91-00-01-01 Section B Field Instruments Contents Product Type Literature No. Overview 30-00-02-01 34 ST 3000 Series 100e Smart Pressure s SMV 3000 Smart Multivariable Model STM125 Series 100e Models Series 100e Models Series 100e Gauge Pressure Models Series 100e Gauge Pressure for High Temperature Models Series 100e Flange-Mounted Liquid Level Models Series 100e Remote Diaphragm Seal Models ST 3000 Series 900 Smart Pressure Series 900 Models Series 900 Models Series 900 Gauge Pressure Models Series 900 Flange Mounted Liquid Level Models Series 900 Differential and Gauge Pressures with Remote Diaphragm Seals ST 3000 Smart Series 900 Flush Mount Model STG93P Related Offerings ST 3000 Series 100 Models Overview SFC Smart Field Communicator Model STS103 34-SM-03-01 34-ST-03-60 34-ST-03-61 34-ST-03-62 34-ST-03-70 34-ST-03-63 34-ST-03-65 34-ST-03-66 34-ST-03-67 34-ST-03-68 34-ST-03-57 34-ST-03-73 34-ST-03-72 34-ST-03-55 3-A Sanitary Flange Mount and Sanitary Remote Seal Models 34-ST-03-26 Integral Orifice Assembly to Measure Small Flow Rates SCT 3000 Smartline Configuration Toolkit MVA Multi-Variable Analog Interface for Smart s MVA-111 Single Variable Analog Interface for Smart s MTS Multi-Variable Trip Switch for Smartline s DEM-PLC/SLC Platform Support RMA 3000 Model Selection Guide SFC Smart Field Communicator STS103 Model Selection Guide 34-ST-03-33 34-CT-03-02 34-MV-03-01 34-MV-03-03 34-MV-03-02 34-MV-03-04 34-ST-16-46 34-ST-16-08
91-00-01-01 Product Type 34 STT 3000 Smart Temperature (cont.) STT 3000 Model STT350 and STT35F Smart Temperature STT250 Smart Temperature Specification and Model Selection Guide Housing Specification for STT250 Temperature Sensor Specification for STT250 (non-north America) Guide to Temperature Sensors and Thermowells for STT 3000 Smart Temperature s and SMV 3000 Smart Multivariable s STT 3000 Supplementary Accessories and Kits SCM 3000 PLUS Smart Coriolis Mass Flowmeter SCM 3000 PLUS Smart Coriolis Mass Flowmeter Specification and Application Data 36 MagneW 3000 PLUS Smart Electromagnetic Flowmeter MagneW 3000 PLUS Smart Electromagnetic Flowmeter Specification and Application Guide 37 SVM 3000 PLUS Smart Vortex Flowmeter SVM 3000 PLUS Smart Vortex Flowmeter Specification and Application Data Literature No. EN0I-5222 EN0I-6031 EN0I-6032 EN0I-6033 34-44-29-01 13:STT-9,10 34-CM-29-02 36-KI-29-02 37-VM-29-01
1/99 Field Instruments Honeywell transmitters and transducers measure flow, temperature, pressure or liquid level, and provide electrical output signals. The output signals are proportional to the input and compatible with Honeywell s full line of indicators, recorders, and controllers. A decision tree is provided on page B-4 for the rapid selection of a general transmitter or transducer category, based on given input and output requirements. Refer to the Specification or Model Selection Guide for specific model selection. Description Pressure ST 3000 Smart accurately measures a differential, gauge, or absolute process pressure and transmits an output signal proportional to the measured variable. The output signal is transmitted in either an analog 4-20 ma format or in digital format for communicating digitally with a Honeywell control system. The selection of the output in an analog or digital communications mode is made through the Smart Field Communicator (SFC) or PC-based Smartline Configuration Toolkit (SCT). The piezoresistive sensor combined with the microprocessor enhances accuracy by compensating the output signal for the effects of ambient temperature and static pressure changes. Typical process control applications include measuring the rate of flow of a fluid through a pipe, or measuring the level of a liquid in an open or closed tank. The ST 3000 Series 100e and 900 were designed as direct replacements for conventional analog transmitters. They use the existing transmitter signal lines for power, signal transmission, and communication. Communication through the SFC or SCT is what makes the ST 3000 unique, and provides the capabilities of remote transmitter adjustments and diagnostics. Using the communicator an operator can adjust and display pertinent operating information, rerange the transmitter without applied calibration pressures, initiate diagnostic tests, and read the input and output pressures all without leaving the control room. This coupled with the transmitter s wide span adjustment, means that the ST 3000 is extremely adaptable to a variety of applications, and it can easily be adjusted to meet changing requirements. Related Offerings To complement the ST 3000 Series 100e product line, these related offerings provide performance and application alternatives: Series 900: Complements the Series 100e with a lower cost, fully smart product with improved performance over a conventional analog transmitter. A local zero and span is optional. Digital (DE) Mode: Allows direct digital communications, with a Honeywell process control system, SFC, or SCT. Stainless Steel Housing Option: Lets you use smart transmitters for special applications such as offshore and harsh chemical environments. SMV 3000 Smart Multivariable extends our proven smart technology to the measurement of three separate process variables with the software functionality to calculate compensated mass or volumetric flowrate. The SMV 3000 utilizes piezoresistive sensor technology to measure both differential pressure and static pressure and a single electronics board to process either an RTD or Thermocouple for the temperature measurement. With these three measurements, the SMV 3000 performs dynamic flow compensation by calculating discharge coefficient, thermal expansion factor, and gas expansion factor so that flowrates can be measured more accurately. The SMV 3000 supports primary flow elements such as orifice, Venturi, nozzle, averaging pitot tube, V-Cone and Laminar Flow Element. The SMV 3000, coupled with the appropriate primary flow ele ment, is a cost-effective mass flowrate Overview solution for gases, steam, and liquids. The SCT 3000 Smart Configuration Toolkit is the primary means for configuring the SMV 3000. Communication protocol choices are 4-20 ma or DE digitally enhanced. In non-flow applications, use the MVA from Vektron to output more than one variable, such as pressure and temperature. SCM 3000 PLUS Smart Coriolis Mass Flowmeters measure the mass, the volumetric, or the solids flow rate as well as the density and temperature of the process fluid flowing through it. They offer the following features: Full range of meter diameters from 2 to 80 mm supporting flow ranges from 0 to 0.08 kg/min (0 to 0.18 lbs/min) through 0 to 3 tons/min (0 to 6600 lbs/min). Straight parallel measuring tubes make it easy to completely drain the detector for quick inspection and cleaning at shutdown. Compact design minimizes space requirements and reduces installa tion cost. Sealed carrier tube provides added security. Wetted parts in SS, Hastelloy C, or Titanium. High oscillating frequencies make the measuring system insensitive to extraneous vibrations. Offers both local configuration at the meter using easily accessible external optical pushbuttons or remote configuration via either RS485 or HART communications mode. Worldwide safety approvals. 3A sanitary certification. % solids measurement. Honeywell s microprocessor-based STT 3000 Smart Temperature s convert a primary sensor input into a 2-wire output signal either proportional to the measured variable or linearized to temperature. The output signal is transmitted in either an analog 4-20 ma format or in a digital format (DE) for communicating digitally with a Honeywell control system. This universal temperature input model readily
accepts signals from a wide variety of thermocouple, millivolt, or resistive sensors (RTDs). All configuration, operating, and communications functions are under the control of the STT 3000 s microprocessor and are implemented via the Smart Field Communicator (SFC) or PC-based Smartline Configuration Toolkit (SCT). The STT 3000 Smart Temperature is suitable as a direct replacement for any conventional temperature transmitter in use today. The STT 3000 memory contains the characteristics of most commonly used non-linear temperature sensors. All transmitter adjustments and diagnostic checks are performed via the SFC or SCT connected across the 4-20 ma wire along its route, thus allowing configuration and maintenance from locations remote from the transmitter itself. They offer the following features: Single model accepts a variety of primary sensor input signals providing applications flexibility and reductions in stocking requirements. Digital cold-junction compensation for accurate and reliable temperature measurement over a wide operating range. Suitable for high density mounting on a DIN rail or remote field mounting in an explosion-proof housing. Smart transmitter performance with local or remote interfacing enables significant manpower efficiency improvements in commissioning, start-up and ongoing maintenance. MagneW 3000 PLUS Magnetic Flowmeters operate on the principles of Faraday s Law. They offer the following features: high-frequency excitation that minimizes electrochemical noise, and digital filtering that maximizes the signal-to-noise ratio for an accuracy of 0.5% of rate externally removable electrodes that allow inspection and replacement without removing the detector from process piping molded reinforced teflon liner that prevents crimping and puckering internal grounding rings that protect the detector liner during installation and eliminate the need for external grounding cables when used with lined piping digital operator panel built-in counter and totalizer batch control with preset counter trip automatic dual-range switchover with reverse flow high and low alarm settings continuous self-diagnostics SVM 3000 PLUS Smart Vortex Flowmeter provides a direct volumetric measurement for liquids, gases, and steam. The effective, accurate SVM 3000 PLUS offers the advantages of low installation costs, low pressure loss, high long-term stability, and a broad measuring range. The design withstands pipeline vibration amplitudes of up to 1 g and 500 Hz frequency in all directions enabling highly accurate measurements delivers long periods of maintenance-free operation with only factory calibration because of its highly stable sensor ensures proper and safe process and instrument operation with instrument self-diagnostics supports single sensor for all nominal diameters, fluids, and process temperatures offers both local configuration at the meter using easily accessible external pushbuttons or remote configuration via either RS485 or HART communications mode. Decision Tree Measured Variable Output Description Specification Flow *ST 3000 available with HART. HART, Contact, or Pulse 34-ST-03-60, 65 with Remote Seals 34-ST-03-57, 64 34-ST-03-60, 65 with Remote Seals 34-ST-03-57, 64 SMV 3000 Smart Multivariable Flow MagneW 3000 PLUS Magnetic Flowmeters SCM 3000 PLUS Smart Coriolis Mass Flowmeter SVM 3000 PLUS Smart Vortex Flowmeter MagneW 3000 PLUS Magnetic Flowmeters 34-SM-03-01 36-KI-29-02 34-CM-29-02 37-VM-29-01 36-KI-29-02
Decision Tree (continued) Measured Variable Output Description Specification 34-ST-03-61, 66 with Remote Seals 34-ST-03-57, 64 Gauge Pressure 34-ST-03-62, 67 Flange Mounted Liquid Level 34-ST-03-63, 68 Gauge Pressure with Remote Seals 34-ST-03-57, 64 34-ST-03-60, 65 for High Temperature 34-ST-03-70 Flush Mount 34-ST-03-73 Flange Mounted Liquid Level 34-ST-03-63, 68 Liquid Level with Remote Seals for High Temperature 34-ST-03-60, 65 34-ST-03-57, 64 34-ST-03-70 Flush Mount 34-ST-03-73 34-ST-03-61, 66 Vacuum Gauge Pressure Flange Mounted Liquid Level 34-ST-03-62, 67 34-ST-03-60, 65 34-ST-03-63, 68 with Remote Seals 34-ST-03-57, 64 Temperature STT 3000 Smart Temperature EN0I-5222, EN0I-6031 *ST 3000 available with HART. or HART STT 3000 Smart Temperature EN0I-6031
Summary Specification Input Output Type Upper Range Limits Minimum Span Operative Overpressure and Static Pressure Overrange Reference Accuracy (% Span) Analog Mode Key Number Spec. Differential Pressure, Flow, Vacuum, Liquid Level or Gauge Pressure 10 inh2o 0.4 inh2o 50 psi 400 inh2o 1 inh2o 750 psi 0.075 STM125 34-SM-03-01 10 inh2o 3000 psi 0.1 STD924 34-ST-03-65 600 inh2o 25 inh2o 3000 psi 0.075 STD125 34-ST-03-60 100 psi 5 psi 3000 psi 3000 psi 100 psi 3000 psi 400 inh2o 10 inh2o 3000 psi 0.075 STD120 34-ST-03-60 2250 psi 0.1 STD110 0.075 STD130 0.1 STD930 0.15 STD170 0.2 STD974 0.2 STR12D 34-ST-03-60 34-ST-03-60 34-ST-03-65 34-ST-03-60 34-ST-03-65 with Remote Seal(s) 100 psi 5 psi 3000 psi 0.1 STR13D 750 psi 100 psi 25 inh2o 0.2 STR93D 34-ST-03-57 300 psi 15 psi 450 psi 0.1 STG15T 34-ST-03-70 Gauge Pressure 500 psi 3000 psi 5 psi 750 psi 0.075 20 psi 750 psi 0.1 STG140 STG14L STG94L STG944 34-ST-03-62 34-ST-03-67 34-ST-03-62 STG170 100 psi 4500 psi 0.15 34-ST-03-62 STG17L STG974 300 psi 4500 psi 0.2 34-ST-03-67 STG97L Gauge Pressure or Vacuum 6000 psi 100 psi 9000 psi 0.15 STG180 STG18L 500 psi 9000 psi 0.2 STG98L 34-ST-03-62 34-ST-03-67 Gauge Pressure with Remote Seal(s) 500 psi 5 psi 20 psi 750 psi 750 psi 0.1 STR14G 0.1 STR94G 4500 psi 3000 psi 100 psi 0.15 STR17G 34-ST-03-57
Reference Operative Accuracy Input Output Type Upper Range Minimum Overpressure (% Span) Key Number Limits Span Static Pressure Spec. Analog Overrange Mode 780 mmhg 10 mmhg 1550 mmhg 0.1 STA122 34-ST-03-61 Absolute Pressure or Vacuum 500 psia 50 mmhg 1550 mmhg 0.1 STA922 5 psia 750 psia 0.075 STA140 20 psia 750 psia 0.1 STA940 34-ST-03-66 34-ST-03-61 34-ST-03-66 with Remote Seal 500 psia 5 psia 750 psia 0.1 STR14A Flange mounted open or closed tank with liquid filled or gaseous reference leg. Flange on high pressure side of meter body. (Flush or Extended Diaphragm or Sanitary Flange) 400 inh2o 10 inh2o 690 psi 0.1 STF128 34-ST-03-63 100 psi 5 psi 690 psi 0.1 STF132 34-ST-03-63 300 psi 15 psi 450 psi 0.1 STF15T 34-ST-03-70 Liquid Level, Vacuum, Differential Pressure or Gauge Pressure Flange mounted open or closed tank with liquid filled or gaseous reference leg. Flange on high pressure side of meter body. (Flush or Extended Diaphragm) 400 inh2o 100 psi 25 inh2o 690 psi 0.1 STF924 34-ST-03-68 5 psi 690 psi 0.1 STF932 34-ST-03-68 1 inh2o 205 psi 0.075 STF12F 34-ST-03-63 Flange mounted open or closed tank with liquid filled or gaseous reference leg. Flange on high pressure side of meter body. (Pseudo Flange) 400 inh2o 600 inh2o 100 psi 25 inh2o 205 psi 0.1 STF92F 34-ST-03-68 25 inh2o 205 psi 0.05 STF14F 34-ST-03-63 0.075 STF13F 34-ST-03-63 5 psi 205 psi 0.1 STF93F 34-ST-03-68 Temperature Temperature STT350 STT250 EN0I-5222 EN0I-6031
Key Number STD120, STD130, STD170, STF12F, STF 13F Weight Meter Body Operating Temperature Limits Pounds Kilograms F C 12.5 5.6 SMA110, SMA120, SMG170 15.4 7 STG140, STG170, STG180 10 4.5 40 to 257 40 to 125 STG14L, STG17L, STG18L 3.8 1.7 STF128, STF132 26.5/47 12/21 STR12D, STR13D, STR14G, STR17G, STR14A, STR93D, STR94G 35/75 16/34 40 to 185 40 to 85 See specs for Process Interface Temperature Limits STD125, STF14F 15.4 7 40 to 185 40 to 85 STF932, STF924 26.5 12 STG974, STG944, STD930, STD924, STD974, STF92F, STF93F 9 4.1 40 to 230 40 to 110 STG97L, STG94L, STG98L 3.8 1.7 STA122, STA140, STA922, STA940 10 4.5 40 to 175 40 to 80 STG15T, STF15T 7 to 15 3.2 to 7 40 to 302 40 to 150 STG93P 3 to 8 1 to 7 5 to 203 15 to 95