HEAT RECOVERY VENTILATOR CONSTRUCTO 1.0 HRV Part no. 41502 (TOP PORTS) Part no. 41500 (SIDE PORTS) 39 to 98 CFM (0.4 in. w.g.) VB0069 AN INGENIOUS AIR EXCHANGE SOLUTION THAT S AS VERSATILE AS IT IS COMPACT! Configured with factory built vertical or horizontal ports, the AVS Constructo 1.0 HRV is the most versatile 98-cfm unit available on the market today. Among its exclusive features, this unit is equipped with integrated balancing and backdraft dampers in its exhaust to outside and fresh air supply ports. For a standard installation, there is no need to balance the unit*, thanks also to its twin high-pressure blowers. Its operation can be interlocked with an existing furnace without adding an extra relay. Also, for more convenience, its latches can be relocated on its front (as shown on unit picture). This compact, lightweight, and powerful unit is the ideal choice for small single-family homes, high rise residential building and other limited space applications. What s more, it is the only air exchanger of its size that can be upgraded from an HRV to an ERV, simply by changing its core. *To avoid balancing, the difference between stale air ducts total length and fresh air ducts total length must not exceed 50 ft. Versatile horizontal or vertical port configuration Removable terminal block to ease auxiliary wall control connections Integrated pressure taps, if balancing required by building code ENERGY STAR qualified REPAIRS AND MAINTENANCE All parts of the AVS Constructo 1.0 HRV that could need maintenance can be removed in less than 5 minutes, allowing direct access for easy repairs. The PSC motors are permanently lubricated. Finally, the removable electrical drawer with pull-out PCB assembly allows easy access for maintenance of major sub-components. WARRANTY The AVS Constructo 1.0 HRV is protected by a 2-year warranty on parts only. The heat recovery core is covered by a limited lifetime warranty, with the original proof of purchase. Available at: Controls This unit is very simple to operate. Once it is installed, press on its push button, located on on the bottom of the unit, to activate it. Press once for low speed, once again for high speed, and once more to stop it. The following main controls are available: - Altitude programmable digital control with SMART mode no. 40440 - Deco-Touch digital control no. 40395 - Constructo no. 40350 - Lite-Touch Constructo no. 40370 - Simple-Touch Constructo no. 40390 The following optional auxiliary controls can also be added: - 20-min. lighted push button no. 40440-60-min. mechanical timer no. 00910 For more details about controls, refer to their specification sheet on venmar.ca. Options Complete line of registers and diffusers Electric duct heater Dual exterior hood kit (including the Tandem transition), part no. 14690 Homeshield Defrosting System The AVS Constructo 1.0 HRV uses a unique defrosting method. No negative pressure is created by air exhausted to the outside, as the air is recirculated into the house, helping to prevent any backdraft. STALE AIR FROM FILTERED AIR TO VF0036 Heat Recovery Core Dimensions: 13 x 19 x 6 7/8 (33 cm x 48.3 cm x 17.3 cm) Exchange surface: 55 ft.2 (5.1 m2) Weight: 3.75 lb. (1.7 kg) Material: Polypropylene Type: Cross flow Warranty: Limited lifetime Requirements and standards OUTSIDE TEMPERATURE DEFROST CYCLE (IN MINUTES) Complies with the UL 1812 requirements regulating the installation of Heat Recovery Ventilators Complies with the CSA C22.2 no. 113 Standard applicable to ventilators Complies with CSA C444 requirements regulating the installation of Heat Recovery Ventilators Technical data was obtained from published results of tests relating to CSA C439 Standards HVI certified and ENERGY STAR qualified oc WARMER THAN -5 of WARMER THAN 23 DEFROST/ OPERATION NO DEFROST -5 TO -27 23 TO -17 8/25-27 & LESS -17 & LESS 10/22
DIMENSIONS: AVS CONSTRUCTO 1.0 HRV (PORTS ON SIDES) ALL PORTS FITS 5 DIAMETER DUCTS 1 4 (102 mm) 27 1/16 (688 mm) 22 9/16 (574 mm) 19 13/16 (503 mm) 6 (152 mm) 13¾ (349 mm) 2 3 4 12 3/16 (310 mm) SPECIFICATIONS 1: FRESH AIR TO PORT 2: EXHAUST AIR FROM PORT VENTILATION PERFORMANCE EXTERNAL STATIC PRESSURE NET AIR FLOW GROSS AIR FLOW EXHAUST PA IN. W.G. L/S CFM M 3 /H L/S CFM M 3 /H L/S CFM M 3 /H 25 0.1 53 111 191 53 112 190 57 120 204 50 0.2 51 107 184 51 108 184 54 114 194 75 0.3 48 101 172 48 102 173 52 110 187 100 0.4 46 98 167 47 99 168 49 105 178 125 0.5 43 91 155 43 92 156 47 100 170 150 0.6 41 88 148 42 88 151 45 96 163 175 0.7 39 82 139 39 83 141 43 91 155 200 0.8 37 79 134 38 80 136 40 85 144 225 0.9 34 73 124 35 74 126 37 79 134 250 1.0 34 71 121 34 72 122 36 76 129 ENERGY PERFORMANCE TEMPERATURE NET AIR FLOW C F L/S CFM M 3 /H POWER CONSUMED WATTS SENSIBLE RECOVERY EFFICIENCY APPARENT LATENT RECOVERY/ SENSIBLE MOISTURE EFFECTIVENESS TRANSFER HEATING 0 32 23 50 85 43 65 74 0.01 0 32 30 64 109 58 62 70 0.01 0 32 39 83 141 70 59 66 0.01-25 -13 23 48 82 56 60 78 0.01-25 -13 30 64 109 64 55 72 0 COOLING VK0055A TOTAL RECOVERY EFFICIENCY 35 95 - - - - NOT TESTED 2 (51 mm) 3: FRESH AIR FROM OUTSIDE PORT 4: EXHAUST AIR TO OUTSIDE PORT AVS CONSTRUCTO 1.0 HRV (PORTS ON TOP) 1913 16 (503 mm) 16¼ (413 mm) NOTE: All specifications are subject to change without notice. Model: AVS Constructo 1.0 HRV Core filters: 30 ppi washable foam Speed control on unit: Low & high speeds. Part number top ports: 41502 10.5 x 6.75 x 0.5 (26.7 cm x 17.2 cm x 1.3 cm) Other modes available with main and Part number side ports: 41500 Housing: Pre-painted steel optional wall controls Total assembled weight (including Insulation: Expanded polystyrene Heat recovery core: polypropylene core): 42 lb. (19 kg) Mounting: Suspension by chains - Heat exchange surface area: 55 ft. 2 (5.1 m 2 ) and springs - Type/Material: Crossflow/Polypropylene Oval shaped ports; fit 5 diameter ducts Supply and exhaust blower motor: 2 motors Unit electrical characteristics: Drain: 1/2 (1.2 cm) fittings with - Protection type: Thermally protected Volts Frequency Ampere Watts 10 ft. (3 m) PVC drain hose - Insulation class: B 120 60 Hz 0.85 100 VK0056A ALL PORTS FITS 5 DIAMETER DUCTS 1 2 3 22 9 16 (574 mm) 23¾ (603 mm) 4 1: FRESH AIR TO PORT 2: EXHAUST AIR FROM PORT 3: FRESH AIR FROM OUTSIDE PORT 4: EXHAUST AIR TO OUTSIDE PORT 4 (102 mm) 6 (152 mm) 12 3 16 (310 mm) 2½ (64 mm) Project: Location: Part no.: Qty.: Submitted by: Date: REMARKS Residential Products Group, 550 Lemire Blvd., Drummondville, Qc, Canada J2C 7W9 - Tel.: 1-800-567-3855 Fax: 1-800-567-1715 www.venmar.ca 13/11 PRODUCT SHEET NO. 91047
HEAT RECOVERY VENTILATOR HRV CONSTRUCTO 1.5ES Part no. 46110 CANADA Part no. 1601702 U.S.A. 66 to 150 CFM (0.4 in. w.g.) VB0166 CONSTRUCTO SERIES: PERFECT FOR NEW RESIDENTIAL CONSTRUCTION Contractors and builders need cost-effective, reliable and code-compliant mechanical ventilation systems for new home construction. The Venmar AVS Constructo Series offers superior value at an entry-level price. The Constructo 1.5ES represents over 15 years of continuous improvement to deliver contractors the durability and reliability they have come to expect from Venmar. Key features: Maintenance free, totally enclosed, sealed bearings motor Pressure taps, balancing dampers and straps for insulated ducts for quick, effective installation Integrated snap-in drain system installs in seconds with no additional parts ENERGY STAR qualified Compatible with the Deco-Touch digital wall control REPAIRS AND MAINTENANCE All parts of the HRV Constructo 1.5ES that could need maintenance can be removed in less than 5 minutes, allowing direct access for easy repairs. The motor is permanently lubricated. WARRANTY The HRV Constructo 1.5ES is protected by a 5-year warranty on parts. The heat recovery core is covered by a limited lifetime warranty, with the original proof of purchase. Available at: Controls This unit is very simple to operate: press on its push button, located on the electrical compartment, to activate it. Press once for low speed, once again for high speed, and once more to stop it. The following main controls are available: - Deco-Touch digital control* no. 40395 - Lite-Touch Constructo no. 40370 - Constructo no. 40350 * Recirculation mode not available. Up to 5 of the following optional auxiliary controls can also be added: - Dehumidistat no. 11297-20-min. lighted push-button no. 12030 For more details about controls, refer to their specification sheet on venmar.ca. Option Complete line of registers and diffusers Defrosting System The HRV Constructo 1.5ES uses an efficient defrosting method. No negative pressure is created by air exhausted to the outside, as the air is recirculated into the house, helping to prevent any backdraft. OUTSIDE TEMPERATURE DEFROST CYCLE ºC ºF DEFROSTING MIN./OPERATING MIN. WARMER THAN -5 WARMER THAN 23 NO DEFROST -5 TO -15 23 TO 5 7/50-15 TO -27 5 TO -17 7/25-27 & LESS -17 & LESS 10/20 VF0053 STALE AIR FROM FILTERED AIR TO Heat Recovery Core Dimensions: 12 x 14 x 15.5 (30.5 cm x 35.5 cm x 39.4 cm) Exchange surface: 102 ft² (9.54 m²) Weight: 6.2 lb (2.8 kg) Material: Polypropylene Type: Crossflow core Warranty: Limited Lifetime Requirements and Standards Complies with the UL 1812 requirements regulating the Complies with the CSA C22.2 no. 113 Standard applicable to ventilators Complies with CSA F326 requirements regulating the Technical data was obtained from published results of tests relating to CSA C439 Standards HVI certified and ENERGY STAR qualified
Dimensions: HRV Constructo 1.5ES Hooks Location for Hanging Chains Motorized Damper 35 (891 mm) 30¼ (768 mm) 17¼ (438 mm) Terminal Block Location Heat Recovery Core 17 (432 mm) Door VK0077A Power Cord 36 (914 mm) Blower Assembly 6 (152 mm) Ventilation Performance EXT. STATIC PRESSURE NET AIR FLOW GROSS AIR FLOW EXHAUST PA IN. W.G. L/S CFM M³/H L/S CFM M³/H L/S CFM M³/H 25 0.1 85 180 306 86 182 309 92 194 330 50 0.2 82 174 296 82 175 297 86 182 309 75 0.3 77 163 277 77 164 279 81 171 291 100 0.4 71 150 255 71 151 257 71 151 257 125 0.5 67 141 240 67 142 241 57 120 204 150 0.6 60 128 217 61 130 221 40 85 144 175 0.7 51 108 183 52 110 187 27 57 97 EXTERNAL STATIC PRESSURE IN. W.G. (PA = N X248.8) 0.8 0.6 0.4 0.2 (L/S) EXHAUST (L/S) 0 VG0089A 0 25 50 75 100 125 150 175 200 CFM (L/S = CFM X 0.4719) (M³/H = L/S X3.6) Energy Performance NET AIR FLOW POWER SENSIBLE APPARENT LATENT RECOVERY TEMPERATURE CONSUMED RECOVERY SENSIBLE MOISTURE ºC ºF L/S CFM M³/H WATTS EFFICIENCY EFFECTIVENESS TRANSFER HEATING 0 32 31 66 112 67 67 79-0.01 0 32 40 86 146 74 65 75-0.01 0 32 54 115 195 90 61 70-0.01-25 -13 38 81 138 87 60 76 0.02 EFFICIENCY VG0090 100 90 80 70 60 50 APPARENT (%) NET (%) 40 0 25 50 75 100 AIR FLOW - L/S (0.47 L/S = 1 CFM) NOTE: All specifications are subject to change without notice. Specifications and Ratings Model: HRV Constructo 1.5ES Part Number Canada: 46110 Part Number U.S.A.: 1601702 Total Assembled Weight (including polypropylene core): 65 lb (29.5 kg) Drains:1/2 (1.2 cm) fittings with 10 ft (3 m) PVC drain Filters: 15 ppi washable reticulated foam 15.375 x 7.125 x 0.75 (39 cm x 18 cm x 1.9 cm) 6 Round Ports Housing: Pre-painted steel Insulation: Expanded polystyrene Mounting: Suspension by chains and springs Supply & Exhaust Blower Motor: 1 PSC motor - Protection type: Thermally protected - Insulation class: B Speed Control on unit: Low & High speed. Other modes available with optional mainl wall controls. Heat Recovery Core: - Heat Exchange Surface Area: 102 ft² (9.54 m²) - Type/Material: Crossflow/Polypropylene Unit Electrical Characteristics: Volts Frequency Amps Watts 120 60 Hz 1.5 160 PROJECT: LOCATION: MODEL NO.: QTY.: SUBMITTED BY: DATE: REMARKS Residential Product Group, 550 Lemire Blvd., Drummondville, QC, Canada J2C 7W9 - Tel.: 1-800-567-3855 Fax: 1-800-567-1715 www.venmar.ca HRVConstructo1.5ESd120518
HEAT RECOVERY VENTILATOR HRV CONSTRUCTO 2.0ES Part no. 47110 82 to 192 CFM (0.4 in. w.g.) VB0167 CONSTRUCTO SERIES: PERFECT FOR NEW RESIDENTIAL CONSTRUCTIONS Contractors and builders need cost-effective, reliable and code-compliant mechanical ventilation systems for new home constructions. The Venmar AVS Constructo Series offers superior value at an entry-level price. The Constructo 2.0ES represents over 15 years of continuous improvement to deliver contractors the durability and reliability they have come to expect from Venmar. Key features: Maintenance free, totally enclosed, sealed bearings motor Pressure taps, balancing dampers and straps for insulated ducts for quick, effective installation Integrated snap-in drain system installs in seconds with no additional parts ENERGY STAR qualified Compatible with the Deco-Touch digital wall control REPAIRS AND MAINTENANCE All parts of the HRV Constructo 2.0ES that could need maintenance can be removed in less than 5 minutes, allowing direct access for easy repairs. The motor is permanently lubricated. WARRANTY The HRV Constructo 2.0ES is protected by a 5-year warranty on parts. The heat recovery core is covered by a limited lifetime warranty, with the original proof of purchase. Available at: Controls This unit is very simple to operate: press on its push button, located on the electrical compartment, to activate it. Press once for low speed, once again for high speed, and once more to stop it. The following main controls are available: - Deco-Touch digital control* no. 40395 - Lite-Touch Constructo no. 40370 - Constructo no. 40350 * Recirculation mode not available. Up to 5 of the following optional auxiliary controls can also be added: - Dehumidistat no. 11297-20-min. lighted push-button no. 12030 For more details about controls, refer to their specification sheet on venmar.ca. Option Complete line of registers and diffusers Defrosting System The HRV Constructo 2.0ES uses an efficient defrosting method. No negative pressure is created by air exhausted to the outside, as the air is recirculated into the house, helping to prevent any backdraft. OUTSIDE TEMPERATURE DEFROST CYCLE ºC ºF DEFROSTING MIN./OPERATING MIN. WARMER THAN -5 WARMER THAN 23 NO DEFROST -5 TO -15 23 TO 5 6/50-15 TO -27 5 TO -17 6/25-27 & LESS -17 & LESS 10/20 VF0053 STALE AIR FROM FILTERED AIR TO Heat Recovery Core Dimensions: 12 x 14 x 15.5 (30.5 cm x 35.5 cm x 39.4 cm) Exchange surface: 102 ft² (9.54 m²) Weight: 6.2 lb (2.8 kg) Material: Polypropylene Type: Crossflow core Warranty: Limited Lifetime Requirements and Standards Complies with the UL 1812 requirements regulating the Complies with the CSA C22.2 no. 113 Standard applicable to ventilators Complies with CSA F326 requirements regulating the Technical data was obtained from published results of tests relating to CSA C439 Standards HVI certified and ENERGY STAR qualified
Dimensions: HRV Constructo 2.0ES Hooks Location for Hanging Chains Motorized Damper 35 (891 mm) 30¼ (768 mm) 17¼ (438 mm) Terminal Block Location Heat Recovery Core 17 (432 mm) Door VK0077A Power Cord 36 (914 mm) Blower Assembly 6 (152 mm) Ventilation Performance EXT. STATIC PRESSURE NET AIR FLOW GROSS AIR FLOW EXHAUST PA IN. W.G. L/S CFM M³/H L/S CFM M³/H L/S CFM M³/H 25 0.1 106 225 382 107 227 386 118 249 423 50 0.2 102 215 365 102 216 367 115 243 413 75 0.3 96 204 347 97 205 348 111 235 399 100 0.4 90 192 326 91 193 328 107 226 384 125 0.5 83 177 301 84 179 304 100 211 358 150 0.6 76 161 274 76 162 275 89 189 321 175 0.7 67 142 241 67 143 243 75 159 270 EXTERNAL STATIC PRESSURE IN. W.G. (PA = N X248.8) 0.8 0.6 0.4 0.2 (L/S) EXHAUST (L/S) 0 0 25 50 75 100 125 150 175 200 225 250 275 VG0091A CFM (L/S = CFM X 0.4719) (M³/H = L/S X3.6) Energy Performance POWER SENSIBLE APPARENT LATENT/RECOVERY NET AIR FLOW TEMPERATURE CONSUMED RECOVERY SENSIBLE MOISTURE ºC ºF L/S CFM M³/H WATTS EFFICIENCY EFFECTIVENESS TRANSFER HEATING 0 32 39 82 139 71 65 75 0.01 0 32 61 130 221 129 60 69 0.01-25 -13 40 84 143 114 60 76 0.03 EFFICIENCY 100 90 80 70 60 50 40 0 25 50 75 100 VG0092 APPARENT (%) NET (%) AIR FLOW - L/S (0.47 L/S = 1 CFM) NOTE: All specifications are subject to change without notice. Specifications and Ratings Model: HRV Constructo 2.0ES Part Number: 47110 Total Assembled Weight (including polypropylene core): 65 lb (29.5 kg) 6 Round Ports Drains:1/2 (1.2 cm) fittings with 10 ft (3 m) PVC drain Filters: 15 ppi washable reticulated foam 15.375 x 7.125 x 0.75 (39 cm x 18 cm x 1.9 cm) Housing: Pre-painted steel Insulation: Expanded polystyrene Mounting: Suspension by chains and springs Supply & Exhaust Blower Motor: 1 PSC motor - Protection type: Thermally protected - Insulation class: B Speed Control on unit: Low & High speed. Other modes available with optional main wall controls. Heat Recovery Core: - Heat Exchange Surface Area: 102 ft² (9.54 m²) - Type/Material: Crossflow/Polypropylene Unit Electrical Characteristics: Volts Frequency Amps Watts 120 60 Hz 2.1 195 PROJECT: LOCATION: MODEL NO.: QTY.: SUBMITTED BY: DATE: REMARKS Residential Product Group, 550 Lemire Blvd., Drummondville, QC, Canada J2C 7W9 - Tel.: 1-800-567-3855 Fax: 1-800-567-1715 www.venmar.ca HRVConstructo2.0ESd120518