Operation Instructions FULLY AUTOMATIC WASHING MACHINE XQB22-(AUS)22G The machine is for cold water connection only
CONTENTS PARTS IDENTIFICATION FUNCTIONS OF OPERATING SWITCHES SAFETY PRECAUTIONS INSTALLATION WASHING PROCEDURES WASHING PROCEDURE CHART INDICATION OF ABNORMITY POWER VOLTAGE TUB CLEANING PROGRAM TROUBLE SHOOTING MAIN TECHNICAL PARAMETERS 1 2 3 4 5 6 6 6 7 8 8
PARTS IDENTIFICATION ACCESSORIES Inlet Hose 1pc Upper drain hose 1pc
FUNCTIONS OF OPERATING SWITCHES POWER SWITCH Power supply is turned on by pressing down the button, and washer is in a mode of normal washing; and turned off by another press. After washing,power switch will spring up automatically to cut off power supply. WATER LEVEL SELECTOR Secelt the water level according to the capacity or quantity of clothes to be washed: "High","Medium", "Low". To increase the water level atter the set level has been reached,first set the switch to "RESET" and then immediately turn back WATER LEVEL to the desired level position thus the desired level can be obtained. MEDIUM HIGH LOW ON OFF POWER RESET WATER LEVEL START/HOLD When power is on, to start the machine, the button of [START/HOLD] must be pressed(the working indicator glitters)first. To hold the operating machine, press the button again, at which the working indicator turns from a glitter into a normal lighting.to renew its operation, press it another time. PROCESS SELECT If the full cycle of wash, rinse is not entired, the desired process can be selected by the key of PROCESS SELECT to choose WASH WASH-RINSE RINSE- SPIN SPIN SOAK-WASH-RINSE- SPIN SOAK-WASH SOAK- WASH-RINSE and so on. Lamps will be glittering when the washer is operating in any process. PROGRAM SELECT NORMAL: is suitable for washing the clothes of cottons linens synthetics fabrics GENTLE: is suitable for washing silks knits and soft clothes. TUB CLEANING: is used for cleaning the tub regularly.
SAFETY PRECAUTIONS Power Line *When take off the plug, be sure to hold the plug and not to pull the power line. *Do not put heavy articles on the power line or have it pressed by machine parts. *User should not replace power line by himself. Caution for Rotating Tub Donot put your hand into the rotating tub. Hot *Keep any hot articles or comburants away from the washer, do not put them on its top, because there are plasthetic parts inside the washer. Unwashable Clothes * Washing of clothes stained with flammable or volatile fluids is strictly prohibited. * Donot use organic solutions. No Splashing the Switch * Donot wash the machine, especially the electric parts ( may cause a failure or an accident). * Donot put the washer in a wet place. Measures After Washing * Take off the power plug. * Turn off the water tap. * Never to pile articles on the washer. * Keep inflammable or explosive matters away from the washer, Donot Let Children Climb up the Washer * Do not let a child climb up or down into the tub. special cautions should be taken when the washer is used at home. Petroleum Product Organic Solution
INSTALLATION Installation of water inlet pipe Put the water inlet pipe(which has metallic filtering bag) screw on to the tap.
WASHING PROCEDURES 1 2 ON OFF >750mm 1. First loose the adjust foot knob, place the washer evenly and stably,and tighten the knob. 2. Connect with the water inlet hose, and turn on the water tap. 3. Insert the power plug into the power socket (with the earth lead properly connected). 4. Hang the upper drain hose on the pond. 5. Loosely put clothes wash into the tub ( be careful not to leave coins keys etc.hard articles in their pockets, in case they will damage the tub. 6. Put an appropriate amount of detergent into the tub, too much of it is both a waste and difficult to rinse. Please refer to the Table of Amount of Detergent. Note: The water will overflow when the height of the drain hose under 750mm. Press down the Power Button, the washer enters a mode of normal wash procedure. 3 POWER AUTOMATIC TURNOFF RESET HIGH MEDIUM Select a proper water level based on the quentity of clothes.(the washer will not start before water reaches the set level.) 4 5 LOW START HOLD WATER LEVEL PROCESS SELECTION: If the full cycle of wash, rinse and spin is not entired,the desired process can be select (please reference to Functions of operating switches PROGRAM SELECTION: REGULAR: for cottons,linens,synthetic fabrics. GENTLE: for silks,knits and soft clothes. TUB CLEANING: use this program to clean the tub regularly. The machine starts to work on pressing down START/HOLD button. As the washer finishes washing,the buzzer buzzes and the power switch cuts off power supply automatically, the REGULAR light remain indicating.
WASHING PROCEDURE CHART Abnormal spin INDICATION OF ABNORMITY If the clothes to be spun have been couected or crowded on one side of the Uib. the tub will b& unbalanced during rotation. The microcomputer will detect the unbalanced condition and correct it with the following operations: Water filling rinse(1min.) Drain spin. However, if the unbalanced condition can not be eliminated by consecutively repeating three times the above operations, all the three indicating lamps of "PROCESS SELECT" will begin blinking on and off si multaneously and the buzzer will sound to indicate an abnormity. Open the lid and redisiribute the clothes (making it being distributed evenly or uniformly around the tub inside) in this case. Abnormal drain The microcomputer will determine the required drain time according to the drainage conditions. However, if water in the tub can not be drained away in a preset time if the drain hose has not been lowered or by poor drainage or other problems. In this case, all three indicating lamps of "PROCESS SELECT " will be blinking on and off simultaneously and the buzzer will sound to indicate an abnormity. Open the lid and check if there is water in the tub or lower the drain hose. Close the lid, the machine will operate normally. Followings are not malfunctions At the end of draining, the machine will be iniermittem spinning ( the tub spinning speed Mil] increase and decrease ).This is not shelving a malfunction but a special design to smoothly rotate the tub from low speed to high speed. POWER VOLTAGE 1. Do not use the washer if power supply is abnormal. 2. This machine has protective function for high voltage, when the voltage is 270V 10V, the power will be cut off automatically. APPLICABLE WATER LEVEL, WASH CAPACITY AND AMOUNTS OF DETERGENT Water Level Wash Capacity Applicable Detergent The amount of detergent applicable would vary because of the difference in detergent quality.
TUB CLEANING PROGRAM Instruction to the tub cleaning program It will be adhere to wash powder's residue inside and outside the barrel because of the pollution and the problem of the water quality. It will take smelly and the drain will not be flowing. Otherwise, the adhering residue will take off during the wash process. And the clothing will be dirty. User should clean the tub monthly. The process of tub cleaning 1 2 Switch on the power. Select the [Tub Cleaning] program. ON OFF POWER AUTOMATIC TURNOFF Inlet water Rinse for 5 minutes 3 Press the [Srart/Pause] button. Drain water! Spin for about 4 minutes Inlet water! Gyration for about 5 minutes Rinse 2 minutes! Water inlet for about 10 secs. Drain water! Spin for about 4 minutes *1 The water adding from low water level in order. The impeller start to move. *2 The program is draining the water while spinning.! Please do not start the program continuously. 4 5 When the impeller start to move, take 200ml chloric bleacher into the washer.! At first water inlet, you should take about 200ml chloric bleacher.! Please do not put into clothes. Close the door lid. If the door open, the program will stop before spin and rinse. Completion of tub cleaning! After completion of tub cleaning, the buzzer will buzz continuously.
TROUBLE SHOOTING Fault Do not Operate Completely No Water Inlet Abnormal Drainage Items to Check * If a power failure. * If the plug inserted correctly into the power socket. * If the fuse burnt out. * If the power switch pressed. * If START / PAUSE button pressed. * If the set water level reached. * If a water supply cut-off or an under water pressure. * If the water inlet hose connected properly, and the tap turned on. * lfthe filter net of the intake valve blocked by foreign matters. * If the water drain hose is placed very high. * If the end of the water drain hose is sealed in pond. * If the internal rubber seal ring of drain valve is blocked by dirt. No Spining * If the washer placed unlevelly or tiltingly. * If the clothes pressed to one side of the tub, or too many clotlies placed. * If the lid closed. MAIN TECHNICAL PARAMETERS Power 240V~/50Hz Working Water Pressure O.O3MPa-1MPa Input Power 280W Gross Weight 18kg Norminal Wash Capacity 2.2 kg Washing Type Novel Water Flow Norminal Spin Capacity 2.2 kg Draining Type Upper Drain Overall Dimensions 438X438X695mm Dewaterb Type Spining If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. CAUTION: If this appliance is supplied from a cord extension set or electrical portable outlet device, the cord extension set or electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture.