4-WAY MULTIPOISE TWO-STAGE CONDENSING GAS FURCE Product Data A9801 Utilizing the extensive resources available to Payne, a new standard of excellence has been achieved with the model. The model is a unique 4 -way multipoise condensing furnace with features like no other product in its class. The builds on the many Payne successes in the furnace industry and establishes a new standard for all high -efficiency gas furnaces. FEATURES combines two heating stages to vary the amount of gas being used from low -heat to high -heat stage. The low -stage operation allows longer running periods, which helps maintain your most comfortable temperature, prevents drafts, reduces noise, and enhances the air quality of your home. During extreme cold, the high -heat stage will run to ensure that you are still comfortable. Highly Efficient ECM Blower Motor - The highly efficient ECM motor and Payne s control logic can help selected 13 - and 14 -SEER Payne Air Conditioners achieve added energy efficiency up to 1. SEER as compared to the Air -Conditioning and Refrigeration Institute s standard coil -only rating (A/Cs up to 3. tons) when paired with selected Payne evaporator coils. Primary Heat Exchanger & Secondary Heat Exchanger - The primary heat exchanger is corrosion resistant. The secondary heat exchanger is built with a patented lamination process that bonds a corrosion -proof lining of polypropylene to a heavy, galvanized steel shell. Hot Surface Igniter - It is capable of running at line voltage and does not require complex voltage regulators as do other brands. Adjustable Continuous Fan - Improves comfort all year long by allowing you to select the continuous fan speed right at the thermostat. Dehumidification - Reduces summertime humidity levels by nearly % over standard systems. 4 -Way Multipoise Design - Allows the model to be installed in an upflow, downflow, or horizontal orientation. Factory configured for upflow applications with only simple drain connection changes required for conversion to downflow or horizontal. Direct or Non -direct Venting - The can be installed as a Non -Direct 1 -pipe vent (except 140 size) or Direct 2 -pipe vent furnace. This provides added flexibility to meet diverse installation needs. Two -Speed Inducer Motor - This motor works with the inducer fan to optimize combustion efficiency and exhaust the flue gases out of the house. Soft Motor Mounts - These motor mounts help to absorb shock. 1
1 1 4" 14 1 2" (368mm) (32mm) 1" (2mm) 2-IN. COMBUSTION- AIR CONN GAS CONN 2-IN. VENT CONN (1mm) (13mm) (13mm) ENTRY SIDE INLET 23 1 4" SIDE INLET 26 16" (684mm) 26 1 4" (66mm) 24 1 2" (666mm) (6mm) (1mm) (6mm) (91mm) (684mm) CONDENSATE DRAIN TRAP LOCATION (DOWNFLOW & HORIZONTAL LEFT) POWER CONN ACCESSORY POWER ENTRY CONDENSATE DRAIN TRAP LOCATION (ALTERTE UPFLOW) (240mm) (22mm) (22mm) (0mm) CONDENSATE DRAIN LOCATION (UPFLOW) (0mm) 24 1 2" (2mm) (4mm) 2 8" (2mm) (83mm) 32 8" (829mm) 33 1 4" (84mm) CONDENSATE DRAIN TRAP LOCATION (DOWNFLOW & HORIZONTAL RIGHT) OR ALTERTE 1 2" (mm) (14mm) 18 1 4" (464mm) CONDENSATE DRAIN LOCATION (UPFLOW) DIMPLE LOCATORS FOR HORIZONTAL HANGING 28 1 2" 26 1 4" (24mm) (694mm) (66mm) 19" (6mm) (483mm) OUTLET 2-IN. COMBUSTION- AIR CONN 22 1 4" (6mm) BOTTOM INLET (4mm) GAS CONN POWER CONN THERMOSTAT ENTRY 2-IN. VENT CONN SIDE INLET 1" (2mm) (16mm) (21mm) (8mm) 39 8" (13mm) (11mm) (1mm) 13 16" 8" 16" 16" 11 16" 8-IN. DIA 1 2-IN. DIA GAS CONN 9 16" 26 16" 22 16" 13 /16" AIRFLOW A 13 D /16" OUTLET 1 2-IN. DIA 8-IN. DIA 2 9 16" 9 16" 1 16" 29 11 16" 13 16" 1 2-IN. DIA 8-IN. DIA 22 11 16" 11 /16" INLET E 11 /16" 24 3 16" NOTES: 1. Minimum return-air openings at furnace, based on metal duct. If flex duct is used, see flex duct manufacturerõs recommendations for equivalent diameters. 2. Minimum return-air opening at furnace: a. For 800 CFM 16-in. (406mm) round or 14 1 / 2 (368mm) x -in. (mm) rectangle. b. For 10 CFM -in. (08mm) round or 14 1 / 2 (368mm) x 19 1 / 2-in. (mm) rectangle. c. For 1600 CFM 22-in.(9mm) round or 14 1 / 2 (368mm) x 23 1 / 4-in.(91mm) rectangle. d. For airflow requirements above 1800 CFM, see Air Delivery table in Product Data literature for specific use of single side inlets. The use of both side inlets, a combination of 1 side and the bottom, or the bottom only will ensure adequate return air openings for airflow requirements above 1800 CFM at 0. W.C. ESP. DIMENSIONS --- IN. (MM) A D E 036060 1---1/2 () ---/8 (403) 16 (406) 036080 1---1/2 () ---/8 (403) 16 (406) 048080 1---1/2 () ---/8 (403) 16 (406) 0600 21 (3) 19---3/8 (2) 19---1/2 () 0601 24---1/2 (2) 22---/8 (81) 23 (84) 26 16" 22 16" 1 2-IN. DIA 1 2-IN. DIA THERMOSTAT 22 11 16" A08323 2
CLEARANCE TO COMBUSTIBLES 332-1 REV. B LIT TOP A08 D E S I G N Always Ask For C E R T I F I E D CERTIFIED Use of the AHRI Certified TM Mark indicates a manufacturer s participation in the program. For verification of certification for individual products, go to www.ahridirectory.org. 3
SPECIFICATIONS CAPACITY* Direct Vent (2 --- pipe) (Shaded capacities are specified on the rating plate) CAPACITY* Non---Direct vent (1---pipe) AFUE* Direct Vent (2---pipe) Nonweatherized ICS AFUE* Non ---Direct Vent (1 ---pipe) Nonweatherized ICS 036060 036080 048080 0600 0601 Upflow 0 000 000 600 00 Low Downflow 36000 000 000 600 00 Horizontal 36000 000 000 600 00 High Low High Upflow 6000 000 000 900 1100 Downflow 6000 000 000 900 1100 Horizontal 6000 4000 4000 900 1100 Upflow 36000 000 000 600 00 Downflow 36000 000 000 600 00 Horizontal 36000 48000 000 600 00 Upflow 6000 000 000 94000 1100 Downflow 6000 000 000 900 1100 Horizontal 6000 4000 4000 900 1100 Upflow 92. Downflow 91 Horizontal 92.1 Upflow 92.1 Downflow 90. Horizontal 91. Low 39000 00 00 6000 8000 Input Btuh { High 60000 80000 80000 0000 1000 CERTIFIED TEMPERATURE RANGE(F) High ---60 40--- ---60 ---60 40--- 16.---33) (22---38.) 16.---33) 16.---33) (22---38.) Low ---0 ---60 ---60 ---60 ---60 (11---2.) 16.---33) 16.---33) 16.---33) 16.---33) CERTIFIED EX STATIC PRESSURE (in. wc) Heating 0. 0. 0. 0. 0. Cooling 0.0 0.0 0.0 0.0 0.0 High Heat 40 1180 140 1890 6 AIRFLOW (CFM)} Low Heat 63 83 9 93 142 Cooling 0 40 16 163 192 ELECTRICAL Unit Volts --- Hertz --- Phase 1 --- 60 --- 1 Operating Voltage Range Min---Max** 4 --- Maximum Unit Amps 8.2 8.3 9.9.1.4 Unit Ampacity{{ 11 11 13.9 16.2 Minimum Wire Size 14 14 14 Maximum Wire Length (Ft / M)}} 33 (.0) 33 (.0) 28 (8.) 36 (11.0) 3 (.) MaximumFuseSizeorCktBkrAmps{{{ Transformer (24v) 40va External Control Power Available Heating 19 Cooling 3 Air Conditioning Blower Relay Standard CONTROLS Limit Control SPST Heating Blower Control (Off Delay) Selectable 90, 1, 0, or 180 seconds Burners (Monoport) 3 4 4 6 Gas Connection Size 1/2---in. (13 mm) NPT GAS CONTROLS Manufacturer White --- Rodgers 2---Stage Redundant Gas Valve Min. Inlet Pressure (in. wc) 4. (Natural Gas) Max. Inlet Pressure (In. wc) 13. (Natural Gas) Ignition Device Hot Surface BLOWER DATA Direct --- Drive Motor HP ECM --- X --- 13 1/2 1/2 3/4 1 1 Motor Full Load Amps 6.8 6.8 8.4.9.9 RPM (Nominal)---Speeds 0--- 0--- 0--- 0--- 0--- Blower Wheel Diameter x Width --- In. (mm) X X 11 X 8 11 X 11 X (24X18) (24 X 18) (29 X 3) (3 X 24) (3 X 24) Filter Size (In. / mm)---permanent Washable See notes at end of table. (1) 16 X 2 X 3/4 (406 X 63 X 19) (1) X 2 X 3/4 (08 X 63 X 19) (1) 24 X 2 X 3/4 (6 X 63 X 19) 4
SPECIFICATIONS (CONT) FACTORY---AUTHORIZED AND LISTED DEALER---INSTALLED OPTIONS Gas Conversion Kit --- Natural ---to ---Propane Gas Conversion Kit --- Propane ---to ---Natural Twinning Kit Downflow Base*** Vent Termination Kit (Bracket Only for 2 Pipes) Vent Termination Kit (Single Exit) Condensate Freeze Protection Kit Condensate Neutralizer Kit (Obtained thru RCD) Vent Exhaust Pipe External Trap Kit Door Gasket Kit Unframed Filter, Permanent Washable 3/4 (19 mm) 16 x 2 (406 x 63) Unframed Filter, Permanent Washable 3/4 (19 mm) x 2 (08 x 63) Unframed Filter, Permanent Washable 3/4 (19 mm) 24 x 2 (6 x 63) KGANP01AAA KGAPN41AAA N/A KGASB01ALL 2---in. (1 mm)---kgavt01bra 3---in. (6 mm)---kgavt01bra 2---in. (1 mm)---kgavt01cvt 3---in. (6 mm)---kgavt0801cvt KGAHT01CFP P908---0001 KGAET06ETK KGBAC011DGK KGAWF11UFR KGAWF1401UFR KGAWF01UFR *U.S.A. --- Gas input ratings are certified for elevations to 00 ft. (6 M). For elevations above 00 ft (6 M), reduce ratings 2% for each 00 ft. ( M) above sea level. In Canada, derate the unit % for elevations 00 to 400 ft. (6 to 132 M) above sea level. {Capacity and AFUE in accordance with U.S. Government DOE test procedures Effective November, 199. } SAirflow shown is with factory---supplied 3/4---in. (19 mm) washable filter(s). SFor air delivery above 1800 CFM, see Air Delivery table for other options. SAn airflow reduction of up to % may occur when using the factory---specified 4---/16---in. (1 mm) wide, high efficiency media filter. SFor best furnace efficiency when using the 4---/16---in. (1 mm) wide media filter, adjust the blower speed tap to near the mid---point of the rise range. **Permissible voltage limits for proper furnace operation. {{Unit ampacity = % of largest component s full load amps plus 0% of all other potential operating components (EAC, humidifier, etc.) }}Length show in measured one way along wire path between unit and service panel for maximum 2% voltage drop. ***Required for installation on combustible floors when no coil box is used, or when any coil box other than a CNPV, CAPV, CAP, or CAR cased coil is used. N/A --- Not Applicable ICS --- Isolated Combustion System
MAXIMUM ALLOWABLE PIPE LENGTH - 0 to 00 (0 to 6) 01 to 00} (6 to 914) 01 to 4000} (914 to 19) 0,000 1,000 0,000 1,000 0,000 1,000 TERMITION. 2-1/2 (64) one TERMITION. 2-1/2 (64)# 3 (6) 3 (6) no 3 (6) # 3 (6) 3 (6) # 3 (6) no 4 (2) no TERMITION. 4 no IN (mm)* 4 (2) no IN (mm)* 3 (6) no 3 (6) # 4 (2) no 4 (2) no (16.8) (1.) 40 (.2) 4 (13.) (1.) 0 (.2) 3 (.) 40 (.2) 3 (.) 2 (.6) 1 (.2) 3 (.) 14 (4.3) 63 (19.2) (3.) 6 (.4) 26 (.9) 9 (2.) (2.1) 66 (.1) 16 (4.9) 2 (.6) 16 (4.9) 2 (.6) 6 (1.8) 66 (.1) 63 (19.2) 6 0 (.2) 16 (4.9) 68 (.) 46 (14.) 33 (.1) 6 (19.8) 9 (18.0) 11 (3.4) 63 (19.2) 41 (.) 24 (.3) 8 (1.) 9 (18.0) 6 (1.8) 28 (8.) 1 (.) 8 (1.) 23 (.0) 14 (4.3) 66 (.1) 22 (6.) (1.) 38 (11.6) 6 13 (4.) 6 31 (9.4) 6 6
MAXIMUM ALLOWABLE PIPE LENGTH - CONT. 4001 to 000 (19 to 14) 001 to 6000 (14 to 1829) 6001 to 00 (1829 to 2134) 0,000 1,000 0,000 1,000 0,000 1,000 TERMITION. 3 (6) no 3 (6) # 4 (2) no TERMITION. 4 (2) no 3 (6) no 3 (6) # 4 (2) no TERMITION. 4 (2) no 3 (6) no 3 (6) # 64 (19.) 31 (9.4) 6 9 (18.0) 39 (11.9) 22 (6.) 46 (14.0) (16.8) (1.) 8 (1.) 26 (.9) 13 (4.0) 6 (.4) 40 (.2) 4 (16.) 21 (6.4) (3.) 33 (.1) (.8) 26 (.9) (.8) (.8) 11 (3.4) (.8) (.8) 14 (4.3) 60 (18.3) 41 (.) 29 (8.8) 42 (.8) 9 (2.) (16.8) 36 (11.0) 21 (6.4) 6 (.4) 3 (.) 4 (16.) 23 (.0) (3.) 29 (8.8) 0 (.2) 18 (.) 11 (3.4) 22 (6.) 48 (14.6) 1 (.2) (.8) 48 (14.6) 4 (14.3) 8 (2.4) 4 (14.3) 9 (2.) 4 (14.3) 13 (4.0) 38 (11.6) 2 (8.2) 68 (.) 31 (9.4) 8 (2.4) (.8) 33 (.1) 19 (.8) 63 (19.2) 24 (.3) 48 (14.6) 0 (.2) 21 (6.4) 68 (.) 8 (1.) 18 (.) 4 (14.3) 4 (13.) 16 (4.9) 6 (.4) 9 (2.) 11 (3.4) 4 (13.) 66 (.1) 48 (14.6) 6 (1.8) 64 (19.) See notes at end of table.
MAXIMUM ALLOWABLE PIPE LENGTH - CONT. 01 to 8000 (2134 to 28) 8001 to 9000 (28 to 2) 9001 to,000 (2 to 48) 0,000 1,000 0,000 1,000 0,000 1,000 TERMITION. 3 (6) no 3 (6) # 4 (2) no TERMITION. 4 (2) no 3 (6) no 3 (6) # 4 (2) no TERMITION. 4 no 3 (6) # 4 (2) no 4 (2) no (3.) 36 (11.0) 66 (.1) 2 (.6) 63 (19.2) 46 (14.) (2.1) 48 (14.6) 31 (9.4) 6 (19.8) 1 (.2) 8 (1.) 13 (4.0) 6 46 (14.) 19 (.8) 63 (19.2) 8 (2.4) (2.1) 1 (.) 41 (.) 14 (4.3) (2.1) 48 (14.6) 40 (.2) (3.) 60 (18.3) 38 (11.6) 9 (18.0) 38 (11.6) 41 (.) 46 (14.0) 40 (.2) 41 (.) 38 (11.6) 36 (11.0) 11 (3.4) 33 (.1) 23 (.0) 9 (18.0) (3.) 3 (.) 6 (1.8) 28 (8.) 60 (18.3) 4 (16.) 42 (.8) 1 (.2) 8 (1.) (2.1) 3 (11.3) (3.) 6 (1.) 3 (.) (16.8) 39 (11.9) 34 (.4) 34 (.4) 41 (.) 39 (11.9) 2 (.6) 3 (11.3) 3 (.) 34 (.4) 4 (13.) 21 (6.4) 4 (16.) 39 (11.9) 40 (.2) 2 (.6) (16.8) 13 (4.0) 3 (11.3) (1.) 38 (11.6) 14 (4.3) (1.) 3 (.) 33 (.1) 9 (2.) 1 (.) 31 (9.4) (2.1) 29 (8.8) 4 (14.3) 39 (11.9) 33 (.1) 34 (.4) 31 (9.4) 29 (8.8) 29 (8.8) * Disk usage --- Unless otherwise specified, use perforated assembly (factory-supplied in loose parts bag). # If one is stated, separate 2 halves of perforated assembly and use shouldered half. When using shouldered half, install screen side toward inlet box. Wide radius elbow. Vent sizing for Canadian installations over 400 ft (13 M) above sea level are subject to acceptance by the local authorities having jurisdiction. ---Not Allowed; pressure switch will not make. Elbows and pipe sections within the furnace casing and at the vent termination should not be included in vent length or elbow count. The minimum pipe length is ft (1. M) for all applications. Use 3-in. (6 mm) diameter vent termination kit for installations requiring 4-in. (2 mm) diameter pipe. NOTES: Do not use pipe size greater than those specified in table or incomplete combustion, flame disturbance, or flame sense lockout may occur. Size both the combustion---air and vent pipe independently, then use the larger diameter for both pipes. Assume two 4 elbows equal one 90 elbow. Wide radius elbows are desirable and may be required in some cases. 8
MAXIMUM ALLOWABLE EXPOSED VENT PIPE LENGTH - WITH AND WITHOUT INSULATION IN WINTER DESIGN TEMPERATURE AMBIENT* 060 080 0 1 WINTER DESIGN TEMPERATURE F (_C) MAX PIPE DIAMETER --- IN (mm) WITHOUT INSULATION WITH 3/8 IN. ( mm) OR THICKER INSULATION (---) 2 (1) 0 ( --- 18) 2 (1) 21 (6.4) --- ( --- 29) 2 (1) (6.0) (1.3) (---) 2 (1) (16.) (16.) 0 ( --- 18) 2 (1) (16.) --- ( --- 29) 2 (1) 16 (4.8) (16.) (---) 2. (64) 8 (1.6) 0 ( --- 18) 2. (64) 29 (8.8) --- ( --- 29) 2. (64) 14 (4.2) 6 (.4) (---) 2. (64) 40 (.1) 40 (.1) 0 ( --- 18) 2. (64) 38 (11.) 40 (.1) --- ( --- 29) 2. (64) 21 (6.4) 40 (.1) (---) 3 (6) 63 (19.2) 0 ( --- 18) 3 (6) --- ( --- 29) 3 (6) (3.6) (---) 3 (6) 0 ( --- 18) 3 (6) 38 (11.) --- ( --- 29) 3 (6) 19 (.) (---) 4 (2) 6 (19.8) 0 ( --- 18) 4 (2) 26 (.9) --- ( --- 29) 4 (2) (1.) 6 (19.8) * Pipe length (ft / M) specified for maximum pipe lengths located in unconditioned spaces. Pipes located in unconditioned space cannot exceed total allowable pipe length as specified in Table. Insulation thickness based on R value of 3. per in. 9
DOWNFLOW SUBBASE DIMENSIONS - IN. (MM) FURCE CASING WIDTH 1-1/2 () 21 (3) 24-1/2 (2) FURCE IN DOWNFLOW APPLICATION Furnace with or without Cased Coil Assembly or Coil Box Furnace with or without Cased Coil Assembly or Coil Box Furnace with or without Cased Coil Assembly or Coil Box PLENUM OPENING FLOOR OPENING A B C D ---1/8 (384) 18---/8 (43) 22-1/8 () 19 (483) 19 (483) 19 (483) 16-3/4 (42) ---1/4 (14) 23-3/4 (603) ---3/8 (18) ---3/8 (18) ---3/8 (18) HOLE NO. FOR WIDTH ADJUST --- MENT 3 2 1 *The plenum should be constructed 1/4---in. (6 mm) smaller in width and depth than the plenum dimensions shown above. LOCATING TAB 1 1 /4 (32 μμ) A PLENUM OPENING B D 1 2 3 4 LOCATING TAB FACTORY-SUPPLIED FIELD-INSTALLED INSULATION C 4 3 2 1 COMBUSTION -AIR PIPE FOR NON -DIRECT VENT (1 -PIPE) APPLICATION (SIZES 040 THROUGH 1 ) FIELD-SUPPLIED 2-IN. (1 mm) DIA. PVC 90 ELBOW COMBUSTION-AIR DISC (FACTORY-SUPPLIED IN LOOSE PARTS BAG) FIELD-SUPPLIED 2-IN. (1 mm) DIA. PVC PIPE LENGTH OF STRAIGHT PIPE PORTION OF COMBUSTION AIR INLET PIPE ASSEMBLY (IN.) CASING WIDTH A A 1-1/2 ( mm) 8-1/2 ± 1/2 (216 ± 13 mm) A911 21 (3 mm) -1/2 ± 1/2 (26 ± 13 mm) 24-1/2 (2 mm) ± 1/2 ( ± 13 mm) CONCENTRIC VENT FOR DIRECT VENT (2 -PIPE) APPLICATION (ALL MODEL SIZES) B IN. (MM) DIA PVC VENT/EXHAUST F E 1 3 /16 ( mm) C IN. DIA 11/2 (38 mm) D A B IN. (MM) DIA PVC INTAKE/COMBUSTION AIR KIT PART NO. A* B C D{ E F KGAVT01CVT 33--3/8 (848) 2 (1) 3--1/2 (89) 16--/8 (422) 6--1/4 (9) --3/4 (146) KGAVT0801CVT 38--/8 (98) 3 (6) 4--1/2 (114) 21--1/8 () --3/8 (18) 6--1/2 (16) *Dimension A will change accordingly as Dimension D is lengthened or shortened. {Dimension D may be lengthened to 60---in. (14 mm) maximum. Dimension D may also be shortened by cutting the pipes provided in the kit to --- in. ( mm) minimum.
AIR DELIVERY - CFM (WITH FILTER) RETURN---AIR SUPPLY SPEED EXTERL STATIC PRESSURE (in. wc) 0.1 0.2 0.3 0.4 0. 0.6 0. 0.8 0.9 1 (Gry) 14 1390 134 10 0 10 80 99 84 3(Blu) 40 10 114 10 40 9 9 860 90 036060 SIDE/BOTTOM 4(Yel) 90 980 93 80 800 66 90 1(Red) 900 83 80 63 6 0 4 33 0 2(Org) 80 6 0 380 0 --- --- --- --- --- (Gry) 1400 1360 132 8 40 1160 1 00 3(Blu) 1340 10 6 1180 113 10 96 036080 SIDE/BOTTOM 4(Yel) 119 1160 11 6 2 98 93 89 80 800 1(Red) 2 980 93 880 83 9 4 68 63 8 2(Org) 8 800 4 680 63 60 460 4 360 (Gry) 1 169 1690 16 16 80 40 1 146 14 3(Blu) 6 10 10 140 14 13 133 9 048080 SIDE/BOTTOM 4(Yel) 13 13 1180 113 9 9 2(Org) 1180 113 8 3 99 90 9 86 8 1(Red) 11 6 0 960 9 86 8 6 (Gry) 198 192 1890 180 19 1 1690 16 3(Blu) 18 1 1 1690 163 9 00 1460 14 0600 SIDE/BOTTOM 4(Yel) 80 1480 10 1380 1380 1340 8 3 118 2(Org) 1380 132 116 60 00 960 1(Red) 11 98 93 8 80 6 660 (Gry) 220 2 2 21 6 19 192 18 190 3(Blu) 21 8 1980 192 1880 18 1 1 16 0601 SIDE/BOTTOM 4(Yel) 1890 183 190 140 1690 1640 90 1480 1 1(Red) 1640 8 14 142 136 13 60 10 1140 2(Org) 14 13 1 1190 113 6 940 880 NOTES: * Airflow shown is with factory supplied 3/4---in. (19 mm) washable filter.*a filter is required for each return air opening. *An airflow reduction of up to % may occur when using the factory---specified 4---/16---in. (1 mm) wide, high efficiency media filter. *For best furnace efficiency when using the 4 /16---in. (1 mm) wide media filter, adjust blowerspeedtaptonearthemid---point oftheriserange. *For horizontal and downflow applications, use one side or bottom or bottom only as an airflow reference. 11
E Payne Heating & Cooling Systems D 3 W. Morris St. D Indianapolis, IN 431 Printed in U.S.A. Edition Date: 09/ Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. Catalog No: SS --- --- 0 Replaces: SS --- P9MXA --- 04