Model 08/0 Code ranslator Installation and peration Instructions he 08/0 Code ranslator is an interface unit used with American Dynamics Switching Systems. he unit translates codes which then enable the use of American Dynamics equipment with that of Sensormatic Speed Domes and Mini Domes.
his software/firmware is confidential to and is copyrighted by SENSRMAIC ELECRNICS CRPRAIN. It is not to be copied or disclosed in any manner without the express written consent of SENSRMAIC. he software is furnished to the purchaser under a license for use on a single system. NE: Information furnished by SENSRMAIC is believed to be accurate and reliable. However, no responsibility is assumed by SENSRMAIC for its use; nor for any infringements of other rights of third parties which may result from its use. No license is granted by implications or otherwise under any patent or patent rights of SENSRMAIC. Copyright 997 by SENSRMAIC. All rights reserved.
AMERICAN DYNAMICS he installation of this product should be made by qualified service personnel and should conform to all local codes. CAUIN RISK F ELECRIC SHCK D N PEN! CAUIN: REDUCE HE RISK F ELECRIC SHCK, he lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. D N REMVE CVERS (R BACK). N USER-SERVICEABLE PARS INSIDE. REFER SERVICING QUALIFIED SERVICE PERSNNEL! he exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING o reduce the risk of fire or shock hazard, do not expose this product to rain or moisture. his equipment has been tested and found to comply with Part 5 of the FCC Rules. peration is subject to the following two conditions:. his device may not cause harmful interference, and. his device must accept any interference received, including interference that may cause undesired operation. UNPACKING AND INSPECIN Unpack carefully. his is an electronic product and should be handled as such. Compare the items received with the packing list with your order. Be sure to save:. he shipping cartons and insert pieces. hey are the ) safest material in which to make future shipments of the product.. he IMPRAN SAFEGUARDS sheet.. hese Installation and perating Instructions. MAINENANCE User maintenance of this unit is limited to external cleaning and inspection. For specific recommendations refer to the IMPRAN SAFEGUARDS sheet packaged with this product. INSALLAIN AND SERVICE If you require information during installation of this product or if service seems necessary, contact the Sensormatic Repair and Service Department at (800) -5. You must obtain a Return Authorization Number and shipping instructions before returning any product for service. Do not attempt to service this product yourself. pening or removing covers may expose you to dangerous voltages or other hazards. Refer all servicing to qualified personnel. QA0D
able of Contents Product Description... Installation... Setup... Connections... peration... ypical Connections...Appendix
DESCRIPIN S S GRUP DAA LINE IN R R R R R R R R B W S N NC C PWER ALARM CDE R R R R R R R R R R R R R R R R R R R R R R R R C M INPU UPU 0V 60Hz U S S Figure -08/0 Code ranslator Rear Panel PRDUC DESCRIPIN he 08/0 Code ranslator is used as an interface to American Dynamics switching systems. he 08/0 allows for the retrofit or new installation of American Dynamics switchers using RS- transmission systems and non-ad receivers. his unit only interfaces with Sensormatic Speed Domes and Mini Domes. When using the Control Code interface this unit can control up to 6 domes with 650 switchers, and domes with 50 switchers. Multiple 08/0 units can be used to control additional domes with the Control Code interface. When using the Data Line interface the 08/0 can control up to 5 domes with 995 systems, and 0 domes with 050 systems. FEAURES INSALLAIN he universal cabinet of the 08/0 Code ranslator may be surface or rack mounted in any convenient location with adequate ventilation. Rack Mounting As shipped, with the mounting ears flush with the front panel, the 08/0 Code ranslator can be mounted into the front of a standard 9-inch rack. he ears of the 08/0 Code ranslator can be removed and reinstalled such that they are flush with the rear panel. his allows the 08/0 to be mounted to the rear of a rack that is equipped with mounting channels. For proper ventilation allow at least three feet (m) from the rear of the racks to any wall, and one EIA rack height,.75 inches (.5cm), between units in a rack. Universal Mount Cabinet LED Power /Alarm/Code Indicator DIP Switch Selection for Camera Group DIP Switch Configuration for Baud Rate Screw erminal Wire Connector DIP Switch Dome ype Selection Wall Mounting he Code ranslator can be mounted to the wall by reinstalling the ears perpendicular to the side of the unit. he unit can be installed with either the bottom or the top cover facing the wall and the front or the rear panel facing upwards. RACK CHANNEL WALL IF YU ENCUNER ANY PRBLEMS PERAING HIS UNI, R NEED ECHNICAL ASSISANCE, CALL UR SERVICE CENER A: within the United States -800--5 outside the United States (9) 6-760 P CVER FRN R REAR PANEL MUNING EARS INSALLED FLUSH WIH HE FRN R REAR PANEL FRN R REAR PANEL P R BM CVER MUNING EARS INSALLED PERPENDICULAR HE SIDES RACK MUNED Figure - Mounting ptions WALL MUNED
SEUP SEUP Internal Setups Camera Block Assignments Four 8-position DIP switches ( S, S, S, and S) are located on the rear panel of the unit, as shown in Figure, page. he settings of these switches determine the cameras associated with the connectors in each of four selective groups. he active positions for each DIP switch are labeled A, B, C, and D (see Figure ). able shows the switch settings as they correspond to the camera assignments for Sensormatic Speed Domes and Mini Domes. able - S, S, S, and S Setup Speed Dome Video Input Switch Positions (0=FF, =N) Camera #s A B C D -99 0 0 0 0 00-98 0 0 0 99-97 0 0 0 98-96 0 0 97-95 0 0 0 96-59 0 0 595-69 0 0 69-79 0 79-89 0 0 0 89-990 0 0 99-0 0 0 Mini Dome Video Input Switch Positions (0=FF, =N) Camera #s A B C D -79 0 0 0 0 80-58 0 0 0 59-7 0 0 0 8-6 0 0 7-95 0 0 0 96-7 0 0 75-55 0 0 55-6 0 6-7 0 0 0 7-790 0 0 79-869 0 0 870-98 0 99-0 0 0 S5 S6 FRN off Figure - Location of DIP Switches on PCB 8 - CAUIN - he following internal adjustments, requiring removal of the top cover, will expose hazardous-voltage components and allow access to dangerous electric shock potentials. hese internal adjustments should be made only by qualified service personnel. wo 8-position DIP switches (S5 and S6) are located on the main PCB inside the unit (see Figure ). Each DIP switch has eight switch positions, numbered through 8. he active position numbers are used for the following setup functions. Baud Rate Selection he S5 DIP switch settings configure the input and output baud rates for the two RS- CM terminals and for the RS- terminal pins of the Sensormatic interface connectors. able shows the S5 switch position settings for baud rate. able - S5 Setup Switch Position #s CM U CM IN RS BAUD RAE 5 6 00 FF FF FF FF FF FF 00 N FF N FF N FF 800 FF N FF N FF N 9600 N N N N N N Note: Sensormatic Domes work at 800 Baud only. Alarm Contacts and Dome ype Setup he S6 DIP switch is used for selecting the number of alarm switch contacts that can be configured for each dome. his switch also selects the dome type for each of the four groups of connectors. nly one dome type, Speed Dome or Mini Dome, may be selected for each connector group. able shows the S6 switch position settings for these selections. able - S6 Setup Number of Alarm Contacts per Dome Switch Position # FF N FF N FF FF N N Switch Position # Group Speed Domes Mini Domes 5 FF N 6 FF N 7 FF N 8 FF N
CNNECINS CNNECINS Sensormatic Interface Connectors Eight -pin connectors on the rear of the 08/0 Code ranslator panel are used for transmitting and receiving codes with Sensormatic domes and J-boxes. he transmit () and receive (R) signal positions are labeled on each connector. Each connector is supplied with a mating screw terminal connector (see Figure ). HLD DWN SCREWS Data Line Connectors wo DAA LINE BNC connectors are provided on the rear panel, labeled IN and U. he IN is used to receive control codes from the 995 or the 996 CPU of the 050 systems. he U is a loop through connection. his line must be terminated in 75 ohms. Use a good grade RG-59U video cable for all connections. Note: When 995 or 050 systems with existing B/W/S Control Code interfaces are used, they can be connected to the 08/0 Control Code Connector, as shown in Figure 5 above. RS- Connectors R R R R INSER CNNECR HIS DIRECIN wo RS- connectors on the rear panel, labeled INPU and UPU, are provided for alarm interface connections. he output port is for connection to the switcher/control system alarm input ports or for cascading to another 08/0 unit's input port or a 096 Alarm Interface unit. he baud rate is set for these ports as shown in able, page. Figure - ypical Mating Screw Connector Control Code Connector he upper right connector on the rear of the 08/0 Code ranslator is a -pin connector. his is used to receive Control Code signals from 650 or 50 switcher units (B, W and S lines) and to provide access to an internal Form C alarm relay. When the 08/0 receives an alarm from any controlled Sensormatic receiver, the internal alarm relay closes. his relay can be used for turning accessories (VCR, etc.) on or off via its Normally pen (N) or Normally Closed (NC) terminals. he mating screw terminal connector is shown below (see Figure 5). B W S HLD DWN SCREWS he RS- connectors are 8-pin modular type RJ-5 connectors. he pinout definitions for the two connectors are shown in able. able - RS- Connectors Pin Definitions Pin INPU UPU Shield Shield RCD RCD 5 XMI XMI 7 GND GND Remaining Pins - No Connection he 08/0 can be connected to switching systems using a modular cable, JJ0007, when distances between the units are no further than 7 feet apart. For connection to switchers where the distances exceed 7 feet, a modular cable with a wall-mount 8-pin erminal Block, Figure 6, is provided for plug-in to the rear panel connectors. he pin definitions for this block are the same as in able. See Appendix for typical connections. B = BLACK W = WHIE S = SHIELD N = NRMALLY PEN NC = NRMALLY CLSED C = CMMN N NC C INSER CNNECR HIS DIRECIN Figure 5 - Control Code Mating Connector PIN PIN PIN 5 PIN 6 Connections on the above -pin connectors are easily made by inserting signal and ground wires into the slots of the mating connectors and tightening the hold down screws. When all wires have been connected, insert the -pin mating connectors into the rear panel. PIN PIN 7 PIN PIN 8 Figure 6-8-pin erminal Block
PERAIN PERAIN Power Sources D N CNNEC HE EQUIPMEN A PWER SURCE UNIL READY "PWER UP''. Make all connections to the 08/0 code input and relay connections and set the DIP switches prior to power up. he 08/0 Code ranslator does not contain an n/ff Switch. he socket outlet shall be located near the equipment and shall be readily accessible. he 0 V units are supplied with a pendant -wire cord and plug for mating to the primary source outlet. he 0 V units are supplied with a Euro style IEC 0 type inlet. A suitable detachable cord should be connected between the IEC 0 inlet and the power source. he cord should be connected between the IEC 0 inlet and the power source. he cord should conform to all national and local use code requirements. A green PWER LED indicator located on the rear panel illuminates when power is applied. Code ranslators are available in two models, depending on the power source to be used: AD08/0 0VAC, 50/60 Hz ADS08/0X 0VAC, 50/60 Hz he 08/0 unit has fuse power protection. he fuse sizes for replacement are: 0V - 50V, SB, 5 ma, 5 x 0mm 0V - 50V,, 5 ma, 5 x 0mm perating Indicators When the unit is receiving valid code, the green CDE LED, on the rear panel, is illuminated. he LED stays lit for 5 seconds after code is removed. If this LED does not light, a problem in the unit or its interconnection may be indicated. Controlling Sensormatic Receiver Features he 08/0 supports the transmitted codes for all Sensormatic Speed Domes and Mini Domes. his includes full Pan, ilt and Lens control, 6 presets per receiver and special Console to Dome commands per Speed Dome. he special Console to Dome commands are: Reset Iris, Increase V-Phase Delay, Decrease V-Phase delay and Reset Dome. All pattern programming features of the Sensormatic domes are also provided. All functions are controlled via the AD keyboard, using the keys indicated in able 5, page 5. he commands shown are all applicable to Speed Domes. Several of the commands are applicable for Mini Dome functions. he 08/0 also supports alarm contacts. he American Dynamics Start Alarm and Stop Alarm commands are transmitted via the RS output port. he alarm contact number is the American Dynamics real camera address. When an alarm is received, an internal relay closes and the green alarm LED illuminates. he alarm reading is an asynchronous operation, working on a first-in first-out basis. he alarm contacts have one of two possible normal positions: open or closed. he 08/0 is initialized with a default setting of all switch contacts normally closed. If any dome is configured to a non-default setting, switch normally open, then refer to able 5 for the AD keyboard commands to set the appropriate switch state in the 08/0. Note that these commands must be used for each dome that is not set to normally closed, or was changed after the 08/0 was powered up. If an alarm input is activated, the green ALARM LED illuminates, and the alarm relay closes. he ALARM LED remains illuminated and the alarm relay remains closed for 0 seconds after the alarm input is removed.
PERAIN able 5 - Sensormatic Dome Commands Dome Function Set Preset - 6 Call Preset - 6 Reset Iris Enter V-Phase Adjust Mode Exit V-Phase Adjust Mode Reset Dome Set Switch Normal Closed Set Switch Normal pen Set Switch Normal Closed Set Switch Normal pen Set Switch Normal Closed Set Switch Normal pen Set Switch Normal Closed Set Switch Normal pen Set Auxiliary FF Set Auxiliary N Flip (Camera position 80 ) AD Keyboard Command - 6 Set Shot - 6 Call Shot 69 Set Shot 67 Set Shot followed by multiple Iris pen or Iris Close 68 Set Shot 66 Call Shot followed by 66 Set Shot 5 Set Shot 5 Set Shot 5 Set Shot 5 Set Shot 6 Set Shot 6 Set Shot 6 Set Shot 6 Set Shot 70 Call Shot 7 Call Shot 0 Call Shot Pattern Programming Define Pattern # Define Pattern # Define Pattern # End Pattern Definition Accept (save) New Pattern Clear Pattern # Clear Pattern # Clear Pattern # Goto Pattern # Goto Pattern # Goto Pattern # Goto Pattern # Run Pattern # Run Pattern # Run Pattern # Run Pattern # Auto Repeat Pattern # Auto Repeat Pattern # Auto Repeat Pattern # Auto Repeat Pattern # 7 Set Shot 8 Set Shot 9 Set Shot Set Shot Set Shot Set Shot Set Shot Set Shot 7 Call Shot 8 Call Shot 9 Call Shot 0 Call Shot Call Shot Call Shot Call Shot Call Shot 5 Call Shot 6 Call Shot 7 Call Shot 8 Call Shot 5
APPENDIX
YPICAL SYSEM CNNECINS 995 08 GRUP DAA LINE IN R R R R R R R R B W S N NC C PWER ALARM CDE R R R R R R R R R R R R R R R R R R R R R R R R C M INPU UPU 0V 60Hz U 08 JJ0007 BRWN (GRD) HP007 ERMINAL BX 8 NE: MAX. DISANCE BEWEEN ERMINAL BX AND 995 CNNECR IS 000' (0m), USING CMPUER GRADE CABLE 8 AWG 7 GREEN (XMI) CAX CABLE 995 RS Ports -0: Pin - XMI Pin - RCD Pin 5 - GND 5 6 7 8 9 6 5 RED (RCD) RS LAN IN U LAN IN U PR PR PR 0 PR 9 PR 8 PR 7 PR 6 PR 5 PR PR 995 A
YPICAL SYSEM CNNECINS 996 08 GRUP DAA LINE IN R R R R R R R R B W S N NC C PWER ALARM CDE R R R R R R R R R R R R R R R R R R R R R R R R C M INPU UPU 0V 60Hz U 08 JJ0007 NES:. MAX. DISANCE BEWEEN ERMINAL BXES IS 000' (0m) USING CMPUER GRADE CABLE 8 AWG. IF LESS HAN 7 FEE, JJ0007 CABLE MAY BE RUN DIRECLY WIHU ERMINAL BXES BRWN (GRD) 8 HP007 ERMINAL BX 7 GREEN (XMI) RED (RCD) GREEN (XMI) 5 7 6 6 5 RED (RCD) HP007 ERMINAL BX 8 BRWN (GRD) CAX CABLE JJ0007 DAA LINE PRS PRG MN 0V 60Hz 5 6 7 8 9 0 996 A
YPICAL SYSEM CNNECINS 650 08 GRUP DAA LINE R R R R R R R R B W S N NC C IN PWER ALARM CDE R R R R R R R R R R R R R R R R R R R R R R R R C M INPU UPU 0V 60Hz U HP007 ERMINAL BX JJ0007 08 BRWN (GRD) 8 RED (RCD) NES:. MAX. DISANCE BEWEEN ERMINAL BXES IS 000' (0m) USING CMPUER GRADE CABLE 8 AWG. IF LESS HAN 7 FEE, JJ0007 CABLE MAY BE RUN DIRECLY WIHU ERMINAL BXES GREEN (XMI) 7 6 5 RED (RCD) B W S GREEN (XMI) 5 6 W B 8 AWG SHIELDED WISED PAIR BELDEN 8760 R EQUIVALEN JJ7 7 8 BRWN (GRD) HP007 ERMINAL BX S RS- MNIR MNIR MNIR MNIR 8 7 6 5 A A A A A A A A B B B B B B B B J U U U U U U U U U A 650 650A
YPICAL SYSEM CNNECINS 50 08 GRUP DAA LINE R R R R R R R R B W S N NC C IN PWER ALARM CDE R R R R R R R R R R R R R R R R R R R R R R R R C M INPU UPU 0V 60Hz U HP007 ERMINAL BX BRWN (GRD) 8 JJ0007 08 7 NES:. MAX. DISANCE BEWEEN ERMINAL BXES IS 000' (0m) USING CMPUER GRADE CABLE 8 AWG. IF LESS HAN 7 FEE, JJ0007 CABLE MAY BE RUN DIRECLY WIHU ERMINAL BXES GREEN (XMI) 6 5 RED (RCD) B W S RED (RCD) GREEN (XMI) 8 AWG SHIELDED WISED PAIR BELDEN 8760 R EQUIVALEN 5 6 7 B W S JJ7 8 BRWN (GRD) HP007 ERMINAL BX CAMERAS 5 7 9 5 7 9 5 7 9 6 8 0 6 8 0 6 8 0 ALARMS RELAY MNIRS 5 -CDE- BWS BWS BWS BWS 0V 60Hz KEYBARDS RS PRS 5 50 A
Declaration of Conformity Manufacturer: Sensormatic CCV Systems Division Manufacturer s Address: Sensormatic CCV Systems Division Sensormatic CCV Systems Division Blue Hill Plaza 600 Bradley Hill Road Pearl River, New York, 0965 USA Blauvelt, NY 09 USA Sensormatic Electronics Corporation State Rd. 0 Km 5.8 Poblado San Antonio Aguadilla P.R. 00690 Sensormatic Electronics Corporation (IRL) LD Melbourn Road, Bishopstown Cork, Ireland Declares, that the product(s) listed below: Name/ype: Model Number: Code ranslator ADS08/0X complies with the EMC Standards EN550 (Class B), EN5008-, and also complies with the following safety standard: EN60950. Additional information: hese products herein, comply with the requirements of the EMC Directive 89/6/EEC, and with the Low Voltage Directive (LVD) 7//EEC. he equipment was tested in a typical configuration. Pearl River, NY, USA February, 997 Ed hompson Engineering Manager European Contact: Sensormatic GmbH Am Schimmersfeld 7, 0880 Ratingen, Germany
SPECIFICAINS Electrical Ratings: AD08/0: 0 VAC, 50/60 Hz, 8 W ADS08/0X 0 VAC, 50/60 Hz, 00 ma Alarm Relay Contacts: Contact Ratings: SPD Form C, unpowered 0. A at VAC,.0 A at 0 VDC Mounting: Free standing or rack Weight: 7 lbs. Dimensions:.5" H x 7" W x 7.75" D (89 x x 97 mm) An American Dynamics Product Designed and built by Sensormatic CCV Systems Division ne Blue Hill Plaza Pearl River, New York, 0965 Business: (9) 6-7600 echnical Support Center: -800--5 FAX: (9) 6-7685 8000-096-0 P08-0G February, 997 Printed in USA