Operation Manual, Parts Directory and Price List

Operation Manual, Parts Directory and Price List MFV Reach-In Mug Chillers MFV-SS(L) with optional casters This manual applies to MFV models manufactured prior to SN0876N and July 0, 0. For MFV models manufactured after, please see the Front Venting Self-Contained Coolers and Mug Frosters manual. Glastender, Inc. 00 North Michigan Road Saginaw, MI 860-9780 800.78.0 989.7.7 Fax 989.7. www.glastender.com Rev 0-7-8 00 Glastender, Inc.

Index Installation Introduction... Utility requirements and connections... Uncrating and start-up instructions... Operation... Cleaning instructions... Floor sealing instructions... Electrical and refrigeration specifications... Service and Parts Terms and Conditions... arranty statement... iring Diagram... Parts and Service Compressor and condenser related parts...-6 Evaporator and related parts...7 Electrical components...8 Shelving and related parts...9 Doors, tops and related parts...0 Refrigeration compartment covers...

Installation Introduction This manual describes the operational features of the Reach-In Mug Chiller model MFV. Please review this information before attempting installation and operation. Long term, trouble-free service will follow if good housekeeping and maintenance procedures are followed. Thank you for selecting Glastender, Inc. products. Utility Requirements and Connections Electrical: Plumbing: Volt AC, Phase, 60 Hz, 8. Full Load Amps. A separate Amp circuit is recommended. A 6-foot grounded cord is included. Automatic condensate evaporator is included. No drain connection required. Uncrating and Start-Up Instructions All Reach-In Mug Chiller models are shipped in one carton. These steps should be followed:. If legs or casters are included, bolt them to the base with the bolts provided.. Unwrap power cord from base.. Position the Reach-In Mug Chiller and level and/or seal as required (see page ).. Install shelves.. Plug into volt AC outlet. 6. Load with mugs, glasses, plates, etc. 7. Your Glastender Reach-In Mug Chiller is now ready for use. Operation The Reach-In Mug Chiller is designed to chill mugs, glasses, plates, etc. that will appear frosted when removed. The operating temperature range of 0 F(-8 C) to F( C). The Reach-In Mug Chiller should be filled with dry, room-temperature mugs, glasses, plates, etc. to allow maximum chilling. During business hours, the Reach-In Mug Chiller can be loaded with additional dry, room-temperature mugs, glasses, plates, etc. Allow 0 minutes for chilling. The Reach-In Mug Chiller includes an automatic defrost system. Defrosting will occur every six hours for approximately 0 minutes. During the defrost cycle, the fan inside the Reach-In Mug Chiller will turn off and a small amount of mist may appear if the door is opened. There is also a manual defrost system controlled by a switch located on the front left bottom of the Reach-In Mug Chiller. This is used when there is ice or snow accumulation inside. An end-of-the-day or weekly schedule can be established for the activation of this manual defrost cycle. hen the manual defrost switch is pushed, a light will turn on and the Reach-In Mug Chiller will go into a six-hour defrost. After six hours, the Reach-In Mug Chiller will resume normal operation. If the manual defrost switch is accidentally pushed, the defrost cycle can be terminated by unplugging the power cord for three seconds.

Cleaning Instructions Installation Cleaning is essential to sustaining the integrity of your equipment and preventing corrosion. ESTIMATED CLEANING TIME: to 0 minutes per unit daily, minutes quarterly FREQUENCY: Daily cleaning of exterior & door gaskets. Quarterly cleaning of interior, including shelves. PROCEDURE:. A non-chlorine based cleaner or mild detergent and warm water applied with a soft cloth or sponge to all contact surfaces.. Immediately rinse off cleaning agent(s), using clean warm water, clean soft cloth or sponge.. Dry with a soft clean cloth, removing standing water as soon as possible. NOTES:. Never use hydrochloric acid, wire brushes, steel wool, scrapers, or chlorine based cleaners on stainless steel surfaces, since they will break down the passivity layer and allow corrosion to occur.. On stainless steel surfaces, you may use a soft bristle brush or Scotch-Brite pad for more stubborn stains. Always scrub with the direction of the grain. Follow with a thorough cleaning as described above.. Deposits from food preparation must be properly removed. Even hard water deposits will rust stainless steel, if not removed.. Repeated cleaning may dry up black-vinyl-clad steel (exterior) surfaces of the cooler. Armor All or similar product can bring back the shine. Apply the product to a cloth and then rub into the surface, rather than spraying it directly onto the black-vinyl-clad surface.. The cooler door gaskets are most often overlooked when cleaning. Failure to clean them regularly will lead to premature failure, since alcohol and moisture build-up breaks down the gasket material. Sealing Reach-In Mug Chiller Base to Floor To comply with NSF & health codes. The Reach-In Mug Chiller base must be sealed to the floor using NSF listed sealant. Place a bead of sealant along outer edges of the base and remove excess with disposable towel. Electrical and Refrigeration Specifications Design Model Refrigerant Pressure (L-to-R length) Electrical Type Charge High Low V, Ph., 60 Hz., 8. Amp R0A 9.7oz. 0 7

Terms and Conditions Prices: All prices are LIST. Applicable taxes will be added. Quotations: Unless otherwise stated, quotations are effective for 0 days only. Acceptance: All orders are subject to acceptance by Glastender, Inc. s headquarters in Saginaw, Michigan. Possession of the Product Directory and Price List is not an offer to sell. Shipments: F.O.B. factory in Saginaw, Michigan. Freight terms are Third Party or Collect if shipped directly to you. Prepay and Add to Invoice freight terms are available upon request. The approximate shipping weights of all products are listed with the prices. Partial shipments will be made unless otherwise specified by the customer. Surface freight classifications are: GT-/GT-0/G Glasswashers - Class 7 GT-8 Glasswashers - Class 0 All Underbar Equipment - Class 7 Bar Die Orders Class 0 Portable Bars - Class 7 Remote refrigerators (i.e., no compressor) or dry storage back bar equipment - Class 7 Self-contained refrigeration equipment - Class 0 Ice Display Units (IDU and GDU) - Class 8 Lighted Liquor Displays - Class 8 Beer line chillers and beer towers (beverage dispensing equipment) - Class 9. Bottle Disintegration System - Class 0 Ice Cream Freezers - Class 77. All small items are evaluated to see the most cost effective means for shipment. Many small items ship via UPS or FedEx; however, when dimensional weight is excessive, LTL carriers are the most cost effective choice. Spare parts orders received before :00 PM EST can usually be shipped the same day. The order department is happy to assist with routing or shipping questions. Delivery: The majority of equipment is manufactured to order and typically ships within three to six weeks after complete order information is received by the factory. In-stock equipment typically ships within two to three days of the factory receiving complete order information. Returns: Items specified as Manufactured to Order are NOT returnable. A Return Authorization number must be issued by the factory in advance for any items that are returnable. The number MUST be noted on the outside of the returned package. Returns must be received within 90 days of the issue date. Shipping charges must be prepaid. A minimum 0% restocking charge will be applied to all authorized returns if received in new, unused condition in the original packaging. The above conditions apply to spare part returns, except spare part returns must be received within 0 days of original shipment for electronic or electrical parts or within 90 days for all other parts. Loss or Damage: For customer routed shipments, Glastender, Inc. is not responsible for any loss, damage, or delay of merchandise during shipment. Such transit claims must be filed with the carrier. Merchandise must be examined on arrival. If shortages occur, Glastender, Inc. must be notified in writing within five () days of delivery to honor any shortage claim. Glastender will assume responsibility for freight claims on Prepay and Add shipments but the customer must inspect freight and note any damage upon receipt. Failure to do so may result in losses at the customer s expense. Custom Orders: Custom orders must be paid in advance and are not subject to cancellation. Laminates: Some products include common, readily available plastic laminates of the customer s selection. There may be an additional charge if uncommon varieties are ordered. //7 Payment Terms: Cash should be included with all orders unless credit terms have been arranged. To establish credit, banking and trade references are required. A convenient credit application is available upon request. Payment via credit card is not our normal means of receiving payment. Visa and MasterCard will be accepted, but must be charged at the time of shipment. In addition, a payment via credit card for orders totaling more than $00 will incur a % convenience fee on the total transaction amount.

iring Diagram P OPTIONAL GLASS DOOR HEATER FOR MFV- P A 7 B BL O O NEUTRAL POER VOLT AMP. SERVICE RECOMMENDED GROUND B B B P /R R M 7 8 9 BR OPENS ABOVE + F 6 0 P P P C S M M B LEGEND B = Black BL = Blue BR = Brown O = Orange R = Red P = Purple = hite /R = hite / Red 6 COMPRESSOR IRING /6/9 6 ELECTRICAL RATINGS V, Single Phase, 60Hz, wire. All wires are 6 Gauge Compressor Condensing Unit Fan Motor Evaporator Fan Motor TOTAL AMPS 7.60 AMP.8 AMP. AMP 8.8 ITEM DESCRIPTION LIGHT, MANUAL DEFROST, RED, v RELAY, EVAPORATOR FAN, v, MUG FROSTER MOTOR, EVAPORATOR FAN, v THERMOSTAT COMPRESSOR, / hp, R0a, (TECUMSEH) AFTER 0/00 6 CONDENSER, FAN MOTOR, 6 7 DEFROST TIMER, AUTOMATIC, v 6-HOUR, PARAGON 8 SENSOR, DEFROST 9 DEFROST HEATER, v 0 SITCH, MANUAL DEFROST, START AND CYCLE TEST MANUAL DEFROST TIMER, 6 HOUR OVERLOAD PROTECTOR, /hp R0a, TECUMSEH RELAY, /hp R0a, TECUMSEH COMPRESSOR START CAPACITOR, /hp R0a, TECUMSEH COMPRESSOR FAN BLADE, CONDENSER, BLADE GT# GT-0907 GT-00 GT-007 GT-006 GT-0 GT-0000 GT-0 GT-070 GT-00 GT-000 GT-007 GT-0 GT-006 GT-080 MT# 070007 0700066 0600 070006 070007 06009 060097 070006 0700069 070007 070006 070008 0700068 060080 07000 6 EVAPORATOR FAN BLADE, BLADE, BLACK GT-080 0900098 Mug Froster MFV iring

Compressor and Condenser Related Parts 9 6 7 8 0 0 9

Compressor and Condenser Related Parts Part No. Description Price. 070007 / HP Aspera compressor, R0A (prior to 0/00) $0.00. 07000 Start capacitor, Aspera / HP R0A compressor.00. 0600 Relay for / HP Aspera, R0A compressor.00. 070007 Overload protector, Aspera / HP R0A compressor.00. 070007 / HP Tecumseh compressor, R0A (after 0/00) 7.00 6. 060080 Start capacitor, for Tecumseh / HP R0A compressor 0.00 7. 0700068 Relay for Tecumseh, / HP R0A compressor. 8. 070008 Overload protector, for Tecumseh / HP R0A compressor.00 9. 06009 Motor, condenser fan, 6 00.00 0. 07000 Fan blade, condenser, blade (metal).00. 0600 Bracket, condenser fan motor mounting (metal).00. 0700079 Nut, condenser fan blade mounting.00. 07000 Fan shroud, condenser.00. 0600 Motor, circulation fan.00. 0900098 Fan blade, circulation fan, five blade (black plastic).00 6. 07000 Bracket, circulation fan motor 0.00 7. 070009 Accumulator, suction line 0.00 8. 08000078 Condenser coil.00 9. 08000 Pan, condensate 60.00 0. 07000 icking material, ", consists of pieces.00. 0600 Tubing, drain, clear plastic, " ID x /8" OD, per foot.. 06008 Filter dryer, /" x /" 0.00. 0600 Condensing unit power cord 0.00 6 7 8 Tecumseh / HP Compressor Tecumseh / HP Compressor 6

Evaporator and Related Parts Part No. Description Price 0700080 Evaporator coil replacement kit, prior to SN 00086N $80.00. 070000 Evaporator coil SN 00068N and after 60.00. 0600 Fan motor, evaporator.00. 070000 Bracket, evaporator fan motor.00. 0900098 Fan blade, evaporator, blade (black plastic).00. 07000 Evaporator fan box back, prior to SN 00086N.00 6. 070006 Evaporator fan box back, SN 00086N and after.00 7. 07000 Temperature control mounting bracket, prior to SN 00086N 0.00 8. 070006 Thermostat, includes knob, plate, and tubing 70.00 9. 070006 Defrost sensor.00 0. 0700069 Defrost heater 60.00. 070008 Evaporator housing, prior to SN 00086N 60.00 070006 Evaporator housing, SN 00086N and after 60.00. 07000 Evaporator mounting bracket.00. 070008 Cover, front, evaporator, prior to SN 00086N.00 070006 Cover, front, evaporator, SN 00086N and after.00 070008 Cover, bottom, evaporator, prior to SN 00086N.00 0700060 Cover, bottom, evaporator, SN 00086N and after.00 070007 Tubing, capillary,.09x6" 0.00. 06007 0-" x /" thumbscrew ( required) ( required prior to SN 00086N).00 ea. 8 Unit prior to SN 00086N SN 00068N and after 0 7 6 9 7

Electrical Components Part No. Description Price. 060097 Power cord, exterior, " long $.00 0700099 Replacement power cord assembly, includes (06007, 0000669, 060097) 0.00. 070006 Decal, control module 7.00. 060097 Automatic defrost.00. 070006 Manual defrost timer (6 hr) 90.00. 00007 Receptacle, wire, mate-n-lok.00 6. 06006 Receptacle, 6 wire, mate-n-lok.0 7. 060009 Receptacle, compressor.00 8. 070007 Manual defrost switch 0.00 9. 0700066 Evaporator fan relay 6.00 0. 070007 Manual defrost light, red 0.00 9 9 8 6 0 7 8

0 Volt Electrical Parts Part No. Description Price 070008 Compressor, / HP, 0/0Hz, R0A $70.00 060079 Start capacitor, for / HP R0A and R compressor, 0/0Hz.00 060079 Relay, compressor, / HP, 0V/0Hz, R0A 0.00 060079 Overload for / HP R0A compressor, 0/0Hz.00 0600 Motor, condenser fan, 9 watt, 0V 0/60 Hz 0.00 06008 Motor, evaporator fan, 0V 7.00 0700070 Defrost heater, 0V.00 060098 Defrost timer, automatic, 0V, 0 cycle.00 070007 Defrost timer, manual, 0V, 0 cycle, 6 hour 0.00 000086 Light, red, 0V.00 0700067 Relay, evaporator fan, 0V 7.0 Shelving and Related Parts Part No. Description Price. 070009 8" shelf bracket ( required) $0.00. 070000 " shelf bracket ( required) 6.00. 070009 Shelf, 9-/8" x 9-/8", bottom and middle ( required) 0.00. 0700060 Shelf, 9-/6" x 9-/8", top ( required).00 070006 Shelf kit (070009 =, 0700060 = ).00. 06007 0-" x /" thumbscrew, ss.00 MFV = MFV = Entire Shelving kits for: MFV = 070006 9

Doors, Tops, and Related Parts Part No. Description Price. 06006 Door handle, mirror finish stainless steel $60.00 06006 Door handle, polished brass 0.00 070008 Door, black vinyl-clad 08.00. 070009 Door, stainless steel 08.00 070000 Door, unlaminated 08.00 07000 Door, laminated 0.00 0700096 Door, glass, black, triple pane (replaces 070007 and 070007, heated glass doors) 688.00 0700096 Door, glass, stainless, triple pane (replaces 070007 and 070007, heated glass 78.00 doors) 07000966 Door, glass, laminate, triple pane, right (0700076 - heated door, discontinued) 808.00 0700096 Door, glass, laminate, tripe pane, left (0700077 - heated door, discontinued) 808.00. 060070 Top, stainless steel 0.00 070006 Top, laminated 8.00 06006 Door lock, stainless 6.00 0600009 Key, #806, for stainless cooler lock (06006).00 0600 Door lock, brass.00 060000 Key, #606, for brass cooler door lock (0600).00. 070006 Lock bracket.00. 06007 Hinge set and brackets, right (complete with screws).00 06007 Hinge set and brackets, left (complete with screws).00 0700067 Lock bracket for wood door.00 06006 Hinge set and brackets, for wood door, right (complete with screws) 0.00 0700068 Hinge set and brackets, for wood door, left (complete with screws) 0.00 6. 060069 Bushing, cooler door hinge (black).00 7. 06008 asher, nylon, cooler door hinge.00 8. 07000* Gasket, door, MFV, black, -/" x " OD (*Heated glass door).00 06007 Gasket, door, -/" x " OD, triple pane glass door, after 0/07.00 6 7 8 0

Refrigeration Compartment Covers Part No. Description Price 070000 Front, black vinyl-clad $.00. 070000 Front, stainless steel 8.00. 0700006 Back, black vinyl-clad 0.00 0700007 Back, stainless steel 80.00. 0700078 Side, left, stainless steel 80.00 0700078 Side, left, black vinyl-clad 0.00. 07000786 Side, right, stainless steel 80.00 0700078 Side, right, black vinyl-clad 0.00 Front view Front view Rear view

Glastender, Inc. warrants all products to be free of defects in material and workmanship. One-year labor and parts warranty applies to all glasswashers, self-contained refrigeration models, and BDS model bottle disintegration units. In established areas, a start up is included with GT- and GT-0 model glasswashers. arranty is effective for one year from the date of installation or up to 8 months from date of factory shipment, whichever occurs sooner. Glastender, Inc. will replace any part or assembly found defective under normal use and service. For warranty labor claims beyond months from the date of factory shipment, proof of date of installation or occupancy must be provided. Authorization for labor must be obtained from Glastender within the warranty period and prior to the service being performed. Labor warranty applies to the United States and Canada only. Remote refrigeration models and beer line chillers include a one-year parts warranty only. There is no labor warranty on these products. Field replacement parts not covered under the original warranty include a 90-day part warranty from the date of installation. FOUR YEAR ADDITIONAL COMPRESSOR ARRANTY: Glastender will warrant to the original user the compressor for all selfcontained refrigeration models for an additional four years following the regular one-year warranty period. This plan applies to the compressor only. A completed warranty claim form MUST accompany all returned defective parts or assemblies. Upon request, a defective part or assembly must be returned to Glastender, Inc., Saginaw, Michigan, with all transportation and delivery charges prepaid. arranty repairs or replacements will be shipped FOB factory in Saginaw, Michigan. Reimbursement for applicable freight charges covers ground service only. Glastender provides in-warranty repairs during a service company s regular working days and hours. There is no provision for payment of a premium rate during overtime hours. hen warranty service is requested during other than normal working hours, the end user will be charged the premium portion of the overtime rate. The warranty covers substantiated travel expenses for up to hours / 00 miles round trip up to a maximum of $0. Any additional costs due to installations that require extra work, time, or travel to gain access for service are the sole responsibility of the equipment purchaser. Any exceptions to these travel and access limitations must be pre-approved by a factory representative. The warranty does not cover door gaskets, chemical tubing, pump squeeze tubing, and/or any equipment subjected to accidents, freight damage, alterations from the original design, improper power and/or plumbing hookups, improper chemical use, general misuse, or lack of routine required maintenance as determined by Glastender, Inc. Installation, normal control adjustments, general maintenance, correcting an installation error, or service calls that reveal the unit is functioning normally will not be reimbursed under warranty. Condenser coils on self-contained refrigeration products must be cleaned regularly. Failure to provide adequate air flow to a refrigeration unit will void the warranty. Glastender shall not be liable for loss of use, revenue, or profit, or for any other indirect, incidental, special, or consequential damage including, but not limited to, product spoilage or loss. This warranty is conditioned upon Glastender receiving notice of any defect subject to this warranty within sixty (60) days of its discovery by the end user or dealer. All products are warranted only for the initial place of installation. Removal of a product automatically terminates this warranty. arranty Statement APPLICABLE TO ALL PRODUCTS SOLD ITHIN THE UNITED STATES AND CANADA SECOND YEAR EXTENDED PARTS & LABOR ARRANTY: Glastender s one-year parts and labor warranty on self-contained refrigeration units, excluding beer line chillers, can be extended to two years with the purchase of a two year parts and labor warranty. Specify part number ER ($0 net price) when ordering. EXPORT ARRANTY - One year parts only. EXCLUSION OF ARRANTIES EXCEPT AS PROVIDED ABOVE, GLASTENDER MAKES NO ARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED ARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT. LIMITATION OF REMEDIES AND DAMAGES If Buyer makes a valid and timely claim as outlined above, Glastender s liability and Buyer s remedies under this agreement will be limited solely to labor charges authorized and/or replacement or credit, at Glastender s option, with respect to Products returned at Buyer s expense within thirty (0) days after warranty repair. GLASTENDER S LIABILITY ILL IN NO EVENT BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE RETURNED PRODUCTS. GLASTENDER ILL NOT BE LIABLE UNDER ANY CIRCUMSTANCE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, LABOR COSTS EXCEPT AS COVERED UNDER OUR ARRANTY, LOST PROFITS OR THE LOSS OF PERISHABLE PRODUCTS RESULTING FROM THE USE OF OR INABILITY TO USE OUR PRODUCTS OR FROM OUR PRODUCTS INCORPORATION INTO OR BECOMING A COMPONENT OF ANY OTHER PRODUCT. NEITHER PARTY ILL HAVE ANY NEGLIGENCE OR OTHER TORT LIABILITY TO THE OTHER, OR TO ANY THIRD PARTY, ARISING FROM ANY BREACH OF THIS AGREEMENT. GOVERNING LA - JURISDICTION The terms and conditions of an order are to be governed and construed according to the laws of the State of Michigan, without regard to conflict of laws principles. Buyer hereby consents to the jurisdiction and venue of the courts located in Saginaw County, Michigan. No representative, distributor, dealer, or any other person is authorized to modify this warranty. This warranty replaces all other written or verbal warranties. NOTE: Glastender, Inc. s policy of constant quality improvement means that prices, specifications, and policies are subject to change without notice. Questions regarding this warranty should be directed to Glastender s arranty Administrator. 0-9-7 IMPORTANT!! Attention Service Companies Please review the important warranty information on this page. If you believe a service call should be covered by the factory, please call the factory for authorization between 8AM and PM EST, Monday through Friday.

UNPARALLELED UNDERBAR DESIGN & ENGINEERING Expect more more flexibility more features Glastender has the most complete line of bar equipment and the ability to manufacture custom units, giving you virtually unlimited design flexibility. Each piece of equipment is engineered with features that enhance your efficiency, ease your maintenance, and prolong the life of your investment. The flexibility you want. The features you need. Glastender. Expect more. GLASSASHERS COCKTAIL STATIONS COOLERS FROSTERS BEER SYSTEMS