Surface Mount Ambient Light Sensor Surface Mount Ambient Light Sensor Features Closely respond to human eye spectrum Light to current with analog output Good output linearity across wide illumination ranges Low sensitivity variation across various light sources Operation temperature performance: -40 ~ +85 C Wide supply voltage range: 2.5V to 5.5V RoHS compliance M1708 Descriptions This product is a good effective solution for power saving of display of backlight of mobile appliances, such as the mobile phones, notebook and PDAs. Due to the high rejection ratio of infrared radiation, the spectral response is close to human eyes. Applications Detection of ambient light to control display backlighting Mobile devices-mobile phones, PDAs. Computing devices-tft LCD monitor for notebook computer Consumer devices-tft LCD TV, plasma TV, video camera, digital camera, toys Automatic residential and commercial management Auto contrast enhancement for electronics signboard Ambient light monitoring device for daylight and artificial light Device Selection Guide Part No. Chip Material Lens Color Silicon Water Clear TAITRON COMPONENTS INCORPORATED Tel: (800)-TAITRON (800)-824-8766 (661)-257-6060 Fax: (800)-TAITFAX (800)-824-8329 (661)-257-6415 Page 1 of 11
Absolute Maximum Ratings (Ta=25 C) Parameter Symbol Value Unit Supply Voltage VCC -0.5~6.0 V Operating Temperature Range Topr -40 ~ +85 C Storage Temperature Range Tstg -40 ~ +100 C Soldering Temperature Range Tsol 260 ±10 C Recommended Operating Conditions (Ta=25 C) Parameter Symbol Value Unit Operating Temperature Range Topr -40 ~ +85 C Supply Voltage VCC 2.5~5.5 V Electro-Optical Characteristics (Ta=25 C) Parameter Symbol Min. Typ. Max. Unit Condition Collector Dark Current ICEO ----- ----- 0.1 µa VCE=10V, Ev=0 Lux Collector-Emitter Saturation Voltage VCE(sat) ----- ----- 0.4 V Ic=2mA,Ev=1000 Lux IPH1 5 15 ----- µa VCE=5V, Ev=100 Lux ( Note.1) Light Current IPH2 50 150 ----- µa VCE=5V, Ev=1000 Lux ( Note.1) IPH3 140 520 ----- µa VCE=5V, Ev=1000 Lux ( Note.2) Photocurrent Ratio IPH3/ IPH2 ----- 3.5 ----- ----- VCE=5V, Ev=1000 Lux Saturation Output Voltage VO 4.5 4.6 ----- V VCC=5V, RL=7.5Kohm, Ev=1000 Lux (Note.2) Peak Sensitivity Wavelength λp ----- 630 ----- nm Sensitivity Wavelength Range λ 390 ----- 700 nm Rise Time tr ---- 0.11 ---- ms VCC=5V, RL=7.5Kohm Fall Time tf ---- 0.22 ---- ms (See Test Circuit) Notes: 1. White fluorescent light (color temperature=6500k) is used for light source. White LED is substituted in mass production. 2. Incandescent lamp, CIE standard illuminant -A/ 2856K, incandescent lamp. Page 2 of 11
Typical Electro-Optical Characteristics Curves (Ta=25 C) Fig.1 Light Current vs. Illuminance Fig.2 Output Voltage vs. Illuminance Illuminance (Lux) Illuminance (Lux) Fig.3 Spectral Response Fig.4 Light Current vs. Supply Voltage Relative Sensitivity (%) Relative Light Current Light Current Output (µa) Output Voltage (V) Wavelength λ (nm) Vcc (V) Page 3 of 11
Typical Electro-Optical Characteristics Curves (Ta=25 C) Fig.5 Light Current vs. Temperature Fig.6 LED Light Current vs. Illuminance Relative Light Current Light Current (µa) Temperature (ºC) Illuminance (Lux) Testing Circuit Note 1. The output voltage (Vout) is the product of photocurrent (IPH) and loading resistor (RL) 2. A right loading resistor shall be chosen to meet the requirement of maximum ambient light, and output saturation voltage: Vout (max.)=iout(max.) x RL Vout(saturation)=Vcc-0.4V Page 4 of 11
Package Outline Dimensions (Unit=mm) Note: All dimensions are in mm with tolerances = ±0.1mm Page 5 of 11
Carrier Tape Dimensions (Unit=mm): Loaded quantity 4000pcs per reel Note: The tolerances unless mentioned is ±0.1mm. Moisture Resistant Packaging Page 6 of 11
Reel Dimensions (Unit=mm): Page 7 of 11
Ordering Information PTAS P 1 F 1708 C H6 92 TR70 Lead Free Tape & Reel 7=7 reel 0=4,000pcs per reel Factory Location Code Height <=0.6mm Water Clear Size Code in mm Flat Top Convex Type PCB Type Phototransistor Ambient Light Label Format CAT: Ranks HUE: Peak Wavelength REF: Reference Page 8 of 11
Recommended method of storage 1. Do not open moisture proof bag before devices are ready to use. 2. Shelf life in sealed bag from the bag seal date: 18 months at 10ºC ~ 30ºC and 90% RH. 3. After opening the package, the devices must be stored at 10ºC ~ 30ºC and 60% RH, and used within 168 hours (floor life). 4. If the moisture absorbent material (desiccant material) has faded or unopened bag has exceeded the shelf life or devices (out of bag) have exceeded the floor life, baking treatment is required. 5. If baking is required, refer to IPC/JEDEC J-STD-033 for bake procedure or recommend the following conditions: 192 hours at 40ºC +5/-0ºC and < 5% RH (reeled/tubed/loose units) or 96 hours at 60ºC ±5ºC and < 5% RH (reeled/tubed/loose units) or 24 hours at 125ºC ±5ºC, not suitable for reel or tubes. Recommend Solder Profile 1. Soldering Condition 1.1 (A) Maximum Body Case Temperature Profile for evaluation of Reflow Profile. Note: Reference: IPC/JEDEC J-STD020D Page 9 of 11
Preheat Temperature Min (T smin) 150ºC Temperature Max (T smax) 200ºC Time (T smin to T smax) 60-120 seconds Average ramp-up date (T smax to T p) 3ºC/second max Other Liquids Temperature (T L) 217ºC Time above Liquids Temperature (t L) 60-100 seconds Peak Temperature (T p) 260ºC Time within 5ºC to Actual Peak Temperature: T p-5ºc 30 seconds Ramp-Down Rate from Peak Temperature 6ºC/second max Time 25ºC to Peak Temperature 8 minutes max Reflow Times 3 times Notice (1) When soldering, do not put stress on the devices during heating (2) After soldering, do not warp the circuit board. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. Page 10 of 11
Repairing Repair should not be done after the device have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the device will or will not be damaged by repairing. How to contact us USA HEADQUARTERS 28040 WEST HARRISON PARKWAY, VALENCIA, CA 91355-4162 Tel: (800)-TAITRON (800)-824-8766 (661)-257-6060 Fax: (800)-TAITFAX (800)-824-8329 (661)-257-6415 Email: taitron@taitroncomponents.com Http:// TAITRON COMPONENTS INCORPORATED TAIWAN BRANCH 6F., NO.190, SEC. 2, ZHONGXING RD., XINDIAN DIST., NEW TAIPEI CITY 23146, TAIWAN R.O.C. Tel: 886-2-2913-6238 Fax: 886-2-2913-6239 TAITRON COMPONENT TECHNOLOG SHANGHAI CORPORATION SUITE 1503, METROBANK PLAZA, 1160 WEST YAN AN ROAD, SHANGHAI, 200052, CHINA Tel: +86-21-5424-9942 Fax: +86-21-2302-5027 Page 11 of 11