42048-4_Sani-Cide EX3_20161213_5_42048_.pdf Sani-Cide FX3. Disinfectant. Cleaner. For Use on Airplane Hard Surfaces L-Lactic Acid.0.4% INERT INGREDIENTS: 99.6% TOTAL:... 100.0% NET C0NTENTS: US gal (3.79 L) EPA REG. N0.42048-4 EpA EST. N0.42048-MD-001 6 airplane cabins. Sani-Cide EX3 has been tested according to Aerospace Material Specification (AMS) 15508, il3 is an effective disinfechnt against Staphy/ococcus aureus (ATCC 653S) and Salmonella enterica (ATCC 10708) APPLICATION INSTBUCTI0NS: Prior to disinfection, pre-clean hard surfaces by spraying Sani-Cide EX3 direcüy on T0 D $INFECT: Spray Sani-Cide EX3 direcüy on to the hard surface. Spray 6-8 inches from surface. Treated. Causes moderate eye initation. Avoid contact with eyes, skin, or clothing. Wear goggles, face ^
is a disinfectant and All-purpose Cleaner which leaves surfaces wiü a Streak-Free appearance and leaves afresh pleasantscent. Use Sani-Cide EX3 on hard, non-porous surfaces in airplane cabins where bacteria or süong unpleasant odors are likely to be present Sani-Cide EX3 will NOT discolor hard, non-porous surfaces in airplane cabins. Sani-Cide EX3 has been tested according to Aerospace MaterialSpecification (AMS) 15508, 1 452C and Boeing D6-71 27 test specifications. It is a violation of Federal Law to use üis product in a manner inconsistent wiü its labeling. workspaces and on any oüer objects or surfaces which passengers and crew may come in conþct with. Sani-Cide EX3 is an effective disinfectant against Sfapfylococ cus aureus (ATCC 6538) and Salmonella enterica (ATCC 1 0708) APPLIGATI0N IIISTRUCTI0NS: Prior to disinfection, pre-clean hard surfaces by spraying Sani-Cide EX3 direcüy on to üe surface. Spray 6-8 inches Trom surface fien wipe with a cloth and let dry. T0 DISIIIFEGT: Spray Sani-Cide EX3 direcüy on to the hard surface. Spray 6-8 inches from surface. Treated surfaces musl remain wet foll0 minutes. After 10 minutes, wipe (dry if desired) with a cloth and let dry. CAUT ON. Causes moderate eye irrihtion. Avoid contact with eyes, skin, or clotring. Wear goggles, face eating, drinking, chewing gum, using tobacco or using the toilet. Prolonged orfrequenüy repeated skin contact lf ln EYES: Hold eye open and rinse slowly and genfly wiü water for 15-20 minutes. Remove contact lenses, if present, after üe first 5 minutes, üen continue rinsing. Call a poison control center or doctor for feaínent advice. lf 0N SKIN: ïake off contaminated clothing. Rinse skin immediately wiür plenty 0f waler for 15-20 minutes. Call a poison control center or doctor for featnent advice. HOT tlne NUMBER: Have üe product conhiner or labelwiür you when calling a poison coníol center or doctor, or going for featment. You may also contact 1-800-424-9300 for emergency medical teafnent information. PESTICIDE STORAGE: Slore in a cool, dry, well-ventilated area inaccessible to children. lf leak or spill occurs - ventilate area of leak or spill. Remove all sources of ignition. Dilute wiü water and mop-up or absorb wiü an inert material (e.9., vermiculite, dry sand, earth) and place in a chemical waste container, PESTICIDE DISPOSAL: Wastes resufting from üe use of üris product must be disposed of on-site 0r at an approved waste disposal facility. C0NTAINER DISP0$A[: Nonrefillable container. Do not reuse or refilltris conhiner. Triple rinse container prompüy after emptying. Triple rinse as follows: Empty üre remaining contents into application equipment or mix tank and drain for 10 seconds atter the flow begins to drip. Fillüe container % full wiü water and recap. Shake for 10 seconds after the flow begins t0 drip. Repeat this procedure two more times. Then offer for recycling or dispose of in a sanihry landfill. Celeste lndüshies Corporat on. + +1.410.822.5775 8221 Teal Drive Suite 405, Easton, MD 21 601 A
NET CONTENTS: US gal (3.79 L) airplane cabins. Sani-Cide EX3 has been tested according to Aerospace Material Specification (AMS) 1550B, EX3 is an effective disinfectant against Staphylococcus aureus (ATCC 6538) and Salmonella enterica (ATCC 10708). APPLICATION INSTRUCTIONS: Prior to disinfection, pre-clean hard surfaces by spraying Sani-Cide EX3 directly on TO DISINFECT: Spray Sani-Cide EX3 directly on to the hard surface. Spray 6-8 inches from surface. Treated. Causes moderate eye irritation. Avoid contact with eyes, skin, or clothing. Wear goggles, face IF IN EYES: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing. Call a poison control center or doctor for treatment advice. IF ON SKIN: Take off contaminated clothing. Rinse skin immediately with plenty of water for 15-20 minutes. Call a poison control center or doctor for treatment advice. HOT LINE NUMBER: Have the product container or label with you when calling a poison control center or doctor, or going for treatment. You may also contact 1-800-424-9300 for emergency medical treatment information. PESTICIDE STORAGE: Store in a cool, dry, well-ventilated area inaccessible to children. If leak or spill occurs ventilate area of leak or spill. Remove all sources of ignition. Dilute with water and mop-up or absorb with an inert material (e.g., vermiculite, dry sand, earth) and place in a chemical waste container. PESTICIDE DISPOSAL: Wastes resulting from the use of this product must be disposed of on-site or at an approved waste disposal facility. CONTAINER DISPOSAL: Nonrefillable container. Do not reuse or refill this container. Triple rinse container promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or mix tank and drain for 10 seconds after the flow begins to drip. Fill the container ¼ full with water and recap. Shake for 10 seconds after the flow begins to drip. Repeat this procedure two more times. Then offer for recycling or dispose of in a sanitary landfill.
NET CONTENTS: US quart (946 ml) airplane cabins. Sani-Cide EX3 has been tested according to Aerospace Material Specification (AMS) 1550B, EX3 is an effective disinfectant against Staphylococcus aureus (ATCC 6538) and Salmonella enterica (ATCC 10708). APPLICATION INSTRUCTIONS: Prior to disinfection, pre-clean hard surfaces by spraying Sani-Cide EX3 directly on TO DISINFECT: Spray Sani-Cide EX3 directly on to the hard surface. Spray 6-8 inches from surface. Treated. Causes moderate eye irritation. Avoid contact with eyes, skin, or clothing. Wear goggles, face IF IN EYES: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing. Call a poison control center or doctor for treatment advice. IF ON SKIN: Take off contaminated clothing. Rinse skin immediately with plenty of water for 15-20 minutes. Call a poison control center or doctor for treatment advice. HOT LINE NUMBER: Have the product container or label with you when calling a poison control center or doctor, or going for treatment. You may also contact 1-800-424-9300 for emergency medical treatment information. PESTICIDE STORAGE: Store in a cool, dry, well-ventilated area inaccessible to children. If leak or spill occurs ventilate area of leak or spill. Remove all sources of ignition. Dilute with water and mop-up or absorb with an inert material (e.g., vermiculite, dry sand, earth) and place in a chemical waste container. PESTICIDE DISPOSAL: Wastes resulting from the use of this product must be disposed of on-site or at an approved waste disposal facility. CONTAINER DISPOSAL: Nonrefillable container. Do not reuse or refill this container. Triple rinse container promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or mix tank and drain for 10 seconds after the flow begins to drip. Fill the container ¼ full with water and recap. Shake for 10 seconds after the flow begins to drip. Repeat this procedure two more times. Then offer for recycling or dispose of in a sanitary landfill.
NET CONTENTS: 55 US gal (208 L) airplane cabins. Sani-Cide EX3 has been tested according to Aerospace Material Specification (AMS) 1550B, EX3 is an effective disinfectant against Staphylococcus aureus (ATCC 6538) and Salmonella enterica (ATCC 10708). APPLICATION INSTRUCTIONS: Prior to disinfection, pre-clean hard surfaces by spraying Sani-Cide EX3 directly on TO DISINFECT: Spray Sani-Cide EX3 directly on to the hard surface. Spray 6-8 inches from surface. Treated. Causes moderate eye irritation. Avoid contact with eyes, skin, or clothing. Wear goggles, face IF IN EYES: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing. Call a poison control center or doctor for treatment advice. IF ON SKIN: Take off contaminated clothing. Rinse skin immediately with plenty of water for 15-20 minutes. Call a poison control center or doctor for treatment advice. HOT LINE NUMBER: Have the product container or label with you when calling a poison control center or doctor, or going for treatment. You may also contact 1-800-424-9300 for emergency medical treatment information. PESTICIDE STORAGE: Store in a cool, dry, well-ventilated area inaccessible to children. If leak or spill occurs ventilate area of leak or spill. Remove all sources of ignition. Dilute with water and mop-up or absorb with an inert material (e.g., vermiculite, dry sand, earth) and place in a chemical waste container. PESTICIDE DISPOSAL: Wastes resulting from the use of this product must be disposed of on-site or at an approved waste disposal facility. CONTAINER DISPOSAL: Nonrefillable container. Do not reuse or refill this container. Triple rinse container promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or mix tank. Fill the container ¼ full with water. Replace and tighten closures. Tip the container on its side and roll it back and forth, ensuring at least one complete revolution, for 30 seconds. Stand container on its end and tip back and forth several times. Turn the container over onto its other end and tip it back and forth several times. Empty the rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Repeat the procedure two more times. Then offer for recycling or dispose of in a sanitary landfill. ENVIRONMENTAL HAZARDS Do not discharge effluent containing this product into lakes, streams, ponds, estuaries, oceans, or other waters unless in accordance with the requirements of a National Pollutant Discharge Elimination System (NPDES) permit and the permitting authority has been notified in writing prior to discharge. Do not discharge effluent containing this product to sewer systems without previously notifying the local sewage treatment plant authority. For guidance, contact your State Water Board or Regional Office of the EPA.
NET CONTENTS: 6 oz (177 ml) See inside for First Aid and Precautionary Statements Sani-Cide EX3 is a disinfectant and All-purpose Cleaner which leaves surfaces with a Streak-Free appearance and leaves a fresh pleasant scent. Use Sani-Cide EX3 on hard, non-porous surfaces in airplane cabins where bacteria or strong unpleasant odors are likely to be present. Sani-Cide EX3 will NOT discolor hard, non-porous surfaces in airplane cabins. Sani-Cide EX3 has been tested according to Aerospace Material Specification (AMS) 1550B, It is a violation of Federal Law to use this product in a manner inconsistent with its labeling. Use Sani-Cide EX3 to disinfect airplane hard surfaces such as tray tables, armrests, lavatory door handles, galley workspaces and on any other objects or surfaces which passengers and crew may come in contact with. Sani-Cide EX3 is an effective disinfectant against Staphylococcus aureus (ATCC 6538) and Salmonella enterica (ATCC 10708). APPLICATION INSTRUCTIONS: Prior to disinfection, pre-clean hard surfaces by spraying Sani-Cide EX3 directly on to the surface. Spray 6-8 inches from surface then wipe with a cloth and let dry. TO DISINFECT: Spray Sani-Cide EX3 directly on to the hard surface. Spray 6-8 inches from surface. Treated surfaces must remain wet for 10 minutes. After 10 minutes, wipe (dry if desired) with a cloth and let dry.. Causes moderate eye irritation. Avoid contact with eyes, skin, or clothing. Wear goggles, face shield or safety glasses and rubber gloves. Wash thoroughly with soap and water after handling and before eating, drinking, chewing gum, using tobacco or using the toilet. Prolonged or frequently repeated skin contact IF IN EYES: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing. Call a poison control center or doctor for treatment advice. IF ON SKIN: Take off contaminated clothing. Rinse skin immediately with plenty of water for 15-20 minutes. Call a poison control center or doctor for treatment advice. HOT LINE NUMBER: Have the product container or label with you when calling a poison control center or doctor, or going for treatment. You may also contact 1-800-424-9300 for emergency medical treatment information. PESTICIDE STORAGE: Store in a cool, dry, well-ventilated area inaccessible to children. If leak or spill occurs ventilate area of leak or spill. Remove all sources of ignition. Dilute with water and mop-up or absorb with an inert material (e.g., vermiculite, dry sand, earth) and place in a chemical waste container. PESTICIDE DISPOSAL: Wastes resulting from the use of this product must be disposed of on-site or at an approved waste disposal facility. CONTAINER DISPOSAL: Nonrefillable container. Do not reuse or refill this container. Triple rinse container promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or mix tank and drain for 10 seconds after the flow begins to drip. Fill the container ¼ full with water and recap. Shake for 10 seconds after the flow begins to drip. Repeat this procedure two more times. Then offer for recycling or dispose of in a sanitary landfill.