SIG CHA Timeswitch SRVIC ITRVA ifestyle DUA CHA Programmer for heating OR hot water for heating AD hot water PSi, PSi PSi, P5Si, PSi SIG CHA DUA CHA Installation Instructions 069005000 ISSC Invensys Controls urope Sales: 085 055 / Technical Helpline: 085 0 mail: customer.care@invensyscontrols.com / Web: www.draytoncontrols.co.uk
ISTAATIO ISTRUCTIOS PAS OT: ISTAATIO MUST OY B CARRID OUT BY A QUAIFID CTRICIA OR HATIG GIR. MAK SUR MAIS IPUT HAS A AMP FUS. TCHICA DATA PSi, P5Si & PSi PROGRAMMRS PSi & PSi TIMSWITCHS Voltage Programmer Rating Timeswitch Rating 0V AC +0% - 0% 50Hz () A 0V AC each switch () A 0V AC Ambient temp Operating: 0º to 5ºC Storage: -0ºC to 50ºC Without mains power Programming resolution Wiring Maintenance Display: blank Time: always kept Program times: always preserved minute Fixed wiring only, to comply with current I regulations Must be maintained by a qualified electrician or heating engineer ifestyle Programmers and Timeswitches conform to the essential requirements of these Directives: 89/6/C lectromagnetic compatibility //C ow voltage
BFOR ISTAATIO First, make sure the mains supply is switched off! PROGRAMMR OY The programmer must be set to the type of system it is to control. The link on the back of the unit has two settings P and G. P = a fully pumped and controlled system allowing heating and hot water to be set separately. G = a gravity-fed hot water system which does not allow independent setting of heating without hot water, though hot water can be controlled alone. USIG A XISTIG WA-PAT oosen the securing screws on the old programmer and unplug it. Check that there s 0mm clearance to the right of the wall-plate, and 5mm above it. Check the chart on the next page to compare terminals and if necessary, change the wiring of the wall-plate to suit. ow plug the ifestyle unit into the wall-plate and tighten the securing screws. Check the A fuse, and switch on the mains. FITTIG A W WA-PAT The ideal location is.m above floor level, with reasonable lighting, good access, no condensation, no extremes of temperature, and a supporting surface that fully covers the back of the unit. Position with 0mm clearance to the right, 5mm above, and sufficient room to access the securing screws underneath. Fix, with terminals at the top, either direct to a flat wall using wall plugs and o. 6 x (5mm) woodscrews, or on a flush mounting single conduit box type UA (BS66) using M.5 x bolts. DO OT US A SURFAC MOUTIG BOX.
TIMSWITCH TRMIA COMPARISOS MAK MOD arth eutral ive Common On Off Spare Current Models Drayton Tempus, (new models) ifestyle P, P Switchmaster 00 Discontinued/Competitors Models AC TC (Towerchron) Drayton Tempus, (old models) Switchmaster 980 Danfoss Randall TS5, 5 (Mk8) 5/6 Danfoss Randall TS5 Danfoss Randall TS95 5 6,, Danfoss Randall ST, ST 5 6 Danfoss Randall ST 5 6 Danfoss Randall 0, 0, 05, 0 5 6 Danfoss Randall 9, 9 5 6 Grasslin Towerchron Q Grasslin Towerchron T00, T00Q Honeywell ST 600A, ST 600C Honeywell ST 000B Horstmann Centaur SC, SC Horstmann Centaur Plus, C, C Horstmann merald, Pearl Auto Horstmann 5, Coronet, H, H 5 6 andis & Staefa RWB andis & Staefa RWB0, RWB50, 00, 5, 0 andis & Staefa RWB Potterton Myson P000, 00, 00, 500 5 Sangamo M6 6 Smiths Centroller Mk, Mk Smiths Centroller 0 /5 Smiths Centroller 00, 980 Sunvic Select 0 Sunvic SP0, SP5 5 S Venner Vennerette I OAD
PROGRAMMR TRMIA COMPARISOS MAK MOD arth eutral ive H/W off C/H off H/W on C/H on Current Models Drayton Tempus 6, (new models) ifestyle P, P, P5, P Switchmaster 00, 600 (no connection to terminal on 600) Switchmaster 805 Discontinued/Competitors Models AC MP (Towerchron) 6 0 AC FP (Towerchron) 8 6 0 Drayton Tempus,, 6, (old models) Switchmaster 905, 900 Danfoss Randall CP5, CP5, FP5, FP5 (Mk8) Danfoss Randall 00P, 060 6 Danfoss Randall 0 (link -6) 6 5 Danfoss Randall 0, 0, 05, 0 (link 6-) 5 6 Danfoss Randall 0 (link -5 and 5-6) Danfoss Randall 0 (link -5 and 5-6) Danfoss Randall 9, 9 (link - and -5) 6 Danfoss Randall ST, ST, ST, STM, FP95 6 ST5 (link - and -5) Grasslin Towerchron DP, Q Honeywell ST 699/99 (link -5 and 5-8) 6 Honeywell ST 600, ST 600, ST 600, ST 650 Honeywell ST 00 (link - and -6) 8 5 Horstmann 55, 5, 5 Diadem, H, H, 6 H, Tiara (link - and -5) Horstmann Centaur Plus, C, C andis & Staefa* RWB, RWB, 0, 0, 0, 00, 5 & 0, RWB9 Myson Microtimer (link -5 and 5-8) 6 Potterton Myson All P000 s, P000 s, P6000 s (link -5 and -) Potterton Myson* Mini Minder Sunvic Select 0 Sunvic SP50, SP00 (link -) 5
WIRIG TH TIMSWITCH Make the wiring connections as above. ote that the output contacts are voltage-free, so power needs to be put on to Terminal either by linking from Terminal or from a separate supply with a A fuse. WIRIG TH PROGRAMMR USIG A DRAYTO SIMP--FIT, ATHOUGH OT CSSARY, WI MAK THIS ISTAATIO ASIR. Connection Charts Arrowed numbers relate to the junction box. Consult boiler handbook for details of pump overrun wiring. *Thermostat Key C Common H Call for Heat S Satisfied eutral arth ive Wiring Colour Codes GR Grey Y Yellow BK Black B Blue BR Brown RD Red W White OR Orange YG Yellow/Green
WIRIG TH PROGRAMMR Cont... Connection Charts ROOM THRMOSTAT * RTS & RTS,5&6 TS C H # 5 #- IK - FOR 0V OUTPUT Switched and Fused (A) Mains input For pump overrun boilers consult manufacturer's instructions See Thermostat Key Gravity HW, Pumped CH with Room Stats PROGRAMMR JUCTIO BOX WC ST TO 'G' 5 6 8 9 0 5 PUMP BOIR ROOM THRMOSTAT RTS & RTS,5&6 TS C H # Mid-Position Valve System PROGRAMMR ST TO 'P' CYIDR THRMOSTAT * S C H HTS C 5 #- IK - FOR 0V OUTPUT Switched and Fused (A) Mains input For pump overrun boilers consult manufacturer's instructions See Thermostat Key * 5 8 W 8 JUCTIO BOX WC 6 5 6 8 9 0 GR OR B YG MID-POSITIO VAV IFSTY 69H0-00 (mm) IFSTY 9H0-00 (8mm) DRAYTO FOWSHAR Honeywell V0A andis & Gyr MAV 8 6 PUMP BOIR
ROOM THRMOSTAT RTS & RTS,5&6 TS C H # Spring-Return -Valve System PROGRAMMR ST TO 'P' CYIDR THRMOSTAT * S C H HTS C * 5 #- IK - FOR 0V OUTPUT Switched and Fused (A) Mains input For pump overrun boilers consult manufacturer's instructions See Thermostat Key JUCTIO BOX 5 GR OR BR B YG CH VAV WC 6 5 6 8 9 0 IFSTY 69H08-0 IFSTY 9H500 DRAYTO ZV Honeywell V0H056 andis & Gyr ZAV 8 GR OR BR B YG DHW VAV 8 6 PUMP BOIR Make the wiring connections, as above, for the appropriate system. For surface wiring, snap out the cable entry strip on the bottom edge of the wall-plate. ifestyle units are double-insulated and need no earth connection, but an earthing continuity (loop) terminal is provided for convenience. ISTARS/GIRS OTS After wiring, plug in the unit and tighten the securing screws. Check the mains input has a A fuse, and switch on the mains. Then set the timings as shown in the User s Guide. AWAYS SWITCH OFF TH MAIS BFOR RMOVIG TH IFSTY TIMSWITCH/PROGRAMMR AD VR FIT IT TO A IV WA-PAT! SRVIC ITRA FATUR Applicable to all models. If you wish to activate, or adjust, the settings for the service interval feature then please refer to the instructions for the service interval (P Si) reset module [SOD SPARATY] Invensys Controls urope Sales: 085 055 / Technical Helpline: 085 0 mail: customer.care@invensyscontrols.com / Web: www.draytoncontrols.co.uk