EXPLORER 62' SPECIFICATIONS 1. PRINCIPAL PARTICULARS Length of overall 63 9 ( 19.44M) Length of water line.. 53'8" (16.35M) Beam O.A... 16'5"(5M) Draught 5 6 (1.67M) Displacement 32T Water Capacity.390 U.S. Gallons Fuel Capacity 1,540 U.S. Gallons Range Approx. 600-1000 miles plus depending on engines selected Main Engines: 2 X Cummins engines, model no. QSB6.7-550HO(24V) with ZF280A. One 4 vessel view + four sets of analogue gauges + ETS controls from Cummins ( Plus 2 x PTO for stabilizers) Generator: 1 X Onan of 22.5 KW 220V 50 Hz. Including sound shield, water & gas seperator, circuit breaker and meter controls on the generator and lower helm station for start/stop, engine hours volts etc. Stablizer: Wesmar RS700 Electronic Gyro Stablizer System Bow Thruster: Wesmar Vortex V2-12H @25hp Dual Prop Bow Thruster Stern Thruster: Wesmar Vortex V2-12NS @ 25hp Dual Prop Stern Thruster 1
2. GENERAL CONSTRUCTION 1.White Gelcoat 2.Hull, main deck, house & fly bridge molded fiberglass. Sandwich core for deckhouse and fly bridge 3.Hull with foam cored bulkheads 4.Hull and deck to be bonded in accordance with good shipbuilding practice 5.FRP Fuel and fresh water tanks with baffles and cleaning manholes 6.Teak cap rails with teak oil 7.Rounded frameless window with safety glass (grey) (no tint for front and side window in lower helm) 8.Four windows to be opening (sliding) including galley window with inside mosquito screens 9.13 ea stainless steel port holes in the hull, mosquito screens to be supplied 10. 2 ea oval port holes in cabin trunk 11. Cabin Headliner in cream vinyl, removable with 3M Velcro 12. One deck hatch on main deck for VIP cabin from Taiwan (Manship) ) with ocean air screen 13. Areas of stress such as cleats, fairleads, anchor windlass, etc to be suitably strengthened in accordance with good boat building practice 14. All holes cut into the bulkheads for hoses/wiring etc to pass through shall have a well rounded rubber grommet to protect wiring and hoses etc. This also applies to the ceiling throughout the boat 15. FRP rub rail 3. General (Accommodation & Interior) 1.Teak paneling and carpentry in all spaces 2.Flush cabinetry with new detailing throughout 3.Teak & Holly flooring throughout except engine room & crew cabin & showers 4.Soft vinyl (cream color) headliners with padding Removable panel type attached to the ceiling with 3M Velcro 5.High quality 70% gloss varnish for interior finish, high gloss fiddles and counter tops 6.Good quality door locks throughout from Timage 7.Switch and AC outlets from VIMAR 8.Interior fabrics Ultraleather/leather (only four choices for leather is STD), exterior cushions: Sunbrella. Standard curtain and mattresses fabric included in the price. 9.Suitable access hatches in forward accommodation to access all areas of the bilges. Automatic DC lighting to be supplied to all bilge areas where there is an access hatch 10. All furniture including beds, tables, sofas etc are to have smooth rounded corners and all the cabinet doors and drawers to be flush style with new styling 11. Air-conditioning outlets 12. Double wall style for all saloon windows etc 13. All doors to be properly secured in open position 2
4. Main Deck 1.F.R.P. Swimming platform with teak 2.Teak in the aft cockpit and a long both side decks to the first steps. Non skid (small diamond pattern) FRP foredeck 3.Armstrong telescopic slide-out ladder 4.Two FRP Transom doors 5.Boarding bulwark doors for Port & Starboard 6.Use the new bulwark door handles with the press button 7.Transom door and bulwark doors SS finished 8.Twin stainless steel bow rollers 9.Muir anchor winch (HR4000HYD) to be controlled from three stations. SS foot switches for up/down next to Bow locker. ( also add Chain stoppers ) Lower helm station and fly bridge helm station to have MUIR auto anchor chain counters. 10. ULTRA 316 s/s anchor 45 KG (99 LBS) with swivel 11. Fresh & Salt water wash down bow and aft deck, and upgrade both with quick release deck fitting 12. Teak bow & stern staffs 13. 100 Meters galvanized anchor chain (13mm) 14. One Ice FRP box on aft deck with drain 15. 1 1/4 316 stainless steel stanchions highly polished with SS hex screws 16. Hot and cold transom shower in aft deck 17. Dockside water connection (Par) 18. Four shore power connections Two in aft deck locker Two next to starboard pilot house door 19. All fuel oil and fresh water inlets to be recessed into superstructure 20. Sufficient Stainless steel fairleads and cleats - 2 bow, 2 mid ships and two aft 21. Suitable scuppers/drains 22. FRP stairs from aft deck to fly bridge with teak. Hella LED courtesy lights fitted to each step 23. Engine air intake port and starboard amidships on the superstructure 24. One hatch on portside of cockpit to crew cabin, should be big enough for the washer/dryer. Stainless steel steps with teak steps. 25. Hella LED lights for side decks & cockpit and under fly bridge / hard top (14EA) Hella LED courtesy lights for the two steps amid ships port & starboard, fly bridge, port/starboard bow coaming to light up anchoring arrangement, and back of transom (total 23ea) 26. Stainless steel fender holders for four fenders in crew cabin 27. Push knobs for all drawers throughout the interior from Seaworld 5. Fly Bridge 1.Non skid on Fly bridge (small diamond pattern) 2.Helm station in the middle 3.Standard full engine instrumentation and alarms and controls (see Main Engines ) 4.Storage in fly bridge brow portside 5.Hydraulic steering (hynautic) 6.Teak steering wheel 7.FRP hard top with stainless steel supports port & starboard 3
8.2 ea SS handrails under hardtop 9.Hella dimmerable LED spot lights under the hard top (5ea) 10. Hella LED red night lights under hardtop with dimmer switch (4ea) 11. Compass (Ritchie) 12. Stainless steel windshield with tinted lexan or acrylic 13. Upgrading fly bridge winshield 14. Hella LED navigation lights 15. FRP seating as per drawing with Hella LED courtesy lights (4ea) 16. FRP wetbar with sink and electric BBQ ( Dometic SMEV) plus one Dometic CR1110 fridge with hinged top 17. Plastic grating for inside all exterior seatings 18. Two FRP tables with stainless steel legs 19. White vinyl cushions (removable) with foam 20. Fly bridge re-enforced for ADC davit ADC 042 450kg (manual luff and manual slewing) 21. Two helm chairs (Aritex) 22. Sliding stainless steel hatch from aft deck to fly bridge (Aritex) 23. Opening stainless steel hatch for access from fly bridge to pilothouse 24. 1 1/4 SS 316 high polished stanchions 25. Suitable internal water drainage 26. Jabsco JABSCO#60080-0024, single station control 27. Explorer lighting logo from Aritex 28. 6ea cup holders with Binoc holders each side of flybridge 29. SS dinghy cradle 30. Fusion system (MS-IP700 x 1 + MS-FR602 x 4 + MS-WR600 x 1) 6. Lower Helm station 1.Indigo blue Ultraleather cover for all helm 2.Teak steering wheel 3.Complete engine instrumentation and alarms and controls 4.Overhead electronics console above helm station with custom mimic panel 5.Hydraulic trim tabs from Bennett with dual rams(bennett#5412) 6.Electric air horn with twin trumpets in the middle of PH ceiling 7.1 DC outlet + 2 AC outlets 8.Three electric windshield wipers and washers (Exalto with single panel) 9.Hydraulic steering (Hynautic) 10. 24V / 220 V wiring system throughout, switchboard with circuit breakers (AC & DC panel) Volt amp meters etc. Wiring to be color coded and numbered. Four spare circuit breakers for AC & DC 11. Fixed windows forward, clear safety glass 12. Compass (Ritchie) 13. Marine Tech lower helm seat high back 14. Curved stairway down to accommodation with step lights, and one ceiling light above 15. Wema fuel and water gauges 16. 2 ea cup holders on lower helm 17. 4 ea Hella LED red night lights with dimmer switch 18. 7ea Hella LED spot lights in ceiling with dimmer switch 4
7. Saloon 1.Built in L shaped settee with leather trim on all interior sofas (Buyer s choice of color) 2.S/S legs Hi-Lo with slide form Marine Tech 3.Starboard side cabinet with electronic controlled Manship TV lift with 42 plasma TV (Sony, or Samsung etc) 4.Bose Life style 235 with speakers in saloon ceiling 5.Access door to aft saloon to be Stainless steel (Aritex) 6.Aritex side sliding doors 7.Overhead spot lights to be 24V spot lights by Hella LED dimmerable (21ea, including galley) 8.4 ea Prebit LED W 2 wall lights 9.4ea AC outlets, 2ea in saloon, 2ea inside stb side cabinet 10. Norcold fridge (NORCOLD#EV-0061) fitted under internal stairs to fly bridge 11. U-Line ice maker (SS98-11) fitted under internal stair to flybridge 8. Galley 1.Staron counter top with rounded/curved end 2.Galley faucet 3.Miele 4 burner hob 4.Miele Convection oven 5.Fisher & Paykel single drawer Dishwasher DD60SDFX6 6.2 ea AC outlets Vimar 7.Double stainless steel sink with cutting board 8.Overhead locker for storage cabinet with rounded/curved end and 2ea ceiling lights 9.Galley cook hood blower Smeg#KSEC61X 10. Fittings for cups / plates and crockery Etc. 9. Port Guest Cabin 1.Two single berths with night stand 2.Cedar lined hanging locker with automatic light 3.Two Hella LED reading lights 4.5 ea Hella ceiling lights 5.Mattresses 6 foam, fabric covered 6.2ea AC outlets + 1ea TV antenna outlet 7.Bevelled mirror with shelves and table if bed not to join together 8.LED rope light underneath berths 9. Three portholes 10. VIP Guest Cabin 1.Island bed LED rope lights underneath berth 2.Mattress 8 foam with fabric covered 3.Two 24v Hella LED reading lights 4.6ea Hella ceiling lights 5.Push knobs for cabinets and drawers (Manship) 5
6.5ea AC outlets + 1 antenna outlet 7.220V Samsung TV 16 or 20 TV with DVD 8.Two hanging lockers with cedar lined with automatic light 9.Ocean air combi screen in forward cabin 10. Mirror on the forward bulkhead 11. Four portholes 11. Master Cabin 1.Queen size bed with one big drawer fitted under, LED rope light underneath berth 2.Mattress 8 thick foam, fabric covered 3.24V/220V Samsung flat screen TV 26 with DVD or equivalent 4.Clarion CD/Radio stereo/speakers 5.Cedar lined wardrobes with automatic light (Hella LED) 6.Two Hella LED reading lights either side of the island bed 7.4ea AC outlets + 1 TV antenna outlet 8.Desk/vanity, mirror underneath table top; 2 ceiling lights above 9.Two larger portholes (10 x 24 ) with screen 10. Ceiling treatment with 3ea spot lights and rope light 11. 6ea Hella spot lights in ceiling 12. Ultraleather headboard 13. Install 2ea 50AMP galvanic isolator in hanging locker 12. Master Ensuite Head 1.Teak interior walls, floating mirrored ceiling with high gloss teak grating 2.Safety shower door with frosted glass 3.Staron counter top with clear glass sink and faucet,two ceiling lights above 4.Mirror (bevelled) 5.Shower and sink faucet 6.1ea ceiling light in shower 7. High gloss teak grating in shower 8.Tecma fresh water flush head 9.Three way valve for direct discharge/deck or to holding tank 10. Exhaust blower from Smith s UK 11. Push knobs for cabinets/drawers (Manship) 12. 1 ea Vimar AC outlets 13. Toilet fittings 14. Granite floor 15. Travertine floor in head 16. Two larger portholes (10 x 24 ) 17. Teak door 13. Starboard Guest Head 6
1.Teak interior walls, floating mirrored ceiling with rope light and two ceiling lights 2.Safety shower door with frosted glass 3.Staron counter top with clear glass sink and faucet,two ceiling lights above 4.Mirror (bevelled) 5.Shower faucets 6.1ea ceiling light in shower 7.High gloss teak grating in shower 8.Tecma fresh water flush head 9.Three way valve for direct/deck discharge or to holding tank 10. Exhaust blower from Smith s UK 11. Push knobs for cabinets and drawers (Manship) 12. Two Hella LED spot lights for sink 13. Toilet fittings 14. Travertine floor in head 15. Two portholes 16. Teak door 14. Crew Cabin 1.Two single berths 2.Bosch washer / dryer installed in crew cabin 3.1ea of 9 blower 4.6ea of ceiling lights 5.Two portholes 6.Tecma head fresh water flush with anti-siphon 7.Shower faucet 8.Sink and faucet 9.Three way valve for direct or holding tank or deck to be conveniently placed 15. Engine room / Machinery systems 1.Engine exhausts under water with FRP muffler 2.Groco internal raw sea water strainers (Large) 3.Twin Racor fuel filters with gauges for main engines 4.One Racor fuel filter for generator 5.Aquamet shafts 17 6.P.Y.I dripless stern glands 7.Heavy duty bronze underwater brackets with cutlass bearings 8.Propellers 4 bladed (Hung Sheng S class) 9.Good quality exhaust from Smith UK 10. Hynautic Hydraulic steering 11. Manship moisture eliminator and air intake vents 12. Superior engine room sound proofing material - foam & lead 13. Teak in the middle of engine room floor, grey rubber for the whole engine room and crew cabin, teak slat as low as possible 14. White Aluminum perforated sheets to cover all bulkheads and fuel/water tanks etc 15. Five automatic Rule electric bilge pumps. Engine room bilge pumps high water alarm 16. Manual bilge pump (TMC) 7
17. Stainless steel fuel manifold & fuel return manifold 18. Four FRP fuel tanks with baffles (to be tested to 5 PSI) in engine room 19. Two FRP water tanks with baffles (to be tested to 5 PSI) under master & guest cabin berth 20. Sight gauges, self closing cocks and tank vents fitted to fuel and water tanks 21. Fuel tanks to have cross over valve 22. Black rubber fuel lines (CE approved) 23. Blue for cold fresh water 24. Red for hot fresh water 25. Black with blue stripe plastic for sea water 26. Cummins ETS electronic engine controls 27. Sea cocks on all through hulls below water line (BRONZE good quality SEACOCKS) 28. Double hose clamps on all pipes 29. 28 gallon hot water tank 30. Pressurized fresh water system (PAR WITH COMBINED PRESSURE TANK) 31. 2 x 200amp 24 V AGM battery for generator starting to be housed in FRP box & securely fastened 32. 2 x 200amp 24 V AGM batteries for each engine starting to be housed in FRP box securely fastened 33. 6 x 200amp 24 V AGM batteries for house to be housed in FRP box & securely fastened. 34. All the batteries to be security fastened with SS strap 35. Motorized Battery disconnect switch 36. Battery parallel switch to combine house batteries to engine starting batteries 37. Mastervolt charger 24/60-3 38. Mastervolt combi inverter charger 24/2500-60 39. Copper bonding throughout 40. FRP Rudder tubes 41. Stainless steel rudder blades (encapsulated in FRP) 42. Fresh water outlet with hose forward bulkhead of engine room 43. Tool cabinet 44. FRP drip tray under engine 45. FRP sewage holding tank with macerator pump for dockside or overboard discharge 46. Upgrading SEALAND#309-310002,SANIGARD HOLDING TANK VENT FILTER, 5/8 47. Seven Hella LED DC lights in engine room and two AC lights 48. 24V sump pumps for each shower using Whale shower sump pump system 49. All pipings are to be securely supported and braced to prevent damage by vibration etc 50. Stainless steel safety guards around both engines 51. Stainless steel engine mounts (highly polished) 52. Oil Reverso 24 V DC fitted for both main engines & the Generator 53. Exhaust alarm for engines 54. One door with glass to engine room 16. Electrical System 1.All wiring to be double sheathed, conduited and numbered on the control panel for wiring 2.220V AC and 24V DC cables to have distinctive color code for easy identification & numbered 3.All cables rating are to be in excess of the maximum load current 8
4.RCD and isolation switch fitted all 220V appliances in engine room and crew cabin 5.Electrical panel to have device for interlock between shore supply connection and the generator supply 6.BEP main switch panel 7.Four units split type reverse cycle marine air-conditioning systems from Dometic 8.2X 16.000 BTU for main saloon 9.1 X 16.000 BTU for pilot house/galley 10. 1 X 12.000 BTU for master cabin 11. 1 X 16.000 BTU for guest cabins (to be shared) 12. All electrical AC sockets to be Vimar 13. All circuit breakers to be of adequate size for the application 14. The boat shall be grounded throughout including all sea cocks etc. 15. All electrics to meet current Australian regulations 17. Navigation (Optional ) 18. Fire Fighting Equipment Automatic engine room fire fighting system (SEAFIRE#NFD1200MA) 19. Life Saving Equipment (Dealer optional) 20. Miscellaneous 1.Zinc anodes on rudders, shafts and transom and trim tabs 2.Emergency tiller securely fastened 3.International primer and Black anti-fouling 2 coats 4.Black boot stripe 5/6 with 1 gap and then the black anti foul All weights & measurements are approximate The builder reserves the right to change the specification without prior notice 9