REGULATORY ENVIRONMENT ON ELECTRICAL AND ELECTRONIC PRODUCT IN MALAYIA Table of Contents I. Rationale for Regulation II. III. IV. Regulatory Authority Legislative Framework Mandatory tandards V. Mode of Regulation and Types of Conformity Assessment Regimes VI. VII. VIII. IX. Flow chart of each Member Country's Regime Voltage, Frequency and Mains Plug Configuration Other Information Contact Person Page 1 of 50
I. RATIONALE FOR REGULATION COUNTRY Malaysia RATIONALE FOR REGULATION Ensure safety and consumer protection. II. REGULATION BODY COUNTRY Malaysia REGULATORY BODY Energy Commission(uruhanjaya Tenaga) III. LEGILATIVE FRAMEWORK COUNTRY LEGILATIVE FRAMEWORK Malaysia Electricity upply Act 1990; and Electricity Regulations 1994. Electricity (Amendment) Regulations 2013. Page 2 of 50
IV. MANDATORYTANDARD Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent of Alignment tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination Malaysia 1 PLUG TOP/PLUG(15A and below) Flat Non- M1578:2003 BEN 50075:1991 - Rewirable Two Pole Plug with supply cord (max.2.5a) 13A Fused Plug M589-1:2011 B1363:PT.1:1995+A1,A2,A3-15A Plug M1577:2003 No corresponding international standard - Appliance Coupler MIEC60320-1:2010 IEC60320-1:2007 Interconnection MIEC60320-1:2010 Coupler MIEC60320-2-2:2011 IEC60320-1:2007 IEC60320-2-2:1998 Adaptor M589PT.3:2012 B1363PT.3:1995+A1,A2+A3 - (Multiways) Integrated Adaptor M1144:1998 B5733:2010 - Travel adaptor No corresponding M IEC60884-1:2006 IEC60884-2-5:1995 Electrical Connector (connecting device) MIEC60998-1:2005 IEC60998-1:2002 Page 3 of 50
Connecting device with screw type clamping unit MIEC60998-1:2005 MIEC60998-2-1:2005 IEC60998-1:2002 IEC60998-2-1:2002 Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination Connecting device with screw-less type clamping unit Connecting device with insulationpiercing clamping units Twist-on connecting device Connecting boxes MIEC60998-1:2005 MIEC60998-2-2:2005 MIEC60998-1:2005 MIEC60998-2-3:2005 MIEC60998-1:2005 MIEC60998-2-4:2005 M 1873:2005 M 1873-22:2006 IEC60998-1:2002 IEC60998-2-2:2005 IEC60998-1:2002 IEC60998-2-3:2002 IEC60998-1:2002 IEC60998-2-4:2002 IEC 60670-1:2002 IEC 60670-22:2002 2 WITCHE AND DIMMER General purpose witch Door Bell & Chime MIEC60669-1:2012 IEC60669-1:2007 M IEC 61558-1:2005 M IEC 61558-2-8:2007 IEC 61558-1:2009 IEC 61558-2-8:2010 Page 4 of 50
Electronic witch MIEC60669-1:2012 MIEC60669-2-1:2012 IEC60669-1:2007 IEC60669-2-1:2009 Remote-control witch MIEC60669-1:2012 MIEC60669-2-2:2012 IEC60669-1:2007 IEC60669-2-2:2006 Country Total Product Product type or grouping Time Delay witch Domestic tandards MIEC60669-1:2012 MIEC60669-2-3:2012 Please tick box if mandatory TANDARD Relevant International tandards IEC60669-1:2007 IEC60669-2-3:2006 Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), Cooker Control Unit No corresponding M B4177:1992-3 OCKET OUTLE(15A and below) Electric haver ocket Outlets MIEC61558-1:2005 MIEC61558-2-5:2006 IEC61558-1:2009 IEC61558-2-5:2010 13Awitch& Unswitch socket outlet 15Asocket outlet & Plug Portable2pin socket outlet class II Portable cable reel M589:PT.2:2011 B1363:PT2: 1995+A1,A2,A3 M1577:2003 No corresponding international standard M1579:2003 No corresponding international standard M1141:2006 IEC 61242:2008 with modification - - - - 4 FLUORECENT LAMP HOLDER/TARTER HOLDER Page 5 of 50
Lamp holders for tubular fluorescent tater holders for tubular fluorescent MIEC60400:2006 IEC60400:2004 MIEC60400:2006 IEC60400:2004 Page 6 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination 5 CEILING ROE Ceiling roses M770:1982 B67:1987 - Edison crew Lamp holder MIEC60238:2008 IEC60238:2004 6 BAYONET CAP AND MULTIWAY ADAPTOR -Bayonet No corresponding M IEC61184:2008+A1 - Lamp holders -Bayonet Adaptors M769:2006 with IEC 61184:2008 IEC61184:2008 with M 769:2006-7 LAMP FITTING Page 7 of 50
-Fixed general purpose luminaries (Excluding Tube/Bulb) -Batten Luminaries (excluding Tube/Bulb), -Luminaries with selfballasted florescent lamp. MIEC60598-1:2012 MIEC60598-2-1:1997 IEC60598 1:2008 IEC60598-2-1:1987 Page 8 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination Recessed Luminaries (excluding Tube/Bulb) Glow-starters for tubular fluorescent elf-ballasted Compact Florescent Lamp (CFL)with Edison screw or bayonet caps Lamp controlgear: Particular requirements for d.c or a.c supplied electronic controlgear for LEDmodules MIEC60598-1:2012 MIEC60598-2-2:1998 IEC60598 1:2008 IEC60598-2-2:2011 MIEC60155:1996 IEC60155:2006 MIEC60968:2006 MIEC60969:2006 (performance) MIEC61347-1:2012 MIEC61347-2- 13:2012(P) IEC60968:1999 IEC60969:2001 IEC61347-1:2010 IEC61347-2-13:2006 & E Page 9 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination LED Lampholder (Connectors for LED-modules) LED Modules for general lighting (eg.double capped selfballasted LED lamp) elf-ballasted single capped LED-lamps for general lighting services by voltage>50v MIEC60838-1:2008 MIEC60838-2-2:2008 MIEC62031:2011with MIEC60061-1:2005 8 CAPACITOR FOR FLUORECENT LAMP IEC60838-1:2004 IEC60838-2-2:2006 IEC62031:2008+A1with IEC60061-1:2005 Malaysia also accept IEC 62776:2014 MIEC62560:2012 IEC62560:2011 & E & E Capacitors for use in tubular fluorescent lamps and other circuits circuit MIEC61048:2006 MIEC61049:1999 IEC61048:2006 IEC61049:1991 Page 10 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination 9 BALLAT/ CONTROLGEAR/DRIVERFORLAMP Malaysia Magnetic Ballast for tabular fluorescent lamp MIEC61347-1:2012 MIEC61347-2-8:2003 M 141 PT.2:1993+A1 IEC61347-1:2010 IEC61347-2-8:2000 IEC60921:2004 with modification Additional ballast lost requirement Electronic Ballast for fluorescent lamp MIEC61347-1:2012 MIEC61347-2-3:2003 MIEC60929:2008 with MIEC61000-3- 2:2003(EMC) IEC61347-1:2010 IEC61347-2-3:2000 IEC60929:2011 with IEC61000-3-2:2009 Control Gear MIEC61347-1:2012 IEC61347-1:2010 Page 11 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent of Alignment tate reason if 10 CIRCUIT BREAKER including AC CURRENT OPERATED EARTH LEAKAGE CIRCUIT BREAKER and MINIATURE CIRCUIT BREAKER Indicate whether requires: afety (), Environment (E), EMC, or combination Residual Current Circuit Breaker (RCCB) Residual Current Breaker with Overcurrent Protection (RCBO) MIEC61008-1:2012 MIEC61008-2-1:2003 Or MIEC61008-1:2012 MIEC61008-2-2:2003 MIEC61009-1:2012 MIEC61009-2-1:2003 or MIEC61009-1:2012 MIEC61009-2-2:2003 IEC61008-1:2010 IEC61008-2-1:1990 or IEC61008-1:2010 IEC61008-2-2:1990 IEC61009-1:2010 IEC61009-2-1:1991 or IEC61009-1:2010 IEC61009-2-2:1991 Miniature Circuit Breaker (MCB)for ac Miniature Circuit Breaker (MCB)for ac & dc MIEC60898-1:2007 IEC60898-1:2003 MIEC60898-2:2007 IEC60898-2:2003 Fuse Base & Carrier up to 32A MIEC60269-1:2011 MIEC60296-2:2011 IEC60269-1:2006 IEC60269-2:2006 Page 12 of 50
Fuse/Fuse Link up to 63A MIEC60269-2:2011 MIEC60269-3:2011 IEC60269-2:2006 IEC60269-3:2010 Page 13 of 50
Country Total Product Product type or grouping witch fuse up to 63A. Domestic tandards MIEC60947-1:2010 MIEC60947-3:2010 Please tick box if mandatory TANDARD Relevant International tandards IEC60947-1:2007 IEC60947-3:2008 Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination 11 PORTABLE LUMINAIRE LAMP -tanding Lamp with detachable Or nondetachable mains supply flexible cord, MIEC60598-1:2012 MIEC60598-2-4:2003 IEC60598-1:2008 IEC60598-2-4:1997 -tanding lamp &adaptor, -Table lamp& adaptor, -Night Lamp integral with Direct in plug. M IEC 60598-1:2012 M IEC 60598-2-12:2010 IEC 60598-1:2008 IEC 60598-2-12:2006 -Portable LED Lamp Hand Lamp & adaptor, MIEC60598-1:2012 MIEC60598-2-8:2006 IEC60598-1:2008 IEC60598-2-8:2007 Page 14 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination 12 KETTLE including HEATINGEL EMENT IF UPPLIED EPARATELY Warming Plate MIEC60335-1:2013 MIEC60335-2-12:2014 IEC60335-2-12:2002 Deep Fryer Heating Liquids such as: Coffee/Tea Maker, Food teamer, Egg Boiler, Jug, low Cooker, teamboat, Kettle, Airpot, Bottle Warmer, terillizer. MIEC60335-1:2013 MIEC60335-2-13:2006 MIEC60335-1:2013 MIEC60335-2-15:2004 IEC60335-2-13:2004 IEC60335-2-15:2002 Multi-purpose cooker MIEC60335-1:2013 MIEC60335-2-9:2014 MIEC60335-2-13:2006 MIEC60335-2-15:2004 IEC60335-2-9:2008 IEC60335-2-13:2004 IEC60335-2-15:2002 Water Dispenser/Filter MIEC60335-1:2005 IEC60335-1:2004 Page 15 of 50
Water Dispenser -Hot MIEC60335-1:2005 MIEC60335-2-15:2004 IEC60335-1:2004 IEC60335-2-15:2002 Page 16 of 50
Country Total Product Product type or grouping Water Dispenser -Cold Domestic tandards MIEC60335-1:2005 MIEC60335-2-24:2015 Please tick box if mandatory TANDARD Relevant International tandards IEC60335-1:2004 IEC60335-2-24:2010 Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination Water Dispenser Hot and Cold MIEC60335-1:2005 MIEC60335-2-15:2004 with MIEC60335-2- 24:2005 IEC60335-1:2004 IEC60335-2-15:2002 with IEC60335-2-24:2010 Built in Hob MIEC60335-1:2013 MIEC60335-2-36:2014 IEC60335-2-36:2008 13 KITCHEN MACHINE Blender, MIEC60335-1:2013 Chopper, MIEC60335-2-14:2014 Food Processor, Juice Extractor, Grinder, Mixer. IEC60335-2-14:2002 14 TOATER/ OVEN (Cooking Appliance) Page 17 of 50
tationary Electric Oven, Induction Hob. MIEC60335-1:2013 MIEC60335-2-6:2014 IEC60335-2-6:2005 Cl.3.1.9.102-water temperature changed to 25 C±5 C Page 18 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination Bread Maker, Bread Toaster, Portable Oven, Induction Cooker, Grill, andwich Maker/Waffle Maker, Roaster. MIEC60335-1:2013 MIEC60335-2-9:2014 IEC60335-2-9:2008 Microwave Oven MIEC60335-1:2013 MIEC60335-2-25:2014 IEC60335-2-25:2010 15 RICE COOKER Rice Cooker MIEC60335-1:2013 MIEC60335-2-15:2004 IEC60335-2-15:2002 16 REFRIGERATOR Refrigerator, Freezer, Minibar. MIEC60335-1:2013 MIEC60335-2-24:2005 IEC60335-2-24:2005 with modification Cl.3.2.9.102-3.2.9.104and Cl.5.7 water temperature changed to 25 C±5 C & E 17 IMMERI ON WATER HEATER Page 19 of 50
Fixed Immersion Heater MIEC60335-1:2013 MIEC60335-2-73:2014 IEC60335-2-73:2009 Page 20 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination Portable Immersion Heater MIEC60335-1:2013 MIEC60335-2-74:2010 IEC60335-2-74:2006 18 WATER HEATER including HEATING ELEMENT IF UPPLIED EPARATELY torage Water MIEC60335-1:2013 Heater M1597-2-21:2015 IEC60335-2- 21:2004with modification Cl.5.7 Additional water having temperature of 30 C±3 C Cl.7.12.1 marking instruction -to incorporate 10 ma RCD in the installation circuit Cl.13-additional leakage current test as a non-conductive isolation barrier at both the water inlet and outlet are incorporated. Page 21 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination Instantaneous Water Heater MIEC60335-1:2013 M1597-2-35:2010 IEC60335-2- 35:2006with modification Cl.3 Change water temperature to 30 C±3 C Cl.6.6-Classification Replace with IP25 7.104 Additional Warning label Cl.22.111and 22.112 Additional requirement for leakage current protection device 19 WAHING MACHINE Washing Machine having drying MIEC60335-1:2013 M1597:Part2-7:2005 IEC60335-2-7:2003 with modification Cl.3.1.9and Cl.6.2 of Annex BB water temperature at inlets intended for cold water changed form15 C±5 C to 25 C±5 C Washing Machine with separate spin container MIEC60335-1:2013 MIEC60335-2-4:2007 M 1597:Part 2-7:2005 IEC60335-1:2008 IEC60335-2-4:2004 IEC 60335-2-7:2003 with modification Page 22 of 50
Tumbler Dryers MIEC60335-1:2013 MIEC60335-2-11:2014 IEC60335-2-11:2012 Page 23 of 50
Country Total Product Product type or grouping Cloth Dryers (on rack located) Domestic tandards MIEC60335-1:2013 IEC 60335:Part2-43:2014 Please tick box if mandatory TANDARD Relevant International tandards IEC60335-2-43:2008 Extent Alignment of tate reason if Cl.3.1.9. water temperature changed to 25 C±5 C Indicate whether requires: afety (), Environment (E), EMC, or combination Dishwasher and other utensils. MIEC60335-1:2013 M1597:Part2-5:2005 IEC60335-2-5:2005 Cl.3.1.9and Cl.6.2 of Annex BB water temperature at inlets intended for cold water changed form15 C±5 C to 25 C±5 C 20 FAN Moving-louver fan, Ceiling fan, Auto fan, Pedestal fan, Table fan, Wall fan& Applies to their separate regulators and with blade. MIEC60335-1:2013 M1597:Part2-80:2010 M1220:2010 IEC60335-2-80:2004 with modification for ceiling fan only IEC60879:1986 with modification M1597:P2: Cl.7.12.1,Cl.21.102 andcl.21.103 New requirement for detachable part, temperature marking, maintenance instruction, moisture resistance, supply & E Page 24 of 50
Country Total Product Product type or grouping Ventilating fan, Decorative fan& Applies to their separate regulators and fan without blade. Domestic tandards MIEC60335-1:2013 M1597:Part2-80:2010 Please tick box if mandatory TANDARD Relevant International tandards IEC60335-2-80:2004 with modification for ceiling fan only Extent Alignment of tate reason if connection, external flexible cord and mechanical strength M1220: 1) Cl7.2: statement with at least five running positions is replaced by with at least three running positions Indicate whether requires: afety (), Environment (E), EMC, or combination 2) Cl10.3.2: Rating of frequency is defined to suit local conditions Range Hood Cleaning Appliances (eg. Air Purifier) MIEC60335-1:2013 MIEC60335-2-31:2014 MIEC60335-1:2013 MIEC60335-2-65:2014 IEC60335-2-31:2009 IEC60335-2-65:2008 Page 25 of 50
Humidifiers (eg. Air Cooler) MIEC60335-1:2013 MIEC60335-2-98:2014 IEC60335-2-98:2008 Page 26 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards 21 HAND OPERATED HAIR DRYER/HAIRCARE/KIN CARE Hair Dryer, MIEC60335-1:2013 Hair tyling et, MIEC60335-2-23:2007 IEC60335-2-23:2005 Ionic Facial teamer or similar to it. Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination 22 IRON Iron Fabric teamer 23 HAVER haver, Hair Clippers. MIEC60335-1:2013 MIEC60335-2-3:2006 MIEC60335-1:2013 MIEC60335-2-85:2014 MIEC60335-1:2013 MIEC60335-2-8:2002 IEC60335-2-3:2005 IEC60335-2-85:2008 IEC60335-2-8:1992+A1 24 VAPORIER Page 27 of 50
Mosquito Matt Vapor, Aroma Vapor (Air Freshener) MIEC60335-1:2013 MIEC60335-2- 101:2014 IEC60335-2-101:2008 Page 28 of 50
Country Total Product Product type or grouping Domestic tandards 25 VACUUM CLEANER Vacuum Cleaner, MIEC60335-1:2013 Water uction MIEC60335-2-2:2006 Cleaning. Please tick box if mandatory TANDARD Relevant International tandards IEC60335-2-2:2004 Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination 26 HI-FIDELITY ET Page 29 of 50
ub-woofer, Amplifier, Cassette Player, Equalizer/ Mixer, Hi-Fi ystem, Karaoke, PA ystem, Portable Hi-Fi ystem, Portable Radio Cassette, Player/ Recorder, Radio, Radio Alarm, Tuner/ Receiver, Turntables/ Record Players, Compact Disc Player, Audio/Video Recorder up to 4 channels. MIEC60065:2007 IEC60065:2005 Malaysia also accept IEC 62368-1:2014. This is for AV and ICT equipment. Page 30 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination 27 VIDEO and VIUAL DIPLAY UNIT Electronic appliances such as: LCD, LED, Plasma, CRT, And similar to it. MIEC60065:2007 IEC60065:2005 Malaysia also accept IEC 62368-1:2014. This is for AV and ICT equipment. 28 AUDIO and VIDEO PLAYER UNIT VCD, MIEC60065:2007 IEC60065:2005 Laser Disc, Video Cassette Malaysia also accept IEC Recorder, 62368-1:2014. This is for DVD, AV and ICT equipment. Video Rewinder, Children Video Game. & E 29 MAAGER Page 31 of 50
Foot Massagers, Massage Bed, Massage Chair, Massage Pads, Handheld Massagers, Massage Belts. MIEC60335-1:2013 MIEC60335-2-32:2014 IEC60335-2-32:2008 Page 32 of 50
Country Total Product Product type or grouping Domestic tandards 30 AIR CONDITIONER plit Air- MIEC60335-1:2013 conditioner, M1597-2-40:2005 Portable Airconditioner, Ceiling Airconditioner (Cooling Capacity of 32,000Btu/hr& below) 31 CHRITMA LIGHT Lighting Chain, MIEC60598-1:2012 Rope Light, MIEC60598-2-20:2013 Decorative/ Festive Light. Please tick box if mandatory TANDARD Relevant International tandards IEC60335-2-40:2005 with modification IEC60598-1:2008 IEC60598-2-20:2010 Extent of Alignment tate reason if - - & E Indicate whether requires: afety (), Environment (E), EMC, or combination 32 DOMETIC POWER TOOL(Portable Type) Drill (Drill bit size up to15 mm) Grinder (up to 100mm) MIEC60745-1:2010 MIEC60745-2-1:2011 MIEC60745-1:2010 MIEC60745-2-3:2010 IEC60745-1:2006 IEC60745-2-1:2006+A IEC60745-1:2006 IEC60745-2-3:2006 Page 33 of 50
ander (up to 300W) MIEC60745-1:2010 MIEC60745-2-4:2011 IEC60745-1:2006 IEC60745-2-4:2006 Page 34 of 50
Country Total Product Product type or grouping Circular aw and circular knife (Cutting Blade upto160mm) pray gun for non-flammable liquid(up to 100 bars) Jig and abre aw(upto60 mm) Planer (up to 500W) Trimmer (up to 300W) Hedge trimmer and Grass shears (up to 750W) Router and trimmer (up to 500W) High Pressure Cleaner ewing Machine Domestic tandards MIEC60745-1:2010 MIEC60745-2-5:2010 MIEC60745-1:2010 MIEC60745-2-7:2005 MIEC60745-1:2010 MIEC60745-2-11:2011 MIEC60745-1:2011 MIEC60745-2-14:2011 MIEC60745-1:2010 MIEC60745-2-15:2011 MIEC60745-1:2010 MIEC60745-2-17:2012 MIEC60335-1:2013 IEC60335-2-79:2007 MIEC60335-1:2013 MIEC60335-2-28:2003 Please tick box if mandatory TANDARD Relevant International tandards IEC60745-1:2006 IEC60745-2-5:2006 IEC60745-1:2006 IEC60745-2-7:1989 IEC60745-1:2006 IEC60745-2-11:2006 IEC60745-1:2006 IEC60745-2-14:2006 IEC60745-1:2006 IEC60745-2-15:2006 IEC60745-1:2006 IEC60745-2-17:2010 IEC60335-2-79:2005 IEC60335-2-28:2002 Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination Page 35 of 50
Country Total Product Product type or grouping Portable Heating Tool such as: oldering Gun, oldering Iron, Heat Gun, Hot Air Firelighters, Glue gun. Domestic tandards MIEC60335-1:2013 MIEC60335-2-45:2003 Please tick box if mandatory TANDARD Relevant International tandards IEC60335-2-45:2002 Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination 33 ADAPTOR/ CHARGER Portable Battery MIEC60335-1:2013 Charger (up to MIEC60335-2-29:2005 12V) Adaptor for IT Equipment(up to20v) General electrical appliances Electronic Isolating Transformer IEC60335-2-29:2002+A1 MIEC60950-1:2007 IEC60950-1:2005 MIEC61558-1:2005 MIEC61558-2-6:2005 IEC61558-1:2009 IEC61558-2-6:2009 witching mode power supply Electric toys MIEC61558-1:2005 MIEC61558-2-17:2007 MIEC61558-1:2005 MIEC61558-2-7:2007 IEC61558-1:2009 IEC61558-2-17:2009 IEC61558-1:2009 IEC61558-2-7:2007 Page 36 of 50
Audio video equipment MIEC60065:2007 IEC60065:2005 Page 37 of 50
Country Total Product Product type or grouping Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent Alignment of tate reason if Indicate whether requires: afety (), Environment (E), EMC, or combination IT & Office products havers MIEC60950-1:2007 IEC60950-1:2005 MIEC60335-1:2013 MIEC60335-2-8:2002 IEC60335-2-8:2000 34 WIRE/ CABLE/CORD(non-armoured)0.5mm² to 35mm² Polyvinyl M2112-5:2009 BEN50525-2-11:2011 chloride(pvc) or Insulated IEC60227-5:2011 Flexible cord and cable NEQ Minor differences in construction and test requirement for cable in Malaysia Rubber insulated cord and flexible cables M140:1987 Or M2127-4 BEN50525-2-11:2011 IEC60245-1:2008 IEC60245-4:2011 NEQ M 140 is based on B6500:1984 PVC-insulated cable (nonarmoured)for electric power and supply: -non-sheathed M2112-3:2009 IEC60227-3:1997 NEQ Minor differences in construction and test requirement for cable in Malaysia Page 38 of 50
Country Total Product Product type or grouping PVC-insulated cable (nonarmoured) for electric power and supply: -sheathed Domestic tandards Please tick box if mandatory TANDARD Relevant International tandards Extent of Alignment tate reason if M2112-4:2009 IEC60227-4:1997 NEQ Minor differences in construction and test requirement for cable in Malaysia Page 39 of 50
V. E OF REGULATION AND TYPE OF CONFORMITY AEMENT REGIME COUNTRY Malaysia TYPE OF CONFORMITY AEMENT REGIME Registration/ Certification E OF REGULATION A Certificate of Approval (CoA) is required. To obtain approval, the following are needed: Test reports from local or foreign laboratories which are acceptable to T. Certificate of Conformity (CoC) from local or foreign Conformity Assessment Bodies (CAB) which are acceptable to T. Electronic submission of CoA application via e-permit to T. Enter the IRIM Product Certification cheme/irim Batch Testing cheme (every consignment is subjected to inspection and testing) Use of IRIM-T label. Page 40 of 50
VI. FLOW CHART OF MEMBER COUNTRIE' REGIME MALAYIA Applicant registers with Dagangnet Registered with T No Apply CoR Yes Online application through epermit. Applicant fills-up information such as:- Name of electrical equipment Brand Model Applicant can refer to Trader Module User Guide Attached Type test report CoR issued Application Rejected MEP Products Yes Attach Type Test Report for MEP (Performance Test Report) No No Correct Information Process Fee RM30.00 Yes CoR = Certificate of Registration to Manufacture/Import No Paid Yes Page 41 of 50
Application re-submitted Energy Commission (T) evaluates based on: Validity of Type test report IRIM BHD/ labs accredited under AMM by DM; Labs under IECEE CB cheme; Labs accredited by APLAC MRA; Labs accredited by ILAC MRA; or Labs listed under AEAN EE MRA National Deviation No Complete CoA Fees :- Yes ingle phase RM 220.00 Three phase RM 330.00 No Paid Yes CoA issued Page 42 of 50
Importer Manufacturer Equipment shall be sent for Consignment Test or PC by IRIM Equipment shall enter PC by IRIM Failed Consignment or PC Passed Passed PC Failed Applicant to reapply IRIM inform T MEP Products Yes Equipment affixed with IRIM-T Label & **EE Label i. T issues letter to applicant as to: inform the cancellation of COA equipment to be sent to country of origin or destroyed ii. Customs will be informed of the cancellation of COA No Equipment affixed with IRIM-T Label ** The artwork for EE label can be obtained by EC. Page 43 of 50
LIT OF REGULATED ELECTRICAL EQUIPMENT THAT ARE TO BE TETED TO THE PECIFIED MINIMUM ENERGY PERFORMANCE TANDARD (MEP) No Equipment Type of Equipment Energy Performance Testing tandards Minimum Energy Performance tandards (MEP) 1. Refrigerator (a) one-door (b) two-door M 2595:2014 2 tar 2. Air Conditioner ingle split wall mounted air conditioner capacity up to 25, 000 Btu/h M 2597:2014 2 tar 3. Television The type of television are of the following list and of size up to or equal to 70 inches: (a) plasma (b) liquid crystal display (LCD) (c) light emitting diode (LED) (d) cathode ray tube (CRT) M 2576:2014 2 tar Page 44 of 50
No Equipment Type of Equipment Energy Performance Testing tandards Minimum Energy Performance tandards (MEP) 4. Domestic Fan (a) wall (b) desk M 2574:2014 2 tar (c) pedestal (d) ceiling 5. Lighting (a) fluorescent (Double cap fluorescent lamp) M 2598:2014 Tubular Fluorescent: Ty pe (W) MEP (lm/w) T8 18<31 70 31 80 T5 14<15 75 15 80 (b) elf ballasted single capped [compact fluorescent lamp (CFL)] c) ingle capped fluorescent lamp (non-integrated compact fluorescent lamp) & circular fluorescent lamp M 2598:2014 M 2598:2014 Compact fluorescent lamp (CFL): Lamp rating (W) MEP (lm/w) <9 46 9 < 15 52 15 <25 55 25 62 Lamp rating (W) MEP (lm/w) <10 46 10 < 19 55 19 <27 59 27 70 Page 45 of 50
No Equipment Type of Equipment Energy Performance Testing tandards Minimum Energy Performance tandards (MEP) d) elf ballasted light emitting diode (LED) M 2598:2014 Light emitting diode (LED): Lamp Cap Type MEP (lm/w) G13 75 GU10 50 E27 / B22d 60 E14 60 (e) incandescent M 2598:2014 incandescent: Type Incandescent Lamp** MEP (lm/w) 20 **The Minimum Energy Performance tandards (MEP) value for incandescent lamp shall not apply for the following use: (a) components in electrical appliances; (b) medical and lab equipment; (c) internal decoration, shows and exhibition; (d) safety and signaling; (e) conservation of animals and as repellant for insects; (f) heating and testing; (g) cleanliness and health; (h) beauty treatment; (i) lamps that cannot be directly replaced with other type of lamp; and (j) incandescent lamp for other purposes deemed suitable by the Commission to be excluded. Page 46 of 50
VII. MAIN VOLTAGE, FREQUENCY AND MAIN PLUG CONFIGURATION Country Malaysia Mains Voltage and Tolerance 230 Volts single phase tolerance +10%-6% Mains Frequency and Tolerance 50Hz ±1% Applicable Legislation Domestic tandard - M589:PT.1: 2011&M589 : PT.2 :2011for 3-pin rectangular type 13-Amp plug Please tick box if mandatory Relevant International tandard B 1363: PT.1: 1995 &B 1363: PT.2: 1995 for 3 pin rectangular type 13-Amp plug Mains Plug Configuration Extent of Alignment- - Diagram of Mains Plug Configuration- M 1577:2003 for round type 15-Amp plug M 1578:2003 for 2 pole plug with supply cord (max2.5a) BEN 50075:1991 2pole plug 400 Volts 50 Hz - - - - - Three phase tolerance +10%-6% ±1% Page 47 of 50
VIII. OTHER INFORMATION CUTOM (PROHIBITION OF IMPORT) (AMENDMENT)(NO. 7) ORDER 2015 JADUAL PERTAMA/FIRT CHEDULE (Goods the import of which is absolutely prohibited) (1) (2) (3) Item No. Description of goods ection/chapter/heading/ ubheading AHTN 2012 Country Ministry/ Department/ tatutory Body (For Reference only) 14 Liquid-filled type electric heating bag, cushion, pillow, pouch or pad using alternating current (AC) or AC and direct current (AC/DC) as follows: 8516.79 900, 9404.90 000 8516.79.90 00, 9404.90.90 00 All countries Energy Commission (i) with 2-pin inlet filled with liquid; or (ii) with 2-pin or 3- pin inlet without liquid (empty) Page 48 of 50
CUTOM (PROHIBITION OF IMPORT) (AMENDMENT)(NO. 7) ORDER 2015 JADUAL KEEMPAT/FOURTH CHEDULE BAHAGIAN II/PART II (Goods which may not be imported into Malaysia except conforming to the Malaysian tandard and/or other standards approved by the Malaysian Authorities and in the manner provided and does not apply to the free commercial zones) (1) (2) (3) (4) (5) Item No. Description of Goods Chapter/ Heading/ ubheading H2012 (9 digit) H2012 (10 digit) Country Manner of Import 13. Liquid-filled type electric heating bag, cushion, pillow, pouch or pad filled with liquid, using 3-pin inlet alternating current (AC) or AC and direct current (AC/DC) 8516.79 900, 9404.90 000 8516.79.90 00, 9404.90.90 00 All countries That the import is accompanied by a letter of approval issued by the Energy Commission in the case of Peninsular Malaysia and abah, or the equivalent counterpart in the case of arawak, certifying that the specified domestic electrical apparatus conforms to the Malaysian tandard or International Electrotechnical Commission (IEC) standard Page 49 of 50
IX. CONTACT PERON Country MALAYIA Contact Person and Address Mr. Mohd Elmi bin Anas Director, Department of Regulatory Electrical afety, Energy Commission No.12, Jalan Tun Hussein Onn, Presint2 62100 Putrajaya. Contact no:(603) 8870 8583 Fax no: (603) 88888652 Email: elmi@st.gov.my Website: http://www.st.gov.my Ir. Fairus bt Abd Manaf Head,Unit of Electrical Equipment Department of Regulatory Electrical afety, Energy Commission No.12, Jalan Tun Hussein Onn, Presint2 62100 Putrajaya. Contact no:(603)8870 8605 Fax no: (603)88888652 Email: fairus@st.gov.my Website: http://www.st.gov.my Page 50 of 50