The Guide To Serving Filtrine ater In Hospitals and Healthcare Facilities New Construction or Renovation CHILLER/PURIFIERS MULTIPLE OUTLET UNITS... 2 SINGLE OUTLET UNITS... 4 SERVING FIXTURES FILLING STATIONS... 5 VANDAL PROOF MODELS... 6 LEAD FREE All FILTRINE products certified to be compliant with CA-AB1953 and NSF 61, Annex G LABOR & PARTS HOSP GUIDE-1
Recirculating Chiller/Purifiers For Ice Makers and Multiple Drinking ater Outlets TYPICAL FREE STANDING CHILLER/PURIFIER TASTEMASTER PURIFIER ATER TASTE & PURITY Removes particulates, organic tastes /odors, chlorine taste/odor and water-borne pathogens EXTRA-HEAVY CONSTRUCTION FDA FOOD GRADE polypropylene inner body encased in a stainless steel housing EASY MAINTENANCE Easy-to-replace purifier element - use housing wrench [supplied] and the job is done in a minute EXCLUSIVE DUAL-SEAL Insures maximum performance for the life of the element LEAD REDUCTION ELEMENT AVAILABLE Removes lead, particulates, organic tastes/ odors, chlorine taste /odor and water-borne pathogens... consult factory for specifications PRE-CHILL and SAVE ENERGY Filtrine s Pre-Chiller/Purifier is able to serve constant 50 F chilled water because, unlike conventional chillers an ES Pre-Chiller/ Purifier employs a large energy- saving, insulated reservoir. This allows the unit to build a reserve of chilled water during low usage periods to fill personal water containers and handle the peak demands of ice-making, lunch hours, coffee breaks, etc. and still meet the low average draw. A single free-standing unit uses less energy than multiple EC s serving a comparable population. FEATURES ENERGY-SAVINGS Designed for low installation and operating cost - exclusive immersion coil evaporator is most energy-efficent type available 15% MORE ICE Pre-chilled source water for ice-makers can increase production up to 15% PURIFIED/CHILLED ATER FOR ICE AND DRINKING One unit can serve both ice maker and multiple drinking water fixtures COMPACT FOOTPRINT Uses little floor space... wall mount available ULTIMATE SECURITY Locate in locked mechanical room - the sealed re-circulating loop prevents tampering or accidental contamination QUIET OPERATION Engineered for indoor operating environment EASY SERVICING Designed for low installation and operating costs... access panels removeable with out tools 2 LEAD MANUFACTURED FILTRINE IS ISO 9001-2008 REGISTERED PRODUCT LINE APPROVED MARK AVAILABLE LIFETIME LT ARRANTY I T H O U T L E A D
FREE-STANDING CHILLER/PURIFIERS FOR ICE MACHINES and DRINKING ATER READY-TO-ISSUE SPECIFICATION: In order to provide 50OF purified drinking water to potable water outlets as shown on plan, contractor shall furnish Free-Standing Chiller/Purifier Unit To Include: Hermetic compressor 115/60/1 with condenser, thermostat, expansion valve, sight glass and dehydrator. Cooling tank #304 stainless steel, insulated with closed cell thermoelastomer with stainless steel immersion coil evaporator. Purifier to remove sediment particles, chemicals such as chlorine, organic tastes and odors. Stainless steel pump to circulate 50OF water to all outlets. All contained in a free-standing rustproof, enameled steel cabinet with key-latched grille for ventilation and service access. No hinge or screws shall be visible on front of the mounted unit. Chiller/Purifier Shall Be: ES- [ ] -RFC-FS CHILLER/PURIFIER as manufactured in USA with USA parts and labor by Filtrine Manufacturing Company Keene, NH and shall include Lifetime arranty. ES-RFC-FS CHILLER/PURIFIER DATA FOR RECIRCULATING MODELS PIPING FILTRINE PERSONS ALLOANCE - COMP MODEL No. SERVED TANK CIRC 115/60/1 PURIFIER ENCLOSURE ATER TOTAL LOOP MOTOR * hp gal PUMP CAPACITY SUPPLY DIMENSIONS CONN hp gph POER PRE- TASTE inches inches ft ips ** FILTER MASTER D H IN/OUT ES-2-RFC-FS 100 100 1/2 1/5 2 1/50 8 FLA 6 N.A. TM1-0.5 42 10 26 ES-4-RFC-FS 200 200 1/2 1/4 4 1/50 12 FLA 7 PF4 TM1-0.5 36 16 26 1/2 ES-6-RFC-FS 300 300 1/2 1/3 6 1/50 16 FLA 9 PF4 TM1-0.5 46 16 26 ES-8-RFC-FS 400 400 1/2 1/2 8 1/50 20 FLA 12 PF4 TM1-0.5 52 16 32 * Assume 1 qt. [0.9L] per day per person in typical usage. Capacities based on 80 F [27 C] inlet, 50 F [10 C] outlet. ES models include extra capacity to handle heat loss of insulated piping in the circulating loop up to the length shown. hen piping runs exceed allowance shown, reduce population served by 25 people per 50 feet of additional piping. ** Other voltages available... consult factory. TYPICAL FREE-STANDING CHILLER/PURIFIER SCHEMATIC ITH KEY LOCK LATCH HINGED DOOR IN PLACE LEFT END VIE ATER HOOKUPS F R O NT H ELECT GROUNDED ELECT. D END VIE 1/8" 2-3/4" ALL MTG BRACKET - OPTIONAL IDTH VARIES 3/4" 1"@ BOTH ENDS ALL HOLES 5/16" DIA. 1/4" EXAMPLE OF FREE-STANDING CHILLER/PURIFIER FLOOR PLAN Purified/Chilled ater Distributed through Plenum Delivery Loop LEGEND 1...ICE MACHINE 2... FILLING STATION 3...COFFEE MACHINE 4... FILLING STATION, DRINKING FOUNTAIN COMBO 1 2 3 Nurses Station Pre-Chiller/Purifier Visitor Lounge 4 Rest 2 HOSPITAL ING 2 Rest Break 3 3
Cabinet Insert Chillers Serve Single Outlets FOR CUSTOM CABINETS AND COUNTERS Filtrine Cabinet Insert s [CIA] are a versatile tool for designers and kitchen-equipment manufacturers offering packaged chilled water with any custom cabinet. CIA models also provide space-saving, concealed, in-wall water cooling for cafeterias and food service areas in schools, colleges, offices, etc. These chillers are available with air or water-cooled condenser. They are ready for fast installation and plug-in operation. TYPICAL CABINET INSERT Chiller Shown without enclosure CABINET INSERT CHILLERS PROVIDE CHILLED ATER IN ANY CUSTOM CABINET Compact chilling unit fits into custom cabinet to provide cool water IN-COUNTER INSTALLATION Can be mounted in-counter to provide cool water as part of serving counter SPACE-SAVING, CONCEALED, IN-ALL COOLING Can be mounted in-wall, without protruding into room, to provide chilled water to individual outlets READY-TO-ISSUE GUIDE SPECIFICATION Supply and install where shown on plans factory packaged cooling unit. Chiller to have a minimum storage capacity of [ ] gals. with recovery of [ ] GPH cooling from 80 to 50 F in a 90 ambient. Condensing unit to be [ ] hp., hermetic compressor wired for 115/60/1 with oversized [air] [water]- cooled condenser, and provided with adjustable thermostat, filter dehydrator and 6 electrical cord. Cooling tank of #304 stainless steel, tested at 250# insulated and enclosed in a rust proofed steel container. Chiller to be model M- [ ] CIA chiller as manufactured in the USA by Filtrine Mfg Co, Keene, NH. OPTIONAL GRILLE - See chart below for dimensions Hinged access grille with key lock, louvered section to be 50% open. [Condenser of chiller should be located within one inch of grille.] OPTIONAL TASTEMASTER PURIFIER hen hinged access grille is installed, a TM1-0.5 TasteMaster Purifier [removes sediment, organic tastes and odors and chlorine and cysts] may be specified. MODEL NUMBER* GAL STORAGE CABINET INSERT CHILLER SELECTION CHART CAPACITY 80-50 O F Chiller SHIPPING GRILLE COND. 1 HOUR PEAK 2 HOUR PEAK DIMENSIONS** EIGHT DIMENSIONS HP LBS GAL PERSONS GAL PERSONS D H H M-2-CIA 2 8 96 12 176 1/5 23" 7" 20" 70 M-4-CIA 4 12 192 20 352 1/4 23" 11" 24" 80 M-6-CIA 6 18 288 27 432 1/3 23" 12" 24" 85 4 26" 26" M-10-CIA 8 29 464 51 816 1/2 26" 16" 26" 160 30" 30" M-18-CIA 10 30 800 88 1408 3/4 39" 16" 26" 375 42" 30" * ater cooled condensers available - use suffix CI. ** Dimensions based on 120 or 230/60/1 - For other voltages/phases/hertz... consult factory.
Filling Stations Are The Sustainable Answer To Throw-Away Bottles C ONCERNS ABOUT BOTTLED ATER INCLUDE MONEY ASTED by government and business, billions of bottles tossed in landfills each year, enough water bottle litter to encircle the earth five times, millions of barrels of oil used to manufacture disposable bottles, acres of floorspace taken over by bottle water storage, energy consumed in distribution, etc. The bottled water industry has convinced water drinkers that somehow tapwater is inferior to bottled. Most municipalities provide pure, clean water of verified quality at a fraction the cost of bottled water. FILTRINE IS LEADING THE EFFORT to create "No Throw Zones" in government, residential, healthcare, educational, business and manufacturing facilities. ater drinkers provide a personal, reusable water container to be re-filled using a FILLING STATION. N O T H R O Z O N E FEATURES All stainless steel construction Most models fit in 4" wall Choice of finish options No plastic parts No electricity [models without chiller] Flush mount "Soft Touch" filler valve Cup dispenser/disposal options Vandal-Resistant options FILLING STATIONS ARE AVAILABLE IN A RANGE OF IN-ALL CONFIGURATIONS... OR DESIGN YOUR ON Satin Stainless B-103 BASIC IN-ALL FILLER B-103-107-16 IN-ALL FILLER ITH NON- RECESSED DRINKING FOUNTAIN FILLING STATIONS ARE AVAILABLE IN A RANGE OF DECORATOR FINISHES... OR SPECIFY YOUR ON 5 Mirror Stainless Satin Bronze B-103-CD2 IN-ALL FILLER ITH DUAL CUP DISPENSERS and DISPOSAL Mirror Bronze B-103-CD4 IN-ALL FILLER ITH QUAD CUP DISPENSERS and DISPOSAL Statuary Bronze
Vandal Proof Drinking Fountain with Purifier 90MOD-VP-TM 90MOD-VP-TM Non-Recessed DrinkingFountain with TasteMaster Purifier FEATURES Built-in TasteMaster Purifier removes cysts, organic tastes /odors, chlorine taste/odor and sediment... Lead Reduction element available. Heavy-duty 14 gauge stainless steel construction throughout - virtually indestructible Vandal proof bubbler welded to deck of fountain Vandal proof flush-mounted Soft Touch valve Vandal proof drain and strainer, stamped into bowl Vandal proof hinged plate with key lock on bottom of unit provides access to trap and flow regulator and TasteMaster Purifier Extra heavy wall mounting plate with 3/8 steel support arms, designed to withstand 500lb vertical force For surface mounting, matching cover plate is available Covered by LIFETIME ARRANTY MANUFACTURED LEAD I T H O U T L E A D IN COMPLIANCE ITH CALIFORNIA AB 1953 LIFETIME LT ARRANTY FILTRINE IS ISO 9001-2008 REGISTERED PRODUCT LINE APPROVED MARK AVAILABLE SPECIFICATIONS FOUNTAIN - 14 gauge Stainless Steel Bronze Finish #4 Satin #8 Mirror Statuary Bronze COVER PLATE - 14 gauge Stainless Steel Bronze Finish #4 Satin #8 Mirror Statuary Bronze BUBBLER TYPE - Vandal Proof Separate SOFT TOUCH valve BUBBLER FINISH STAINLESS STEEL - Default #8 Mirror Finish BRONZE #8 Mirror Finish - Default #4 Satin Finish Statuary Finish BOTTLE FILLER - OPTIONAL Goose Neck - welded to fountain deck with separate SOFT TOUCH valve 90MOD- VP-TM Non-Recessed Drinking Fountain with Secure, Built-In Purifier "SOFT-TOUCH" PUSH BUTTON FOR GOOSENECK FILLER (OPTIONAL) TOP VIE 1/4" O.D. SUPPLY 12-5/8" 1-1/4" O.D. DRAIN GOOSENECK FILLER (OPTIONAL) LOCK-ON BUBBLER 3" "SOFT-TOUCH" PUSH BUTTON FOR BUBBLER 18" HINGED, KEY LOCK ACCESS PLATE ON BOTTOM OF FOUNTAIN SIDE VIE GOOSENECK FILLER (OPTIONAL) COVER PLATE 11" 5-1/2" 5-1/2" P-TRAP ITH CLEANOUT 1-3/4" TASTEMASTER PURIFIER FINISHED ALL MOUNTING PLATE 1" 3" 1" 6-3/8" 1/4" STEEL MOUNTING PLATE SIDE VIE 3/8 MOUNTING HOLES 3" 15-1/2" 6-3/8" 14-1/2" ARMS ELDED TO MOUNTING PLATE 1/4 STEEL CARRIER ARMS TESTED TO ITHSTAND 500 LB VERTICAL IMPACT STAINLESS STEEL COVER PLATE CUTOUT FOR PLUMBING CONN CUTOUT FOR CARRIER ARMS 8 6" 16 8 2-3/8 1-3/4 15 6
B103-C2-STFV-MOD FILLING STATION ith Maximum Security Features A MODEL OF SAFETY AND SECURITY, this FILLING STATION is the ONLY drinking water dispenser approved by the New York State Office of Mental Health (NYS-OMH) to be in compliance with their PATIENT SAFETY STANDARDS for High Risk areas B103-C2-STFV-MOD Schematic TOP VIE ATER IN 3/8 FPT CUTOUT FOR ATER CONN. CUP DISPENSER SOCKET-TYPE MOUNTING PREVENTS REMOVAL UNLESS DOOR IS OPEN 10" 12-1/2" 45 O SLANT ON TOP LIP w/coverplate KEY LOCK FOR SECURITY SIDE VIE LEFT END 1-1/4" HINGED COVERPLATE OPENS LEFT PAPER CUP DISPENSERS 100 cup cap. total (6 or 8 oz cups) FLUSH MOUNT FILLER FOR CUPS, PERSONAL ATER CONTAINERS AND CARAFES 1-1/4" TYPICAL 9" 17" 12" 34" ELDED STEEL PLATE ITH HOLES FOR CUP DISPENSING BLOCKS ACCESS TO INSIDE OF UNIT USE DIMPLE TYPE CUP RETENTION 4" 3/16 MOUNTING HOLES FOR SCRES [BY OTHERS] NOTE: SOFT TOUCH PUSH BUTTON IS ACTIVATED THROUGH HOLE IN COVER PLATE NO PARTS ARE USER ACCESSIBLE SCRES IN DRAIN GRILLE PERFORATED DRAIN PAN FASTENED ITH TAMPER-PROOF SCRES 12-1/2" 5" DRAIN 1-1/4 O.D. [SLIP-FIT COUPLING FURNISHED LOOSED] 3-1/2" 1-1/8" ALL OPENING 10-1/2 x 4 D x 32 H MANUFACTURED LEAD I T H O U T L E A D IN COMPLIANCE ITH CALIFORNIA AB 1953 LIFETIME LT ARRANTY FILTRINE IS ISO 9001-2008 REGISTERED PRODUCT LINE APPROVED MARK AVAILABLE 7