VersaVac High-Performance Bagless Vacuum PLU team Mop Enjoy Thank you for purchasing the Oreck VersaVac high performance bagless vacuum plus steam mop. imply install the handle and you are ready to enjoy your new Oreck VersaVac. Welcome to our all. lick. Visit. customer service program. To speak with an Oreck representative call or click using the information below. all UA: 1 800 989 anada: 1 888 7 7 lick www.oreck.com Visit Visit one of our many Oreck store locations ontents Parts... afety... Operation... Use & Maintenance... Troubleshooting & Parts... French...7 panish...11 1
LOK 1 ord Release Water Tank Release Lever Water Tank Replaceable Hard Water Filter Debris up team Trigger 7 Function elector Dial (team//vacuum No Brush/Vacuum With Brush) 8 team /team Ready/Brush On Indicator Lights 9 Infinitely Variable - team Level Adjustment Dial 10 team Mop Pad Holder 11 Microfiber team Mop Pad 1 Power ord 1 Power Head 1 Brushroll 1 Unlock/Lock Button 1 UH UH TILE/ 1 (underneath unit) 1 11 10 Parts 7 8 1 9 1 The Oreck steam mop and vacuum is designed for use on hard surfaces such as ceramic, glass, stone, marble, concrete, vinyl, linoleum and sealed hardwoods. This product is not for use on fine silks, leather, velour, or other delicate steam-sensitive materials, waxed polished furniture, very thin plastics, unsealed hardwoods, ceilings, drywall and exterior paint of automobiles, electronics or items using electricity. NO: Heat and steam may not be suitable for any flooring that is steam or heat-sensitive. If unsure, we recommend checking the use and care instructions from the flooring manufacturer and testing on an inconspicuous area prior to use. TILE/ UNLOK UH! IMPORTANT AFETY INTRUTI When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INTRUTI BEFORE UING THI UUM & MOP! WARNING!: Do not leave appliance unattended when plugged in. Unplug from outlet when not in use and before servicing. Do not use outdoors or on wet surfaces. Do not operate the unit while in the upright and locked position. Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation. Do not allow to be used as a toy. lose attention is necessary when used near children. Use only as described in this manual. Use only manufacturer s recommended attachments. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center or call customer service at: U: 1-800-989- anada: 1-888-7-7 Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord around sharp edges or corners. Keep cord away from heated surfaces. Do not run appliance over cord. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. Do not handle plug or appliance with wet hands. Do not use without the tank cap in place. Do not operate the steam function without water in the tank. Empty the water tank when the steam cleaner is not in use. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce performance. Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts. To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not alter the plug in any way. To reduce the risk of fire, electric shock, or injury: Turn off all controls before unplugging. Do not use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes. Use extra care when cleaning on stairs. Do not use to pick up flammable or combustible liquids, such as gasoline or lighter fluid, or use in areas where they may be present. Do not use appliance in an enclosed space where flammable, explosive or toxic vapors are given off by oil base paint, paint thinner, some mothproofing substances, or in an area where flammable dust is present. Do not pick up toxic material such as chlorine bleach, drain cleaner, gasoline, etc. with this appliance. Never put additives (such as perfume, stain remover or products containing alcohol) in the water as they may damage the steam cleaner or make it dangerous to you. Product contains chemicals known to the tate of alifornia to cause cancer and birth defects. Ensure that the water tank s closure cap has been screwed down fully before use. Do not touch any hot areas on the appliance. It is normal for the appliance to heat up during operation. Do not use the appliance to treat any item of clothing while being worn on the body. The force and heat of the steam may have an adverse effect on some materials. Always test the steamer on a small concealed area to determine if it is suitable for treatment with the steam cleaner. Never aim the appliance at people, animals or plants (risk of scalding!). Do not aim the appliance at electrical systems or wires. AVE THEE INTRUTI Household Use Only
OPERATI UNLOK LOK Assembly ord Release - To remove cord, twist cord release 1/ turn. lide cord off cord handle.. Easy Power ord torage - Turn cord release to the up position, wrap power cord around cord release and lower cord bracket located below the carry handle. 7 arry Handle - arry handle is located on the back of the appliance for easy lifting, carrying, and use on stairs. 8 UH Turn the function selector dial all the way to the right for the suction and brushroll functions. 9. To empty the debris cup grasp the cup handle, press the release button and lift out. 10 10. Press the release button on the front of the cup to open and empty. 11. Replace the debris cup. NO: Do not operate the vacuum without debris cup in place. 9 Release Button TILE/ TILE/ NO: Remove steam mop pad holder when vacuuming. 8. UH Operating the Oreck Vacuum Turn the function selector dial to UUM for hard surface floors, such as vinyl, wood or tile. Microfiber team Mop Pad Holder A. To attach the Oreck VersaVac s microfiber steam mop pad holder, lower the power head onto the microfiber steam mop pad holder. B. To remove the Oreck VersaVac s microfiber steam mop pad holder, place foot on release pedal and lift the Oreck VersaVac appliance away from the microfiber steam mop pad holder. 7. UH TILE/. UH. 1. Up-Position Lock - Place foot on power head and lean handle back gently to release lock for use. Return handle to the full upright position to engage lock.. UH Align the connector tab at the bottom of the Oreck VersaVac handle with the receiving port on top of the unit. Insert until a snap is heard. UH 1.
OPERATI team Mop Operation Align and attach the microfiber steam mop pad to the microfiber steam mop pad holder.. To attach the Oreck VersaVac s microfiber steam mop pad holder: insert the front of vacuum into the holder, align the foot pedal to the center of the power head, lower the power head onto the holder and LIGHTLY press down to snap into place. NO: Never operate the steam mop without the microfiber steam mop pad in place.. Grasp the water tank release lever and pull forward and up to remove the water tank.. Remove cap from the water tank bottom and fill with water. Make sure the cap gasket is in place. Replace the cap and reinstall the water tank. NO: Do not attempt to use steam mop without water in tank.. Turn the function selector dial left to steam. The light will illuminate.. Rotate the steam selector level adjustment dial so it matches the steam level (Hardwood, Linoleum, and Tile/tone) to the type of floor you want to clean. 7. When the light comes on, press and hold the team Trigger (inside the handle) to begin steam cleaning. For extended steaming, hold the team Trigger in and slide the Unlock/Lock button forward. This will lock the trigger for continued steaming without holding the trigger manually. Be sure to release the trigger lock when finished steaming. 8. When the Oreck team Mop stops emitting steam turn the power and refill the water tank. 9. team ettings: UH FF OF V UH A A E A M O N TILE/ 1. LOW UH UH Tile/tone = Medium to High Linoleum = Low to Medium ealed Hardwoods = Low TILE/ TILE/ UH UH R NO: When the microfiber steam mop pad becomes very wet or dirty, replace with a clean cloth. 7 UH UNLO K LOK team Trigger B UH TILE/
UE & MAINNANE Maintenance 1. When you have finished steam cleaning, ensure the OREK VersaVac s function selector dial is turned to the position and that the plug is removed from the wall. Exhaust Filter Maintenance Remove filter cover by pushing down on the tab and pulling away from the unit. Remove filter from the back side of cover and rinse until clean, then allow the filter to dry thoroughly before placing it back in the filter cover. Install the filter cover by aligning the bottom of the cover with the unit and then pivoting the cover into place. over will make a snap sound when it is in place.. Empty the remaining water from the water tank.. Remove Microfiber steam mop pad and launder. The steam pads can be machine washed in hot water, up to 10 F. For heavily soiled pads, soak in warm water with detergent or a mild stain remover. Allow cloths to dry completely before storing. NO: DO NOT UE FAI OFNER Replacing the Hard Water Filter The hard water filter will help filter minerals that reduce the effectiveness of the steam cleaner. Depending on hard water conditions and/or use frequency, the filter should be replaced every 1 months. The Oreck VersaVac will work using plain tap water. However, if you live in a hard water area, the minerals that form the hard water will reduce the life of the water filter installed in the Oreck VersaVac. This will eventually allow deposits to build up in the heater of your product, which will reduce its performance. To prolong the life of your filter and heater, we recommend using distilled or de-mineralized water in your product in hard water areas.! WARNING: Unplug cord from electrical outlet before servicing. Brushroll Maintenance A little preventative maintenance will keep your OREK VersaVac looking new and will ensure continued cleaning effectiveness. Remove brushroll at least once a month to check for and remove excessive lint, string or hair from the revolving brushroll. Vacuum Filter Maintenance Remove dust bin from unit. Pull filter assembly from the dust bin. Rotate course outer filter counter clockwise and remove the course filter. Rotate main filter counter clockwise and remove the main filter. Pull foam outer filter off the bottom of the main filter. Rinse the course filter, foam filter, and main filter and allow to dry thoroughly before reassembling the filter. Place foam filter back over the main filter from the bottom. Insert the main filter into the filter housing. Rotate main filter clockwise to install the main filter. Place the coarse filter over the main filter and align the unlock symbol with the arrow on the coarse filter. Rotate course outer filter clockwise until you hear a click to install the course filter. Place filter assembly back into the dust bin. Replace the dust bin back into the unit. When the brushroll stalls, the UHROLL light will flash. To reset turn switch to off and back on. If an obstruction is present, unplug unit and remove the obstructing object. Plug the unit back in and the VersaVac is ready to clean. IMPORTANT: To remove brushroll, rotate brushroll release screw 1/ turn until the indicator is aligned with the unlock symbol. Replacing the Brushroll The brushroll is designed for long life. hould it ever become worn or frayed, it can be replaced by an OREK authorized ervice enter.
TROUBLEHOOTING & PART ervice problems that appear to be major can often be solved easily. You can be your own troubleshooter by reviewing this guide. All other servicing should be done by an OREK authorized service center. Problem heck What To Do Unit has no power. Brushroll is not turning. Brushroll Indicator is flashing. Appliance is not properly plugged into an electrical outlet or is not switched on. The electrical socket is faulty. Large debris has clogged the inlet. Large debris has stopped the brushroll. Debris has blocked the brushroll from turning. Brushroll is free to move. Insert plug into an electrical outlet and switch the steam cleaner on. heck the socket by unplugging the steam cleaner and plugging it into a different electrical socket. lean debris from inlet. If the brushroll becomes clogged, brushroll will stop and the UHROLL light will flash. Unplug the unit and clear the obstruction and turn the selector switch off. If the obstruction is clear, the brushroll will start when the switch is turned back to the Brushroll mode. Remove obstruction. Turn unit off using the function selector switch then turn unit back on. Turn unit off using the function selector switch then turn unit back on. If flashing continues, ontact an Oreck Authorized ervice enter. Vacuum does not pick up. Dirt up is full. Large Debris has clogged inlet. Filter needs cleaning. Brushroll is not turning. Brushroll is worn. Empty Dirt up. lean debris from inlet. ee Filter Maintenance ection (page ). ee above in Troubleshooting Guide. ontact Oreck Authorized ervice enter. Very low or no steam is emitted when the steam cleaner is on. The tank is empty. Trigger is not depressed. team function is not selected. team Ready Indicator is not lit. Hard Water Filter needs replacing. Make sure water tank is full of water. Pull steam trigger to activate pump. Verify function selector is set to. Wait for Indicator to light. If it does not turn on after 1 minute, ontact Oreck Authorized ervice enter. ee Replacing the Hard Water Filter ection (page ). teamer still does not operate properly. heck all the above points. ontact Oreck Authorized ervice enter. All accessories and replacement parts are sold separately. To order, call our customer service hotline or visit our website. Please have your model number from the data label on the bottom of the unit. Item Pack of Microfiber Pads Replacement Water Filter Replacement Air Filter Replacement Parts ustomer ervice Hotline UA: 1-800-989- anada: 1-888-7-7 Website: www.oreck.com Part Number VKIT VWFLTR VAFLTR