TA, TA,B, TA,B, TB Digital Fan-Coil Thermostats XE/XE00 SERES FEATURES PRODUCT DATA Attractive modern styling with digital display makes the thermostat ideal for offices or hotels. Hotel card key input overrides the temperature setting to installer-defined heating and cooling temperatures. All models have proportional plus integral control that controls temperature to within 0.ºC in both heating and cooling. Thermostat mounts directly onto a wall, a in. x in. horizontal junction box, or a mm x mm standard European junction box. Switches allow manual control of system operation and fan speed. Digital display of room ambient temperature in ºC. APPCATO The T and T Thermostats are designed for on/off control of the valve, or the valve and fan in -pipe fan-coil applications and also one-stage compressors in DX-type equipment. The T and T Thermostats are designed for series 0 floating control of the valve and fan in -pipe fan-coil applications, and also variable air volume (VAV) equipment (M, M). The thermostat operates an on/off or Series 0 valve to provide control at the desired setpoint temperature. Heat/cool models are available with constant or cycled fan operation. The fan is wired to run continuously on cool only models. Models are available with either a three-speed fan selector switch with low, medium and high settings, or onespeed only. On models with a system on/off switch, the fan can be powered off. Digital display of user selected temperature setting on demand. Capability to display temperature sensor failure for easier troubleshooting. Capability to select minimum relay off-times for compressor short cycle protection (only T and T). EEPROM permanently retains user settings in the event of power loss. Direct line voltage, 0 to 0 Vac, 0/0 Hz power input (only T and T). Controls Honeywell V0 and VC000 Series Valves, M and M damper actuators, and compressor starters/relays up to A full load rating (only T and T). Contents Application... Features... Specifications... Ordering nformation... nstallation... Operation... Checkout... U.S. Registered Trademark Copyright Honeywell nc. All Rights Reserved -0-
TA, TA,B, TA,B, TB DGTA -CO THERMOSTATS SPECFCATOS MPORTAT The specifications given in this publication do not include normal manufacturing tolerances. Therefore, this unit may not exactly match the listed specifications. This product is tested and calibrated under closely controlled conditions, and some minor differences in performance can be expected if those conditions are changed. Models: See Table. Setpoint Range: 0ºC to 0ºC. nput Voltage: T, T: 0 to 0 Vac, ±0%, 0/0 Hz. T, T: to 0 Vac (Heat/Cool Thermostat). 0 to 0 Vac (Fan). Operational ife: Thermostat Contacts (at 0 to 0V): Greater than 00,000 cycles (all loads). Manually-Operated Switches: Greater than 0,000 operations. Mounting: Direct: Wall-mount. in. x in. junction box. mm x mm standard European junction box. Table. Model Specifications. Switches Series OS umber Application a Fan Operation Card Key System On/Off Fan Speed Heat/Cool TA00 Cool constant o Yes -speed o TA0 Cool constant o o -speed o TA0 Cool constant Yes Yes -speed o TA00 Cool constant o Yes -speed o TA0 Cool constant Yes Yes -speed o TA0 Cool constant o o -speed o XE TB00 Heat/Cool cycled Yes Yes -speed Yes TB0 Heat/Cool cycled o Yes -speed Yes TB0 Heat/Cool cycled o o -speed Yes TB0 Heat/Cool constant Yes Yes -speed Yes TB0 Heat/Cool constant o Yes -speed Yes TB0 Heat/Cool constant o o -speed Yes TA000 Cool b constant Yes Yes -speed o XE00 TB00 Heat/Cool b constant Yes Yes -speed Yes TB00 Heat/Cool b constant Yes Yes -speed Yes acontrols V0 and VC000 Series Valves or On/Off relays. bseries 0 modulating output. ORDERG FORMATO When purchasing replacement and modernization products from your TRADEE wholesaler or distributor, refer to the TRADEE Catalog or price sheets for complete ordering number. f you have additional questions, need further information, or would like to comment on our products or services, please write or phone:. Your local Home and Building Control Sales Office (check white pages of your phone directory).. Home and Building Control Customer ogistics Honeywell nc., Douglas Drive orth Minneapolis, Minnesota - () -000 n Canada Honeywell imited/honeywell imitée, Gordon Baker Road, orth York, Ontario MH. nternational Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France, Germany, Japan, Mexico, etherlands, Spain, Taiwan, United Kingdom, U.S.A. -0
TA, TA,B, TA,B, TB DGTA -CO THERMOSTATS Enclosure: Two-piece plastic housing. Wiring: Up to ten screw-in terminals per unit. Accepts two. mm wires per terminal. Temperature Ratings: Ambient: ºC to ºC. Shipping and Storage: -0ºC to ºC. Humidity Range: % to % RH, non-condensing. Performance: Control Temperature: ±0.ºC at ºC with 0% load. Hotel Card Key nput: Temperature Setpoint Range: ºC to 0ºC. Dry Contact Rating: Vdc, maximum contact resistance of 000 ohms. System Switches and Fan Speeds: See Table. Output Ratings: T, T: 0 to 0 Vac, A run, A inrush. T, T: Vac, A run, A inrush (Heat/Cool Thermostat). 0 to 0 Vac, A run, A inrush (Fan).. nstaller must be a trained, experienced service technician.. After installation is complete, check out product operation as provided in these instructions. ocation CAUTO Electrical Shock Hazard. Can cause electrical shock or equipment damage. Disconnect power supply before beginning wiring. The XE/XE00 Thermostats are temperature control elements in fan-coil or air conditioning systems and should be installed about one and one-half meters above the floor in an area with good air circulation at room temperature. OTE: evel only for appearance. The thermostat functions normally even when not level. Do not mount the thermostat where it can be affected by: drafts or dead spots behind doors and in corners. hot or cold air from ducts. radiant heat from the sun or appliances. concealed pipes and chimneys. unheated (uncooled) areas such as an outside wall behind the thermostat. Dimensions: See Fig.. System Components: V0, VC0, VC0 Fan-Coil Valves (on/off models). VC Fan-Coil Valves (Series 0 models). M, M Vac Damper Actuators (Series 0 models). STAATO When nstalling this Product. Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous condition.. Check the ratings given in the instructions and on the product to make sure the product is suitable for your application. mm mm MPORTAT This thermostat is a precision instrument and was adjusted at the factory. Handle it carefully. Mounting Thermostat The XE/XE00 Thermostats can be mounted directly on the wall, or horizontally on either a in. x in. junction box, or a mm x mm standard European junction box. Mounting screws and draw nuts are provided. Flush Mount To mount the thermostat to the wall surface or to a junction box that is flush with the wall:. nsert the screws through the mounting holes as shown in Fig... Tighten the screws. mm 0 mm mm mm Fig.. T, T, T, and T dimensions (in mm). M0-0
TA, TA,B, TA,B, TB DGTA -CO THERMOSTATS Recessed Mount To mount the thermostat to a recessed junction box:. nsert the screws through the mounting holes as shown in Fig... Position the draw nut between the junction box and the subbase and tighten it. M Fig. A. Removing thermostat from subbase. Wire the thermostat as follows:. Wire the subbase through the center entrance hole. OTE: Wiring terminals are straight-in screw type and are designed to accept two. mm wires per terminal. Fig.. Mounting thermostat. M0. When wiring is complete, attach the thermostat to the subbase: a. ocate the two center side holes on the back of the thermostat. b. Align the holes with the two side tabs on the subbase. c. Press down firmly and snap the thermostat into place. Refer to Fig. through for typical wiring diagrams. Removing the Thermostat f it becomes necessary to remove the thermostat from the base:. Pry the left side of the thermostat away from the base (see Fig. a).. Pry the right side of the thermostat away from the base (see Fig. a).. Use both hands to pull the thermostat straight away from the base (see Fig. a). MPORTAT mproper removal of the thermostat from the subbase may damage the device. Wiring Thermostat MPORTAT Use a. mm gauge maximum wire for wiring the T, T, T, and T Thermostats. CAUTO Electrical Shock Hazard. Can cause electrical shock or equipment damage. Disconnect power supply before beginning wiring. TA00 / TA0 O/OFF REAY O OFF VAVE PROVDE DSCOECT MEAS AD OVEROAD PROTECTO AS REQURED. PROVDED O TA0. COTACT COSURE AT TERMAS 0, RETURS THERMOSTAT TO EERGY SAVGS SETTG. M0 0 VC0 0...0V Fig.. TA00 and TA0 cool-off wiring diagram with -speed fan. -0
TA, TA,B, TA,B, TB DGTA -CO THERMOSTATS TA0 0...0V TA00 / TA0 0...0V REAY VC0 0 O/OFF REAY O OFF VAVE 0 VC0 PROVDE DSCOECT MEAS AD OVEROAD PROTECTO AS REQURED. M0 Fig.. TA0 cool-continuous on wiring diagram with -speed fan. TA0 REAY PROVDE DSCOECT MEAS AD OVEROAD PROTECTO AS REQURED. 0 VC0 0...0V M0 Fig.. TA0 cool-continuous on wiring diagram with -speed fan. PROVDE DSCOECT MEAS AD OVEROAD PROTECTO AS REQURED. PROVDED O TA0. COTACT COSURE AT TERMAS 0, RETURS THERMOSTAT TO EERGY SAVGS SETTG. M0 Fig.. TA00 and TA0 cool-off wiring diagram with -speed fan. TB00 / TB0/TB0/TB0 HEAT HEAT/ O/OFF O OFF REAY /HEAT VAVE PROVDE DSCOECT MEAS AD OVEROAD PROTECTO AS REQURED. PROVDED O TB00 AD TB0. COTACT COSURE AT TERMAS 0, RETURS THERMOSTAT TO EERGY SAVGS SETTG. M0 0 VC0 0...0V Fig.. TB00 and TB0 cool-heat-off wiring diagram with -speed cycled fan. -0
TA, TA,B, TA,B, TB DGTA -CO THERMOSTATS TB0/TB0 0...0V TB HEAT HEAT/ REAY /HEAT VC0 HEAT HEAT/ REAY REAY /HEAT VAC VC 0...0V 0 O PROVDE DSCOECT MEAS AD OVEROAD PROTECTO AS REQURED. Fig.. TB0 cool-heat wiring diagram with -speed cycled fan. M0 O/OFF 0 TA REAY REAY /HEAT 0...0V VAC VC A WRG MUST COMPY WTH OCA WRG AD ORDACES. PROVDED O SOME MODES. COTACT COSURE AT TERMAS 0, RETURS THERMOSTAT TO EERGY SAVGS SETTG. M0A Fig. 0. TB00 cool-heat-off wiring diagram with -speed fan. TB O HEAT A WRG MUST COMPY WTH OCA WRG AD ORDACES. O/OFF PROVDED O SOME MODES. COTACT COSURE AT TERMAS 0, RETURS THERMOSTAT TO EERGY SAVGS SETTG. 0 MA Fig.. TA000 cool-off wiring diagram with -speed fan. HEAT/ O/OFF REAY O REAY /HEAT 0 VAC 0...0V VC A WRG MUST COMPY WTH OCA WRG AD ORDACES. PROVDED O SOME MODES. COTACT COSURE AT TERMAS 0, RETURS THERMOSTAT TO EERGY SAVGS SETTG. MA Fig.. TB00 cool-heat-off wiring diagram with -speed fan. -0
TA, TA,B, TA,B, TB DGTA -CO THERMOSTATS OPERATO Proportional Plus ntegral Control The XE/XE00 Digital Fan-Coil Thermostats actually control closer to the setpoint than a conventional control, because the heat anticipator is replaced by proportional plus integral control. Proportional plus integral action eliminates the difference between the temperature setting and effective control point by adjusting the on-time of the cooling output until the control point matches the setpoint. The XE/XE00 Thermostats maintain the space temperature within 0.ºC of the setpoint. This control performance accuracy provides improved occupant comfort and energy savings. On/Off Models These models are intended for use in -pipe fan-coil and - pipe compressor applications with line voltage actuators. These models provide on/off control. They have a fixed cycle rate of cycles per hour (cph) at 0 percent load. Series 0 Models These models are intended for use in fan-coil applications with Vac series 0 actuators. These models provide modulating control of valves or dampers. The Vac series 0 actuator can have timings between and seconds. They have a fixed cycle rate of cph at 0 percent load. OTE: Switches Fan Switch The control algorithm is optimized for seconds. / / (ow/medium/high): Fan speed switch on threespeed models allows selection of three different settings. One-speed fan models with a system on/off switch can be switched off. System Switch / (Off/On): Fan-Coil equipment is powered off or on. When in the position, terminal five is powered to close the VC000 Valve (on/off models only). Heat/Cool Switch / (Heat/Cool): Thermostat switches between heat setpoint and cool setpoint. Fan-coil equipment provides heating or cooling. Settings Temperature (Comfort) Setpoint The temperature setpoint for desired room comfort can be adjusted between 0ºC and 0ºC by using the or keys. The temperature setpoint can be changed by pressing the key to increase the setpoint, or pressing the key to decrease the setpoint. The temperature setpoint indicated on the display is based on the [flame]/ (heat /cool) switch position. Hotel Card Key Setting and Operation The XE/XE00 Thermostats accept an external card key input that overrides the temperature setting to a user/installer defined heating and cooling temperature for increased energy savings. The thermostat default operation is with the comfort setting. f a card key input is connected to terminals 0 and, the XE/XE00 Thermostats control to the comfort (occupied) or energy saving (unoccupied) setting based on a contact closure. Contact closure at terminals 0 and results in control to the energy saving (unoccupied) setting as shown in Fig.. 0 M0 Fig.. Hotel card key input. The default settings for both comfort and energy savings are shown in Table. System Operation Table. Thermostat Default Settings. Comfort Setpoint Energy Savings Setpoint Heating 0ºC ºC Cooling ºC ºC The installer can adjust the energy saving settings between º and 0ºC. Settings are described in the nstaller Setup Mode section. Minimum Off-Time (T and T only) The T and T provide minimum relay off-times for compressor short cycle protection. This prevents the relay from energizing the load for the installer selected time. o minimum off-time is provided as the default setting (default time is zero minutes). The minimum off-time duration can be adjusted by the installer for 0,,, or minutes. Adjustment is described in the nstaller Setup Mode section. -0
TA, TA,B, TA,B, TB DGTA -CO THERMOSTATS nstaller Setup Mode Use the installer setup mode to make adjustments to the hotel card key input heating and cooling setpoints and the minimum off-time settings. OTE: When a parameter setting is changed and no additional entries are made for five seconds, the parameter (c, c, c) is displayed again. f no activity is detected for another five seconds, the user is exited from the installer setup mode. To enter the installer setup mode:. Press to change the temperature setpoint to ºC.. Wait until the room temperature is displayed.. Press simultaneously and hold approximately three seconds until c is displayed.. Press to display c to override the high setpoint for cooling.. Press simultaneously.. Press or to change the high setpoint.. Wait five seconds until c is displayed.. Press to display c to override the low setpoint for heating.. Press simultaneously. 0. Press or to change the low setpoint.. Wait five seconds until c is displayed.. Press to display c to change the minimum off-time.. Press simultaneously.. Press or to change the minimum off-time. CHECKOUT Cooling CAUTO Equipment Damage Hazard. mproper operation can cause compressor damage. Do not operate cooling if outdoor temperature is below 0ºF (0ºC). Refer to manufacturer recommendations. To avoid compressor damage, allow the compressor to remain off for five minutes before restarting. On models with cool-only, or heat ( ) and cool ( ):. f the device has a system switch, slide it to on).. f the device has a heat/cool switch, slide it to (cool).. Press the key to lower the temperature setting several degrees below the room temperature. After approximately ten seconds, the cooling equipment should start.. Press the key to raise the temperature setting above the room temperature. The cooling system should shut down. Heating On models with heat ( ) and cool ( ):. f the device has a system switch, slide it to on).. Slide the heat/cool switch to (heat).. Press and hold the key to raise the temperature setting several degrees above the room temperature. After approximately ten seconds, the heating equipment should start.. Press the key to lower the temperature setting below the room temperature. Heating equipment should stop. Make certain all equipment responds to the thermostat. Home and Building Control Honeywell nc. Honeywell Plaza P.O. Box Minneapolis M 0-0 Honeywell atin American Region 0 Sawgrass Corporate Parkway Suite 00 Sunrise F Home and Building Control Honeywell imited-honeywell imitée Gordon Baker Road orth York, Ontario MH Honeywell Europe S.A. Avenue du Bourget 0 Brussels Belgium Honeywell Asia Pacific nc. Room - Sun Hung Kai Centre o. 0 Harbour Road Wanchai Hong Kong Printed in U.S.A. on recycled paper containing at least 0% -0 B.B. Rev. - post-consumer paper fibers.