LYRA DMX Lyra Bi-Color DMX Flat Panel Light QUICKSTART GUIDE LBX5 Lyra Bi-Color LED Half x 1 Soft Light with DMX LBX10 Lyra Bi-Color LED 1 x 1 Soft Light with DMX What s Included 1 x 15V Power supply 1 x Yoke Mount CHECKED BY www.ikancorp.com 713.272.8822 support@ikancorp.com 2017 ikan Corporation. All rights Reserved
General Information Thank you for buying the ikan Lyra Bi-Color DMX512 LED Lights. This fixture has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance. Every fixture has been thoroughly tested. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your unit for damage and be sure all accessories necessary to operate the unit have arrived intact. In the event damage has been found or parts are missing, please contact our customer support team for further instructions. Please do not return this unit to your dealer without first contacting customer support at the number listed below. Please do not discard the shipping carton in the trash. Please recycle whenever possible. Safety Instructions: This fixture is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow the guidelines in this manual. The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. This device falls under PROTECTION CLASS 1. It s essential this device be grounded properly. Only qualified personnel should perform all electrical connections. INDOOR USE ONLY! DO NOT EXPOSE FIXTURE TO RAIN AND/OR MOISTURE!! DO NOT PLUG FIXTURE INTO A DIMMER PACK! For proper operation, follow the Installation guidelines described in this manual. Only qualified and certified personnel should perform installation of this fixture and only the original rigging parts (yoke) included with this fixture should be used for installation. Any modifications will void the original manufacturer s warranty and increase the risk of damage and/or personal injury. Never look directly into the light source of this fixture to prevent risk of injury to your retina, which may induce blindness. Always disconnect from main power source before performing any type of service and/or cleaning procedure. Only handle the power supply by the plug end, never pull out the plug by tugging the wire portion of the cord. Do not operate this fixture if the power cord has become frayed, crimped and/or damaged. If the power cord is damaged, replace it immediately with a new one of similar power rating. General Guidelines: NEVER OPEN THIS FIXTURE WHILE IN USE!! Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while operating, to prevent any fire hazard. The fixture must be installed in a location with adequate ventilation, at least 1.5 feet (.5m) from adjacent surfaces. Be sure no air ventilation slots are blocked. DO NOT attempt installation and/or operation without knowledge of how to do so. DO NOT permit operation by persons who are not qualified to operate this type of fixture. Most damages are the result of operations by nonprofessionals. Consistent operational breaks may ensure the fixture will function properly for many years to come. DO NOT shake fixture and avoid using brute force when installing and/or operating the fixture. Always install the fixture with an appropriate safety cable. When installing the fixture in a suspended environment, always use correct mounting hardware that can be inserted into the Baby 1/8" or Junior 1-1/8" combo pin adaptor. Use the original packaging and materials to transport the fixture in for service.
Fixture Overview (Front) LBX10 LBX5 Fixture Overview (Back) LBX10 LBX5
Fixture Menu ON-BOARD SYSTEM MENU The fixture comes with an easy to navigate system menu. The next section will detail the functions of each command in the system menu. LCD MENU CONTROL KNOB The control knob allows for local control as well as control from DMX board. The local control gives the user adjustment from 10%-100% in brightness. On Bi-Color fixtures, the local knob gives the user the ability to switch from 5600K -3200K just by pressing down on the large yellow dial. The user can also adjust the DMX channels 1 thru 512 by pressing down again on the large yellow dial. DMX Channel The DMX512 channel selection can be made from the back of the fixture using the large yellow knob to dial in the correct DMX number. When a DMX signal is detected on the fixture, all other controls are closed down and only DMX channel control can be selected on the rear of the fixture. Depending on DMX channel selected a bi-color light will require two channels for use on the DMX board. 100% will be the 5600K color output. 0% will be the 3200K color output. The middle position will be 4600K color output. Example: Channel Brightness Color 5 & 6 Channel 5 Channel 6 Cleaning & Maintenance CAUTION! DISCONNECT POWER BEFORE CLEANING OR MAINTENANCE! CLEANING Frequent cleaning is recommended to insure proper function, optimized light output, and an extended life. The frequency of cleaning depends on the environment in which the fixture operates: damp, smoky, or particularly dirty environments can cause greater accumulation of dirt on the fixture. Never use alcohol, solvents, or ammonia- based cleaners MAINTENANCE Regular inspections are recommended to insure proper function and extended life. There are no user serviceable parts inside this fixture. Please refer all other service issues to an authorized ikan service technician. Should you need any spare parts, please order genuine parts from your local ikan dealer. Please refer to the following points during routine inspections: Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. Check for any deformations on the housing, rigging hardware and rigging points (ceiling, suspension, trussing). Deformations in the housing could allow for dust to enter into the fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person(s). Electric power supplies and cables must not show any damage or fraying. Never remove the ground prong from the power cable.
Specifications LBX5 Fixture Specifications Light Source 510 0.2 watt LEDs Head Type Bi-Color 5600K-3200K Lens ½ Stop Soft Diffusion Beam Angle 110 Control / Dimming Knob Control Build Material Heavy Duty Resin Plastic Cooling System Passive Cooling Yoke Baby 5/8" -- Junior 1 1/8" Combo Pin Fixture Size 14 x 8 x 3 in. Fixture Weight 4 lbs LBX10 Fixture Specifications Light Source 900 0.2 watt LEDs Head Type Bi-Color 5600K-3200K Lens ½ Stop Soft Diffusion Beam Angle 110 Control / Dimming Knob Control Build Material Heavy Duty Resin Plastic Cooling System Passive Cooling Yoke Baby 5/8" --Junior 1 1/8" Combo Pin Fixture Size 14 x 14 x 3 in. Fixture Weight 6 lbs LBX5 Electrical Specifications Power Supply Power Consumption Input: 110-220VAC Output: 15VDC 51W; 14-18VDC LBX10 Electrical Specifications Power Supply Power Consumption Input: 110-220VAC Output: 15VDC 90W; 14-18VDC Optional Accessories Some other products that work well with the Lyra DMX Lights available from Ikan include: CV600 CP-STND-V3 KCP-703 PWRGP-01 ROLLR-STND10 SW-04 IDX-096 Digital LED Light Meter with Exposure & Spectrometer Compact Light Stand Version 3 Stage Clamp with 16mm Stud Power Grip 2-Stage Roller Stand 10ft 6in Safety Wire 96 Channel DMX Console
Learn More More dynamic information at official website: www.ikancorp.com Support Contact email: support@ikancorp.com Ikan: and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product. CONDITIONS OF WARRANTY SERVICE Free service for one year from the day of purchase if the problem is caused by manufacturing errors. The components and maintenance service fee will be charged if the warranty period is expired. Free Service will not be Provided in the Following Situations:(*Even if the product is still within the warranty period.) Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company. Damage caused by natural disaster, abnormal voltage, and environmental factors, etc. 2017 ikan Corporation. All rights reserved