Planning and Design Guide 2002 Vrs 2.0 DISHWASHERS WASHERS DRYERS ACCESSORIES INSTALLATION S Dimensions & Technical Data D1706...2 D1716...3 D1776...4 D1976...5 Changing Standard Front Panels...6 D1796FI and D1996FI...7 Fitting the D1796FI and D1996FI Custom Door Panel...8 D1796FI and D1996FI Custom Panel Installation Options...9 D1996HNDL...10 D1996SS...11 Optional Accessories...12 Fully Integrated Fill Strip Installations...13 This planning guide provides unit dimensions, cutout dimensions, and utility locations only. For more details, refer to the installation instructions that are supplied with the unit. ASKO LAUNDRY Washers: Dimensions & Technical Data W6021...15 W6441...16 W6661...17 Dryers: Dimensions & Technical Data T701...18 T721...19 T731...20 T761...21 T781...22 Stacked Pair Installations W6021/W6441 and T701...23 W6021/W6441 and T721...24 W6441 and T731...25 W6661 and T761...26 W6661 and T781...27 Cabinet/Closet Installations Stacked Installations...28 Single Unit Installations...29 Side-by-side Installations...30 Optional Accessories...31
32-1/4" to 35-1/2" 819 to 902 mm MODEL D1706 UNIT DIMENSIONS Depth 23-7/16"* 596 mm Depth w/door open 46-1/2"* 1181 mm Weight 104 lb 48 kg TECHNICAL DATA Electricity 120V, 60Hz, 15 amp Water pressure 18-176 psi Heating element 1400 watt Max loading 1600 watt 46-1/2"* 35-1/2" 902 mm FRONT PANELS The front panels on Model D1706 (except the stainless steel model) can be covered or replaced with wood panels. See page 6 for instructions on how to change the front panels. CUTOUT DIMENSIONS Depth 23-7/16" 596 mm *This depth allows a 1" (25 mm) space for the high-loop drain hose. NOTE: Maintain a 1/8" (3 mm) minimum clearance between unit and cabinet. 2" 50mm 6-1/4" to 8-1/4" 159-210 mm 23-7/16" 596 mm The electrical and water supplies should enter through the area indicated by the shaded area. Preferably, they should come through the right side of the machine. The access hole must be round and smooth and no bigger than 2" in diameter. EASYINSTALL SYSTEM Every ASKO dishwasher comes with the unique EasyInstall System that speeds the installation and reduces problems. This system has these components which are approved by regulatory authorities (cul): Over 5' of Pex hose that replaces the water-inlet copper tubing. It has a 3/8"- compression fitting that mates with the shut-off valve. Over 6' of drainhose with an adaptable drain connection.the high loop is built into this hose on the back of the unit. If this loop is removed to lengthen the hose, another high-loop must be built into the installation somewhere along the line (typically where the hose passes through the cabinet). A 6' long electrical cord with standard, 3-pronged, 110V plug. This eliminates the need to wire anything under the unit. 2 Specifications are subject to change without notice. See installation instructions for additional details.
32-1/4" to 35-1/2" 819 to 902 mm MODEL D1716 UNIT DIMENSIONS Depth 23-7/16"* 596 mm Depth w/door open 46-1/2 * 1181 mm Weight 104 lb 48 kg TECHNICAL DATA Electricity 120V, 60Hz, 15 amp Water pressure 18-176 psi Heating element 1400 watt Max loading 1600 watt 46-1/2"* 35-1/2" 902 mm FRONT PANELS The front panels on Model D1716 (except the stainless steel model) can be covered or replaced with wood panels. See page 6 for instructions on how to change the front panels. CUTOUT DIMENSIONS Depth 23-7/16" 596 mm *This depth allows a 1" (25 mm) space for the high-loop drain hose. NOTE: Maintain a 1/8" (3 mm) minimum clearance between unit and cabinet. 2" 50mm 6-1/4" to 8-1/4" 159-210 mm 23-7/16" 596 mm The electrical and water supplies should enter through the area indicated by the shaded area. Preferably, they should come through the right side of the machine. The access hole must be round and smooth and no bigger than 2" in diameter. EASYINSTALL SYSTEM Every ASKO dishwasher comes with the unique EasyInstall System that speeds the installation and reduces problems. This system has these components which are approved by regulatory authorities (cul): Over 5' of Pex hose that replaces the water-inlet copper tubing. It has a 3/8"- compression fitting that mates with the shut-off valve. Over 6' of drainhose with an adaptable drain connection.the high loop is built into this hose on the back of the unit. If this loop is removed to lengthen the hose, another high-loop must be built into the installation somewhere along the line (typically where the hose passes through the cabinet). A 6' long electrical cord with standard, 3-pronged, 110V plug. This eliminates the need to wire anything under the unit. Specifications are subject to change without notice. See installation instructions for additional details. 3
32-1/4" to 35-1/2" 819 to 902 mm MODEL D1776 UNIT DIMENSIONS Depth 23-7/16"* 596 mm Depth w/door open 46-1/2"* 1181 mm Weight 104 lb 48 kg TECHNICAL DATA Electricity 120V, 60Hz, 15 amp Water pressure 18-176 psi Heating element 1400 watt Max loading 1600 watt 46-1/2"* 35-1/2" 902 mm FRONT PANELS The front panels on Model D1776 (except the stainless steel model) can be covered or replaced with wood panels. See page 6 for instructions on how to change the front panels. CUTOUT DIMENSIONS Depth 23-7/16" 596 mm *This depth allows a 1" (25 mm) space for the high-loop drain hose. NOTE: Maintain a 1/8" (3 mm) minimum clearance between unit and cabinet. 2" 50mm 6-1/4" to 8-1/4" 159-210 mm 23-7/16" 596 mm The electrical and water supplies should enter through the area indicated by the shaded area. Preferably, they should come through the right side of the machine. The access hole must be round and smooth and no bigger than 2" in diameter. EASYINSTALL SYSTEM Every ASKO dishwasher comes with the unique EasyInstall System that speeds the installation and reduces problems. This system has these components which are approved by regulatory authorities (cul): Over 5' of Pex hose that replaces the water-inlet copper tubing. It has a 3/8"- compression fitting that mates with the shut-off valve. Over 6' of drainhose with an adaptable drain connection.the high loop is built into this hose on the back of the unit. If this loop is removed to lengthen the hose, another high-loop must be built into the installation somewhere along the line (typically where the hose passes through the cabinet). A 6' long electrical cord with standard, 3-pronged, 110V plug. This eliminates the need to wire anything under the unit. 4 Specifications are subject to change without notice. See installation instructions for additional details.
32-1/4" to 35-1/2" 819 to 902 mm MODEL D1976 UNIT DIMENSIONS Depth 23-7/16"* 596 mm Depth w/door open 46-1/2"* 1181 mm Weight 104 lb 48 kg TECHNICAL DATA Electricity 120V, 60Hz, 15 amp Water pressure 18-176 psi Heating element 1400 watt Max loading 1600 watt 46-1/2"* 35-1/2" 902 mm FRONT PANELS The front panels on Model D1976 (except the stainless steel model) can be covered or replaced with wood panels. See page 6 for instructions on how to change the front panels. CUTOUT DIMENSIONS Depth 23-7/16" 596 mm *This depth allows a 1" (25 mm) space for the high-loop drain hose. NOTE: Maintain a 1/8" (3 mm) minimum clearance between unit and cabinet. 2" 50mm 6-1/4" to 8-1/4" 159-210 mm 23-7/16" 596 mm The electrical and water supplies should enter through the area indicated by the shaded area. Preferably, they should come through the right side of the machine. The access hole must be round and smooth and no bigger than 2" in diameter. EASYINSTALL SYSTEM Every ASKO dishwasher comes with the unique EasyInstall System that speeds the installation and reduces problems. This system has these components which are approved by regulatory authorities (cul): Over 5' of Pex hose that replaces the water-inlet copper tubing. It has a 3/8"- compression fitting that mates with the shut-off valve. Over 6' of drainhose with an adaptable drain connection.the high loop is built into this hose on the back of the unit. If this loop is removed to lengthen the hose, another high-loop must be built into the installation somewhere along the line (typically where the hose passes through the cabinet). A 6' long electrical cord with standard, 3-pronged, 110V plug. This eliminates the need to wire anything under the unit. Specifications are subject to change without notice. See installation instructions for additional details. 5
CHANGING THE STANDARD FRONT PANELS The front panels on Models D1706, D1716, D1776 and D1976 (except the stainless steel models) can be replaced with wood panels. 1" 25 mm Upper Panel 1" 25 mm PANEL DIMENSIONS For standard, non-raised panels, use 1/16" to 1/4" material. For custom raised panels, the decor trim will accept up to 1/4" flange. The raised panel can be mounted on a backing sheet cut to fit as shown on the right. NOTE: The stainless steel panels do not have holes for custom trim. You have to drill the holes. 1" 25 mm 17-15/16" 456 mm Raised area 21-3/16" 538 mm INSTALLING THE PANEL WARNING!Before working on any electrical appliance, be sure the electrical power has been turned off at the breaker/fuse box. Refer to the illustration at bottom right for instruction references. 1. Remove the lower access panel with standard or 20 torx screwdriver. 2. Carefully remove the plastic plugs around the edges of the access panel and upper door panel. You may discard the plugs. 3. Using the screws provided with the trim kit, loosely secure parts A and C to the upper door panel. 4. Slide the upper panel into the trim kit grooves. 5. Tighten the screws holding parts A and C. 6. Secure part B and tighten screws. 7. Loosely screw part E to the lower access panel. 8. Slide the custom panel into trim kit channels and tighten the screw to part E. 9. Secure part D of the trim kit and tighten the screws. 10. Secure the lower access panel to the dishwasher. 11. Drop the lower access panel to line up with the lower holes on the guard plate and secure the screws. (Make sure the exhaust vent is below the panel. Otherwise, steam from the vent could eventually damage the panel.) 12. Before you push the dishwasher into the cabinet opening, test the door to make sure it opens properly, (The door is counter-balanced, so it should remain in any position.) If it doesn t, you may need to adjust the door springs (see page 8). 13. Fasten the dishwasher to the cabinet. 2-1/4" 57 mm 1" 25 mm 2-3/16" 56 mm 1" 25 mm E 1" 25 mm 23-3/16" 589 mm 1/4" PANEL TRIM KIT A C D 21-3/16" 538 mm Lower Panel Raised area 23-3/16" 589 mm 21-3/16" 538 mm Trim kit part numbers: White: 8070850-0 Black: 8070850-29 B 1" 25 mm 4-3/16" 106 mm 6 Specifications are subject to change without notice. See installation instructions for additional details.
32-1/4" to 35-1/2" 819 to 902 mm MODEL D1796FI AND D1996FI UNIT DIMENSIONS Height 32-1/4" 35-1/2" 819 902 mm Width 23-1/2" 597 mm Depth 23-7/16" 596 mm Depth w/door open 46-1/2" 48-1/4 * 1181 1226 mm Weight 104 lb 48 kg TECHNICAL DATA Electricity 120V, 60Hz, 15 amp Water pressure 18-176 psi Heating element 1400 watt Max loading 1600 watt 23-1/2" 603 mm 46-1/2" - 48-1/4"* 1181-1226 mm 32-1/4" - 35-1/2" 819-902 mm CUSTOM FRONT PANELS The D1796FI and D1996FI can only be installed with a fully-integrated custom door panel that extends from the toe kick to the counter top. A one-piece custom door panel with a curved handle is available for 4-inch toe kick installations (see page 12). Refer to page 8 for instructions on how to install the custom panels. CUTOUT DIMENSIONS Width 23-3/4" 603 mm Depth 23-7/16" 596 mm *For fully-integrated installations, the dishwasher s total depth with the door open can vary depending on the height of the toe kick. The total depth for a 4" toe kick is 48-1/4", a 6" toe kick is 46-1/2". This depth varies from the standard 46-1/2" because in a 4" toe kick installation the door panel is typically extended 1-3/4" beyond the door (control panel) and this lengthens the door. See page 9 for details. NOTE: Maintain a 1/8" (3 mm) minimum clearance between unit and cabinet. 2" 50mm 6-1/4" to 8-1/4" 159-210 mm 23-7/16" 596 mm 23-3/4" 603 mm The electrical and water supplies should enter through the area indicated by the shaded area. Preferably, they should come through the right side of the machine. The access hole must be round and smooth and no bigger than 2" in diameter. EASYINSTALL SYSTEM Every ASKO dishwasher comes with the unique EasyInstall System that speeds the installation and reduces problems. This system has these components which are approved by regulatory authorities (cul): Over 5' of Pex hose that replaces the water-inlet copper tubing. It has a 3/8"- compression fitting that mates with the shut-off valve. Over 6' of drainhose with an adaptable drain connection.the high loop is built into this hose on the back of the unit. If this loop is removed to lengthen the hose, another high-loop must be built into the installation somewhere along the line (typically where the hose passes through the cabinet). A 6' long electrical cord with standard, 3-pronged, 110V plug. This eliminates the need to wire anything under the unit. Specifications are subject to change without notice. See installation instructions for additional details. 7
FITTING THE D1796FI AND D1996FI CUSTOM DOOR PANEL The D1796FI and D1996FI can only be installed with a fullyintegrated custom door panel that extends from the toe kick to the counter top. The unit comes with everything needed to make installing the door panel easy. The door is predrilled for the panel s mounting screws. The custom panel should be a minimum of 3/4" (19 mm) thick. ITEMS PROVIDED WITH THE UNIT Two 3/8" screws Four 1-3/4" screws Four adhesive-backed plastic spacer washers CUSTOM PANEL DIMENSIONS Width: 23-1/2" (597 mm) Height: 28-1/8" 30-1/8" (714 mm 765 mm) (Measured from the top of the panel to the lower edge of the kitchen cabinet.) Thickness: Minimum 3/4" (19 mm) Weight: Up to 22 lb. INSTALLING THE CUSTOM PANEL Before fitting the custom panel, the dishwasher must be installed underneath the cabinet. After you ve made the required measurements, pull the machine out again to install the panel. Refer to the illustration at right for instruction references. 1. Fit the handle (A) onto the panel according to the manufacturer s instructions. (NOTE: A handle should be used rather than a knob, because a knob does not provide enough grip.) 2. Remove the adhesive protection from the washers and place them in line with the four keyholes (C) on the metal front of the dishwasher door. 3. Loosen the screws (D) on the outer edges of the dishwasher door. 4. Pull the turbo fan exhaust frame (E) down until the lower edge aligns with the lower edge of the cabinets and tighten the screws. Snap the plastic duct into the turbo fan exhaust vent. WARNING!The custom panel must not obstruct the fan exhaust vent; otherwise, steam from the vent could eventually damage the cabinet. 5. The two short screws (B) go into the back of the panel, 16-3/16" (411 mm) from the upper edge of the panel and 5/8" from the outer edges. Insert the short screws into the panel, leaving 1/8" (3 mm) of space between the screw head and the panel. 6. Hook the panel screws (F) into the keyholes (C) on the dishwasher door. 7. Push the panel upwards until the lower edge aligns with the lower edge of the cabinets and secure the screws. WARNING!The custom panel should not extend more than 2-15/16" (75 mm) below the bottom of the dishwasher door; otherwise, it will strike the toe kick and damage the machine and/or the panel. 8 8.Open the door and tighten the screws (F) inside. ADJUSTING THE DOOR SPRINGS Before you push the dishwasher into the cabinet opening, test the door to make sure it stays in place at any angle. If it tends to fall down, pull out the machine and tension the door springs on the sides of the machine by moving them one hole farther back or by twisting the spring to make it shorter. Shorten Specifications are subject to change without notice. See installation instructions for additional details.
D1796FI AND D1996FI CUSTOM PANEL INSTALLATION OPTIONS 4-INCH TOE KICK INSTALLATIONS Custom panels the same height as the dishwasher door If the custom panel is the same height as the dishwasher door, a 2" decorative fill strip or pull-out cutting board must be used to fill the area between the panel and the counter top (as illustrated below). With a 4-inch toe kick installation, the door panel extends 2 inches above the control panel, as illustrated. 1-3/4" (44 mm) 2" decorative fill strip or cutting board If you install the door panel to reach the cabinet top, we recommend that you install a 2" support strip between the upper edge of the dishwasher and the counter to hide the top of the dishwasher and further reduce water noise. A metal fill strip is also available for this type of installation (see page 12). 28-1/8" 714 mm 2-inch support strip 23-1/2" 597 mm 4-inch toe kick Custom panels that extend to cabinet top Another installation option for a 4" toe kick is to extend the custom panel to the cabinet top (as illustrated below), which eliminates the need for a decorative fill strip. A one-piece custom door panel with a curved handle is available for 4-inch toe kick installations (see page 12). Panel extends from toe kick to cabinet top. 4-inch toe kick 6-INCH TOE KICK INSTALLATIONS For 6" toe kick installations, no decorative fill strips or support strips are necessary. Panel extends from toe kick to cabinet top. 30-1/8" 765 mm 23-1/2" 597 mm 4-inch toe kick NOTE: If the cutout is wide, the custom panel can be 23-3/4" wide. Specifications are subject to change without notice. See installation instructions for additional details. 9
32-1/4" to 35-1/2" 819 to 902 mm MODEL D1996HNDL UNIT DIMENSIONS Depth 23-7/16"* 596 mm Depth w/door open 46-1/2"* 1181 mm Weight 104 lb 48 kg 46-1/2"* TECHNICAL DATA Electricity 120V, 60Hz, 15 amp Water pressure 18-176 psi Heating element 1400 watt Max loading 1600 watt 32-1/4" - 35-1/2" 819-902 mm FRONT PANELS Model D1996HNDL is not designed to accept a custom front panel. Even though the controls are on top of the door, this model installs like a standard ASKO dishwasher. It fits in American cabinets (4" toe kick) with a wide opening. CUTOUT DIMENSIONS Depth* 23-7/16" 596 mm *This depth allows a 1" (25 mm) space for the high-loop drain hose. NOTE: Maintain a 1/8" (3 mm) minimum clearance between unit and cabinet. 2" 50mm 6-1/4" to 8-1/4" 159-210 mm 23-7/16" 596 mm The electrical and water supplies should enter through the area indicated by the shaded area. Preferably, they should come through the right side of the machine. The access hole must be round and smooth and no bigger than 2" in diameter. EASYINSTALL SYSTEM Every ASKO dishwasher comes with the unique EasyInstall System that speeds the installation and reduces problems. This system has these components which are approved by regulatory authorities (cul): Over 5' of Pex hose that replaces the water-inlet copper tubing. It has a 3/8"- compression fitting that mates with the shut-off valve. Over 6' of drainhose with an adaptable drain connection.the high loop is built into this hose on the back of the unit. If this loop is removed to lengthen the hose, another high-loop must be built into the installation somewhere along the line (typically where the hose passes through the cabinet). A 6' long electrical cord with standard, 3-pronged, 110V plug. This eliminates the need to wire anything under the unit. 10 Specifications are subject to change without notice. See installation instructions for additional details.
32-1/4" to 35-1/2" 819 to 902 mm MODEL D1996SS UNIT DIMENSIONS Depth 23-7/16"* 596 mm Depth w/door open 46-1/2"* 1181 mm Weight 104 lb 48 kg TECHNICAL DATA Electricity 120V, 60Hz, 15 amp Water pressure 18-176 psi Heating element 1400 watt Max loading 1600 watt 46-1/2"* 1181 mm 32-1/4" - 35-1/2" 819-902 mm FRONT PANELS Model D1996SS is not designed to accept a custom front panel. Even though the controls are on top of the door, this model installs like a standard ASKO dishwasher. It fits in American cabinets (4" toe kick) with a wide opening. CUTOUT DIMENSIONS Depth* 23-7/16" 596 mm *This depth allows a 1" (25 mm) space for the high-loop drain hose. NOTE: Maintain a 1/8" (3 mm) minimum clearance between unit and cabinet. 2" 50mm 6-1/4" to 8-1/4" 159-210 mm 23-7/16" 596 mm The electrical and water supplies should enter through the area indicated by the shaded area. Preferably, they should come through the right side of the machine. The access hole must be round and smooth and no bigger than 2" in diameter. EASYINSTALL SYSTEM Every ASKO dishwasher comes with the unique EasyInstall System that speeds the installation and reduces problems. This system has these components which are approved by regulatory authorities (cul): Over 5' of Pex hose that replaces the water-inlet copper tubing. It has a 3/8"- compression fitting that mates with the shut-off valve. Over 6' of drainhose with an adaptable drain connection.the high loop is built into this hose on the back of the unit. If this loop is removed to lengthen the hose, another high-loop must be built into the installation somewhere along the line (typically where the hose passes through the cabinet). A 6' long electrical cord with standard, 3-pronged, 110V plug. This eliminates the need to wire anything under the unit. Specifications are subject to change without notice. See installation instructions for additional details. 11
OPTIONAL DISHWASHER ACCESSORIES Curved Handle for Fully Integrated Dishwashers 8073718-0 White 8073718-29 Black 8073718-84 Bisque 8073718-82 Brass-Like 8073718-95 Stainless Steel Metal Top Fill Strip Attaches to top of FI units and fills gap between tank and counter top. 8073869-95 FI Side Fill Strips, Stainless Steel Fills gap when FI unit installed in wide opening. Kit includes both left- and right-side strips. 8075045-95 One-Piece Door with Handle Only available for D1796FI and D1996FI One-piece door with matching one-piece, curved handle. These doors cannot be used in ADA (<34") installations. 8072856 0 White 8072856 84 Bisque 8072856 29 Black 8072856 95 Stainless Steel 1/4" Trim Kits Models D1706, D1716, D1776 and D1976 8070850 0 White trim kit for installing 1/4" custom panels 8070850 29 Black trim kit for same installation and units as above European Toe Kick (Two Pieces) 8070121-0 Extension 8057528 0 Toe Kick White European toe kick to accommodate 6" toe space on models D1796FI and D1996FI. Two pieces are 23-1/2" wide. 8070121-29 Extension 8057528 29 Toe Kick Black toe kick for same installation. Two pieces are 23-1/2" wide. European Toe Kick Extension 2.5" Toe Kicks 805SC-W White 805SC-B Black 805SC-SS Stainless Steel 2.5" Toe Kick Dishwasher Tip Guard 8070851 Secures dishwasher when it s not possible to attach it to cabinetry or counter top Two Heavy-Duty Door Springs 7-12 lbs.: 8060232-77 (Yellow) 12-22 lbs: 8071323-77 (Red) (Standard on all FI dishwashers) Provide additional support for custom panels Replacement Dishwasher Baskets 8801200 36 8801199 36 Lower basket for all models; has removable tines Upper basket for all models; has a split cup rack and a stemware rack 12 Specifications are subject to change without notice. See installation instructions for additional details.
FILL STRIPS INSTALLATION INSTRUCTIONS AVAILABLE ACCESSORIES ASKO offers accessories for the fully integrated (FI) dishwasher to give installations in American cabinetry a clean and complete look. The available accessories are: Top Fill Strip Side Fill Strip One-Piece Door Panels Fills the gap between the dishwasher and the bottom of the countertop. 8073869-95 Fills the gap between the side of the dishwasher and the cabinet. 8074248-95 Right 8074249-95 Left Available in white, black, bisque and stainless steel. We also offer a brass-like handle. INSTALLATION INSTRUCTIONS Figure 1. Attaching Top Fill Strip 1. If you are installing the dishwasher with either the top fill strip or side fill strips, you must remove the insulation strips. These are the black sponge strips attached to the front edge of the tank, from top to bottom. To remove them, simply grip the top or bottom edge and pull it away from the tank, as illustrated in Figure 1. 2. If you are installing the top fill strip, you must remove the black rubber strip attached to the flange of the tank. Simply grip one end of the rubber strip and pull it away from the flange, as illustrated in Figure 2. 3. Remove the fill strip and two mounting screws from the package. 4. The top fill strip has a slot that runs from side to side. This slot faces the front of the dishwasher. Set the fill strip on top of the dishwasher where you removed the insulation and rubber strip. 5. Slide the strip forward, having the flange of the dishwasher and the top mounting brackets slide through the slot on the front of the trim strip until the strip is flush with the dishwasher tank, as illustrated in Figures 3 and 4. (If it does not pull forward far enough to be flush, it will not secure to the dishwasher.) 6. Open the dishwasher door and insert the mounting screws as if you were going to mount the dishwasher to the cabinet, as illustrated in Figure 5. Figure 5. Figure 2. Figure 3. Figure 4. Specifications are subject to change without notice. See installation instructions for additional details. 13
FILL STRIPS INSTALLATION INSTRUCTIONS Attaching Side Fill Strips 1. If you are installing the dishwasher with the side fill strips, you must remove the insulation strips. These are the black sponge strips attached to the front edge of the tank, from top to bottom. To remove them, simply grip the top or bottom edge and pull it away from the tank, as illustrated in Figure 6. 2. The trim strip has multiple mounting holes. Align the largest hole with the same size hole on the side of the dishwasher, as illustrated in Figure 7. (This hole is used when you anchor the dishwasher to the cabinet.) 3. Keeping the trim strip aligned with the holes, open the dishwasher door and secure it to the dishwasher with the screws provided, as illustrated in Figure 8. (The screw head should be inside the tank.) 4. When anchoring the dishwasher to the cabinet, height adjustments is essential to properly align the panel with the cabinet facings. Figure 6. Figure 7. NOTES: Be sure to order a side fill strip for each side (left and right). The unit will accept various sized panels. Refer to the dishwasher specifications before building the panel so it will correctly align with the cabinet facings. If a four-inch toe kick is used, the unit must be installed at its lowest height. (The dishwasher is delivered at its lowest height.) On four-inch toe kick installations, the one-piece door panel will extend past the top of the control panel approximately 1-3/4". Figure 8. 14 Specifications are subject to change without notice. See installation instructions for additional details.
THE AWARDS JUST KEEP STACKING UP. W660 and T760 for 2000 W600 for 2001 91 % 0F HOUSEHOLDS SAY ASKO IS QUIETEST. Dishwashers selected by 91% of homeowners as the quietest in independent tests. D1996FI Dishwasher 1805 Dishwasher Excellence In Design Innovation All ASKO products are covered by the Good Housekeeping Seal. W660 Washer & T760 Dryer ASKO dishwashers and washers meet the Energy Star requirements. W660 Washer & T760 Dryer 2000 W6661 Washer & T761 Dryer 2002 BUILT TO LAST LONGER www.askousa.com ASKO Inc. P.O. Box 851805 Richardson, Texas 75085-1805 Advisory Center: 800-898-1879 Underwriters Laboratories, Inc. Printed on Recycled Paper ASKO Inc. retains the right to vary the model specifications at any time. All facts were accurate at time of printing. Before purchasing any ASKO product, read important energy cost and efficiency information available from retailer. ASKO Inc. 2002 Form 073017-0602