Leisure Line Stoves are to be used as supplemental heat only. Do not use this stove as a replacement for a furnace.

Leisure Line Stoves are to be used as supplemental heat only. Do not use this stove as a replacement for a furnace.

NOTES:

Actuation of your CO alarm indicates the presence of CO. Turn off your coal stove immediately and try to find & solve the problem. Open windows and doors to help move the fresh air throughout the house. Intertek Testing, Middleton, WI 53562 CONAM Inspection, Inc., Auburn, MA 01501 TESTED 8/96 (HYFIRE TESTED 12/96) TO ANSU/UL 1482, CSA B366-M1979 CHIMNEY TYPE: MINIMUM 6 INCH DIAMETER APPROVED LOW HEAT RESIDENTIAL TYPE ALL FUEL. CHIMNEY CONNECTOR: 6 INCH DIAMETER 24 GAUGE BLUE OR BLACK STEEL. INSTALL AT LEAST 18 INCHES FROM CEILING. SPECIAL METHODS ARE REQUIRED WHEN PASSING THROUGH A WALL OR CEILING. SEE INSTRUCTIONS AND BUILIDING CODES. SEE INSTRUCTION MANUAL FOR MOBILE HOME INSTALLATION. A B POCONO 30 21 PIONEER 31 18 HEARTH 27 18 ECONO 1* 30 18 ECONO SIDEWINDER 37 18 HYFIRE II* 34 24 USE APPROVED FLOOR PROTECTOR MUST HAVE 1.2 R VALUE CORNER INSTALLATION This does not include the POCONO or HYFIRE POCONO Clearance is 21 on the sides, HYFIRE clearance is 24 on the sides. 12 18 12 HOPPER 18 FRONT CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA

Parts List 1 pc. 60lb. hopper w/blower 1 pc. Hopper lid 1 pc. Hopper gasket 1 pc. Feeder (burner, 70,000 BTU input) 1 pc. Firestop 2 pc. Thermostat Tools Needed 1-7/16 wrench or socket Connect marked wires on black box of the Thermostat and burner. (DO NOT use green marked wire). Hopper lid sweat is a sign of poor draft. Correct problem immediately!!!

Testing Results All Leisure Line Stoves are Tested To Underwriters Laboratories Standard #1482 By Conam Inspection, Auburn, MA 01501 Tested 8/96 to Ansi/UL 1482, CSA B366-M1979 Intertek Testing, Middleton, WI 53562 U.S. Environmental Protection Agency This heater is only for burning coal. Use of any solid fuel except coal ignition purposes is a violation of Federal Law. This product is Approved for Mobile Homes Proper clearances must be held. The stove must be secured to a non-combustible floor. A fresh air supply (outside) must be brought into the burner unit. Three (3) inch plastic pipe is recommended. Parts List 1 pc. 70lb. hopper 1 pc. Hopper lid 1 pc. Hopper gasket 1 pc. Feeder (burner, 90,000 BTU input) 2 pc. Thermostat Box 1 pc. A125/212 cfm blower 1 pc. Firestop 1 pc. Door Cover Tools Needed 1-3/8 Wrench 1-7/16 Wrench Prevent House Fires Install and Use Only in Accordance with the Manufacturer s Instructions and Local Building Codes. Always use a CO detector!! Safety First Place a CO detector on every floor of your house!!!

Connect marked wires on black box of the Thermostat and burner. (DO NOT use green marked wire). Hopper lid sweat is a sign of poor draft. Correct problem immediately!!!

Trouble Shooting Black Dust: Dirty coal, use caution when adding coal to the hopper Try oiled coal Turn off your fan when adding coal Parts List 1 pc. 110lb. hopper (Pioneer LE) 1 pc. 200lb. hopper (Pocono) 1 pc. Hopper lid 1 pc. Hopper gasket 1 pc. Feeder (burner, 90,000 BTU input) (for Pioneer) 1 pc. Feeder (burner, 110,000 BTU input) (for Pocono) 2 pc. Thermostat Box 1 pc. 265 cfm blower (Pioneer LE) 2 pc. 265 cfm blowers (Pocono) 1 pc. Firestop 1 pc. Door Cover Tools Needed 1-7/16 wrench or socket Sulfur Fumes: Make sure your chimney is clean Make sure all your pipes are clean Make sure the flue cap on your chimney is not too close to the top of the chimney and restricting draft. Make sure the clean-out door to the chimney is closed tight Make sure all door gaskets are intact and in good repair Make sure coal is not excessively wet Make sure the barometric damper is in good working order and not sticking open. Replace if needed. Make sure the stove is maintaining a draft Sweat on the hopper lid is a sign of poor draft Preheat chimney

Connect marked wires on black box of the Thermostat and burner. (DO NOT use green marked wire). Hopper lid sweat is a sign of poor draft. Correct problem immediately!!!

Assembly for Hyfire II A Carbon Monoxide detector must be used!!! Parts List 1 pc. 200lb. hopper 1 pc. Hopper lid 2 pc. Hopper gasket 1 pc. 180 BTU feeder (Hyfire II, 90,000 & 90,000 BTU input) 2 pc. Thermostat Box 2 pc. 265 cfm blowers (fans) 2 pc. Firestop Tools Needed 1-7/16 socket w/extension

The next step is to mount the black thermostat box. The black thermostat can be mounted on either side of the hopper. Holes provided on every hopper. Now install the glass. Place the self-adhesive gasket on both sides of the glass. Wrap the glass completely with the gasket. Take the 4 glass bolts and brackets out of the backside of the door. Install the glass and replace and snug the bolts. Connect marked wires on black box of the Thermostat and burner. (DO NOT use green marked wire). With your assembly finished, it is time to make all the final connections. Your thermostat should, at this point, be mounted. Make sure that your thermostat wire is connected to both the black box, as well as the unit that mounts on the wall. Hopper lid sweat is a sign of poor draft. Correct problem immediately!!!