EDS6051...... TUMBLE DRYER USER MANUAL
2 www.electrolux.com Contents Important Safety Instructions Use - - Dryer Safety... Page 2 Fire Hazards... Page 2 - - The Control Panel... Page 6 Operating Sequence... Page 7 - Cleaning the Lint Filter... Page 3 Care And Cleaning... Page 9 Drying Guide... Page 3 Hints... Page 10 Installation Instructions... Page 4 Troubleshooting & Accessories... Page 11 Warranty... Page 15 - Important Safety Instructions DRYER SAFETY FIRE HAZARDS See the serial number sticker located on the bottom of the door opening for voltage information. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. IMPORTANT: If the electrical cord of this appliance is damaged, it must be replaced by the Manufacturer, Authorised Service Agent or similarly qualified person in order to avoid a hazard. These dryers are for drying clothes, towels and linen at home. Do not use them for any other purpose. Lint must not be allowed to accumulate around the tumble dryer. Do not dry unwashed items in the tumble dryer. WARNING: Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. The final part of a tumble dryer cycle occurs without heat (cooling cycle) to ensure that the items are left at the temperature that ensures that the items will not be damaged.
www.electrolux.com 3 EDS6051 10 Nozzle Lint Filter The lint filter is located at the front of your dryer at the bottom of the door opening. Rating Plate Never operate your dryer without the lint filter. Do not allow lint to build around your dryer. A torn or damaged lint filter must be replaced immediately. Overloading can increase lint build-up because the airflow is reduced.
4 www.electrolux.com on top of a front load washing machine using a stacking kit available as an optional extra (not available for all washing machine models). Worktop Mains Cable Water Inlet Hose Worktop Air Inlet Duct Control Panel Door Safety Switch Button Door Handle Outlet Cover Door Exhaust Grille Removable Exhaust Grille (Optional Extra) Water Connection Cold water tap must be installed within 110 cm of your dryer s water inlet and the tap must be 3/4 inch BSP thread for laundry hose connection. Water pressure must be between 200kpa to 800kpa. Use the hose supplied with the dryer. DO NOT USE OLD HOSES. To connect the water inlet to dryer: 1. Turn off cold water supply to washer. Cold water tap
www.electrolux.com 5 2. Remove cold inlet hose from cold water supply. Check rubber seal, replace if worn. 5. Connect the cold inlet hose for the washer and the dryer to the Y-Connector and tighten them. Cold water tap To Washing Machine 3. 4. Turn on cold supply for a short time to run some water into a bucket or container to clear any contaminants in the line. Connect the Y-Connector to the cold water tap. Check rubber seal 6. Turn on the water tap and check for leaks at all connection.
6 www.electrolux.com 6 8 5 4 10 3 9 2 7 1 The dryer is or This button allows you to select 2 options. When a new program is selected while the dryer is already running, the drying process will continue using the settings from the new program. continue unload Iron Aid: This option will help in reducing wrinkles on your clean and dry clothes by using a combination of moisture and warm air function. Maximum load should not exceed 1 kg when this option is selected. This option cannot be combined with any other programs. This option should only be used to reduce wrinkles for clothes which are clean and dry. When this option is selected, all other programs will be suppressed. from
www.electrolux.com 7 Press door safety switch button. To activate this option press and hold the Option and Delay buttons simultaneously until a long beep is heard. To deactivate press and hold the same buttons until a short beep is heard. To obtain the best drying results with small loads it is recommended to use Extra Dry program. For drying delicates and synthetics at lower heat for maximum care of the fabrics. The Delicate setting will cause the heater to cycle on for shorter time than the Normal setting.
8 www.electrolux.com at WARNING: Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. both
www.electrolux.com 9 Care And Cleaning Warning! You must DISCONNECT the appliance from the electricity supply, before you can carry out any cleaning or maintenance work. 5. Clean the filter in the valve with a stiff brush or a towel. External Cleaning Clean the appliance only with soap and warm water. Fully dry all the surfaces. Caution! Do not use alcohol, solvents or chemical products. Cleaning The Water Inlet Filter If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged. It is therefore a good idea to clean it from time to time. To clean the water inlet filters: 1. Close the water tap. 2. Remove the water inlet hose from the water tap. 3. Clean the filter in the inlet hose with a stiff brush. 4. Remove the inlet hose behind the appliance. 6. Re-install the inlet hose. Make sure that the couplings are tight to prevent leakages. 7. Open the water tap.
10 www.electrolux.com Due to variations in dryer load fabric texture and thickness it is possible that not all items will be dried evenly. It you experience uneven dryness on Normal Dry program please use either Extra Dry or Timer Program but be mindful of the type of fabric being dried to avoid overdrying certain types of fabric. Always follow drying instructions attached to the items intended to be dried in a clothes dryer.
www.electrolux.com 11 TROUBLESHOOTING Instructions Important Safety the temperature You have used wet clothes with Iron Aid option. The Iron Aid program reduces wrinkle on dry laundry only. It is not a drying program. Isolated wet spots on fabrics after Iron Aid cycle completed. No water goes out from Nozzle, when Iron Aid cycle is selected. Clothes are slightly damp after using Iron Aid cycle. Water pressure too low - please check that the water pressure is between 200 kpa and 800 kpa. The water tap is closed, please open the water tap. The inlet hose is squashed or kinked, please check inlet hose connection. The filter in the inlet hose is blocked, please clean the inlet hose filter. Refer to relevant paragraph in Care And Cleaning section. The Nozzle is clogged, please contact the Service Centre. Contact the Service Centre if you are still having problems. This is Normal. Iron Aid uses moisture to reduce the wrinkle on fabrics. It is recommended to hang clothes after using this cycle. If your laundry feels wet rather than slightly damp, then the household water pressure is too high. You may need to reduce pressure by installing a pressure reducing valve at Mains water connection to the household. This must be done by qualified plumber. Note: High water pressure is harmful to all appliances in your household that are connected to the water supply ie: washing machine, dishwasher... etc.
12 www.electrolux.com IMPORTANT below: 10. ACCESSORIES
Note www.electrolux.com 13
14 www.electrolux.com
www.electrolux.com 15
www.electrolux.com/shop 808116304-001-032014