TECHNICAL MANUAL BIOTEC 25 AND BIOTEC 40

INDEX INDEX Safety information.......4 Technical data...5 Boiler features...6 Technical information........7 Fuel...... 8 Construction and function...... 9 Hydraulic Schemes...10 & 11 Installation.. 12 & 13 Boiler controller...14, 15 & 16 Control parameters...17, 18 & 19 Operational phases.........20 Maintenance... 21 Possible faults... 23 Commissioning...23 Relocating and boiler disposal... 24 Guarantee......24 Terminal connections......25 Strebel will not be liable for Typographical and printing errors, changes in construction and dimensions which are stated throughout this manual. 3

Safety information Basics The boiler must be installed by a competent professional. The Biotec is manufactured according to current safety standards. If safety rules are ignored, injury or even death of the user could result. Damage to the boiler and accessories can result if the manual and safety instruction are not adhered to.. The specialist responsible for the installation must explain the proper handling of the boiler to the user. Only use the boiler if it is installed properly. Always follow the instructions of this manual. Any boiler failure must be repaired as soon as possible. Use of the boiler The manufacturer is not responsible for damages resulting from incorrect use. The appliance must be installed in accordance with local building regulations as appropriate to the country in which the boiler is being installed. The operational parameters and adjustments can only be modified with the approval of Strebel ltd. The use of parameters and adjustments outside the approved range can cause damage or faults to the Boiler, accessories and or the system. Prescribed fuel This boiler is designed for the combustion of wood pellets. The use of other fuels is prohibited. Wood pellets are cylindrical and made from wood without additives or chemical binders. The pellets must have specific dimensions ( as below) and a low moisture level. STREBEL recommends pellets with a diameter of 6 to 8 mm and length of 10 to 30 mm. Quality and form are as per standards ÖNORM 7135 and DIN 51731. Only use pellets that comply with ÖNORM, DIN ENplus or equal. More information on page 8. Signs and symbols Possible risks Carbon monoxide During boiler operation, carbon monoxide can emit through the boiler doors when they are DANGER open. Only leave the boiler doors open as long as necessary. Insufficient ventilation during boiler operation can cause death. Closing the ventilation openings of the boiler room or the boiler is prohibited. Please adhere to BS 6798 & BS5440:2 Wood requires one and a half times the ventilation needed for gas. Surfaces with high temperatures Touching hot surfaces can cause burns. Surfaces marked with this symbol may only be touched when the system is fully cooled down. Text passages with this symbol hold information relating to hot boiler parts. SAFETY INFORMATION Possible Injury Working on parts marked with this symbol can cause injury. Text showing this symbol give safety information where applicable Possible hand injuries Working on parts marked with this symbol can cause hand injuries. Fire hazard Flammable items must not be positioned near the boiler. Text passages with this symbol give information about fire prevention. Danger of frost Frost forming in the system pipes during cold weather can cause severe damages. Text passages with this symbol contain information relating to frost prevention. Additional information or advice Adhere to local and national regulations concerning positioning, installation, operation and disposal of the boiler. Every person intending to operate the boiler is advised to carefully read this manual especially to the safety information. Persons intending to clean the boiler or perform other maintenance must read this manual otherwise the warranty is invalid. Risk of electric shock Sections marked with this symbol are only to be carried out by an electrician. Text showing this symbol give information about electrical connections. 4

TECHNICAL DATA Biotec 25 Biotec 40 NOMINAL OUTPUT KW 25 40 MINIMUM OUTPUT KW 8 13 MAXIMUM BOILER TEMPERATURE C 90 90 MINIMUM BOILER TEMPERATURE C 70 70 FLUE TEMPERATURE MAXIMUM OUTPUT C 135 140 FLUE TEMPERATURE MINIMUM OUTPUT C 95 95 FLUE EXHAUST GAS FLOW RATE MAX OUTPUT Kg/Sec 0.0176 0.0280 FLUE EXHAUST GAS FLOW RATE MIN OUTPUT Kg/Sec 0.0079 0.0140 EFFICIENCY % 91 85 BOILER WATER CONTENT LTR 74 118 HYDRAULIC RESISTANCE DELTA T 10 C mbar 7 7 HYDRAULIC RESISTANCE DELTA T 20 C mbar 2 2 BOILER WEIGHT Kg 340 459 BOILER CLASS EN303-5 3 3 MAXIMUM OPERATING PRESSURE BAR 2.5 2.5 MAXIMUM TEST PRESSURE BAR 5 5 MAXIMUM CHIMNEY (DRAUGHT) NEGATIVE PRESSURE PA 12 15 FLOW & RETURN CONNECTION SIZE INCH 1 1¼ FLUE CONNECTION DIAMETER mm 130 130 MAXIMUM CAPACITY OF THE STANDARD PELLET HOPPER Kg 120 170 ELECTRICAL SUPPLY/AMPERAGE 230V 50HZ MAX 1 AMP 230V 50HZ MAX 1 AMP WATTAGE DURING NORMAL OPERATION W 100 123 WATTAGE DURING IGNITION PHASE W 300 323 Data subject to change without notice. 5

BOILER FEATURES 1 Boiler features 1.1 General information The Biotec Boiler has a modern design and is made of high quality material. The boiler tests were carried out conforming to EN 303-5, therefore the boiler fulfils all requirements for the connection to a central heating system. The maximum permitted system pressure is 2.5 bar. This boiler is suitable for central heating system of familyhomes, small businesses or workshops. The automatic operation is very user-friendly, because the only action during operation is re-filling the pellet silo depending on the usage. The Biotec includes the silo and pellet screw with the silo on the right hand side. The silo can be mounted on the left hand side on application and at extra cost. 1.2 Conformity declaration The company STREBEL confirms according to EN45014:1998 tha the boiler Biotec complies with the following standards: EC-guidelines: MD 98/37/EC PED 97/23/EC LVD 2006/95/EC EMC 2004/108/EC General standards: EN 303-5:1999; EN 60204-1:2006; EN 60335-1:2002; EN 50165:1997+A1; EN 61000-6-3:2001; EN ISO 12100-1:2003; EN ISO 12100-2:2003; EN 1050:1997 Other standards and technical specifications: EN 287-1:2004, EN 288-3:1992; EN 10204:2004; EN ISO 7000:2004. Testing method conformity: Module B1 Limit of Emission combustion products (class) 3 Certificates: EC Control Type Certificate Nr. 0745/350/09 STREBEL Responsible laboratory: TÜV Thüringen e.v. Service- Centre South Germany, Industry.13, D-98544 in the town Zella Mehlis We hereby declare that the stated products were produced under safety and specific guidelines and standards. All working conditions and terms of use comply with this manual. Wood pellets are an excellent renewable fuel they are cylindrical in shape with a low ash-percentage after combustion which accounts for about 1 %. The caloric value of pellets is approx. 18000 kj/kg, which means that 2 kg pellets is roughly equivalent to 1 ltr of light heating oil. If the product is changed and changes are unapproved by Strebel the above confirmation loses its validity. The storing qualities and the high energy value of pellets make them the ideal replacement for oil or gas. 6

TECHNICAL INFORMATION SIDE VIEW R2 R1 D H C G R1 R3 F B E A TOTAL WIDTH WITH TOTAL HEIGHT FLUE DIA BOILER BODY RETURN FLOW FLUE HOPPER DEPTH B C D WIDTH E HEIGHT F HEIGHT G HEIGHT Biotec 25 1226 (200LTR HOPPER) 870 1610 130 500 269 1132 1304 Biotec 40 1560 (300LTR HOPPER) 1104 1660 139 708 254 1301 1311 Flow & Return Vent Drain 25 40 1 1 7

SPECIALIST UK FUEL PROVIDER 3 Fuel 3.1 Strebel Biotec boilers require fuels complying to ENplus-A1 PELLET INFORMATION Information kindly provided by Forever Fuels Pellet-size HP5, made from by-products of wood and wood shavings, without additives. The energy value of 2 kg pellets complies with the energy of 1 l light heating oil (10 kwh). Comply DIN 51731 ÖNORM 7135 The Austrian standard comprises quality requirements of pellets, testing regulations, supervision of pellet production and labelling. DIN Plus Standard DIN Plus combines Standard DIN 51731 and Standard ÖNORM 7135. The certification procedure at the manufacturer s works is carried out by a responsible certified DIN-inspector. The quality of the pellets is supervised and checked regularly. 8

12 11 CONSTRUCTION & FUNCTION 6 12 15 3 13 2 9 7 8 1 Boiler Construction 16 14 Legend: 1.) Combustion chamber 2.) Heat exchanger 3.) Pellet silo 4.) Pellet screw 5.) Gear motor 6.) Heat exchanger top 7.) Air supply 8.) Fan 9.) Burner-door 10.) Flue connection 11.) Flue exhaust probe 12.) Boiler-controller 13.) Exhaust pipe 14.) Ash drawer 4.2 Function The pellets are conveyed from the silo (3) to the burner (1) via the pellet screw (4). The ignition system (16) automatically ignites the pellets during start-up or after an operating pause. The fan (8) supplies the burner with primary and secondary air. The air ducts in the combustion chamber supply the correct amount of air for primary and secondary combustion. NOTE THE PELLET SCREW AND AUGER MEN- TIONED IN THIS MANUAL ARE THE SAME ITEM. 15.) Heat exchanger cleaning system 16.) Ignition system 9

HYDRAULIC SCHEME See your quotation for items that are supplied. Positions & orientation below are for ease of illustration DHW THERMAL VALVE COLD WATER SUPPLY TO REGULATIONS Fill STREBEL TEMPERATURE GAUGE PUMP DRAIN OFF COCK AUTOMATIC 3 PORT MIXING VALVE for maintained return HEAT STORE PRESSURE GAUGE temperature SAFETY ISOLATING VALVE AUTO AIR VENT EXPANSION VESSEL 10

HYDRAULIC SCHEME See your quotation for items that are supplied. Positions & orientation below are for ease of illustration THERMAL VALVE COLD WATER SUPPLY TO REGULATIONS DHW Fill STREBEL TEMPERATURE GAUGE PUMP DRAIN OFF COCK AUTOMATIC 3 PORT MIXING VALVE for maintained return LOW LOSS HEADER PRESSURE GAUGE temperature SAFETY ISOLATING VALVE AUTO AIR VENT EXPANSION VESSEL 11

FLUE DIAMETER IN CM 5.2 Installation of the chimney INSTALLATION The boiler must be installed near a chimney. It is prohibited to close air vents. DANGER Insufficient flue draught can cause a fire which can spread from the burner on to the screw and then to the pellets in the silo. This must not happen however a safety extinguishing valve is fitted as standard. 1.) The boiler must be placed on a solid and stable floor. 2.) The installation must be carried out by qualified technicians and the electrical supply must be to regulations 3.) The boiler room must have a water supply 4) Servicing access should be considered 5) A waste water drain is useful. 6.) The boiler room must have ventilation to current regulations 7) Floor, walls, ceiling, door and equipment of the boiler room must be made of non-flammable material. 8.) Humidity should be kept at a low level to avoid corrosion of metal parts. 9) For filling the boiler we advise the use of soft water. 13 10) The circulation pump must not operate before the heating system is completely filled with water. The system must be bled of air completely 11) When connecting the boiler to the flue it is necessary to make sure that all connections are sealed properly. 12) Before the first start-up, check the position of the combustion chamber bricks. 13) Consider protection from freezing. 1.5 TO 3MT 1500mm FIRE BRICKS 12

INSTALLATION 5.3 Connection of the boiler parts To prevent the system freezing when the boiler is not to be used for a long period of ELECTRICAL time, we advise draining the system. Connect the pump to the power supply. (max. current 1 A). Connection of the controller Connect the controller to the power supply. The installation of the electrical accessories of the boiler need a power supply with 230 V/50 Hz. Connection of the room thermostat A room thermostat can be connected to the controller. Before starting up the boiler, check the following: HYDRAULIC 1.) Water pressure in boiler and system is adequate. 2.) The system must be bled of air 3.) The boiler wiring is installed correctly and is undamaged and not touching surfaces that heat up during operation. 4.) The combustion chamber bricks are correctly positioned 5.) The pellet silo is clean. A certified safety valve (2.5 bar) must be installed in the heating system. Do not install other valves between the safety valve and boiler The return temperature must not fall below 60 C to prevent the build of condensate inside the boiler. When the boiler is not producing heat, other heaters should be in place to protect the Boiler and system from frost where freezing could be imminent 13

BOILER CONTROL 6.2 Basic display 6 Boiler controller 6.1 Control panel The controller is used for regulating the pellet boiler operation and should be set before commissioning The design of the control panel is shown below: 1. IGNITION The controller has an LCD display and 6 buttons on the right side of the display. Functions of the buttons Increase of parameter values Escape, boiler power off Browse menu go back Browse menu go forward Decrease the parameter values Enter, confirm selected parameter 1 2 3 4 Legend 1 Time 1. IGNITION 5 6 7 8 9 2 Boiler operation 3 DHW temperature 4 Fan activated 5 Pump 6 Pellet auger 7 Ignition system 8 Boiler pump 9 Pre-set power output 10 Flue gas temperature 11 Current set boiler temperature 12 Program 13 Boiler operation phase 13 12 11 10 Inputs - Boiler probe (Pt 1000) - Flue gas probe (Pt 1000) - Domestic water probe (NTC, 10 kω) - Heat store probe (NTC, 10 kω) - Room thermostat - Input GSM controller Outputs - Ignition system (relay,8a, NO) - Pellet auger (relay, 5A, NO) - Fan (PWM) EXPLANATION OF THE DISPLAY (legend 13) Boiler operational phase, information about the current phase of boiler operation Boiler OFF, First ignition-phase, Combustion-phase, Cooldown phase, Room thermostat,off etc. The symbol Boiler operation shows if the boiler is active or not. If the boiler is set to run in a pre-programmed operation mode, the display shows TIME. The symbols in the bottom line show the operational availability of the controller outputs such as fan, pump, auger, ignition, boiler pump and whether they are active or not. If the symbol shows, that component is active. 14

BOILER CONTROL 6.3 Start and stop of the boiler To start the boiler, activate the red main switch on the right side of the boiler. After activation, the boiler controller turns on and shows the basic display. To start boiler operation, press the enter button for about 2 seconds. The display shows ON and the boiler switches into the pre-pulse phase with maximum fan power. To switch to automatic operation, the enter button is again pressed for about 2 seconds. Then, the display shows TIMER PROGRAM BOILER. To shut down the boiler, the escape button is pressed for about 2 seconds until the display shows OFF. The boiler switches to the cool-down phase with decreased fan power. To deactivate the boiler, the escape button is again pressed for about 2seconds. By deactivating (after a cooling down period) the main switch, the boiler is powered down completely. 6.4 Setting of the time and date For the setting of the date and time the button is pressed for about 2 seconds. 6.5 Automatic operation To set the hours of operation for the automatic operation, press the button for about 2 seconds. The weekday can be selected by pressing or. To change the operating hours for the selected day, press the enter button. TIMER PROGRAM BOILER MONDAY The display shows two rows each with settable times, the first is the start time, the second is the stop time. In the example below, the boiler starts at 06:00 am and is switched off at 04:00 pm. After a pause the Boiler switches on again at 07:00 pm and stops at 10:00 pm. Then the boiler is deactivated until the next day. The operation times can be set individually for every day of the week. The values can be changed with the buttons and then confirmed with the enter button. After confirming, the display now moves to the next adjustable position. MONDAY The current selection can be changed with the buttons and By pressing the enter button the selection is confirmed. After confirming the display now moves to the next adjustable position. (the seconds cannot be set) Continue as above to make the desired changes. When all positions are set, the user returns to the basic display. To escape the setting without making changes, press the escape button. After all four sets of times are confirmed, the display shows COPY. If this is confirmed with the enter button, the settings are copied to the next day. Pressing the escape button leads to the settings for the next weekday, without copying the changes. NO YES 15

6.6 Operation parameters The following parameters are relevant for boiler operation, pellet combustion, and flue gas temperature. The parameters are set by the technician before commissioning (see page 14). The operation parameters are displayed by pressing the button in the basic display. Press the buttons or to set the value for the selected parameter. Press the escape Press the enter button 1.) Boiler temperature set value: button to go back to the basic display. to confirm the selection. BOILER TEMPERATURE SET POINT BOILER CONTROL 4.) POWER: The centre of the display shows the set power stage. P1: Minimum output operation P2: Intermediate output operation P3: Maximum output operation The bottom row shows the set values. R= The operating duration of the auger P= The Pause duration of the auger V= The Fan-power during heating operation POWER 2.) DHW temperature set value: DHW TEMPERATURE SET POINT 3.) Domestic Hot Water setting HOT WATER HWS PRIORITY HEATING ONLY PARALLEL OPERATION 5.) Switching between summer and winter-mode In summer mode, the boiler only produces domestic hot water. CHANGEOVER SUMMER WINTER SUMMER WINTER Parallel operation = both heating and hot water at the same time to set point. 16

CONTROL PARAMETERS 6.7 Setting parameters Changes of parameters can be carried out by pressing the buttons and together. Below is a list of parameters with the factory settings. The parameters can be changed by pressing or. The setting is confirmed with the enter button then the menu directs the user back to the basic display. 17

CONTROL PARAMETERS Start on page 17 The parameters can be changed by pressing or. The setting is confirmed with the enter button then the menu directs the user back to the basic display. 18

CONTROL PARAMETERS Start on page 17 The parameters can be changed by pressing or. The setting is confirmed with the enter button then the menu directs the user back to the basic display. Temperature difference between heat store & boiler Heat store probe adjustment P2 DHW temperature The asterisk is displayed when DHW is present 19

7 Operational phases OPERATIONAL PHASES 7.1 Ignition phase If the flue gas temperature is above the temperature requiring auto ignition of the pellets, the controller knows that the combustion chamber holds enough ember temperature to successfully continue combustion. In this case the ignition device is not required. The dosage of pellets continues. If the flue gas temperature shows the temperature to be low the controller knows that the combustion chamber has not enough ember temperature to successfully continue combustion. First the fan is switched on to clear the combustion chamber and vents below the ignition device Second the pellet auger pushes enough pellets for light up into the combustion chamber. If a room thermostat or on off control (if used ) switches off, it activates the setting that turns off the boiler and therefore it sends the boiler into a phase of after-run., the boiler will then quickly reach the required temperature and operation will stop. The pump will start if the boiler temperature rises beyond the required temperature and also if the room thermostat demands heat. If the room thermostat /control does not call for heat the pump runs for a period of 5 minutes after the boiler has switched off then the pump stops until the room thermostat/ control calls for heat again. Third the ignition device is switched on The Boiler now enters the warm up phase of operation 7.2 Warm-up phase The ignition device is switched off and the dosage of pellets is reduced. The fan runs with increased speed (according to the setting). in comparison to the combustion phase. The warm-up phase has the purpose to fan the fire and let it spread across the pellets in the combustion chamber. The duration of the warmup phase is fairly short. After this phase, the combustion phase starts. In the case that the flue gas temperature does not rise beyond a pre programmed set temperature the controller recognises that the pellets can not be burning and the boiler stops operation. The display shows FAILED IGNITION. 7.3 Combustion phase During combustion phase, the pellet and air supply are regulated based on the parameter settings. The controller aims for the boiler to increase the temperature up to the Maximum boiler temperature. when this is reached the boiler slowly reduces its output to prevent repeated turning off and on. The boiler shifts to pause mode when the temperature reaches the Maximum boiler temperature. On the top row the display shows Rated temp reached. The boiler re starts operation when the temperature of the boiler flow drops below the set parameter Maximum boiler temperature. The detected flue gas temperature determines if the boiler operation starts with the warm-up phase or the ignition phase as described above 20

8 Maintenance MAINTENANCE 8.1. Intervals of maintenance and cleaning Maintenance work performed periodically is very important for a problem-free operation and the guarantee of a long life of the boiler and other system components. The maintenance period is affected by to the pellet quality and boiler usage. Soot and tar cling to the combustion chamber walls, so their cleaning by hand.is very important Before you start cleaning, turn off the boiler controller and deactivate the main switch. Let the boiler cool to a safe temperature that is not a burn or injury risk Interval Every 3 days Components Clean the heat exchanger and combustion chamber Action Required Move the lever of the heat exchanger cleaning system back and forth 5 to 6 times. Remove the front refractory brick and clean the combustion chamber with a vacuum cleaner. Every month Clean the pellet silo Empty out the pellet silo and remove any wood dust with a vacuum cleaner. Clean the display Carefully clean with slightly damp cloth. Every 6 months Check and clean the flue exhaust passes Check and clean the boiler and flue gas probe The exhaust pipes can be removed and cleaned with the cleaning tool when the system is cooled down. Once a year Clean all part as stated As above & pull out the probes, remove soot and debris. When cleaning the combustion chamber with a vacuum cleaner, the ash inside must be allowed to cool down to prevent accidents. When removing the front brick of the burner, there is a risk of a burn injury Wait for the brick to fully cool down. There is a risk of burns when cleaning the exhaust passes because these surfaces can reach a temperature of up to 200 C during operation. Wait until these parts cool down fully before cleaning. While cleaning, be aware that deadly carbon DANGER monoxide can emit from an opened boiler door or cover. Do not leave the boiler doors open longer than necessary. The ash quantity in the boiler depends on the pellet quality and usage. High quality pellets leave less ash and reduce wood dust in the pellet silo. To prolong the live of the ignition system which ignites the pellets, the ignition system and the air vent must be cleaned regularly. Thoroughly clean the boiler system at the end of the heating season to prolong its live and maintain its efficiency. 21

POSSIBLE FAULTS 9 Possible faults 3) The refractory bricks in the combustion chamber are misaligned System dirty 22

POSSIBLE FAULTS COMMISSIONING Fire Prevention of the Biotec Thermal valve If the boiler is not connected to a suitable flue system (not enough height, wrong diameter of the chimney, dirt or heavily polluted boiler), there is a possibility that fire can spread from the burner into the silo. A part of the combustion air supply is led through the screw channel and thus prevents backfire in the pellet silo. This air current is present at all times during operation but if the flue gas system is badly designed or heavily polluted, the air supply may not be enough to stop the fire spreading up the auger feed. A thermal valve and a probe are mounted on the boiler ex works. If a temperature of 95 C or more is measured by the inbuilt thermal valve (in the auger feed) it is activated and releases water extinguishing the fire The buyer must provide a water supply to the thermal valve (1/2 connection) and comply fully with regulations in force. If the flue gas system is designed incorrectly or heavily polluted or if the boiler is not cleaned regularly or the water supply fails, the manufacturer is not liable for damage caused by such failures. probe Boiler auger showing the thermal valve and probe 10 Commissioning the Biotec Boiler The commissioning of the Biotec boiler may only be carried out by STREBEL or an experienced installer with the approval of Strebel If the start-up is not carried out correctly, the boiler and the system can be damaged or destroyed and be unrepairable. Injury could result from non observation of this manual and general health and safety rules 10.1 Precautions for the first commissioning 1.) Disconnect the boiler from the power supply. 2.) Check if the red main switch is off 9.2 Measures after thermal valve release 1.) Disconnect the boiler from the power supply. 2.) Remove the screw and gear motor. 3.) Remove wet or damp pellets from the silo and the screw channel. 4.) Remove residual water and dry all system parts. NOTE Moisture can cause electrical shorts. 3.) Check that the following parts are installed professionally and working correctly - All mechanical parts of the boiler, - burner and firebricks, - fan, - boiler pump and circuit pump/pumps, - safety valve. 5) Remount the screw and gear motor. 6 )Re fill the silo with dry pellets 7.) Connect to the power supply and test. If wet or damp pellets are not removed completely the screw and motor may jam. The manufacturer rejects responsibility and the warranty expires if material damage occurs because of such failures. 4.) Check all electrical components, connections and devices for correct installation IE gear motor, fan, controller and display. - protect all unused connections, - check earthing - check the power supply. 23

RELOCATION AND BOILER DISPOSAL GUARANTEE 11 Disposal of the boiler 11.1 Removal The boiler removal must be carried out by qualified technicians. Otherwise personal injury or material damage can occur. Guarantee 12.1 Warranty Period The product is guaranteed for two years. 12.2 The guarantee is valid, when - the boiler is installed, mounted and commissioned by STREBEL or a qualified installer, - the boiler is installed complying with national and local regulations - the used pellet quality conforms with the standards stated in this manual. Procedure for relocating the Biotec 1.) Stop the boiler operation. 2.) Wait until the pellets in the combustion chamber are burnt up and the boiler has cooled down. 3.) Disconnect the boiler from power supply. 4.) Disconnect the boiler from the rest of the heating installation and drain the water from the boiler. 5.) Remove the pellet silo. 6.) Remove the boiler shell. 7.) Remove the casing &insulation from the boiler body. Reassemble the Biotec in its new location observing the information with this manual 11.2 Disposal 12.3 The guarantee is invalid, if - the boiler heating system and-flue gas system is designed incorrectly, - the installation and commissioning was not carried out by an approved person, - the repair and maintenance was not carried out by an approved person, The Warranty does not cover: - Damages caused by weather (natural disasters, earthquakes, flood, fire, electric lightening etc.) - damages to electric leads, - use of parts from other manufacturers, - damages caused by faulty system parts such as circuit pumps, expansion vessels etc. The steel parts of the boiler can be delivered to a recycling centre: - Boiler body, - boiler shell, - pellet silo, - screw, - gear motor, - burner. The electrical parts as well as glass parts, mineral wool and plastic parts are separately delivered to a recycling centre. The boiler parts must not be disposed of in a domestic waste bin. 24

TERMINAL CONNECTIONS HEAT STORE PROBE NTC 10K DHW SENSOR NTC 10K AUGER 230V 50HZ 50W FAN 230V 50HZ 41W IGNITION DEVICE 230V 50HZ 400W ROOM STAT OR ON OFF CONTROL BOILER RETURN LIFTING 230V 50HZ <400W DHW PRIMARY PUMP 230V 50HZ <400W HEATING PUMP 230V 50HZ <400W POWER SUPPLY 230 V AC 50HZ 13 AMP 25