Installation/Operation and Service Parts Manual

Installation/Operation and Service Parts Manual Rotary-type Conveyor Glasswasher Model: DFM7.5 Clockwise Rotation Issue Date: 9.7.17 Manual P/N 0514427 rev. B For machines beginning with S/N G160520081 3765 Champion Boulevard Winston-Salem, NC 27105 (336) 661-1992 Fax: (336) 661-1660 Toll-free: (800) 858-4477 2674 N. Service Road, Jordan Station Ontario, Canada L0R 1S0 (905) 562-4195 Fax: (905) 562-4618 Toll-free: (800) 263-5798 Printed in the USA

National Service Department In Canada: In the USA: Toll-free: 800/ 263-5798 Toll-free: 800/ 858-4477 Tel: 905/ 562-4195 Tel: 336/ 661-1992 Fax: 905/ 562-4618 Fax: 336/ 661-1660 email: service@moyerdiebellimited.com email: service@moyerdiebel.com ATTENTION: The glasswasher model no., serial no., voltage, Hz and phase are needed to identify your machine and to answer questions. Please have this information on-hand if you call for service assistance. COPYRIGHT 2017 All rights reserved Printed in the USA

Product Registration REGISTER YOUR PRODUCT to ACTIVATE YOUR WARRANTY. 4:34 PM 44% Three ways to register: Use your mobile device to scan the QR code located on the front panel of your machine or enter our URL http://www.moyerdw.us/df. Visit our website at: http://www.moyerdiebel.com/service/ for the USA http://www.championindustries.com/warranty-registration for Canada Use the FAX FORM on the next page.

PRODUCT REGISTRATION BY FAX COMPLETE THIS FORM AND FAX TO: (336) 661-1660 in the USA 1-(800) 204-0109 in Canada PRODUCT REGISTRATION CARD Model Serial # Date of Installation: Company Name: Address: Telephone #: ( ) --- Contact: (Street) Province Postal Code Installation Company: Address: Telephone #: Contact: FAILURE TO REGISTER YOUR PRODUCT MAY VOID YOUR WARRANTY IMPORTANT IMPORTANT

Revision History Revision Revised Serial Number Revision Date Pages Effectivity Description Revision History We reserve the right to make changes to this manual without notice and without incurring any liability by those changes. Equipment owners may request a revised manual, at no charge, by calling 1 (800) 858-4477 in the USA or by calling 1 (800) 263-5798 in Canada. 8.26.16 All G160520081 Released DFM7.5 version 1.9.17 25 All Changed shut-off assy part no. to P/N 0714437 9.7.17 37 All Changed item no. 24 P/N to 0514413 i

Limited Warranty LIMITED WARRANTY Moyer Diebel. (herein referred to as The Company), 3765 Champion Blvd., Winston-Salem, North Carolina 27105, and 2674 N. Service Road, Jordan Station, Canada, L0R 1S0, warrants machines, and parts, as set out below. Warranty of Machines: The Company warrants all new machines of its manufacture bearing the name "Moyer Diebel" and installed within the United States and Canada to be free from defects in material and workmanship for a period of one (1) year after the date of installation or fifteen (15) months after the date of shipment by The Company, whichever occurs first. [See below for special provisions relating to glasswashers.] Warranty registration must be submitted to Moyer Diebel within ten (10) days after installation either online on the Moyer Diebel website (http://www.moyerdiebel.com/service/) for the USA or http://www.championindustries.com/warranty-registration for Canada or by fax on the form provided in the front of this manual. If warranty registration is not returned to The Company within such period, the warranty will expire after one year from the date of shipment. The Company will not assume any responsibility for extra costs for installation in any area where there are jurisdictional problems with local trades or unions. If a defect in workmanship or material is found to exist within the warranty period, The Company, at its election, will either repair or replace the defective machine or accept return of the machine for full credit; provided; however, as to glasswashers, The Company's obligation with respect to labor associated with any repairs shall end (a) 120 days after shipment, or (b) 90 days after installation, whichever occurs first. In the event that Moyer Diebel elects to repair, the labor and work to be performed in connection with the warranty shall be done during regular working hours by The Company's authorized service technician. Defective parts become the property of The Company. Use of replacement parts not authorized by The Company will relieve The Company of all further liability in connection with its warranty. In no event will The Company's warranty obligation exceed The Company's charge for the machine. The following are not covered by The Company's warranty: a. Lighting of gas pilots or burners. b. Cleaning of gas lines. c. Replacement of fuses or resetting of overload breakers. d. Adjustment of thermostats. e. Adjustment of clutches. f. Opening or closing of utility supply valves or switching of electrical supply current. g. Cleaning of valves, strainers, screens, nozzles, or spray pipes. h. Performance of regular maintenance and cleaning as outlined in operator s guide. i. Damages resulting from water conditions, accidents, alterations, improper use, abuse, tampering, improper installation, or failure to follow maintenance and operation procedures. j. Wear on Pulper cutter blocks, pulse vanes, and auger brush. Examples of the defects not covered by warranty include, but are not limited to: (1) Damage to the exterior or interior finish as a result of the above, (2) Use with utility service other than that designated on the rating plate, (3) Improper connection to utility service, (4) Inadequate or excessive water pressure, (5) Corrosion from chemicals dispensed in excess of recommended concentrations, (6) Failure of electrical components due to connection of chemical dispensing equipment installed by others, (7) Leaks or damage resulting from such leaks caused by the installer, including those at machine table connections or by connection of chemical dispensing equipment installed by others, (8) Failure to comply with local building codes, (9) Damage caused by labor dispute. Warranty of Parts: The Company warrants all new machine parts produced or authorized by The Company to be free from defects in material and workmanship for a period of 90 days from date of invoice. If any defect in material and workmanship is found to exist within the warranty period The Company will replace the defective part without charge. DISCLAIMER OF WARRANTIES AND LIMITATIONS OF LIABILITY. THE COMPANY'S WARRANTY IS ONLY TO THE EXTENT REFLECTED ABOVE. THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED, TO ANY WARRANTY OF MERCHANTABILITY, OR FITNESS OF PURPOSE. MOYER DIEBEL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSE-QUENTIAL DAMAGES. THE REMEDIES SET OUT ABOVE ARE THE EXCLUSIVE REMEDIES FOR ANY DEFECTS FOUND TO EXIST IN THE COMPANY'S DISHWASHING MACHINES AND THE COMPANY'S PARTS, AND ALL OTHER REMEDIES ARE EXCLUDED, INCLUDING ANY LIABILITY FOR INCIDENTALS OR CONSEQUENTIAL DAMAGES. Moyer Diebel does not authorize any other person, including persons who deal in Moyer Diebel dishwashing machines to change this warranty or create any other obligation in connection with Moyer Diebel Dishwashing Machines. ii

Table of Contents Table of Contents Revision History... i Limited Warranty... ii Specifications...iv Installation... 1 Unpacking... 1 Utility Connections... 3 Chemicals... 4 Flow Diagram... 6 Quick Operation Guide... 7 Operation... 8 Assembling the Glasswasher... 8 Filling the Wash Tank... 8 Operating Instructions... 8 Cleaning...15 Daily Cleaning or after 8 hours of operation... 15 Weekly Cleaning or 56 hours of operation... 10 Troubleshooting...12 Service Replacement Parts...17 Electrical Schematic...42 iii

Specifications iv

Installation Unpacking Installation 1. Move the glasswasher to its permanent location. 2. Open the door and remove the box marked "LEGS". The box contains (4) 6" [152cm] screw-in legs. These legs are threaded tightly into the base of the machine. 3. Remove (2) 1/2-13 x 2" bolts holding the glasswasher to the pallet. 4. Lift the front door off the bottom hinges and set carefully aside. 5. The illustrations below show one method to install the legs without lifting the glasswasher completely off the pallet. NOTE: The installation of the dishwasher must comply with all local electrical, plumbing, health and safety codes or in the absence of local codes, installed in accordance with the applicable requirements in the National Electrical Code, NFPA 70, Canadian Electrical Code (CEC), Part 1, CSA C22.1; and the Standard for Ventilation Control and Fire Protection of Commercial Cooking Operations, NFPA 96. CAUTION: The glasswasher water inlet plumbing and the drain piping extend below the pallet. Use extreme care when moving the glasswasher to prevent damage to the glasswasher plumbing. Boxed Legs Drain Water Connections Remove the (2) pallet bolts holding the glasswasher to the pallet. Pallet Glasswasher plumbing connections extend below the pallet. Continued on the next page. 1

Installation Installation Unpacking (continued) 6. Use two people to move the machine in order to install the legs. 7. Have one person behind the glasswasher tilt it back as the person in front twists the machine to the right. This makes the front left leg mounting hole accessible. 8. Screw one of the legs tightly into place. Repeat this process for the remaining legs. 9. Lift the glasswasher off the pallet, and re-install the front door.. 10. Level the glasswasher front-to-back and side-to-side by adjusting the leg bullet feet in or out. 11. Compare the site utilities with the data plate specifications. If they agree, then proceed with the installation according to the diagrams on the next page. 12. Remove the packing material in the glasswasher and discard, then remove any protective film on the machine. Twist the glasswasher to the right, then to the left. TILT Tilt the machine back to clear plumbing connections. Twist the machine to the right until the front right leg mounting hole is accessible. Thread (1) leg in each corner of the machine base 1" 1½" 6"-7½" Level front-to-back and side-to-side Make sure to install the legs tightly. 2

Installation Utility Connections The installation of this machine must be performed by personnel who will follow all safety, electrical, plumbing, and sanitation codes. 4 6 ft. (1.5M) 25" [635] 1 HOT WATER CONNECTION: 140-160 F/60-71 C ½" IPS Flow Pressure 25-95 PSI [173-655 kpa] Install water shut-off valves and check-valves in the water inlet supply lines and as close to the machine as possible. 7¾" [197] 6¼" [156] Plan View 2 3 1 26-1/4" [667] 6¼" [156] 6¼" [156] 2½" [64] 2 COLD WATER CONNECTION: 75 F/24 C ½" IPS Flow Pressure 25-95 PSI [173-655 kpa] Install water shut-off valves and chack-valves in the water inlet supply lines and as close to the machine as possible. Front View 3 2 1 39" [991] 4¾" [121] 5½" [140] 3 DRAIN CONNECTION: Gravity 1-½" Tailpiece (slip-fit) Maximum drain flow 3 US gallons/min [11L/min]. 17¾" [451] 4 ELECTRIC CONNECTION: 208-230VAC/50-60Hz/1PH Min/Max 15A 6ft./1.5m flexible cord and plug supplied NEMA 6-15P electric outlet. Side View 39" [991] 1 2 3 6¼" [156] 7¾" [197] 12½" [318] 3

Installation Installation (continued) Chemicals Glassware cleaning chemicals 1. A qualified chemical supplier should supply liquid detergent, sanitizer and rinse-aid for the glasswasher. The glasswasher manufacturer does not sell glassware washing chemicals. 2. A chemical's formulation and strength vary depending on the chemical supplier; therefore, the specifications given below are approximations only. 3. The glasswasher has 3 built-in chemical dispensing pumps for Detergent - Sanitizer - Rinse-aid - Use a commercial grade non-chlorinated detergent specifically made for glasswashers. The recommended concentration of detergent should be.35% 2 types of sanitizer may be used. (5.25%) Sodium hypochlorite (chlorine bleach) to provide a minimum concentration of 50 ppm in the final rinse. The 50 ppm concentration must be checked using test strips to make sure the proper concentration is maintained. Iodophor (Iodine formulated with a rinse agent), to provide a minimum concentration of 12.5ppm in the final rinse. The 12.5 ppm concentration must be checked using test strips to make sure the proper concentration is maintained. Consult your chemical supplier for the proper type of rinse-aid to use in the glasswasher. Installing chemical supply containers and chemical pick-up tubes 1. There is enough space inside the lower compartment to hold 3 one gallon containers for detergent, sanitizer, and rinse-aid. The contents of each container must be marked clearly. 2. The glasswasher comes equipped with 3 gray tubes, called stiffener tubes, and tubing for each chemical pump. The tubing inserted in the chemical container has a strainer. 3. The outlet tubes from the supply containers to the chemical pumps are marked with color-coded labels, they are: RED - Detergent (DET) CLEAR - Sanitizer (SAN) BLUE - Rinse-aid (R/A) 4. Pull the stiffener tubes and chemical tubing forward and out of the compartment. Make sure the tubing is not tangled or kinked. 5. Insert the stiffener tube and pick-up tubing into its container and stow the supply containers in the lower compartment as shown to the right. R/A DET SAN RED CLEAR BLUE DETERGENT SANITIZER RINSE DET SAN R/A 4

Installation Priming the Chemical Injectors and Approximate Chemical Settings Each chemical injector can be adjusted using its prime button and concentration adjusting screw. These controls are located on the right side of the control box located in the lower compartment of the glasswasher. The white injector rotors are visible through the control box window. Push to prime Rotor Rinse-aid Sanitizer Detergent - + Turn CW to increase(+) CCW to decrease (-) R/A SAN DET Chemical Injector Prime and Concentration Controls NOTE: All of the chemical settings below are approximations. Consult a qualified chemical representative trained in the use of the test equipments required for taking samples and performing adjustments. 1. Priming the Pumps: Make sure the proper chemical pick-up tube is in its supply container, then push and hold the prime button until the detergent, sanitizer and rinse-aid feed tubes are full of chemicals. Release the Prime button. 2. Approximate Chemical Settings: The approximate chemical volume dispensed by the chemical injectors can be determined by counting the number of revolutions of the injector rotor. Detergent - 1 revolution in 1-second of the detergent pump rotor ~ 0.35% concentration. Sanitizer - 1 revolution in 5-seconds ~ 12.5 ppm of Iodophor or 50 ppm of chlorine. Rinse-aid - 1 revolution in 8-seconds ~ the median volume recommended. Turn the Injector Concentration screws clockwise to increase or counter-clockwise to decrease the volume of dispensed chemical. 3. The detergent chemical setting must be performed when the hot-water fill solenoid valve is open. The hot-water valve is open when the power switch is in the ON position during initial fill and when the detergent tank float assembly calls for hot water The sanitizer and the rinse-aid setting can be performed whenever the cold-water fill solenoid valve is open. The cold-water fill valve is open whenever the glasswasher power switch is ON and the conveyor is turning. A separate rinse-aid is not needed when Iodophor is used as a sanitizer. Turn the Injector Concentration Screw fully counter-clockwise until the rinse-aid injector rotor stops turning. 5

Operation Flow Diagram The diagram below shows the major components of the DFM7 glasswasher and the flow of water and chemicals during normal operation. 6

Operation Quick Operation Guide The glass washing machine is designed to automatically wash a wide variety of glassware. The glass washer consists of a wash section and rinse section. Glasses rotate on a conveyor through each section. A wash tank in the lower compartment holds heated wash water. The water level in the wash tank is maintained by a float and cam-operated switch. The wash tank water temperature is controlled by a heater and a thermostat. The rinse water is supplied from the cold water supply. Chemicals are automatically dispensed by built-in chemical pumps 1 Plug machine power cord into a 208-230VAC/60/1,15 A wall receptacle. Turn main power and water service ON. 2 3 4 Remove lower wash tank scrap screen. 1 8 2 3 7 5 Install the drain/ overflow tube into the drain located at the front of the wash tank bottom. Re-install the scrap screen removed in Step 2. 4 MIX 6 White Label Sanitizer 7 Red Label Detergent Blue Label Pull the chemical pick-up tubes out of the machine Colored labels I.D. each tube Place tube into its supply container. Rinse-aid 5 6 7 Make sure a glass is against the conveyor stop switch, Push the rocker switch UP to the ON position until the wash tank is full of water. Then, push and hold each chemical Prime button until chemical supply tubes are full. On Off Flush Prime Prime Prime R/A Sani Det. The incoming cold water supply temperature must be a minimum temperature of 75 F/24 C. Adjust the temperature of the incoming cold water temperature by opening or closing the mixing valve located between the hot water and the cold water solenoid valves. 8 MIX Place glassware on the conveyor. The conveyor stops automatically when when the clean glassware operates the conveyor stop switch. Check the cold water temperature gauge and the cold water pressure gauge as you adjust the mixing valve. The minimum temperature should be 75 F/24 C. The pressure gauge should read a flowing pressure of 4-6 psi/24-36 kpa. Check the wash tank temperature gauge for 140 F/60 C- 160 F/71 C. Pressure Temperature Wash Tank Heat 7

Operation Operation Assembling the Glasswasher 1. Make sure the power switch is in the OFF postion. 2. Install the wash arms and rinse spray arms. The spray arms have locating notches in the end of each arm. Push the spray arm straight into the hub. Do not twist. 3. Install the conveyor assembly as follows: Insert the conveyor into the wash chamber keeping the rear raised. Pull the conveyor forward until it meshes with the drive gear located at the front of the wash chamber. Continue to pull the conveyor forwards as you lower it on the pivot. 4. Install the stainless steel cylinder in the center of the conveyor. 5. Install the conveyor shut-off assembly (plexiglass divider). 6. Install the right and left hand tray. 7. Install the curtain assembly. 8. Install the upper and lower scrap screens. 9. Intsall the standpipe in the detergent tank. Twist slightly to make sure it seats securely in the drain. 10. Install the drain tray/waste collector (if equipped). Make sure the drain fitting is secure. 11. Make sure the chemical supply containers are full. 12. Close the door. Filling the Wash Tank 1. Ensure that the overflow/drain tube is in place in the detergent tank. 2. Flip power on-off/flush switch to the "ON" position. The water will fill until the proper water level is reached. 3. The water temperature is controlled by a tank heater and an adjustable thermostat. The thermostat should be set for a minimum of 140 F/60 C. Operating Instructions 1. Ensure that the chemical supply containers are full. 2. Detergent is fed into the tank in controlled amounts by the detergent dispensing pump. Use detergent at a strength recommended to you by your chemical supplier. 3. Open the front door and flip the on-off/flush switch to the "ON" position. The detergent tank will fill automatically. 4. Load glasses on the conveyor. The conveyor will stop when the glasses contact the conveyor shut-off switch. 8

Cleaning Cleaning Instructions NOTE: The cleaning instructions are attached to the inside of glasswahser front door. Daily Cleaning or after 8 hours of Operation: 1. Make sure that any glasses on the conveyor are clean, then remove them from the conveyor. 2. Push the on-off/flush switch on the right-hand side of the glasswasher control box to the "OFF" position. 3. Remove the splash curtain from the curtain hooks located at each end of the splash curtain rod. 4. Remove the (2) stainless steel conveyor guards located at each corner of the glasswasher and the plexiglass stop assembly. 5. Remove the cylindrical stainless steel conveyor guard located in the center of the glasswasher. 6. Remove the conveyor by lifting the rear of the conveyor while pulling it forward to disengage the conveyor drive gear located at the right front corner of the wash chamber. 7. Take these parts to a sink and wash in hot soapy water using a soft brush and cloth, then rinse with fresh water and set aside to air dry. DO NOT: Do not clean with harsh detergents or abrasive scouring pads. Do not strike the conveyor on the floor or any hard surface. Do not strike screens on hard surfaces. 8. Clean the wash chamber interior with hot soapy water, then rinse with fresh water. Wipe the interior with a soft cloth. Allow the wash chamber to air dry overnight. 9. Remove the upper scrap screen, remove large debris in a trash can, take screen to a sink, and flush screen with fresh water. DO NOT: Do not leave water in the glasswasher overnight. 10. Remove the lower scrap screen, remove large debris in a trash can, take screen to a sink and flush screen with fresh water. 11. Remove the stainless steel wash tank cover; clean with hot soapy water at the wash sink. Wipe clean and dry. 12. Remove the detergent wash tank drain/overflow to drain the tank, then flush the tank with fresh water and wipe with a clean cloth. 13. Reassemble the glasswasher in reverse order for continued operation, or leave disassembled overnight to aid drying. Continued on the next page. 9

Cleaning Cleaning Instructions (continued) Weekly Cleaning, after 7 days or 56 hours of Operation 1. Complete 1-11 in the Daily Cleaning section on the previous page. 2. Remove chemical supply containers if they are stowed inside the glasswasher, wipe any chemical spills with a damp cloth. Detergent and sanitizer (Chlorine) are corrosive on metal and must be removed as much as possible. 3. Check the inlet chute on the right side of the detergent tank and flush with fresh warm water to clean any chemical residue. 4. Check chemical supply lines. If a line is restricted, remove the pick-up tube from the container, then insert it into a separate container filled with fresh warm water. 5. PUSH and HOLD the PRIME BUTTON labeled for the matching chemical tube until the water moves freely through the supply tubing. Repeat for each chemical making sure that the warm water is fresh and free of any other chemical. 6. Return the pick-up tubes to the chemical container matching the label on the supply tube, then PUSH and HOLD the PRIME BUTTON for the corresponding chemicals until the chemical moves freely through the supply tube. 7. Inspect the chemical dispensing pumps visible behind the plexiglass window located on the front of the control box. 8. Find the spray tube assemblies, (3 spray tubes each) located in the wash chamber. There are (2) assemblies in the top and (2) assemblies in the bottom. Pull (1) assembly at a time. Check the black O-ring on the spray tube hub for damage, replace if missing. 9. Insert and twist the small brass drill bit (reamer) in each spray tube hole to clean. Insert and twist the large drill on the wood handle. Push the large reamer down the length of the spray tubes. Insert and twist the long brush in each spray tube to remove loose debris. Flush the spray tube assembly, then reinstall in the glasswasher. Repeat for each spray tube assembly. 10. Reassemble the glasswasher in reverse order for continued operation, or leave disassembled overnight to aid drying. 10

Blank Page This Page Intentionally Left Blank 11

Troubleshooting The following troubleshooting guide can help identify a problem and provide a solution. Inspect your glasswasher before you contact an authorized service representative. Problem Cause(s) Solution(s) Glasswasher will not turn ON. Conveyor will not rotate. Conveyor will not stop rotating. Conveyor rotates in wrong direction. Upper scrap screen is hard to remove. Front door will not close or remain closed. Glasswasher not level or rocks back and forth. 12 Main breaker/fuse box is OFF. Disconnect fuse blown/breaker tripped. Glasswasher ON/OFF switch OFF. Power cord unplugged. Clean glass(es) touching the conveyor shut-off switch. Conveyor center hub out of position. Conveyor support(s) out of position and/or broken. Drive gear out of position. Gear teeth on conveyor worn or broken. Gear teeth on drive gear worn or broken. Object jamming the conveyor. Conveyor drive motor defective. Conveyor stop switch needs adjustment or switch is defective. The drive motor is turning the conveyor backward. Large debris, such as broken glass, is on screen. Scrap screen bent and/or broken. Door magnet broken or missing. Door bent or broken. Leg(s) are not screwed firmly into machine base. Turn breaker/fuse box ON. Turn breaker/fuse box ON. Replace fuse/reset breaker. Flip ON/OFF switch ON. Plug-in power cord. Remove clean glasses from the rinse-side of the glasswasher. Reposition the conveyor. Reposition or replace support(s). Reposition drive gear. Replace the conveyor. Replace drive gear. Remove object. Authorized Service Agent may replace conveyor drive motor. Authorized Service Agent may adjust or replace switch. Authorized Service Agent may remove drive motor and rotate motor stator 180 and re-install. Remove conveyor and lower spray arm(s). Remove debris. Authorized Service Agent may repair or replace damaged screen. Replace door magnet. Straighten or replace door. Tighten leg(s) or replace.

Troubleshooting Problem Cause(s) Solution(s) Water sprays our the front of the glasswasher. Poor washing results. Chemical supply container(s) fill with water. Splash curtain is missing, positioned incorrectly, or damaged. Spray arm(s) are damaged or missing. Glass(es) interferes with splash curtain. Clogged spray arm(s) makes water come out in wrong direction. Water volume from wash and/or rinse spray arm(s) low. Water level in detergent tank low. Water level float ball stuck or filling with water. Water level switch defective. Detergent and/or rinse-aid supply low. Wash pump and/or water valve(s) and/or line strainers clogged or defective. Detergent tank temperature low. Chemical injectors out of adjustment. Peristaltic tube(s) are stretched or worn on the glasswasher chemical pumps. Flow control washer in cold water solenoid valve is defective. Re-install the splash curtain or replace the splash curtain. Replace spray arm(s). Reload glass(es). Clean the spray arm(s). Clean spray arm(s). Re-install drain/overflow tube in wash tank. Service Agent must adjust water level switch until water level is below top of overflow. Clean float ball, replace if filling with water. Authorized Service Agent may replace switch. Refill chemical supplies. Authorized Service Agent may replace wash pump and/or solenoid valve(s). Clean line strainers. Raise incoming water temperature or adjust thermostat for 140 F/60 C in detergent tank. Contact chemical supplier to calibrate settings. Inspect and replace tube(s). Contact Service Agent to repair solenoid valve. 13

Troubleshooting Problem Cause(s) Solution(s) Water temperature below 145 F/66 C in detergent tank. Water leaking under glasswasher. Detergent tank thermostat tempeature setting low. Thermostat is defective. Detergent tank heater is defective. Incoming water temperature is below 140 F/60 C. Pump water seal defective. Glasswasher drain line is clogged. Upper wash compartment drain screen is clogged. Detergent tank drain screen is clogged. Building drain line is clogged. Condensation is forming on the underside of wash compartment. Vacuum breaker at rear of glasswasher leaking. Increase thermostat setting to 145 F/66 C. Authorized Service Agent may replace thermostat. Authorized Service Agent may replace detergent tank heater. Raise incoming water temperature to 140 F/66 C Authorized Service Agent may replace pump seal. Clean drain line. Clean drain screen. Clean detergent tank drain screen. Clean building drain line. Open rinse water mixing valve until temperature of water is 70 F/21 C. Replace vacuum breaker. 14

Problem Cause(s) Solution(s) Troubleshooting Water flows into glasswasher when ON/OFF switch is in the OFF position. Chemical(s) are not flowing into the glasswasher. FLowing water supply line pressure measured at the glasswasher exceeds 95 PSI (655 kpa). Defective solenoid valve(s). Defective AUTO-FILL switch. Rinse water pressure too high. Chemical container(s) are empty. Chemical supply line(s) are clogged. Chemical supply and/or pump tube(s) are broken. No power to chemical dispensing pump(s). Dispensing pump is defective. Chemical pumps out of adjustment. Incoming water pressure must be 5 PSI/35 kpa on pressure gauge located on right-side of glasswasher lower compartment. Authorized Service Agent may rebuild or replace solenoid valve(s). Service Agent may replace the switch. Reduce flowing water pressure measured at the glasswasher below 95 PSI (655 kpa). Refill the container(s). Remove the supply line(s) from the chemical container(s) and flush with warm water. Replace supply line(s) and/ or pump tube(s). Authorized Service Agent may replace chemical dispensing pump. Authorized Service Agent must inspect and repair. Chemical supplier must adjust chemical pumps. 15

Blank Page This Page Intentionally Left Blank 16

Service Replacement Parts Service Replacement Parts Illustration List Page Base Assembly... 18 Conveyor, Guides, Curtains... 20 Wash Hubs, Spray Arms... 22 Conveyor Stop Switch... 24 Drive Motor Assembly... 26 Vacuum Breaker Assembly... 28 Wash Pump and Piping... 30 Inlet Plumbing... 32 Sanitizer Plumbling... 34 Detergent Tank Assembly... 36 Control Box Assembly... 38 Options and Accessories... 40 17

Base Assembly 7 11 7 13 12 1 2 10 3 19 18 17 13 14 4 16 15 8 9 7 10 4 14 7 4 6 5 18

Base Assembly Item Part Description Qty. No. No. 1 112519 PLUG, CAP 1" 1 2 0501885 DOOR CATCH, MAGNETIC 1 3 0713746 SCRAP SCREEN, WASH TANK (Includes Item 19) 1 4 0501873 LEG 6" 4 5 0712692 DOOR ASSY. 1 6 111561 HANDLE, DOOR 1 7 0510884 SCREW, 1/4-20 X 1/2" TRUSS HEAD 10 8 0712647 BRACKET, DOOR 1 9 0501412 SCREW, 10-32 X 3/8" 2 10 0312598 PANEL, FLAT FACIA 1 11 0312601 PANEL, REAR 1 12 0501476 WASHER, FLAT 1/4" 2 13 107967 NUT, 1/4-20 NYLON LOCK 2 14 0501464 SCREW, 10-24 X 3/8" 2 15 0505112 LABEL, DATA PLATE 1 16 0503301 LABEL, WARNING 1 17 0512659 LABEL, CLEANING INSTRUCTIONS 1 18 0514421 LABEL, ELECTRICAL SCHEMATIC 1 19 0507471 LABEL, CLEAN SCREENS DAILY 1 19

Conveyor, Guides, Curtains 1 2 3 5 4 3 6 7 20

Conveyor, Guides, Curtains Item Part Description Qty. No. No. 1 0313603 HUB, CONVEYOR 1 2 0312695 BLOCK, CONVEYOR GUIDE 4 3 0312604 TRAY, CONVEYOR 2 4 0506886 GEAR, DRIVE 1 5 0506885 CONVEYOR 1 6 0312610 ROD,CURTAIN, 3/8" D X 24" L 1 7 0512549 CURTAIN 1 21

Wash Hubs, Spray Arms 1 2 upper wash spray arm notch in center 1 10 upper rinse spray arm notch on right 11 12 13 4 3 6 7 3 2 8 1 3 2 5 3 9 8 1 2 lower wash spray arm notch in center lower rinse spray arm notch on left 22

Wash Hubs, Spray Arms Item Part Description Qty. No. No. 1 0501613 WASH ARM 2 2 0501738 RINSE ARM 2 3 0501608 O-RING 4 4 0501610 TOP MANIFOLD 1 5 0301622 BOTTOM MANIFOLD 1 6 0501476 FLAT WASHER, 1/4" 1 7 0501422 BOLT, 1/4-20 X 1-1/2" 2 8 0501412 SCREW, 10-32 X 3/8" 2 9 0500813 BOTTOM MANIFOLD INLET TUBE 2 10 0502663 BRAIDED HOSE, 3/8" A/R 11 0503679 GEAR CLAMP #6 4 12 0509478 GROMMET 2 13 0300908 TUBE, RINSE 2 23

Conveyor Stop Switch 1 2 4 5 3 6 7 8 11 9 15 10 16 18 17 14 13 12 11 11 24

Conveyor Stop Switch Item Part Description Qty. No. No. 1 0512556 PLATE, DIVIDER 1 2 0713771 SHUT-OFF ARM ASSY. 1 3 0501412 SCREW 10-32 X 3/8" 2 4 0513768 BUSHING, SHAFT SHUT-OFF ARM 1 5 0513775 O-RING 1 6 0512559 SPRING 1 7 0513770 SHAFT, CONVEYOR SHUT-OFF 1 8 106558 PIN, COTTER 1 9 0513769 NUT 1 10 0313773 BRACKET, SHUT-OFF ARM LS 1 ---- 0313774 BRACKET, SHUT-OFF ARM RS 1 11 107697 NUT, 1/4-20 WITH NYLON INSERT 3 12 0510854 SCREW, DOG-POINT 1/4-20 X 1/2" 1 13 0512557 CONVEYOR SHUT-OFF CAM 1 14 0513789 HOUSING, CONVEYOR SWITCH 1 15 0501379 SWITCH 15A 1 16 0501437 SCREW 4-40 X 1/2" 2 ----- 0714437 SHUT-OFF ASSEMBLY (INCLUDES ITEMS 1-3) 1 25

Drive Motor Assembly 1 2 3 8 7 5 4 5 6 26

Drive Motor Assembly Item Part Description Qty. No. No. 1 0506886 GEAR, DRIVE 1 2 0507264 SLINGER, WATER 1 3 0501923 SPRING, EXTENSION 1 4 0512713 BUSHING, SNAP 1 5 0501412 SCREW 10-32 X 3/8" 4 6 0307617 COVER, DRIVE MOTOR HOUSING 1 7 0512532 MOTOR, DRIVE 230VAC 1 8 0712712 HOUSING, DRIVE MOTOR 1 27

Vacuum Breaker Assembly 4 5 3 2 6 2 1 1 7 8 9 28

Vacuum Breaker Assembly Item Part Description Qty. No. No. 1 0502665 HOSE,1/2" I.D. BRAIDED A/R 2 0503679 CLAMP, 7/16" GEAR 2 3 0502653 BARB, HOSE 3/8" MPT X 1/2" 90 1 4 100500 BREAKER, VACUUM 1/2" 1 5 0508366 KIT, REPAIR VACUUM BREAKER 1 6 0502651 COUPLER, HOSE 1/2" MPT X 1/2" 1 7 0312684 SUPPORT, PLUMBING 1 8 0501476 WASHER, FLAT 1/4" 2 9 107967 NUT, 1/4-20 NYLON LOCK 2 29

Wash Pump and Piping 7 13 11 12 11 8 8 8 10 9 6 3 1 5 2 4 30

Wash Pump and Piping Item Part Description Qty. No. No. 1 0512679 MOTOR CAPACITOR 6.3uF, 370VAC 1 2 0512531 PUMP/MOTOR COMPLETE 230V/50-60Hz/1Ph 1 3 0512678 PUMP KIT (INCLUDES ITEMS 4-6) 1 4 0512677 SEAL, PUMP 1 5 0512680 IMPELLER, PUMP 1 6 0512746 O-RING, WASH PUMP 1 7 0507320 HOSE 1" I.D. X 1-1/4" OD 6 8 0502563 CLAMP,HOSE #6 A/R 9 0502668 HOSE,BRAIDED 1" I.D. X 1-3/8" O.D. 6 10 0501632 CONNECTOR, PUMP HOSE 1 11 0503679 CLAMP, HOSE #16 A/R 12 0502665 HOSE, BRAIDED 1/2" I.D. X 3/4" O.D. A/R 13 0502663 HOSE, BRAIDED 3/8" I.D. X 5/8" O.D. A/R NOTE: The pump motor is not available as a separate service replacement part. 31

Inlet Plumbing To Vacuum Breaker 6 8 7 1 To Detergent Tank 8 6 2 4 7 9 1 3 Cold Water Valve 2 5 2 3 15 14 13 20 Hot Water Valve Water solenoid detail 12 21 19 10 16 11 1 18 22 17 23 32

Inlet Plumbing Item Part Description Qty. No. No. 1 0502783 VALVE, SOLENOID 230VAC/60 HZ 2 2 0503802 TEE, 3/8" MPT 3 3 0503801 ADAPTER, 3/8" FEM X 1/2" 1 4 0507324 VALVE, CHECK 3/8" 1 5 0502768 VALVE, STOP 1 6 0502653 BARB, HOSE 3/8" X 1/2' 90 2 7 0503679 CLAMP, GEAR 7/16" 2 8 0502665 HOSE, BRAIDED 1/2" I.D. X 3/4" O.D. A/R 9 0509659 CAP 1 10 0504822 SCREW 8-32 X 1/2" 2 11 0306208 COVER, CABLE CLAMP 2 12 0307373 CLAMP, CABLE 2 13 0501404 SCREW 10-32 X 3/8" BRASS 2 14 0501493 WASHER, LOCK #10 2 15 0501533 NUT 10-32 BRASS 2 16 0505229 GUIDE, SOLENOID 1 17 0502811 KIT, DIAPHRAGM A/R 18 0502810 WASHER, FLOW (2.6 gpm) 1 19 0502807 WASHER, BRASS 1 20 0502804 GASKET, STRAINER CAP 1 21 0502803 SCREEN 1 22 0501406 SCREW 8-32 X 1/2" 2 23 0502806 COIL, SOLENOID VALVE, 230VAC/60 1 33

Sanitizer Plumbing 1 14 2 13 3 2 4 2 15 1 6 7 2 1 5 2 8 12 10 11 10 9 34

Sanitizer Plumbing Item Part Description Qty. No. No. 1 0502665 HOSE, BRAIDED 1/2" I.D. X 3/4" O.D. A/R 2 0503679 CLAMP, GEAR 7/16" 5 3 0502663 HOSE, BRAIDED 3/8" I.D. X 5/8" O.D. A/R 4 0502652 TEE, 1/2" X 1/2" X 3/8" 1 5 0503669 FITTING, BARB INJECTOR 1 6 0501519 TIE, CABLE 4" 2 7 0502666 TUBING, CHEMICAL 1/8" I.D. X 1/4" OD A/R 8 0502653 BARB, HOSE 3/8" MPT X 1/2" 90 1 9 0503668 THERMOMETER 1 10 0502577 BUSHING, REDUCER 3/8" X 1/4" 2 11 0502583 CONNECTOR, CROSS 3/8" FPT 1 12 0507100 GAUGE, PRESSURE 0-30 PSI 1 13 0300918 CLAMP 1 14 0512185 BOLT, 1/4-20 X 3/8" 2 15 0502645 BARB, HOSE 1/8" 2 35

Detergent Tank Assembly 1 2 3 43 4 5 6 9 26 24 7 27 28 23 6 29 25 21 7 22 8 10 41 42 11 12 30 31 32 33 26 34 35 37 38 39 17 18 16 13 14 36 40 19 15 20 36

Detergent Tank Assembly Item Part Description Qty. No. No. 1 0312592 COVER, STEAM 1 2 0312591 COVER, DETERGENT TANK 1 3 0712641 SCREEN, DETERGENT TANK 1 4 0700948 STANDPIPE, DETERGENT TANK 1 5 201669 LOCKNUT, 1/4 NPT, NICKLE PLATE 1 6 0501397 SCREW, SET 6-40 X 3/16" SOCKET SST 2 7 0703673 COLLAR (SET SCREW INCLUDED) 2 8 0512554 ROD, FLOAT 1 9 0503670 BALL, FLOAT 1 10 0307427 TUBE, WATER INLET 1 11 107967 NUT, GRIP 1/4-20 W/NYLON INSERT 1 12 0502668 HOSE, PVC 1" I.D. X 1-3/8" OD 6" 13 0502563 CLAMP, GEAR 1" 1 14 108051 FLANGE, ELBOW 1 15 0507431 BOLT M6 X 25MM (METRIC) 4 16 107886 GASKET, INLET CHUTE 1 17 107435 NUT, M6 (METRIC) 4 18 0712640 TANK, DETERGENT 1 19 0512185 BOLT, HEX FLANGE 1/4-20 X 3/8" SST 2 20 0512534 TEE, MOLDED DRAIN 1 21 0512536 GASKET, DRAIN 1 22 0512535 DRAIN SEAT, MOLDED 1 23 0501395 SCREW, SET 1/4-20 X 5/16" SST 1 24 0514413 CAM, FLOAT 1 25 0512550 BUSHING, FLOAT ROD 1 26 0502571 CLAMP, HOSE 1-1/2" 2 27 0512533 HOSE, MOLDED DRAIN 1 28 0503723 SCREW, 6/32 X 1" 2 29 0501375 SWITCH, TRIP C/W ROLLER 1 30 0514175 SCREW, NYLOCK 9-32 X 3/8" SST 2 31 0501412 SCREW. 10-32 X 3/8" TRUSS HD. PHIL. SST 1 32 0314416 BRACKET, FLOAT SWITCH 1 33 0502977 WELDNUT, DUAL 6/32 NICKEL PLATED 1 34 0501896 SEAL, THERMOMETER 1 35 0501600 THERMOMETER, 8" STEM 1 36 0507323 THERMOSTAT 1 37 0501650 ADAPTER, THERMOSTAT 1 38 0501836 O-RING 1 39 0503588 O-RING, HEATER (Comes with Item 40) 1 40 0507315 HEATER, DETERGENT TANK 3kW (Includes Item 39) 1 41 0503679 CLAMP, HOSE #6 1 42 0502665 HOSE, BRAIDED 1/2" A/R 43 0507471 LABEL, CLEAN SCREENS DAILY 1 37

38 Control Box Assembly 2 1 3 4 5 5 6 7 12 14 10 9 8 11 13 15 17 18 19 20 20 20 16 DET R/A SANI 21 28 24 25 26 27 28 21 21 22 22 23 29 30 32 31 36 33 34 35 35

Control Box Assembly Item Part Description Qty. No. No. 1 0503647 STRAIN RELIEF BUSHING (LARGE) 1 2 0512713 STRAIN RELIEF BUSHING (1/2") 3 3 0501404 SCREW, 10-32 X 3/8" ROUND HEAD, BRASS 1 4 0501493 WASHER, LOCK #10 EXT. TOOTH BRASS 1 5 0512185 BOLT, HEX FLANGE 1/4-20 X 3/8" SST 2 6 0501533 NUT, 10-32 BRASS 3 7 0501472 WASHER, FLAT, #10 BRASS 2 8 0314412 BOX, CONTROL 1 9 0512663 LABEL, PRIME 1 10 0512539 SWITCH, ROCKER, ON/OFF/FLUSH 1 11 0508710 SPACER, CONTROL BOARD 4 12 0508433 CIRCUIT BOARD, MOTOR CONTROL 1 13 0507323 THERMOSTAT, CONTROL 1 14 0503749 BOARD, TERMINAL 11 PT 2 15 0312590 WINDOW, CONTROL BOX COVER 1 16 0312589 COVER, CONTROL BOX 1 17 0508920 TRANSFORMER, 240VAC/18VAC, 30VA 1 18 0514162 RELAY, DPST 30A, 240VAC, 240VAC COIL 1 19 0312588 PANEL, CHEMICAL PUMP 1 20 0501353 MOTOR, INJECTOR 140 RPM, 24VDC 3 21 0707142 ROTOR, INJECTOR 3 22 0706635 TUBE, ELEMENT 45cc (DET,ERGENT, SANITIZER) 2 23 0706634 TUBE, ELEMENT ASSY 15cc (RINSE-AID) 1 24 0501869 STRAINER 3 25 0306363 TUBE, STIFFENER 3 26 0502666 TUBING, CHEMICAL 1/8" I.D. X 1/4" O.D. A/R 27 0503695 LABEL, DETERGENT 1 ---- 0503694 LABEL, SANITIZER 1 ---- 0505483 LABEL, RINSE-AID 1 28 0504822 SCREW, 8-32 X 1/2" PAN HD. PHIL. SST 12 29 0501411 SCREW, 10-32 X 1/4" 12 30 0501408 SCREW. 8-32 X 1/4" TRUSS HD. PHIL. SST 2 31 0503648 SCREW, 8-32 X 3/8" PAN HD. SST 2 32 0504823 RIVOT, POP 1/8" ALUMINUM 2 33 0504411 SCREW, 10-32 X 1/4" RD. HD. PHIL. SST 1 34 106695 SCREW, 6-32 X 1/2" ROUND HD. PHIL. 4 35 0501450 SCREW, NIBS RH 6-32 X 3/16" PHIL. SST 2 36 0713778 SNUBBER COMES W/FASTONS 1 ---- 0512538-1 HARNESS, WIRING (NOT SHOWN) 1 39

Options And Accessories 1 2 3 4 7 5 5 6 8 9 10 12 11 40

Options and Accessories Options and Accessories Item Part Description Qty. No. No. 1 0708986 TUBE SCRAPER 1 2 0501826 TUBE BRUSH 1 3 0501633 JET REAMER (COMES WITH DRILL) 1 Item Part Description Qty. No. No. 4 0510571 NOZZLE, WASHDOWN 1 5 0505320 1/2" HOSE WASHER 1 6 0501833 1/2" X 10' HOSE ASSY. 1 7 0506643 FAUCET 1 ---- 0503801 ADAPTER, 3/8" FEM X 1/2" FEM (NOT SHOWN) 1 ---- 0701956 WASH DOWN HOSE KIT (Includes items 4-8) 1 Item Part Description Qty. No. No. 8 0512719 SCREEN, DRAIN TRAY 1 9 0512717 TRAY, DRAIN 1 10 0512943 TUBE, DRAIN 1 11 0512688 GROMMET 1 12 0512946 NUT, 5/8-20 BULKHEAD, POLY. 1 ---- 0712551 DRAIN TRAY AND WASTE COLLECTOR KIT (Includes items 8-12) 1 41

Electrical Schematic 42