIN System Product Guide 29 BUILD A SPECIFICATION THIN Multiples Tetrad SERIES FINISH CONFIGURATION SEGMENTS COLOR TEMP JPR-THES - 0 - M T E - 0 - - - R SAMPLE SKU: JPR-THES-01-MTE-003-30-F-L5A Satin Brass, (1) 36 segment, 3000K, frosted lens, local in-canopy 40W Standard power supply (3 X 9.4W = 28.2W total) REMOTE CANOPY POWER SUPPLY CODE DEFINITIONS LOCAL/REMOTE (POWER SUPPLY LOCATION) R Remote Power Supply - separately located near fixture in accessible location, connected via low-voltage Class 2 wiring supplied by electrician, use 5 5 x 0.5 round canopy CANOPY 01 Satin Brass 02 Black Oxide 03 Satin Nickel SEGMENTS 0 no segment 2 24 inch segment - 2400 lm delivered / 32W 3 36 inch segment - 3680 lm delivered / 49.2W (not available in double configuration) note: each digit represents a single segment, e.g. 022 is (2) 24 segments. Contact Juniper for custom segment lengths COLOR TEMPERATURE 27 2700K 30 3000K 40 4000K C Clear - 40 degree beam angle F Frosted - 90 degree beam angle 5 5 x 0.5 round canopy (covers junction box) X no canopy POWER SUPPLY - 24VDC CV OUTPUT A Standard 40W - TRIAC/Forward Phase dims to 5%, 120 VAC J Standard 60W - TRIAC/Forward Phase dims to 5%, 120 VAC note: for best dimming, Standard drivers should be matched to total fixture wattage. Standard drivers are ETL Listed, for remote use enclosure F Lutron 40W Remote - UL Listed, TRIAC/Forward Phase Dims to 1%, 120 VAC input H Lutron 96W Remote - UL Listed, 3-wire/Ecosystem dims to 0.1%, 120-277 VAC input note: for 120-277VAC input, Lutron 3-wire/Ecosystem dimming drivers available (up to 96W) X No power supply Juniper recommends Lutron DVCL-253P dimmers Contact Juniper for alternate dimming requirements Project Type Notes
TECHNICAL THIN Shared Task Lamp THIN System Product Guide 30 19in [48.5cm] 1.75in [4.4cm] cutout for fixture 12in max [30.5cm] 2in [5.1cm] cutout for toggle 1.2in [3.0cm] 21in [53.3cm] Light Segments may be combined in the same fixture Standard max length per fixture is (3) 24 Light Segments 75in [190.5cm] For longer runs, please contact Juniper Clear Lens 40 degree beam angle Frosted Lens 90 degree beam angle Plug-in Power Supply with on/off toggle switch (12W and 36W options available) ILLUMINATION 3000K and 90CRI standard 24 Segment 600 lm delivered / 8.0W 78 lm/watt with clear acrylic lens 50,000 hrs LED life L80 POWER 120VAC Input Voltage 12VDC Class 2 Constant Voltage Contact Juniper for alternate inputs Satin Brass, Black Oxide, Satin Nickel MATERIALS Solid brass, PMMA acrylic CERTIFICATIONS cul Damp Location Rated SYSTEM RUN Limited by driver wattage only GENERAL INFORMATION Designed by Peter Bristol & Juniper Assembled in USA
THIN System Product Guide 31 BUILD A SPECIFICATION THIN Shared Task Lamp SERIES FINISH SEGMENTS STANDOFFS COLOR TEMP JPR-THET - 0-0 0-4 8 5 - - SAMPLE SKU: JPR-THET-01-0002-090-30-C-RXC Satin Brass, (1) 24 segment, 90mm standoffs, 3000K, clear lens, remote 12W power supply POWER SUPPLY CODE DEFINITIONS C Clear - 40 degree beam angle F Frosted - 90 degree beam angle POWER SUPPLY G 12VDC 36W Plug-in Power Supply 01 Satin Brass 02 Black Oxide 03 Satin Nickel SEGMENTS 0 no segment 2 24 inch segment - 600 lm delivered / 8.0W X no power supply Juniper recommends Lutron DVCL-253P dimmers Contact Juniper for alternate dimming requirements note: each digit represents a single segment, e.g. 0022 is (2) 24 segments Contact Juniper for custom segment lengths STANDOFF LENGTH 485 485mm Standoffs COLOR TEMPERATURE 27 2700K 30 3000K 40 4000K Project Type Notes
FREQUENTLY ASKED QUESTIONS THIN System Product Guide 32 Are there more custom options that what is listed in this product guide? Our products have the ability to be highly customized to fit any setting or electrical need. If you have needs outside the product specifications or need to adjust the product for compatibility with your space, please contact us. Do you offer trade discounts? We are proud to support the industry by offering trade discounts to professionals. To join our trade program, email info@juniper-design.com and attach your tax ID or resale certificate. Once you are approved, you ll receive our standard trade discount with volume pricing breakdowns too. Do you have a showroom? Yes! Our showroom is located in Brooklyn, New York. We ask that you call 347-799-2915 to schedule an appointment in advance. One of our sales representatives will guide you through our product line and answer your questions. How do I get my order as quickly as possible? Since we receive machined parts from a third party and assemble all products in our Brooklyn design studio, lead times can vary depending on your order. Here are 3 ways to avoid further delays outside of our provided lead time: 1. Place your order quickly. To ensure that you will receive fixtures within your project s time constraints, we encourage placing your order as soon as possible. 2. Put a 50% deposit down, or pay in full. Our policy to begin prduction starts with a 50% deposit. Fixtures will only be shipped after the remaining balance of your order has been received. 3. Stay in touch with us. Should there be any changes to our production schedule or any early shipments, you will be contacted by Juniper as a standard practice. Make sure our emails don t get tucked away in a SPAM folder in case we re trying to reach you, or save our number in your contacts to know when we re calling! How do I contact Juniper? Our hours are 9AM - 5PM EST, Monday - Friday. During these hours, you can either email us (info@juniper-design.com) or call us directly (347-799-2915). Emails after hours are usually addressed within 24 hours.
CARE & UPKEEP INSTRUCTIONS THIN System Product Guide 33 Like other natural metals, brass will patina over time, with the natural yellow hues intensifying over time. Juniper protects its brass with a mild matte lacquer to delay coloration of the metal, and to protect it from exposure to humidity and natural oils. In order to remove dirt, dust and fingerprints; gently wipe the lamp with a damp cloth. Do not use any chemical cleaning solutions; especially those containing ammonia, as this will damage the surface finish of the brass. Do not drop or apply excessive force on any part or joint of the lamp. Do not attempt to disassemble or modify it in any way except for recycling. Do not use the lamp for any purpose other than its intended use. Use indoors only. Please contact us should the lamp not operate as described, and we will be happy to assist you.
11.8.2016 info@juniper-design.com +1 347 799-2915 68 33rd Street, Unit 11 Brooklyn, NY 11232