I-TEC I30A1D-I60A1D 2-Stage Compressor High Efficiency Air Source Air Conditioners w/dehumidification

I-TEC I30AD-IAD 2-Stage Compressor High Efficiency Air Source Air Conditioners w/dehumidification Cooling Capacities: 20,0 to 54,000 Btuh The Bard I-TEC Air Conditioner system is designed for classrooms and other similar applications demanding high efficiency and the lowest possible sound levels that are practical and achievable, and also accommodates the over-the-window sill requirement for many replacement projects on older school buildings. The I-TEC Series meets that challenge with many innovative design features resulting in a highly refined appearance while at the same time improving on the very important maintenance and serviceability features needed by the facilities maintenance and service staffs. I-TEC Standard Features All models have dehumidification (hot gas reheat) Double wall construction, 20-ga. exterior skin, no visible fasteners No fiberglass insulation Hinged, lockable, removable doors Removable sides and modularized construction for transporting through standard doors or in elevators allows installation on second and third floor Can be installed in left or right corners with no modifications Non-corrosive drainpans with no standing water 2-Stage scroll compressors with discharge muffler, double floating isolation mounting system, and sound muffling cover for ultra quiet operation R-4A Green Refrigerant Cooling thermostatic expansion valves Extra large full width control panel for easy access to all controls Circuit Breakers on 230V models, and Toggle Disconnect on 4V Evaporator coils constructed with hydrophilic fin stock with the following advantages: Acrylic coating Wettable surface with low contact angle no bead-up condensate, lower wet-coil air-side pressure drop, improved draining & lower re-entrainment of moisture back into the air stream in continuous blower operating modes Antimicrobial properties provide microbial resistance to fungicidal growth Resistant to Mold and Mildew, ASTM D3273 no growth Seals fin surface against aluminum oxide formation 24VAC 75VA control transformer with circuit breaker 24VAC low-voltage terminal strip for thermostat or DDC control ECM indoor and outdoor motors Modulating outdoor fan motor and low ambient control Modulating indoor fan motor for constant CFM in different operating modes up to 0.50" ESP High and Low Pressure switches with lockout circuit Liquid line filter/drier Readily accessible service ports located behind locking hinged doors Pleated 2" MERV filter Designed for over-the-window sill wall penetration and has 3" vertical adjustment for wall sleeve attachment I-TEC Optional Features & Accessories Four Ventilation Options: Both ERV and CRV have ECM motors, filter system, and positive shut-off. Energy Recovery Ventilator (ERV) is designed for both modulating or fixed supply and exhaust airflow operation depending upon environmental controls used, and has positive shutoff on intake and exhaust sides when unoccupied. Modulating mode requires CO 2 controller, has intake rate that is higher than exhaust, and has optional minimum CFM to address building IAQ requirements. The system modulates to maintain selected maximum CO 2 level. Fixed mode can be used with thermostat or DDC that has a dedicated Occupied output that is ON during Occupied and OFF during Unoccupied. Intake and exhaust rates can be independently adjusted. Commercial Room Ventilator (CRV Option M) is a fan powered ventilation package to manage intake & exhaust air at fixed rates but without energy recovery capability. The rates are: 300-375-450-525 CFM, are independently selectable & has positive shutoff on intake and exhaust sides when unoccupied. Requires control system that has a dedicated ventilation control output to be ON during Occupied and OFF during Unoccupied. CO2 controller with ON/OFF output relay can be used. Factory setting is 375 CFM balanced to meet pressurization requirements of ASHRAE. Commercial Room Ventilator (CRV Option N) is same as CRV Option M and also has a free-cooling economizer mode that can provide up to 525 CFM when the outdoor ambient temperature is below the set point of the outdoor thermostat. Units designed to be flush to a smooth interior wall and not require trim kits by use of adjustable wall sleeves; Trim Kits available where required Low sound levels are achieved by numerous system design innovations including special acoustical insulation Installation flexibility. Can be installed in corner applications with one side against a wall. Condensate overflow detection system with diagnostics monitors equipment and shuts down compressor to prevent condensate overflow. Freezestat on indoor coil safeguards against indoor coil freeze up by shutting down the compressor. Commercial Room Ventilator (CRV Option Q) is modulating design that requires 0-Vdc control signal from CO 2 controller. Other Options: Hot water coil packages, both Duct-Free and Ducted versions available. Accessories: See Page 2 & 3. ERV MIS-374 CRV MIS-3742 Form No S344-97 Supersedes S344-7 Page of 22

Specifications - 2½ through 3½ Ton MODELS I30ADA I30ADB I30ADC I3ADA I3ADB I3ADC I42ADA I42ADB I42ADC ELECTRICAL RATING-- HZ 230/20-230/20-3 4-3 230/20-230/20-3 4-3 230/20-230/20-3 4-3 Operating Voltage Range 97-253 44-50 97-253 44-50 97-253 44-50 COMPRESSOR Volts 230/20-230/20-3 4-3 230/20-230/20-3 4-3 230/20-230/20-3 4-3 Rated Load Amps (230/20).0/.5 7.4/.4 4.2./3.5/9.9 4.9 3./5..0/2.4 5.5 Branch Circuit Selection Current 3..7 4.3 5.3.7 5..0 4.2.3 Locked Rotor Amps 73 5 2 3 73 3 9 44 ENERGY RECOVERY VENTILATOR Volts 230/20-- 230/20-- 230/20-- Full Load Amps (3-motors) 2.2 2.2 2.2 FAN MOTOR ECM Horsepower /3 /3 /3 Volts 230/20-- 230/20-- 230/20-- Full Load Amps.7 2. 2. + CFM 950 2300 2300 BLOWER MOTOR ECM Horsepower /3 /2 /2 Volts 230/20-- 230/20-- 230/20-- Full Load Amps.9 2.5 2.5 + CFM @ rating points, will modulate based upon O.D. ambient. Specifications - 4 and 5 Ton MODELS I4ADA I4ADB I4ADC IADA IADB IADC ELECTRICAL RATING-- HZ 230/20-230/20-3 4-3 230/20-230/20-3 4-3 Operating Voltage Range 97-253 44-50 97-253 44-50 COMPRESSOR Volts 230/20-230/20-3 4-3 230/20-230/20-3 4-3 Rated Load Amps (230/20) 5./7.5.4/. 5.4 22/23.4 3.4/4.3.3 Branch Circuit Selection Current 9.9..4 27.2. 7.2 Locked Rotor Amps 4.0 3. 4 52.9.0 52.0 ENERGY RECOVERY VENTILATOR Volts 230/20-- 230/20-- Full Load Amps (3-motors) 2.2 2.2 FAN MOTOR ECM Horsepower /2 /2 Volts 230/20-- 230/20-- Full Load Amps 3.2 3.2 + CFM 20 20 BLOWER MOTOR ECM Horsepower /2 3/4 Volts 230/20-- 230/20-- Full Load Amps 3.2 4.4 + CFM @ rating points, will modulate based upon O.D. ambient. Complies with efficiency requirements of ANSI/ASHRAE/IESNA 90.-203. Certified to ANSI/ARI Standard 390-2003 for SPVU (Single Package Vertical Units). Intertek ETL Listed to Standard for Safety Heating and Cooling Equipment ANSI/UL 995/CSA 22.2 No. 23-05, Fourth Edition. Intertek ETL Listed to Standard for Gas-Fired Central Furnaces ANSI Z2.47-200, CSA 2.3-200 Fifth Edition, Addenda A dated -0-2007, Addenda B dated 0-0-200. Commercial Product - Not intended for Residential application. Bard is an ISO 900:200 Certified Manufacturer Form No S344-97 Supersedes S344-7 Page 2 of 22

Capacity and Efficiency Ratings (Stage 2) Full Load Operation MODELS I30A I3A I42A I4A IA Cooling BTUH, Full Load Capacity, 95-0/7 EER j Rated CFM 27,00.7 900,000 2.0 50 4,500.9 300 47,000.3 500 IPLV (Integrated Full & Part Load) k 0-0/7 5.4.5.0. 4. 54,000.7 700 Capacity and Efficiency Ratings (Stage ) Part Load Operation MODELS I30A I3A I42A I4A IA Cooling BTUH, Part Load Capacity, 95-0/7 EER j Rated CFM 20,0. 50 25,000 2.7 50 29,000 2. 950 32,500 2.0 50 37,000.0 200 EER = Energy Efficiency Ratio - BTU/WATT efficiency IPLV = Integrated Part Load Value - BTU/WATT efficiency (combines full and part load performance) Blower Performance j Model Rated ESP. Max. ESP k Continuous CFM Rated 2nd Stage CFM Motor will deliver consistent CFM through voltage supply range with no deterioration. Continous fan CFM is the total air being circulated during continuous fan mode. Rated st Stage CFM 4- KW CFM 5-20 KW CFM I30A 0.5 0.50 500 900 50 700 50 I3A 0.5 0.50 0 50 50 700 50 I42A 0.20 0.50 50 300 950 700 50 I4A 0.20 0.50 725 500 50 700 400 IA 0.20 0.50 50 700 200 700 400 Unit Weights MODELS NO VENT CRV ERV I30ADA 30 920 955 I30ADB 30 920 955 I30ADC 5 955 990 I3ADA 5 950 95 I3ADB 5 950 95 I3ADC 93 95 20 I42ADA 90 00 I42ADB 90 00 I42ADC 943 70 I4ADA 930 22 57 I4ADB 930 22 57 I4ADC 95 57 92 IADA 943 70 IADB 943 70 IADC 97 70 5 Deduct 49# from all values for installed weight. Unit Charge Rates UNIT I30AD - High Efficiency A/C, Dehum. Only I3AD - High Efficiency A/C, Dehum. Only I42AD - High Efficiency A/C, Dehum. Only I4AD - High Efficiency A/C, Dehum. Only IAD - High Efficiency A/C, Dehum. Only Std. Unit - Lbs. Dehum. Units - Lbs. N/A.25 N/A.25 N/A.75 N/A 3.25 N/A 3.325 Form No S344-97 Supersedes S344-7 Page 3 of 22

Factory Built-in Electric Heat Table Model Voltage Phase KW Amps BTUH 240 20 240 20 240 20 DA04 240/20 4 3.7 4.4 3,52,239 DA05 240/20 5.00 3.75 20..0 7,05 2,799 DA 240/20.00 7.50 4.7 3. 34,30 25,59 DA5 240/20 5.00.25 2.5 54. 5,95 3,39 DA20 240/20 20.00 5.00 3.3 72.,2 5,95 DB0 240/20 3.00 4.50 4.4 2.5 20,47 5,9 DB09 240/20 3 9.00.75 2.7.7 30,77 23,03 DB5 240/20 3 5.00.25 3. 3.2 5,95 3,39 DB 240/20 3.00 3.50 43.3 37.5,434 4,07 Model Voltage Phase KW Amps BTUH 40V 4V 40V 4V 40V 4V DC0 40 3.00 5.52 7.2.9 20,47,40 DC09 40 3 9.00.2..4 30,77 2,2 DC5 40 3 5.00 3.0.0 7.3 5,95 47,099 DC 40 3.00.5 2.7 20.,434 5,59 NOTE: Not all KW's available in all models. See Minimum Circuit Ampacity and Maximum Overcurrent Protection table on following page. Optional IHWC Hot Water Coil Performance - Heating Capacity @ 0 F Water & 70 F Return Air GPM CFM 00 900 00 0 200 300 400 500 0 700.5 32,000 32,7 33,333 34,000 34,500,000,500 3,000 3,400 3,750 2 42,000 43,200 44,400 45,0 4,400 47,200 4,000 4,500 49,000 49,500 3 49,000 5,7 53,750 57,000 59,400,750 4,000 5,200,000 7,000 4 5,000 59,000 2,000 5,000 9,000 73,000 77,000 79,500 2,000 4,000 5 59,000 2,53,7 9,750 72,33 75,97 79,000,000 3,000 5,000 2,000,7 70,333 74,500 77,000 79,500 2,000 3,500 5,000,500 7 3,500 7,70 7,97 7,25 7,97,70 4,500,500,000 9,200 5,000 9,250 73,500 77,750 0,33 3,97 7,000,900 90,500 9,750 9,000 70,525 75,050 79,575 2,3,92 9,500 9,500 93,000 94,500 7,000 7,00 7,0,400 4,933,47 92,000 94,500 9,000 97,500 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature (F) 0 20 30 40 50 70 0 90 200 50 0.455 0.545 0.3 0.727 0. 0.909.000.09.2.273.34 55 0.409 0.500 0.59 0.2 0.773 0.4 0.955.045.3.227.3 0.33 0.455 0.545 0.3 0.727 0. 0.909.000.09.2.273 5 0.3 0.409 0.500 0.59 0.2 0.773 0.4 0.955.045.3.227 70 0.272 0.33 0.455 0.545 0.3 0.727 0. 0.909.000.09.2 75 0.227 0.3 0.409 0.500 0.59 0.2 0.773 0.4 0.955.045.3 0 0.2 0.272 0.33 0.455 0.545 0.3 0.727 0. 0.909.000.09 Form No S344-97 Supersedes S344-7 Page 4 of 22

Minimum Circuit Ampacity & Maximum Overcurrent Protection Single Circuit Dual Circuit MODEL Rated Volts, Hertz & Phase No. Field Power Circuits Minimum Circuit Ampacity Maximum External Fuse or Ckt. Brkr. Field Power Wire Size Ground Wire Minimum Circuit Ampacity Maximum External Fuse or Ckt. Breaker Field Power Wire Size Ground Wire Size Ckt. A Ckt. B Ckt. A Ckt. B Ckt. A Ckt. B Ckt. A Ckt. B I30ADA0Z A05 A 230/20-22 32 5 I30ADB0Z B0 B09 230/20-3 7 23 32 25 25 I30ADC0Z C0 C09 4-3 9 3 5 20 4 4 2 4 4 2 I3ADA0Z A05 A A5 230/20- or 2 2 32 5 4 40 40 90 4 2 52 40 I3ADB0Z B0 B09 B5 230/20-3 22 23 32 5 30 30 I3ADC0Z C0 C09 C5 4-3 3 2 5 5 20 30 4 4 2 4 4 2 I42ADA0Z A05 A A5 230/20- or 2 30 32 5 4 45 40 90 4 30 52 40 I42ADB0Z B0 B09 B5 230/20-3 25 25 32 52 I42ADC0Z C0 C09 C5 4-3 2 4 9 2 5 5 20 30 4 4 2 4 4 2 I4ADA0Z A05 A A5 A20 230/20- or 2 or 2 34 34 59 5 50 50 90 3 2 59 52 52 45 I4ADB0Z B0 B09 B5 B 230/20-3 2 2 34 53 53 I4ADC0Z C0 C09 C5 C 4-3 2 4 9 29 33 5 5 20 30 2 2 2 2 2 2 IADA0Z A05 A A5 A20 230/20- or 2 or 2 44 44 59 9 2 0 20 3 2 44 52 52 IADB0Z B0 B09 B5 B 230/20-3 or 2 3 3 53 53 45 45 45 3 54 45 IADC0Z C0 C09 C5 C 4-3 5 5 9 29 33 20 20 20 30 2 2 2 2 2 2 These Minimum Circuit Ampacity values are to be used for sizing the field power conductors. Refer to the National Electric Code (latest revision), Article 3 for power conductor sizing. Caution: When more than one field power conductor circuit is run through one conduit, the conductors must be derated. Pay special attention to note of table 3 regarding Ampacity Adjustment Factors when more than three (3) current carrying conductors are in a raceway. Maximum size of the time delay fuse or HVAC type circuit breaker for protection of field wiring conductors. Based on 75 C copper wire. All wiring must conform to the National Electrical Code and all local codes. Form No S344-97 Supersedes S344-7 Page 5 of 22

Cooling Full Load Application Data Model I30A I3A I42A I4A IA D.B. / W.B. j 75/2 0/7 5/72 75/2 0/7 5/72 75/2 0/7 5/72 75/2 0/7 5/72 75/2 0/7 5/72 COOLING CAPACITY F 5 F 70 F 75 F 0 F 5 F 90 F 95 F 0 F 5 F F 5 F 20 F 25 F 30,74 23,57 33,4 23,9,990 23,0 39,03 30,2 42,49 30,7 45,32 30,57 4,5,042 5,03,75 54,,505 5,43 39,52 5,93 3,4 5,44 3,5,02 45,9 7,03 44, 72,34 44,530 30,05 23,29 32,75 23,4,372 23,272 3, 29,72 4,4 30,250 44,90 29,975 45,740 34, 49,725,23 53,3 34,92 50,52 3, 55,497 3,29 54,927 37,39 59,3 44,74 5,75 44,03 70,739 43,20 29,349 22,74 3,3 22,994 34,754 22,73 37,3 29,33 40,50 29,73 44,0 29,34 44, 34,33 4,43 34,79 52,3 34,33 49,0 3, 54,0 37,24 53,40 37, 57,575 43,790 3,33 43,244,44 42,7 2,4 22,2 3,050 22,500 34,3 22,204 3,459 2,93 39,525 29,75 43,454 2,792 43,492 33,975 47,50 34,200 5,3 33,75 47,49 37,39 52,4 37,029 5,9 3,44 55,3 42,40,450 42,425,550 4,00 Cooling Part Load Application Data Model I30A I3A I42A I4A IA D.B. / W.B. j 75/2 0/7 5/72 75/2 0/7 5/72 75/2 0/7 5/72 75/2 0/7 5/72 75/2 0/7 5/72 COOLING CAPACITY j Return air temp. F Rated CFM. 27,934 2,94 30,200 22,000 33,5 2,7, 2,54 3,500 2,0 42,727 2,200 42,3 33,20 44,500 32,75 50,37 33, 4,57 3, 5,000,950 50,39,0 54,07 4,90 59,5 4, 4,455 40,90 27,22 2,575 29,3 2,50 32,900 2,37 34,75 2,4 37,59 2,03 42,00 27, 4,244 33,24 43,23 32,5 49,37 32,5 45,5,97 49,54,5 4,50,29 52,343 40,939 57,725 40,7 2,3 39,90 2,59 2,7 2,3 2,09 32,22 20,3 33,905 27,75 3,5 27,53 4,275 27,0 40,20 32,909 43,2 32,44 4,3 3,99 43,54,2 4,4,245 47,33 34,45 50,599 39,99 55,3 39,99,25 39,070 25,2 20,799 27,00 20,525 3,4 20,09 33,054 27,,000 27,025 40,54 2,424 3,99 32,553 4,500 32,25 47,3 3,4 42,522 34,55 47,000 34,50 45, 33,774 4,55 39,039 54,000 39,50 5,70 3, 24,97 20,59 2,900 20,325 30,39 9,73 3,00 2,53 34,250 2,500 39,0 25,9 3,00 32,9 40,933 3,775 4,23 3,0 40,9 33,5 45,29 33,953 44,075 33,094 47,3 3,42 52,4 3,592 5,397 37, 24,40 20,393 2,000 20,25 29,4 9,7 30,547 2,32 32,900 25,975 37,473 25,39 37,05 3,43 39,7 3,424 45,40 30,72 39,299 33, 43,437 33,25 42,339 32,45 45,77 37,92 50,70 3,034 54,24 37,072 23,305 20,9 25,0 9,925 2,59 9,42 29,293 25,79 3,550 25,450,9 24,4 3,025 3,4 3,00 3,074 44,94 30,33 37,7 32,4 4,5 32,559 40,3 3,7 44,37 37,370 49,02 37,47 52,5 3,52 22,49 9,9 24,200 9,725 27,54 9,27 2,040 25,257 30,200 24,925 34,39 24,37,0 3,33 37,734 30,723 42,979 30,040 3,07 3,77 39,75 3,2 3, 3,05 42,9 3,3 47,45 3,9 5,077,95 2,33 9,75 23,300 9,525 2,539 9,09 2,77 24,725 2,50 24,400 32, 23,5 34,045 30,77 3,7 30,373 4,74 29,9 34,44 3,07 3,093 3,5 37,30 30,37 4,409 3,257 45,79 3,3 49,304,44 20,79 9,53 22,400 9,325 25,54,9 25,533 24,93 27,500 23,75 3,323 23,344 33,054 30,423, 30,022 40,549 29,5 32,52 30,3 3,32 30,47,394 29,97 39,99,70 44,23,02 47,53 34,97 F 5 F 70 F 75 F 0 F 5 F 90 F 95 F 0 F 5 F F 5 F 20 F 25 F 24,,25 2,025,000 27,27 7,242 29,45 23,790 32,000 23,43 33,542 22,4 30,04 25,9 32,43 24,3 33, 23,757 3,49 27,440 40,30 27,9 37,94 2,7 42,05 3,549 47,39 3,23 5,94 30,902 23,33 7,90 25,250 7,700 2,729 7,05 2,3 23,242 3,000 22,975 32,24 22,4 29,3 24,7 32,03 24,475 33,7 23,57,477 2,922 39,255 2,72 3,97 2,403 4,472 30,90 45, 30,50 50,334 30,29 22,5 7,5 24,475 7,400 2,90,9 27,720 22,94 30,000 22,4 32, 2,05 29,9 24,32 3,594 24,3 33,75 23,399 34,45 2,404 3,29 2,234 3,70 25,930 40,39 30,232 44,40 30,03 4,72 29,90 2, 7,24 23,700 7,0 25,52,3 2,75 22,4 29,000 22,000 3,3 2,43 2,75 23,95 3,75 23,00 33,742 23,220 33,453 25, 37,003 25,75 3,573 25,457 3,07 29,574 42,925 29,425 47,2 29,03 2,20, 22,00,75 25,3,497 25,79 2,599 27,0 2,75 30,70 2,22 2,332 23,555 32,000 23,0 33,79 23,040 32,44 25,39 3,000 25,24 3,3 24,94 37,474 2,9 4,000 2,500 45,55 2,477 20,372,59 22,025,375 24,575,3 24,33 2,05 2,0 20, 29,953 20,70 27,99 23,5 3,5 23,23 33,9 22, 3,429 24,5 34,74 24,73 3,59 24,5 3,42 2,25 39,59 27, 43,90 27,70 9,25,72 2,375,200 24,037,24 23,7 20,503 2,000 20,53 29,2 20,439 27,45 22,747 29,99 22,7 33,73 22,2 30,47 24,333 33,2 24,323,952 24,03 34,09 27,599 3,4 27,5 42,30 27,24,77 5,25 20,0 5,900 23,49 5,93 22,909 9,955 25,000 20,050 2,57 20,09 27,032 22,344 29,000 22,450 33,50 22,503 29,405 23,5 32,500 23,45,745 23,55 33,47 2,94 37,000 2,975 40,95 2,5,22 5,52 9,75 5,0 22,7 5,37 22,233 9,743 24,23 9,3 27,7 9,5 2,09 22,055 2,473 22, 32,479 22,23 2,404 23,52 3,394 23,542 34,529 23,25 32,47 2,55,90 2,9 39,492 2,30 7,54 5,227 9,50 5,300 2,44 5,33 2,557 9,532 23,525 9,25 2, 9,72 25,50 2,77 27,44 2,7 3,307 2,923 27,403 23,2 30,2 23,239 33,32 22,9 3,497 2,230 34,3 2,23 3,29 25,954,4 4,929,425 5,000 2,07 5,03 20, 9,32 22,7 9,43 25,993 9,459 24,209 2,479 2,49 2,5 30,3 2,33 2,402 22,907 29, 22,93 32,095 22, 30,50 25,74 33,79 25,90 37,0 25,2,29 4,30 7,700 4,700 20,90 4,7 20,20 9,9 22,050 9,200 25,52 9,24 23,2 2,9 25,392 2,292 2,94 2,342 25,40 22,4 2,075 22,33 30,79 22,37 29,5 25,5 32,25 25,550,3 25,250 5,555 4,332,975 4,400 9,33 4,434 9,530,9 2,33,9 24,3 9,033 22,327 20,903 24, 2,002 27,793 2,052 24,400 22,302 2,99 22,330 29,2 22,07 2,52 25,2 3,53 25,94 34, 24,97 4,9 4,033,250 4,0,53 4,33,54, 20,575,775 23,470,9 2,3 20,5 23,33 20,73 2,22 20,72 23,399 2,999 25,3 22,027 2,445 2,7 27,539 24,0 30,43 24,3 33,477 24,545 Form No S344-97 Supersedes S344-7 Page of 22

DEHUMIDIFICATION CIRCUIT The I**A models with standard dehumidification provide a unique circuit for periods of high indoor humidity conditions. Additionally, an energy recovery ventilator may be provided to allow for outside ventilation air requirements by eliminating excessive sensible and latent loads as a result of the increased ventilation requirement. The dehumidification circuit incorporates an independent heat exchanger coil in the supply air stream in addition to the standard evaporator coil. This coil reheats the supply air after it passes over the cooling coil, and is sized to nominally match the sensible cooling capacity of the evaporator coil. Extended run times in dehumidification mode can be achieved using waste heat from the refrigeration cycle to achieve the reheat process, while at the same time large amounts of moisture can be extracted from the passing air stream. See below for specific operating sequences, and see attached tables for performance on sensible and latent capacities, water removal ratings, and supply air delivery conditions. The dehumidification refrigerant reheat circuit is controlled by a 3-way valve directing the refrigerant gas to the normal condenser during periods when standard air conditioning is required. During periods of time of low ambient temperature (approximately 5 to 75 outdoor) and high indoor humidity, a humidistat senses the need for mechanical dehumidification. It then energizes both the compressor circuit and the 3-way valve, thus directing the hot refrigerant discharge gas into a separate desuperheating condenser circuit which reheats the conditioned air before it is delivered to the room. The refrigerant gas is then routed from the desuperheating condenser to the outdoor coils for further heat transfer. When the humidistat is satisfied, the system automatically switches back to normal A/C mode and either continues to operate or turns off based on the signal from the wall thermostat. The result is separate humidity control at minimum operating cost. DEHUMIDIFICATION SEQUENCE OF OPERATION Dehumidification is controlled through a humidistat and is independent of the thermostat. On a call for dehumidification mode of operation, the compressor will operate at full load (capacity) and 3-way valve that feeds the reheat coil is energized through D terminal. Dehumidification will continue until the humidistat is satisfied. Anytime there is a R-Y call for cooling, dehumidification is canceled and the unit will operate in the cooling mode at part load for Stage cooling (can shift to full load if 2nd Stage cooling required) until satisfied. If dehumidification call is still present when cooling call is satisfied, the unit will continue to operate and revert to dehumidification mode with compressor at full level. DEHUMIDIFICATION RELAY LOGIC BOARD Inputs to Board Outputs From Board G Y B W2 E A D RAT L G BK YO RV W E A2 TWV L Cooling Mode Unoccupied X X X X Cooling Mode Occupied X X X X X Cooling Mode w/dehum X X X X X Dehumidification Unoccupied X X X X Dehumidification Occupied X X X X X NOTE: Cooling takes precedence over dehumidification. A cooling call cancels dehumidification. Form No S344-97 Supersedes S344-7 Page 7 of 22

Outdoor Fan Left Condenser Coil Filter/Drier Cooling TXV Check Valves Fan Dehum. Reheat Coil Evaporator Coil 4 Way Reheat Valve Hi Press. Switch Low Press. Switch Right Condenser Coil Compressor ITEC Air Conditioner Cooling Mode Circuit Diagram MIS-325 Outdoor Fan Left Condenser Coil Filter/Drier Cooling TXV Check Valves Fan Dehum. Reheat Coil Evaporator Coil 4 Way Reheat Valve Hi Press. Switch Low Press. Switch Right Condenser Coil Compressor ITEC Air Conditioner Dehumidification Mode Circuit Diagram MIS-324 Form No S344-97 Supersedes S344-7 Page of 22

I30AD APPLICATION PERFORMANCE DATA Outdoor System Capacity Pounds of Water/Hour Evaporator Airflow Approximate Supply Air DB/WB %RH DB Total Sensible Latent S/T Lbs. CFM DB WB 5/3 90 5 3,375 3,550 7,25 43.2%. 50 50.7 50.3 A/C Mode A/C vs. Dehum 5/3 90 5 5,025 (,50),75 N/A 5.3 50.3 57.3 Dehum 75/2.5 50 75 2,25 2,0,525 7.%.2 50 52.0 5.0 A/C 75/2.5 50 75,900 3,50 5,250 N/A 5.0 50 7. 5.9 Dehum 75/5.5 75 30,700 9,250,450 2.7%. 50 54.5 53.5 A/C 75/5.5 75,400,775 9,25 N/A 9. 50 73..4 Dehum 75/ 70 75 32,0,725 5,375 52.% 4.5 50 57. 5.2 A/C 75/ 70 75 3,50 (0) 3,250 N/A 2.5 50 75. 3. Dehum 0/7 50 95 27,575 20,375 7,200 73.9%. 50 5. 5.7 A/C 0/7 50 95 2,25 (2,975) 5,0 N/A 5.3 50 3.3.0 Dehum I3AD APPLICATION PERFORMANCE DATA Outdoor System Capacity Pounds of Water/Hour Evaporator Airflow Approximate Supply Air DB/WB %RH DB Total Sensible Latent S/T Lbs. CFM DB WB 5/3 90 5 39,550,550 23,000 4.% 2.7 50 5.7 5.2 A/C Mode A/C vs. Dehum 5/3 90 5 7,950 (925),75 N/A 7. 50 5.7 57.9 Dehum 75/2.5 50 75 3,775 27,750 9,025 75.5.5 50 52. 5.3 A/C 75/2.5 50 75,000 5,025 5,975 45.7% 5. 50 70.9 59.3 Dehum 75/5.5 75 39,75 24,75 5,500.9% 4. 50 55. 54.3 A/C 75/5.5 75 3,000 3,075 9,925 23.7% 9.4 50 72.5 2.0 Dehum 75/ 70 75 4,25 2,300 20,325 5.2% 9.2 50 57.9 5. A/C 75/ 70 75 5,900,050 4,50.% 4.0 50 74. 4.0 Dehum 0/7 50 95 34,225 25,25,0 74.9%. 50 59.3 57.5 A/C 0/7 50 95 7,25 2,575 5,050 33.% 4. 50 2..7 Dehum I42AD APPLICATION PERFORMANCE DATA Outdoor System Capacity Pounds of Water/Hour Evaporator Airflow Approximate Supply Air DB/WB %RH DB Total Sensible Latent S/T Lbs. CFM DB WB 5/3 90 5 47,475,75 2,0 39.% 27.0 300 52.0 5.5 A/C Mode A/C vs. Dehum 5/3 90 5 20,75 (,925) 22,0 N/A 20. 300.3 5.2 Dehum 75/2.5 50 75 42,775 3,75,0 74.%.5 300 52.7 5.0 A/C 75/2.5 50 75,950 5,075,75 42.5%.5 300 7.3 59.5 Dehum 75/5.5 75 45,750 27,750,000.7% 7.0 300 55.4 54.0 A/C 75/5.5 75 5,325 2,25 2,700 7.% 2.0 300 73. 2.0 Dehum 75/ 70 75 4,075 24,300 23,775 50.5% 22.4 300 57. 5.7 A/C 75/ 70 75 7,75 250 7,425.4%.4 300 74. 4.2 Dehum 0/7 50 95 40,375 29,575,00 73.3%.2 300 59.2 57.2 A/C 0/7 50 95 325 (3,900) 4,225 N/A 4.0 300 2.. Dehum Form No S344-97 Supersedes S344-7 Page 9 of 22

I4AD APPLICATION PERFORMANCE DATA Outdoor System Capacity Pounds of Water/Hour Evaporator Airflow Approximate Supply Air DB/WB %RH DB Total Sensible Latent S/T Lbs. CFM DB WB 5/3 90 5 53,525 22,500 3,025 42.0% 29.3 550 5. 50. A/C Mode A/C vs. Dehum 5/3 90 5 20,575 (4,925) 25,500 N/A 24. 550.0 5. Dehum 75/2.5 50 75 50,0 3,25 2,225 75.7%.5 550 5.5 50.5 A/C 75/2.5 50 75 2,00 3,575 9,225 N/A.7 550 72.7 59.7 Dehum 75/5.5 75 53,750 32,975 20,775.3% 9. 550 54. 53.7 A/C 75/5.5 75 5,25 50 4,975 N/A 4. 550 74.4 2.3 Dehum 75/ 70 75 55,0 2,750 2,50 5.7% 25.3 550 57.2 5.4 A/C 75/ 70 75 7,500 (,75) 9,375 N/A.3 550 7. 4.7 Dehum 0/7 50 95 49,250 3,0 2,900 73.% 2.2 550 57. 5.4 A/C 0/7 50 95 (50) (7,300),450 N/A. 550 4. 7.2 Dehum IAD APPLICATION PERFORMANCE DATA Outdoor System Capacity Pounds of Water/Hour Evaporator Airflow Approximate Supply Air DB/WB %RH DB Total Sensible Latent S/T Lbs. CFM DB WB 5/3 90 5,000 25,925,075 42.5% 33. 750 5.4 50. A/C Mode A/C vs. Dehum 5/3 90 5,325 (,475) 24,00 N/A 23.4 750. 59. Dehum 75/2.5 50 75 5,425 44,475 3,950 7.% 3.2 750 52. 50. A/C 75/2.5 50 75 9,0 525,575 N/A. 750 74.. Dehum 75/5.5 75 2,000 3,25 23,375 2.3% 22. 750 55.0 53.9 A/C 75/5.5 75 2,50 (,700) 3,50 N/A 3. 750 7.0 3.4 Dehum 75/ 70 75 5,50 33,550 3,0 5.5% 29. 750 57. 5.5 A/C 75/ 70 75 4,950 (4,575) 9,525 N/A.4 750 77.4 5.5 Dehum 0/7 50 95 5,450 42,050 4,400 74.5% 3. 750 5. 5.7 A/C 0/7 50 95 (3,750) (,550),00 N/A.4 750 5. 7.5 Dehum Form No S344-97 Supersedes S344-7 Page of 22

Performance and Application Data Energy Recovery Vent Option "R" Ambient O.D. VENTILATION RATE 450 CFM 5% EFFICIENCY SUMMER COOLING PERFORMANCE (INDOOR DESIGN CONDITIONS 75 DB/2 WB) VENTILATION RATE 375 CFM % EFFICIENCY VENTILATION RATE 300 CFM 7% EFFICIENCY DB/WB F VLT VLS VLL HRT HRS HRL VLT VLS VLL HRT HRS HRL VLT VLS VLL HRT HRS HRL 75 245 450 4 3952 9477 4475 77 250 5737 05 0 37 43 9720 4590 957 52 3075 5 70 450 450 0 9477 9477 0 250 250 0 0 0 0 9720 9720 0 52 52 0 5 450 450 0 9477 9477 0 250 250 0 0 0 0 9720 9720 0 52 52 0 0 90 250 9440 20533 797 2 2325 25 200 7374 2 92 2 0 29 4 5427 3 75 245 250 934 3952 797 54 77 25 772 05 2 523 43 0 2 957 5427 4 0 70 22 250 202 029 797 3 293 25 793 2 2 0 557 5427 90 5 250 250 0 797 797 0 25 25 0 2 2 0 0 0 0 5427 5427 0 250 250 0 797 797 0 25 25 0 2 2 0 0 0 0 5427 5427 0 0 90 9720 270 20533 3 425 2325 0 225 7374 5345 202 2 40 450 4 434 97 75 245 9720 744 3952 3 734 77 0 977 05 5345 459 43 40 730 957 434 524 95 70 22 9720 232 029 3 7 293 0 293 793 5345 447 2 40 755 557 434 75 5 9720 9720 0 3 3 0 0 0 0 5345 5345 0 40 40 0 434 434 0 9720 9720 0 3 3 0 0 0 0 5345 5345 0 40 40 0 434 434 0 0 90 7290 24300 20533 473 5794 2325 75 20250 7374 4009 3 2 4 200 4 325 54 75 245 7290 475 3952 473 923 77 75 2 05 4009 779 43 4 9450 957 325 33 90 70 22 7290 502 029 473 3290 293 75 42 793 4009 274 2 4 3375 557 325 22 5 7290 7290 0 473 473 0 75 75 0 4009 4009 0 4 4 0 325 325 0 7290 7290 0 473 473 0 75 75 0 4009 4009 0 4 4 0 325 325 0 0 90 4 2730 20533 9 7374 2325 4050 22275 7374 272 470 2 3240 720 4 270 939 75 245 4 5 3952 9 793 77 4050 337 05 272 932 43 3240 70 957 270 74 5 70 22 4 7492 029 9 470 293 4050 243 793 272 420 2 3240 4995 557 270 334 5 4 4 0 9 9 0 4050 4050 0 272 272 0 3240 3240 0 270 270 0 4 4 0 9 9 0 4050 4050 0 272 272 0 3240 3240 0 270 270 0 75 245 2430 90 3952 579 2372 77 2025 52 05 33 49 43 20 290 957 5 502 0 70 22 2430 9922 029 579 449 293 2025 2 793 33 5457 2 20 5 557 5 4432 5 4252 2430 22 274 579 4 43 2025 5 233 33 02 2 20 25 99 5 4 2430 2430 0 579 579 0 2025 2025 0 33 33 0 20 20 0 5 5 0 70 22 0 22 029 0 029 293 0 293 793 0 793 2 0 2 557 0 557 75 5 4252 0 4252 274 0 274 43 0 43 233 0 233 2 0 2 99 0 99 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Ambient O.D. WINTER HEATING PERFORMANCE (INDOOR DESIGN CONDITIONS 70 F DB) 450 CFM 0% EFFICIENCY VENTILATION RATE 375 CFM % EFFICIENCY 300 CFM 2% EFFICIENCY DB/ F WVL WHR WVL WHR WVL WHR 5 2430 944 2025 40 20 32 4 3 4050 320 3240 25 55 7290 532 75 4920 4 395 50 9720 777 0 5 40 533 45 250 9720 25 20 0 42 40 450 4 250 94 9720 7970 70 3 475 4 340 929 30 9440 5552 200 322 29 27 25 270 749 225 472 450 955 20 24300 9440 20250 402 200 324 5 2730 234 22275 042 720 42 NOTE: Sensible performance only is shown for winter application. LEGEND: VLT = Ventilation Load - Total VLS = Ventilation Load - Sensible VLL = Ventilation Load - Latent HRT = Heat Recovery - Total HRS = Heat Recovery - Sensible HRL = Heat Recovery - Latent WVL = Winter Ventilation Load WHR = Winter Heat Recovery Form No S344-97 Supersedes S344-7 Page of 22

I-TEC Accessory Model Numbers Wall Sleeves (Required Option - Select One) j Model # Description j Above table based on I-TEC unit being installed flush to inside of wall. k " Hurricane Louvers are field supplied Total Depth of Wall System When Used with " Louver Total Depth of Wall System When Used with 2" Louver IWS-A Wall Sleeve Adjustable 5.5 to.5".5 to.5" IWS-B Wall Sleeve Adjustable.0 to 3.5" 9.0 to 3.5" IWS-C Wall Sleeve Adjustable 3.0 to 23.5" 4.0 to 23.5" Model # Description Total Depth of Wall System When Used with 4" Louver Total Depth of Wall System When Used with " Louver IWS-AH k Wall Sleeve Adjustable.0 to 2.0" IWS-BH k Wall Sleeve Adjustable 2.0 to 20.0" 2.0 to 5.0" IWS-CH k Wall Sleeve Adjustable 5.0 to 20.5" Outdoor Louver Grilles (Required Option - Select One) Model # Description Color Sleeve (Required) ILS- " Standard Anodized Aluminum IWS-A, -B, -C ILS-20 " Standard Aluminum with Medium Bronze Finish IWS-A, -B, -C ILS-30 " Standard Aluminum with Dark Bronze Finish IWS-A, -B, -C ILS-** " Standard Aluminum with Custom Finish IWS-A, -B, -C ILA2-2" Architectural Anodized Aluminum IWS-A, -B, -C ILA2-20 2" Architectural Aluminum with Medium Bronze Finish IWS-A, -B, -C ILA2-30 2" Architectural Aluminum with Dark Bronze Finish IWS-A, -B, -C ILA2-** 2" Architectural Aluminum with Custom Finish IWS-A, -B, -C ILST4-4" Storm Anodized Aluminum IWS-AH, -BH, -CH ILST4-20 4" Storm Aluminum with Medium Bronze Finish IWS-AH, -BH, -CH ILST4-30 4" Storm Aluminum with Dark Bronze Finish IWS-AH, -BH, -CH ILST4-** 4" Storm Aluminum with Custom Finish IWS-AH, -BH, -CH Additional Louver Colors Available Applies to ILS, ILA and ILST Louvers k -2 Arctic White -4 Storm White - Milano Beige -32 Jet Black -3 Graphite Gray -40 School Bus Yellow -42 Florida Orange -44 School House Red -4 Chili Red -50 Deep Sea Blue -52 Bahama Blue -54 Ivy Green -5 Sage Green k Available Special Order and requires additional lead-time. Reference Form S0 for additional details. Custom Finishes are quoted on a project-by-project basis and pricing is determined by quantity, finish option and size. Custom Finishes are ordered/shipped directly from the louver supplier. Purchaser of Custom Finishes assumes liability for quantity, finish match and size. Contact your Bard Sales Representative for custom louver contact information. Form No S344-97 Supersedes S344-7 Page 2 of 22

I-TEC Accessories Optional per Job Requirement Duct-Free Plenum Boxes Model #: Description: IPBDFH-X " Duct Free Plenum Beige. Black linear slot grilles, side w/shutoff damper IPBDFH- " Duct Free Plenum White. Black linear slot grilles, side w/shutoff damper IPBDFH-4 " Duct Free Plenum Gray. Black linear slot grilles, side w/shutoff damper IPBDFH2-X 2" Duct Free Plenum Beige. Black linear slot grilles, side w/shutoff damper IPBDFH2-2" Duct Free Plenum White. Black linear slot grilles, side w/shutoff damper IPBDFH2-4 2" Duct Free Plenum Gray. Black linear slot grilles, side w/shutoff damper IPBDF-X " Duct Free Plenum Beige. (2) Anodized dual deflection front & side grilles IPBDF- " Duct Free Plenum White. (2) Anodized dual deflection front & side grilles IPBDF-4 " Duct Free Plenum Gray. (2) Anodized dual deflection front & side grilles IPBDF2-X 2" Duct Free Plenum Beige. (2) Anodized dual deflection front & side grilles IPBDF2-2" Duct Free Plenum White. (2) Anodized dual deflection front & side grilles IPBDF2-4 2" Duct Free Plenum Gray. (2) Anodized dual deflection front & side grilles IPBDF-X " Duct Free Plenum Beige. Anodized dual deflection front & side grilles IPBDF- " Duct Free Plenum White. Anodized dual deflection front & side grilles IPBDF-4 " Duct Free Plenum Gray. Anodized dual deflection front & side grilles Duct-Free Plenum Boxes with Hot Water Coil Model #: Description: IPBDF2HW-X 2" Duct Free Plenum Beige. Anodized dual deflection front & side grilles, w/hot water coil IPBDF2HW- 2" Duct Free Plenum White. Anodized dual deflection front & side grilles, w/hot water coil IPBDF2HW-4 2" Duct Free Plenum Gray. Anodized dual deflection front & side grilles, w/hot water coil NOTE: No water control valves included. Field-Installed. Hot Water Coil with Duct Connection Model #: Description: IHWC Hot water coil assembly, mounts on top of I-TEC unit, " x 30" duct flange NOTE: No water control valves included. Field-Installed. NOTE: Order appropriate Cabinet Extension (Model ICX2-*) to enclose hot water coil assembly, valves, piping and ductwork. Cabinet Extensions Model #: Description: ICX2-X 2" extension for ceilings up to '2", beige paint ICX2-2" extension for ceilings up to '2", white paint ICX2-4 2" extension for ceilings up to '2", gray paint NOTE : Use of Riser Platforms will increase maximum ceiling height by riser height. NOTE 2: Cabinet Extensions can be used with ducted systems to enclose ductwork or piping, and can also be used with Duct-Free Plenum Boxes to enclose to ceiling if desired. Extensions can be trimmed tao height as needed. Riser Platforms Model #: Description: Model #: Description: IRP-3-X Riser platform 3" with trim kit, beige paint IRP-9-X Riser platform 9" with trim kit, beige paint IRP-3- Riser platform 3" with trim kit, white paint IRP-9- Riser platform 9" with trim kit, white paint IRP-3-4 Riser platform 3" with trim kit, gray paint IRP-9-4 Riser platform 9" with trim kit, gray paint IRP--X Riser platform " with trim kit, beige paint IRP--X Riser platform " with trim kit, beige paint IRP-- Riser platform " with trim kit, white paint IRP-- Riser platform " with trim kit, white paint IRP--4 Riser platform " with trim kit, gray paint IRP--4 Riser platform " with trim kit, gray paint NOTE: Use of Riser Platforms will increase maximum ceiling height by riser height. Wall Curbs Model #: ICURB740 Side Trim Kits Model #: Description: 7" Deep Curb to allow sleeve installation with a 40" window sill height Description: IST4-X 4" Side Trim Kit, beige paint, adaptable for ceilings up to 2' IST4-4" Side Trim Kit, white paint, adaptable for ceilings up to 2' IST4-4 4" Side Trim Kit, gray paint, adaptable for ceilings up to 2' IST-X " Side Trim Kit, beige paint, adaptable for ceilings up to 2' IST- " Side Trim Kit, white paint, adaptable for ceilings up to 2' IST-4 " Side Trim Kit, gray paint, adaptable for ceilings up to 2' Other Optional Accessories Model #: AHCK-2 SK SK Description: Anti-Huffing Refrigerant Caps (Quantity 2) with Key Hard Start Kit for -Phase Models (I30A-A, I3A-A & I42A-A) Only Hard Start Kit for -Phase Models (I4A-A & IA-A) Only Form No S344-97 Supersedes S344-7 Page 3 of 22

Top View 3 " 4 2 4 " 24" 2 4 " Front View (2) 2"x24"x30" Filters Return Air Control Panel (2) Washable Vent Intake Air Filters (2) 2" x 20" Air Filters Vent Exhaust " 4 4 5 47 " Total Width " With Sides Removed 20" 20" x 24" Supply Frame 3 2 4 " 3 3 " Total Depth Low Voltage 2" High Voltage Entrance 7 " Entrance Electric Heat Wire Channel (4) Lift-Off Hinges Locking Door Latch Electrical Disconnect 94" Total Height 5" 7 3 4 " Upper Section Locking Door Latch 4 3 " 5 5 " 22 4 " Lower Section Front Forklift Holes (Remove Front Trim) Side Forklift Holes (Remove Sides) Right Side View 30" With Doors and Sides Removed Unit Specification Sheet (2) Return Openings Outer Sleeve Supply Air Back View Return Air Return Air Inner Sleeve Outer Sleeve Inner Sleeve 2 " 7 (2) Side Handles 24 2 " (2) Unit Drains (2) Opt. Unit Drain Entrances " 3 3 4 " " 3 3 " MIS-297 A Form No S344-97 Supersedes S344-7 Page 4 of 22

WING WALL CONSTRUCTION TOP VIEW DRAIN ACCESS 4" REMOVABLE SIDES 2" MIN. 2" MIN. 2 2 CLOSET CONSTRUCTION TOP VIEW DRAIN ACCESS DRAIN ACCESS AREA 4" 2" MIN. 2 2" MIN. 2" MIN. 4" MIN. LEFT CORNER CONSTRUCTION TOP VIEW 2" MIN. 2 DRAIN ACCESS 3 3/" 2" MIN. FOR LEFT SIDE ACCESS DRAIN ACCESS DETAIL VIEW FROM BACK OF UNIT RECOMMENDED SERVICE ACCESS DIMENSIONS 4" DRAIN ACCESS 2" MIN. FOR RIGHT SIDE ACCESS 4" FILTERS 24" MIN. 24" MIN. REMOVABLE SIDES 4" 0" REQUIRED 2" RECOMMENDED RIGHT CORNER CONSTRUCTION TOP VIEW DRAIN ACCESS 4" MIN. FOR FILTER ACCESS ALL FILTER AND COMPONENT ACCESS IS FROM THE FRONT. COILS CAN BE CLEANED FROM THE FRONT, BUT SIDES ARE EASILY REMOVED FOR ENHANCED ACCESS. 0" REQUIRED 2" RECOMMENDED 2 2" MINIMUM DIMENSIONS ARE REQUIRED FOR UNIT OPERATION. IT IS STRONGLY RECOMMENDED TO USE 20" MINIMUM DISTANCES IF POSSIBLE FOR EASE OF UNIT SERVICEABILITY MIS-3273 A Form No S344-97 Supersedes S344-7 Page 5 of 22

RISER KIT DIM A DIM B DIM C NONE 3"-34" MAX 29 7/32" 94 /" IRP-3 (3") 34"-37" MAX 32 7/32" 97 /" IRP- (") 37"-40" MAX 7/32" 0 /" Optional Duct Wall Section View Ceiling Optional Trim or Supply Duct Box Unit Outside Wall Telescoping Wall Sleeve** Grille Outside Wall Optional Top Bracket (4) optional Unit Mounting holes Sleeve Mounting Hole Locations Opening Centered on (4) optional Unit Mounting holes 20 7 " Centered 43 3 " 4" Min. 4-/2" Max. 7 " 20 Centered 42-3/4" Min. 43-/4" Max. 20" 20" " 49 3 " 2 5 3" DIM C " Floor 3" Min. 34" Max. * DIM A * 5 " C L " 20" 20 7 " 43 7 " 20" " Room Floor Level C L 4 " DIM B 3/4 Right Side View 7 3/ * Higher Sill Heights Acheivable With Base Kit. ** Separate telescoping sleeves available for different wall thicknesses. " 7.5" Front (Wall Only) View FLOOR MOUNTING HOLE & CENTERLINES MIS-29 D Form No S344-97 Supersedes S344-7 Page of 22

IPBDF, IPBDFH2 AND IPBDFH IPBDF, DUCT-FREE IPBDF2 PLENUM AND IPBDF BOX DUCT-FREE DIMENSIONS PLENUM BOX DIMENSIONS ROUTE LOW VOLTAGE UNIT POWER THROUGH BOX IN CONDUIT A ROUTE HIGH VOLTAGE UNIT POWER THROUGH BOX IN CONDUIT B 94" 7' - " DIMENSIONAL CHART MODEL NO. DIM. A DIM. B IPBDF DIMENSIONAL " 2" CHART ('-") IPBDF2 MODEL NO. 2" DIM. A" ('-") DIM. B IPBDF IPBDF " " 2" (9'-4") 2" ('-") IPBDFH2 2" " ('-") IPBDFH " 2" (9'-4") MIS-3057 C Form No S344-97 Supersedes S344-7 Page 7 of 22

TOP VIEW VALVE WIRING ENTRANCE 4 /2" 2" 2" 7 3/4" 3/" IPBDF2HW DUCT-FREE HOT WATER COIL DIMENSIONS Ø7/" O.D. WATER CONNECTIONS. NOT DESIGNATED AS "IN" OR "OUT". CAN BE PIPED AS NEEDED FOR EASE OF VALVE INSTALLATION AND SUPPLY/RETURN CONNECTIONS. ROUTE LOW VOLTAGE UNIT POWER THROUGH BOX IN CONDUIT 2" 2" ROUTE HIGH VOLTAGE UNIT POWER THROUGH BOX IN CONDUIT HIGH VOLTAGE POWER ENTRANCE " ' - " 94" 7' - " MIS-3059 Form No S344-97 Supersedes S344-7 Page of 22

TOP VIEW 9 7/" 29 7/" /4" IHWC DUCTED HOT WATER COIL DIMENSIONS 23 7/" SUPPLY OPENING 9 7/" 24 3/4" 9 3/4" 2" LOW VOLTAGE ENTRANCE 40 7/" Ø7/" O.D. WATER CONNECTIONS. NOT DESIGNATED AS "IN" OR "OUT". CAN BE PIPED AS NEEDED FOR EASE OF VALVE INSTALLATION AND SUPPLY/RETURN CONNECTIONS. " ROUTE HIGH VOLTAGE UNIT POWER THROUGH BOX IN CONDUIT 2.5" HIGH VOLTAGE POWER ENTRANCE 5" ' - 9" 94" 7' - " MIS-305 Form No S344-97 Supersedes S344-7 Page 9 of 22

Dehumidification Performance Data I30AD APPLICATION PERFORMANCE DATA Outdoor System Capacity Pounds of Water/Hour Evaporator Airflow Approximate Supply Air DB/WB %RH DB Total Sensible Latent S/T Lbs. CFM DB WB 5/3 90 5 3,375 3,550 7,25 43.2%. 50 50.7 50.3 A/C Mode A/C vs. Dehum 5/3 90 5 5,025 (,50),75 N/A 5.3 50.3 57.3 Dehum 75/2.5 50 75 2,25 2,0,525 7.%.2 50 52.0 5.0 A/C 75/2.5 50 75,900 3,50 5,250 N/A 5.0 50 7. 5.9 Dehum 75/5.5 75 30,700 9,250,450 2.7%. 50 54.5 53.5 A/C 75/5.5 75,400,775 9,25 N/A 9. 50 73..4 Dehum 75/ 70 75 32,0,725 5,375 52.% 4.5 50 57. 5.2 A/C 75/ 70 75 3,50 (0) 3,250 N/A 2.5 50 75. 3. Dehum 0/7 50 95 27,575 20,375 7,200 73.9%. 50 5. 5.7 A/C 0/7 50 95 2,25 (2,975) 5,0 N/A 5.3 50 3.3.0 Dehum I3AD APPLICATION PERFORMANCE DATA Outdoor System Capacity Pounds of Water/Hour Evaporator Airflow Approximate Supply Air DB/WB %RH DB Total Sensible Latent S/T Lbs. CFM DB WB 5/3 90 5 39,550,550 23,000 4.% 2.7 50 5.7 5.2 A/C Mode A/C vs. Dehum 5/3 90 5 7,950 (925),75 N/A 7. 50 5.7 57.9 Dehum 75/2.5 50 75 3,775 27,750 9,025 75.5.5 50 52. 5.3 A/C 75/2.5 50 75,000 5,025 5,975 45.7% 5. 50 70.9 59.3 Dehum 75/5.5 75 39,75 24,75 5,500.9% 4. 50 55. 54.3 A/C 75/5.5 75 3,000 3,075 9,925 23.7% 9.4 50 72.5 2.0 Dehum 75/ 70 75 4,25 2,300 20,325 5.2% 9.2 50 57.9 5. A/C 75/ 70 75 5,900,050 4,50.% 4.0 50 74. 4.0 Dehum 0/7 50 95 34,225 25,25,0 74.9%. 50 59.3 57.5 A/C 0/7 50 95 7,25 2,575 5,050 33.% 4. 50 2..7 Dehum I42AD APPLICATION PERFORMANCE DATA Outdoor System Capacity Pounds of Water/Hour Evaporator Airflow Approximate Supply Air DB/WB %RH DB Total Sensible Latent S/T Lbs. CFM DB WB 5/3 90 5 47,475,75 2,0 39.% 27.0 300 52.0 5.5 A/C Mode A/C vs. Dehum 5/3 90 5 20,75 (,925) 22,0 N/A 20. 300.3 5.2 Dehum 75/2.5 50 75 42,775 3,75,0 74.%.5 300 52.7 5.0 A/C 75/2.5 50 75,950 5,075,75 42.5%.5 300 7.3 59.5 Dehum 75/5.5 75 45,750 27,750,000.7% 7.0 300 55.4 54.0 A/C 75/5.5 75 5,325 2,25 2,700 7.% 2.0 300 73. 2.0 Dehum 75/ 70 75 4,075 24,300 23,775 50.5% 22.4 300 57. 5.7 A/C 75/ 70 75 7,75 250 7,425.4%.4 300 74. 4.2 Dehum 0/7 50 95 40,375 29,575,00 73.3%.2 300 59.2 57.2 A/C 0/7 50 95 325 (3,900) 4,225 N/A 4.0 300 2.. Dehum I4AD APPLICATION PERFORMANCE DATA Outdoor System Capacity Pounds of Water/Hour Evaporator Airflow Approximate Supply Air DB/WB %RH DB Total Sensible Latent S/T Lbs. CFM DB WB 5/3 90 5 53,525 22,500 3,025 42.0% 29.3 550 5. 50. A/C Mode A/C vs. Dehum 5/3 90 5 20,575 (4,925) 25,500 N/A 24. 550.0 5. Dehum 75/2.5 50 75 50,0 3,25 2,225 75.7%.5 550 5.5 50.5 A/C 75/2.5 50 75 2,00 3,575 9,225 N/A.7 550 72.7 59.7 Dehum 75/5.5 75 53,750 32,975 20,775.3% 9. 550 54. 53.7 A/C 75/5.5 75 5,25 50 4,975 N/A 4. 550 74.4 2.3 Dehum 75/ 70 75 55,0 2,750 2,50 5.7% 25.3 550 57.2 5.4 A/C 75/ 70 75 7,500 (,75) 9,375 N/A.3 550 7. 4.7 Dehum 0/7 50 95 49,250 3,0 2,900 73.% 2.2 550 57. 5.4 A/C 0/7 50 95 (50) (7,300),450 N/A. 550 4. 7.2 Dehum IAD APPLICATION PERFORMANCE DATA Outdoor System Capacity Pounds of Water/Hour Evaporator Airflow Approximate Supply Air DB/WB %RH DB Total Sensible Latent S/T Lbs. CFM DB WB 5/3 90 5,000 25,925,075 42.5% 33. 750 5.4 50. A/C Mode A/C vs. Dehum 5/3 90 5,325 (,475) 24,00 N/A 23.4 750. 59. Dehum 75/2.5 50 75 5,425 44,475 3,950 7.% 3.2 750 52. 50. A/C 75/2.5 50 75 9,0 525,575 N/A. 750 74.. Dehum 75/5.5 75 2,000 3,25 23,375 2.3% 22. 750 55.0 53.9 A/C 75/5.5 75 2,50 (,700) 3,50 N/A 3. 750 7.0 3.4 Dehum 75/ 70 75 5,50 33,550 3,0 5.5% 29. 750 57. 5.5 A/C 75/ 70 75 4,950 (4,575) 9,525 N/A.4 750 77.4 5.5 Dehum 0/7 50 95 5,450 42,050 4,400 74.5% 3. 750 5. 5.7 A/C 0/7 50 95 (3,750) (,550),00 N/A.4 750 5. 7.5 Dehum Form No S344-97 Supersedes S344-7 Page 20 of 22

I30A-IA Sound Data at Feet. dba @ feet, Values recorded in Bard Manufacturing Company, Inc. Sound Lab Facility. 2. Actual field results may vary with classroom design and construction. 3. Integrated values calculated per ANSI/ASA S2.-2009 / Part 2, Section 5.2.2., Table 2 Triple Mode Type 3 HVAC System Duty Cycles: Ventilation 5%, Part Load 25%, Full Load 7% 4. Integrated Sound Values are also applicable for use in learning spaces for CHPS and LEED Schools: EQ Prerequisite 3 - Minimum Acoustical Performance, OPTION. Using methods prescribed in ANSI S2., classrooms must achieve a maximum background noise level of 45 dba. Vent: ERV IPBDFH-2 Duct Free 2" Plenum Box Ducted Model Operation ERV Off ERV @ 50 ERV @ 375 ERV @ 450 ERV Off ERV @ 50 ERV @ 375 ERV @ 450 I30A Integrated 33.7 34.0 39.3 40.0 33. 34.0 39.0 40. I3A Integrated 37.7 3.0 40.7 4.7 3.5 37. 4.7 42.7 I42A Integrated 3. 40.7 4.3 4.9 39.4 39.3 4. 42.4 I4A Integrated 39.0 39.0 39.7 39. 39. 39. 40.3 40. IA Integrated 4.4 4.3 4. 4. 4.3 4.3 4. 4.9 Vent: CRV IPBDFH-2 Duct Free 2" Plenum Box Ducted Model Operation CRV Off CRV @ 300 Factory Setting(s) shaded in Gray CRV @ 375 CRV @ 450 CRV @ 525 CRV Off CRV @ 300 CRV @ 375 CRV @ 450 I30A Integrated 34.4 3.0 3.2 40. 42. 34. 3. 3. 40. 42.0 I3A Integrated 37.0 3.5 40.3 42.4 43.9 37.2 40.2 39.2 42.2 44.0 I42A Integrated 39.2 39. 4.0 42.5 43.5 39.9 40.4 4. 42. 43.5 I4A Integrated 40.2 40.7 4.5 43.0 44.2 4.0 40.7 42.2 43.4 44. IA Integrated 44.0 44.3 44. 45.4 45.9 43.5 43.7 44. 44. 45.5 CRV @ 525 Outdoor Sound Data at Feet I30A I3A I42A I4A IA Model 3.7. 7.3 7.9 7. Form No S344-97 Supersedes S344-7 Page 2 of 22

I-TEC 2-Stage Air Source Air Conditioners Model Number Nomenclature I 3 A D A 0Z R P 4 X X 2 Model Series Nominal Capacity: 30 = 30,000 BTUH 3 = 3,000 42 = 42,000 4 = 4,000 =,000 System Type: A = Air Conditioner Controls: X = 24v terminal block Only w/o CompleteStat = CompleteStat THO (Temp, Humidity & Occupancy) 2 = CompleteStat THO w/co2 3 = CompleteStat THO w/ Ethernet 4 = CompleteStat THO w/co2 & Ethernet Note: CompleteStat must be field installed & wired. All units have 24V terminal block. See Selection Guide. Revision Level D = Dehumidification Electrical Rating: A = 230/20, - B = 230/20, -3 C = 4--3 Coil Treatment: X = Std. Hydrophilic Fin Evap. & Uncoated Alum. Cond. Coil = Phenolic Coated ID coil 2 = Phenolic Coated OD coil 3 = Phenolic Coated ID & OD coil Electric Heat: 0Z = No heat w/breaker 04 = 4KW -Phase 05 = 5KW -Phase 0 = KW 3-Phase 09 = 9KW 3-Phase = KW -Phase 5 = 5KW & 3-Phase = KW 3-Phase 20 = 20KW -Phase Vent Option: B = Blank Off Plate M = Multi-Speed CRV N = Multi-Speed CRV with Economizer Mode Q = Modulating CRV (0-Vdc) R = ERV Filter: P = 2 inch pleated MERV M = 2 inch pleated MERV N = 2 inch pleated MERV 3 Door Vinyl Graphics Options X = No Graphics A = Stacked Books (Color Code - White Only) B = Paint Brush (Color Code - White Only) Color: X = Beige, Painted Steel = White, Painted Steel 4 = Gray, Painted Steel CompleteStat Selection Guide Vent Type None CRV ERV Type of Vent Control BACnet Communication Ethernet Connection Control Code Description CompleteStat Part Number N/A Yes No CompleteStat THO (Temp, Humidity & Occupancy) CS9B-THO N/A Yes Yes 3 CompleteStat THO w/ethernet CS9BE-THO On/Off Yes No CompleteStat THO (Temp, Humidity & Occupancy) CS9B-THO Demand Yes No 2 CompleteStat THO w/co2 CS9B-THOC On/Off Yes Yes 3 CompleteStat THO w/ethernet CS9BE-THO Demand Yes Yes 4 CompleteStat THO w/co2 & Ethernet CS9BE-THOC On/Off Yes No CompleteStat THO (Temp, Humidity & Occupancy) CS9B-THO Demand Yes No 2 CompleteStat THO w/co2 CS9B-THOC On/Off Yes Yes 3 CompleteStat THO w/ethernet CS9BE-THO Demand Yes Yes 4 CompleteStat THO w/co2 & Ethernet CS9BE-THOC BACnet is standard - all versions, shielded twisted pair. These models also have CAT 5 port for ease of networking in addition to twisted pair terminals. Demand control for ventilation is ON/OFF based on CO2 set-point. If modulating mode for ERV is required, use THO controller plus 403-07 CO2 controller with modulating output. Form No S344-97 Supersedes S344-7 Page 22 of 22 Bard Manufacturing Company, Inc. Bryan, Ohio 40 www.bardhvac.com Due to our continuous product improvement policy, all specifications subject to change without notice. Before purchasing this appliance, read important energy cost and efficiency information available from your retailer. Form No. S344 September 207 Supersedes: S344-7