Metasys Integrator Cleaver-Brooks Application

Metasys Connectivity Technical Manual 69. Metasys Integrator Section Application Note Issue Date 0900 APPLICATION NOTE Metasys Integrator Cleaver-Brooks Application lntroduction Page Application Details * Component Requirements *8 Vendor Contact Information 9 Design Considerations *0 Cable Connections Cable Pinouts Connecting the Cable Metasys Integrator Setup * Point Mapping Tables Boiler Control Panel Points - ASCII Interface 6 Boiler Control Panel Points - CB-GPI *7 Enhancer Boiler Points - for ASCII Interface or CB-GPI 9 Enhancer General Points - ASCII Interface or CB-GPI 0 CB-780 Controller Points CB-78 Expanded Annunciator Points Metasys Network Setup Mapping to a CS Object * Custom Integration * *Indicates those sections where changes have occurred since the last printing. 000 Johnson Controls, Inc. Code No. LIT-690 www.johnsoncontrols.com

Metasys Integrator Metasys Integrator Cleaver-Brooks Application

lntroduction This document explains the Metasys Integrator Cleaver-Brooks application. Use this document with the Metasys Integrator technical bulletins in the Metasys Connectivity Technical Manual (FAN 69.) which provide information on installing and commissioning the Metasys Integrator unit. For information on Cleaver-Brooks boiler control panels, see Cleaver-Brooks documentation (obtainable from a Cleaver-Brooks representative). Note: If you are using a Universal Packaging Module (UPM), you must install the Metasys Integrator 00 Series in a two high enclosure (EN-EWC-0) rather than a one high enclosure (EN-EWC-0) as shown in the figures in this application note. Application Details ASCII Interface The Metasys Integrator unit allows Cleaver-Brooks equipment to become an integral part of the Metasys and Metasys Companion Networks. Once either a ASCII Interface or CB-General Purpose Interface (CB-GPI) and boiler control panels are connected to a Metasys or Companion Network via the Metasys Integrator unit, their data is available to the full complement of Metasys Building Automation System (BAS) features, including Change-of-State (COS) monitoring, alarm notification, trend, and totalization. The ASCII Interface allows information to be transmitted between boiler control panels and non-cleaver-brooks devices (such as the Metasys Integrator unit). A six slot CB-Link is required between the ASCII Interface and the boiler control panels. Optionally, you can connect a Enhancer to Slot 6. However, if you use a Enhancer, you must tie it into Slot 6, and you must then tie the ASCII Interface into Slot as shown in Figures and. Each Metasys Integrator vendor port can connect to one ASCII Interface. Each CB-Link can connect to five boiler control panels, or four boiler control panels and one Enhancer. Figure shows a Metasys Network with the Metasys Integrator unit connected to one ASCII Interface. Four boiler control panels connect to the ASCII Interface through Slots through on the CB-Link. A Enhancer connects to Slot 6 on the CB-Link. Figure shows a similar Cleaver-Brooks configuration integrated into a Metasys Companion Network. Metasys Integrator Metasys Integrator Cleaver-Brooks Application

ump Note: For a single boiler, the ASCII interface can connect directly to the boiler control panel without a CB-Link. See your Cleaver-Brooks representative. N LAN Standard Network Control Unit (NCU) RS-8 RS- ASCII Interface 6 CB-Link Metasys Integrator Unitary (UNT) Controller N Bus Boiler Control Panel () Boiler Control Panel () Boiler Control Panel () Boiler Control Panel () Enhancer Intcb Note: If you are using a UPM, you must install the Metasys Integrator 00 Series in a two high enclosure (EN-EWC-0) rather than a one high enclosure (EN-EWC-0) as shown in the figures in this application note. Figure : Cleaver-Brooks Boiler Control Panels and Metasys Integration ( ASCII Interface) Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Panel Unit Workstation RS-8 CB-Link RS- ASCII Interface 6 Metasys Integrator UNT N Bus Boiler Control Panel () Boiler Control Panel () Boiler Control Panel () Boiler Control Panel () Enhancer Cbcomp Note: If you are using a UPM, you must install the Metasys Integrator 00 Series in a two high enclosure (EN-EWC-0) rather than a one high enclosure (EN-EWC-0) as shown in the figures in this application note. Figure : Cleaver-Brooks Boiler Control Panel and Metasys Companion Integration ( ASCII Interface) CB-GPI You can also integrate Cleaver-Brooks equipment with the Metasys and Metasys Companion Networks through the CB-GPI. This interface resides on an RS-8 bus. The CB-Link communicates with up to five /CB-780 boiler controls and, optionally, a Enhancer. The RS-8 connects to a Johnson Controls RS- to RS-8 converter (MM-CVT0) which connects via an RS- cable to the Metasys Integrator panel. The Metasys Integrator unit can receive data from, and send data and commands to, Cleaver-Brooks equipment. Each Metasys Integrator vendor port can connect to one RS- to RS-8 converter which can connect by RS-8 bus to one CB-Link. Install the CB-GPI in Slot 6 of the CB-Link, unless a Enhancer is present. If a Enhancer is present, you must install it in Slot 6, and you must install the CB-GPI card in Slot. The number of boiler controllers that you may connect is then reduced to four. Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Figure shows a CB-Link Communication Interface with burner/boiler control equipment integrated into the Metasys Network. N LAN MM-CVT0 Converter RS-8 Standard NCU RS- CB-Link 6* Metasys Integrator Boiler Control Panel CB-780 UNT N Bus *Slot 6 on the CB-Link Communications Interface must contain a CB-GPI card unless a Enhancer option is present. intcbgpi Figure : Cleaver-Brooks Boiler Control and Metasys Integration (GPI Version) 6 Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Figure shows a CB-Link with burner/boiler control equipment integrated into the Metasys Companion Network. Panel Unit Workstation RS- MM-CVT0 Converter CB-Link 6* UNT Metasys Integrator RS-8 ** ** Boiler Control Panel N Bus *Slot 6 on the CB-Link Communications Interface must contain a CB-GPI card unless a Enhancer option is present. **End-of-Line (EOL) Resistor Required Enhancer Cbgpcomp Figure : Cleaver-Brooks CB-GPI and Metasys Companion Integration Metasys Integrator Metasys Integrator Cleaver-Brooks Application 7

Component Requirements ASCII Interface CB-GPI The following lists describe the components that are needed to integrate Cleaver-Brooks equipment through the ASCII Interface or through the CB-GPI:! Properly installed ASCII Interface, CB-Link, and boiler control panels! RS- cable (for connecting the ASCII Interface to the Metasys Integrator unit)! Metasys Integrator unit! N Bus (for connecting the Metasys Integrator unit to the Metasys or Companion Network)! Portable Personal Computer (PC) for downloading vendor communication tables (.VCT files) and network setup information into the Metasys Integrator unit, and for running diagnostics! Cable for connecting portable PC to the Metasys Integrator unit! The correct vendor communication table (.VCT file) to download into the Metasys Integrator unit (supplied on Metasys Integrator Tables and Models CD-ROM)! Properly installed CB-Link with a CB-GPI card installed in Slot 6 (unless you are using a Enhancer option) and Cleaver-Brooks equipment.(a Cleaver-Brooks representative is responsible for installing all Cleaver-Brooks equipment.)! If a Enhancer is present, you must install it in the sixth slot, and you must install the CB-GPI card in the fifth slot.! Johnson Controls RS- to RS-8 converter (MM-CVT0).! RS- cable (for connecting the MM-CVT0 to the Metasys Integrator unit).! RS-8 cable (for connecting the MM-CVT0 to the CB-GPI).! Metasys Integrator unit.! N Bus (for connecting the Metasys Integrator unit to the Metasys or Companion Network).! Portable PC for downloading vendor communication tables (.VCT files) and network setup information into the Metasys Integrator unit, and for running diagnostics.! Cable for connecting portable PC to the Metasys Integrator unit.! The correct vendor communication table (.VCT file) to download into Metasys Integrator (supplied on Metasys Integrator Tables and Models CD-ROM).! Enhancer Version 7. or higher. 8 Metasys Integrator Metasys Integrator Cleaver-Brooks Application

This document describes the RS- cable and the vendor communication tables. Cleaver-Brooks documentation describes their equipment. The remaining components are described in the Metasys Integrator technical bulletins. Metasys Release Requirements Metasys Companion Release Requirements Vendor Component Requirements Vendor Contact Information To integrate Cleaver-Brooks equipment into the Metasys Network, you will need:! Metasys Operator Workstation (OWS) software Release 6.0 or higher! Metasys Integrator software/firmware Release 7.0 or higher To integrate Cleaver-Brooks equipment into the Metasys Companion Network, you will need:! Metasys Companion Release.0 or higher! Metasys Integrator software/firmware Release 7.0 or higher Integration between the Metasys Integrator unit and Cleaver-Brooks has been tested with the ASCII Interface Version.0 Rev. C. Integration of Cleaver-Brooks products not discussed in this document will require additional software development and testing by Systems Products. For information on integrating other products, refer to the Custom Integration section in this document. Please contact the Service Group at your local Cleaver-Brooks office. Call Cleaver-Brooks at () 9-0600 for assistance in determining how to contact your local Cleaver-Brooks office. Metasys Integrator Metasys Integrator Cleaver-Brooks Application 9

Design Considerations When integrating Cleaver-Brooks equipment, keep the following considerations in mind: Make sure all Cleaver-Brooks equipment is set up and running properly before attempting to integrate with the Metasys or Companion Network. (The Cleaver-Brooks representative is responsible for operation of CB equipment.) RS- cable distance between the Metasys Integrator unit and the ASCII Interface or the Johnson Controls MM-CVT0 is a maximum of 0 feet. Cable distance between the CB-GPI and MM-CVT0 can be a maximum of 000 feet. The CB-780 Burner Control and the CB-78 Expanded Annunciator for a given burner must be commissioned to the same slot (they must have the same vendor address). When using the CB-GPI with a, configure the as Setback Capable = Yes. When using the CB-GPI with an Enhancer, follow these instructions:. Disconnect the Metasys Integrator unit.. Connect the 9-pin female connector to a PC Commissioning port using the RS-8 CVT-0 cable configured for a Metasys Integrator unit.. Configure a terminal emulator for 9600 baud, 8 bit, stop bit, no parity.. Enter this command in lower case to set the GPI to its default values: sz zap. Enter this command in lower case to set the reply timeout to 8 seconds: st 8 Make sure you select the Enter key after each command. 0 Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Cable Connections Cable Pinouts Use the following cable pinouts (Figure ) for the RS- connection between the Metasys Integrator unit and the ASCII Interface. (On standard NEMA Version, make connections to terminal block inside panel.) Vendor Port A or B of Integrator DB-9 Female ASCII Interface DB-9 Female Signal Pin Pin Signal TD RD GND RS- (0 ft maximum) RD TD GND intcb Figure : Cable Pinouts for ASCII Interface Use the following cable pinouts (Figure 6) for the RS- connection between the Metasys Integrator unit and the Johnson Controls MM-CVT0 RS- to RS-8 converter for use with the CB-GPI. Vendor Port A or B on Integrator DB-9 Female RS- Connector on MM-CVT0 DB- Male Signal Pin Pin Signal RD TD GND RTS 7 RS- (0 ft maximum) 7 RD TD GND RTS intcbgp Figure 6: Cable Pinouts to MM-CVT0 Converter for CB-GPI Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Use Figure 7 for the RS-8 bus wires connection between the RS-8 side of the Johnson Controls MM-CVT0 RS- to RS-8 converter and the CB-GPI. MM-CVT0 N+ N- REF RS-8 CB-GPI RS-8 + RS-8 - REF a b c intcb8 Figure 7: RS-8 Bus Wire Connection for CB-GPI Connecting the Cable Connect the female end of the RS- cable to either Vendor Port A or Vendor Port B on the Metasys Integrator unit. Connect the other end to the DB-9 on the ASCII Interface. (Standard NEMA Version has a terminal block instead of a connector.) Metasys Integrator ASCII Interface Vendor Port A or B RS- Cable DB-9 intcb Figure 8: Port to Port Connection Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Metasys Integrator Setup To set up the Metasys Integrator unit, use a portable PC connected to the Metasys Integrator Terminal Port. The Metasys Integrator unit setup involves: downloading the correct vendor communication table (.VCT file) setting up the port setting up the network addressing The following table provides information specific to the Cleaver-Brooks application. For detailed procedures, see the Metasys Integrator technical bulletins. If your system has a Enhancer option, you need to download the.vct files required for the Boiler points, Enhancer Boiler points, and the Enhancer general points. If you are not using a Enhancer, you need only the points. Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Table : Metasys Integrator Setup for Cleaver-Brooks Vendor Communication Table (.VCT FILE) Port Setup ASCII CB-GPI Interface Boiler Points CB_HAWK.VCT CB_HAWKG.VCT Enhancer Boiler Points Enhancer General Points CB-780 Burner Controller Points CB-78 Expanded Annunciator Points Network Setup CB_NHBP.VCT CB_NHGP.VCT Not Available Not Available Baud Rate 9600 9600 Word Length 8 8 Stop Bits Parity Even None Interface RS- RS-8 Vendor Address For Boiler Points: For Enhancer Boiler Points: For Enhancer General Points: CB-780 CB-78 to E to E 0 Not Available Not Available CB_NHBPG.VCT CB_NHGPG.VCT HW_RM78X.VCT HW_S780.VCT tgt, ss tgt, ss, blr tgt, ss tgt, ss tgt, ss Timeout Value With Enhancer Without Enhancer 000 ms -- -- -- 800 ms 6000 ms Poll Delay ms 0 ms Performance Guide Approximate Scan Time (For a single N address) Boiler Points Enhancer Boiler Points Enhancer General Points CB-780 Series Burner Controller Points CB-78 Expanded Annunciator Points seconds 0 seconds 0 seconds Not Available Not Available 9 seconds 6 seconds 6 seconds seconds seconds Where tgt = CB-GPI card address (default 0) and ss = CB-Link slot number (-6) Where tgt = CB-GPI card address (default 0), ss = CB-Link slot number (6) and blr = boiler number (-) Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Point Mapping Tables The following tables show the boiler control points. The points available for mapping depend on the type of equipment you are using. If you use only boiler control panels with an ASCII interface, use Table. If you also have a Enhancer, use the points shown in Tables,, and. The Enhancer points have been split into two groups: Enhancer Boiler Points (Table ) and Enhancer General Points (Table ). Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Boiler Control Panel Points - ASCII Interface To get the hardware reference for mapping points to a Control System (CS) object (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Gas Pressure point is. The hardware reference for the Pilot Valve point is 8. The points (internal parameters) cannot be mapped to standard objects. To monitor these points, map them to CS object AD attributes (which can then be mapped to standard objects). Table : Boiler Control Panel Points - ASCII Interface NPT NPA Unit Description 6 6 7 8 9 0 6 psi psi psi % Operating Pressure (Steam Boiler) Operating Temperature (Hot Water Boiler) Gas Pressure Oil Pressure Oil Temperature Fire Rate Fire Rate Mode 0-auto, -manual Atomizing Air Proving Switch 0-off, -on Assured Low-Fire Cutoff 0-off, -on Demand Terminal 0-off, -on Recycle Limits 0-off, -on Pre-Ignition Interlock 0-off, -on Lock Out Interlock 0-off, -on Pilot Valve 0-off, -on Gas Main Valve 0-off, -on Oil Main Valve 0-off, -on Operating Setpoint (psi) (0-70) Operating Boiler Off Control Setpoint (psi) (0-70) Operating Boiler On Control Setpoint (psi) (0-70) Set Back Setpoint (psi) (0-70) Set Back Boiler Off Control Setpoint (psi) (0-70) Set Back Boiler On Control Setpoint (psi) (0-70) BO Set Back Mode 0-no, -yes 6 7 8 9 0 # # # hour # hour % # # Network Point Type Network Point Address Fuel Selection (None, Gas, LtOil, HyOil, ChangOvr) Boiler Medium (None, Steam, Hot Water) Burner Status Burner Status Extended Total Cycles Total Runtime History - Burner Status History - Burner Status Extended History - Fault Code History - Fault Cycle History - Fault Hours History - Fire Rate History - Fuel Selection History - Sequence Timer 6 Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Boiler Control Panel Points - CB-GPI To get the hardware reference for mapping points to a CS object (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Gas Pressure point is. Table : Boiler Control Panel Points - CB-GPI NPT NPA Unit Description 6 7 8 6 7 8 9 0 6 psi psi psi % hp Volt Operating Pressure (Steam Boiler Only) Operating Temperature (Hot Water Boiler Only) Gas Pressure (Gas Fuel Only) Oil Pressure (Oil Fuel Only) Oil Temperature (Oil Fuel Only) Fire Rate Boiler Size Flame Signal Gas Fuel Select 0-Off, -On Light Oil Fuel Select 0-Off, -On Heavy Oil Fuel Select 0-Off, -On Pre-Ignition Interlock 0-Off, -On Recycle Limits 0-Off, -On Lock Our Interlock 0-Off, -On Pilot Valve 0-Off, -On Gas Main Valve 0-Off, -On Oil Main Valve 0-Off, -On Atomizing Air Proving Switch 0-Off, -On Burner Switch (Demand) 0-Off, -On Assured Low Fire Cutoff 0-Off, -On Fire Rate Mode 0-Auto, -Manual Keyboard Mode 0-Program, -Operate Operating Setpoint (psi) (0-70) Operating Boiler Off Control Setpoint (psi) (0-70) Operating Boiler On Control Setpoint (psi) (0-70) Set Back Setpoint (psi) (0-70) Set Back Boiler Off Control Setpoint (psi) (0-70) Set Back Boiler On Control Setpoint (psi) (0-70) BO Set Back Mode 0-No, -Yes 6 7 8 9 Boiler Medium (None, Steam, Hot Water) Boiler Type (None, Firetube, Watertube) Fuel Selection Fuel Series Flame Amplifier Part No. 8 - (, 0, 6) Rate Linearization Control Source (Auto, Manual, Remote) Set Back Capable (None, No, Yes) Program Identifier Network Point Type Network Point Address For more information, see Cleaver-Brooks documentation. Only the points that are applicable to the boiler configuration will be reliable. Continued on next page... Metasys Integrator Metasys Integrator Cleaver-Brooks Application 7

NPT (Cont.) NPA Unit Description 0 6 7 8 9 0 6 7 8 # % % sec sec sec # hour # hour % sec Response Factor Low Fire Rate Max Fire Rate Prepurge Extend Post purge Extend Sequence Timer Burner Status Burner Status Extended Total Cycles Total Runtime History - Burner Status History - Burner Status Extended History - Fault Code History - Fault Cycle History - Fault Hours History - Fault Message History - Fire Rate History - Fuel Selection History - Sequence Timer Network Point Type Network Point Address For more information, see Cleaver-Brooks documentation. 8 Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Enhancer Boiler Points - for ASCII Interface or CB-GPI To get the hardware reference for mapping points to a CS object (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Total Fuel Used point is 9. Table : Enhancer Boiler Points - ASCII Interface or CB-GPI NPT NPA Unit Description 6 7 8 9 0 6 7 % % % % MBTU MBTU $ Gal (or Therms) % % See Note. Stack Temperature Instant Efficiency Average Efficiency ( hour) Average Efficiency (8 hour) Average Efficiency ( hour) Total BTU Input Total BTU Output Average Cost of Output Total Fuel Used Oxygen Carbon Monoxide Opacity Fuel Flow Water/Steam Flow Nitrogen Oxides Auxiliary Input Auxiliary Input Network Point Type Network Point Address User-defined units. For more information, see Cleaver-Brooks documentation. The following notes refer to optional features for Enhancers. These points are valid only with a Enhancer with the feature listed. Efficiency Auxiliary Input Metasys Integrator Metasys Integrator Cleaver-Brooks Application 9

Enhancer General Points ASCII Interface or CB-GPI To get the hardware reference for mapping points to a CS object (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Ambient Temperature point is. Table : Enhancer General Points - ASCII Interface or CB-GPI NPT NPA Unit Description psi (or psi) Header Pressure (Steam Boiler) Header Temperature (Hot Water Boiler) Ambient Temperature Outdoor Temperature Outdoor Reset Actual Setpoint (or psi) (or psi) System Setpoint (psi) (0-70) (or psi) System On Point (psi) (0-70) (or psi) System Off Point (psi) (0-70) (or psi) Setback Setpoint (psi) (0-70) (or psi) Setback On Point (psi) (0-70) 6 (or psi) Setback Off Point (psi) (0-70) 7 8 9 0 # # # # # $ Lead Boiler # (0-) st Lag Boiler # (0-) nd Lag Boiler # (0-) rd Lag Boiler # (0-) th Lag Boiler # (0-) Cost of Gas (0.0-9.99) $ Cost of Light Oil (0.0-9.99) $ Cost of Heavy Oil (0.0-9.99) Set Back Status 0-No, -Yes BO Reset Fuel Totals 0-Reset -Reset ADF ADF ADF ADF ADF % sec % sec Lag On Trigger Point Lag On Time Delay Lag Off Trigger Point Lag Off Time Delay Reset Ratio Network Point Type Network Point Address The following three notes refer to optional features for Enhancers. These points are only valid with a Enhancer with the feature described. Lead Lag Efficiency Outdoor Reset 0 Metasys Integrator Metasys Integrator Cleaver-Brooks Application

CB-780 Controller Points To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for Test/Run Switch is. points (internal parameters) cannot be mapped to standard objects. To monitor these points, map them to CS object AD attributes (which can then be mapped to standard objects). Table 6: CB-780 Controller Points NPT NPA Unit Description Volt Flame Signal 6 7 8 9 0 6 7 8 9 0 Sec Sec Sec Test/Run Switch 0-run, -test Operating Control T6 0-off, -on Interlock T7 0-off, -on Pilot Valve T8 0-off, -on Main Valve T9 0-off, -on Ignition T0 0-off, -on Pilot Valve Hold T6 0-off, -on Manual Open Switch T7 0-off, -on Low Fire Switch T8 0-off, -on High Fire Switch T9 0-off, -on Pre-Ignition Switch T0 0-off, -on Valve /Start T 0-off, -on Sequence Status Sequence Extension Sequence Timer Remote Command Burner Availability Amplifier Type Flame Response 0-0.8 sec, -.0 sec Purge Time History -- Fault Code History -- Fault Message History -- Sequence Status History -- Sequence Extension History -- Sequence Timer Network Point Type Network Point Address For more information, see Cleaver-Brooks documentation. Metasys Integrator Metasys Integrator Cleaver-Brooks Application

CB-78 Expanded Annunciator Points To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for Valve Closure is. points (internal parameters) cannot be mapped to standard objects. To monitor these points, map them to CS object AD attributes (which can then be mapped to standard objects). Table 7: CB-78 Expanded Annunciator Points NPT NPA Unit Description 6 7 8 9 0 6 7 8 9 0 Valve Closure T 0-off, -on Burner Switch T 0-off, -on Operating Control T6 0-off, -on Auxiliary Limit T7 0-off, -on Auxiliary Limit T8 0-off, -on Low Water Cut Out T9 0-off, -on High Limit T0 0-off, -on Auxiliary Limit T 0-off, -on Oil Select T 0-off, -on Hi Oil Pressure T 0-off, -on Lo Oil Pressure T 0-off, -on Hi Oil Temperature T 0-off, -on Lo Oil Temperature T6 0-off, -on Atomizing Switch T9 0-off, -on Gas Select T7 0-off, -on Hi Gas Pressure T8 0-off, -on Lo Gas Pressure T9 0-off, -on Airflow Switch T0 0-off, -on Auxiliary Interlock T 0-off, -on Auxiliary Interlock T 0-off, -on Current Status Fault First Out Fault Valve Closure (unknown, off, on) Network Point Type Network Point Address For more information, see Cleaver-Brooks documentation. Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Metasys Network Setup Metasys Network Setup is described in the Metasys Integrator technical bulletins. This section contains details specific to Cleaver-Brooks applications. Mapping to a CS Object Table 8 lists the software model files and the recommended Display and Network Terminal (NT) Command Attributes. Whether all the models shown in the table are needed depends on the equipment used. For example, if the system has only boiler control panels (and no Enhancer), only the model file for boiler control points is needed. If the system has a Enhancer and an ASCII interface, all the three ASCII model files are used. The Enhancer points are split into two groups: Enhancer boiler points and Enhancer general points The point mapping tables show how the points are categorized. Table 8: Software Model and CS Object Details Application Boiler Control Points - ASCII Enhancer Boiler Points - ASCII or GPI Enhancer General Points - ASCII or CB-GPI Boiler Control Points - GPI Software Model (on Tables and Models CD-ROM) CB_HAWK.DDL Display Attribute (recommended) (steam) or (hot water) CB_NHBP.DDL CB_NHGP.DDL CB_HAWKG.DDL (steam) or (hot water) (steam) or (hot water) CB-780 HW_RM78X.DDL Flame Signal CB-78 HW_S780.DDL Burner Switch NT Command Attribute (recommended) BO BO BO Whether you use the or point depends on whether your system has a steam boiler or a hot water boiler. For the NT Command attribute, use the same attribute as the Display attribute. However, since the CB-780 and CB-78 points are not commandable, you will not be able to command the attribute. (This must be defined, because the NT Command attribute cannot be null.) Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Custom Integration For information on integrating products which are not discussed in this document, first refer to the Metasys Compatible Global Catalog, an online list of released Connectivity products. If this list does not provide the information you require, consider using the System Integration Project Data Sheet to request a custom contract from the System Integration Team. Both the Metasys Compatible Global Catalog and the System Integration Project Data Sheet are accessible from The Advisor by performing the following steps:. Click on the Systems Products button located on the left side of The Advisor home page.. Click on the Product Literature link.. Click on the Manuals-FANS link.. Click on the 69.0 Metasys Connectivity Sales Resource Manual link.. Find the System Integration Project Data Sheet link in the table of contents. Click on this link to view an online copy of the System Integration Project Data Sheet or click on the Metasys Compatible Global Catalog link below the data sheet to view a list of released Connectivity products. The System Integration Project Data Sheet (LIT-6900) is found in the Metasys Connectivity Sales Resource Manual (FAN 69). If you need further assistance, contact Johnson Controls Field Support Center. Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Notes 6 Metasys Integrator Metasys Integrator Cleaver-Brooks Application

Notes Metasys Integrator Metasys Integrator Cleaver-Brooks Application 7

Notes www.johnsoncontrols.com Controls Group FAN 69. 07 E. Michigan Street Metasys Connectivity Technical Manual P.O. Box Metasys Integrator Release 9.0 Milwaukee, WI 0 Printed in U.S.A. 8 Metasys Integrator Metasys Integrator Cleaver-Brooks Application