堤維西交通工業股份有限公司 T.Y.C. BROTHER IND. CO., LTD. TEL:+886-6-2658781 ext. 413 FAX:+886-6-2912800 APPLICATION FOR APPROVAL OF A TYPE OF FRONT FOG LAMP ACCORDING TO ECE REGULATION NO. 19-02 SERIES OF AMENDMENTS 1. Trade name or mark of the device : TYC 2. Manufacturer s name of the device : 3. Manufacturer s name and address : No. 72-2, SHIN-LEH RD., AN-PING INDUSTRIAL DISTRICT, TAINAN, TAIWAN, R.O.C. 4. If applicable, name and address of manufacturer s representative 5. Category as described by the relevant markings : Not applicable : 02 B PL 6. Submitted for approval on(date) : February 23, 2012 Ms. Agnes Su R & D DEPARTMENT We herewith confirm that above mentioned application has not been submitted to any other EC/ECE-Member State nor has Member State granted a corresponding type approval. This application is accompanied by: The test report
Vehicle Technology Division THE NETHERLANDS (N E D E R L A N D) COMMUNICATION Concerning (1) : - approval granted - approval extended - approval refused - approval withdrawn - production definitely discontinued of a type of motor vehicle front fog lamp pursuant to Regulation number 19. Approval number: E4-19R-02190043 Extension number: 00 Approval mark: 190043 02B PL Indication of the approval mark for the device on both sides 1. Trade name or mark of the device : TYC () 2. Front fog lamp using a filament lamp category : H11 3. Manufacturer s name and address : No. 72-2, Shin-Leh Rd., An-Ping Industrial District, Tainan, Taiwan, R.O.C. 4. If applicable, name and address of manufacturer s representative : Not applicable 5. Submitted for approval on : February 23 to April 6, 2012 P.O. Box 777 Tel. + 31 (0)79 345 81 43 Vehicle Approval and Information 2700 AT Zoetermeer Fax + 31 (0)79 345 80 43 The Netherlands www.rdw.nl Lamps-front-fog R19-02 v4.01 Page 1 of 2
Approval number: E4-19R-02190043 Extension number: 00 6. Technical service responsible for conducting approval tests : TÜV Rheinland Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit Postfach 91 09 51 D-51101 Köln / Germany 7. Date of report issued by that service : May 3, 2012 8. Number of test report issued by that service : 84-R19-00164/12 9. Brief description: Colour of light emitted : White/selective yellow (1) Category as described by the relevant marking Number and category of filament lamp(s) Rated voltage (brackets) : B, B/, BPL, B/PL (1) : One H11 : 12V 10. Position of approval mark : On the outer lens of the lamp 11. Reason(s) for extension (if applicable) : Not applicable 12. Approval : Granted/extended/refused/withdrawn (1) 13. Place : Zoetermeer 14. Date : 15. Signature : 16. The list of documents deposited with the Administrative Service which has granted approval is annexed to this communication and may be obtained on request. (1) Strike out what does not apply. Lamps-front-fog R19-02 v4.01 Page 2 of 2
T E S T R E P O R T according to ECE-Regulation Uniform provisions concerning the approval of power-driven vehicle front fog lamps No.: ECE-R19 including all amendments until No.: 02 series of amendments, suppl. 14 Previously granted ECE - approval : -- Structure of report: 0. General information 1. Test object(s) and general test information 2. Test minutes 3. Remark concerning tested object(s) 4. Appendices 5. Statement of conformity The Test Report shall be reproduced and published in full by the client only. It shall however be reproduced partially with the written permission of the Testing Laboratory only. TÜV Rheinland Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit 28-164e12.rdw Page 1 of 10
0. General information 0.1. Trade mark or trade name of the lamp 0.2. Manufacturer s name for the type of the lamp 0.3. Name and address of the manufacturer 0.4. Name and address of the manufacturer s authorised representative 0.5. No. of information document date of issue date of last amendment : TYC : : No. 72-2, Shin-Leh Rd., An-Ping Industrial District, Tainan, Taiwan, R.O.C. : Not applicable : : : -A1 February 23, 2012 -- TÜV Rheinland Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit 28-164e12.rdw Page 2 of 10
1. Test object(s) and general test information 1.1. Test object(s) - Identification no. : Not applicable - Model : - Remark : Front fog lamp, incorporating a lens made of plastic 1.2. General test information 1.2.1 Order issued by (if different from manufacturer) : -- 1.2.2 Test object received on : -- 1.2.3 Test date : February 23 to April 6, 2012 1.2.4 Test site : Tainan / Taiwan 1.2.5 Remark : The results of the test refer exclusively to the objects mentioned under point 1.1. of this report. TÜV Rheinland Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit 28-164e12.rdw Page 3 of 10
2. Test minutes 2.1. Test facilities : The measurement equipment used was in compliance with the test requirements. 2.2. Test results : The lamp type has been tested according to the amendments mentioned in appendix 0. 2.2.1 Temperature : 25 C 2.2.2 Markings : The trade mark is marked clearly legible and indelible on the outer lens of the lamp. Space for the approval mark and for the additional symbols is provided on the outer lens of the lamp. 2.3. General specifications : The fog lamp is designed and made that, under normal use, their satisfactory operation is ensured and they retain the required characteristics. The filament lamp can be fixed in no position but the correct one. The construction of the fog lamp complies with the requirements as described in paragraph 5.2. The filament lamp holder conforms to the characteristics stated in the IEC publication 60061. 2.4. Photometric tests : The light emitted was obtained by means of the standard lamp(s) as specified in the information document, producing the required luminous flux. The fog lamp was adjusted so that the cut-off on the screen appeared 50 cm below the line hh. The fog lamp beam produces a "cut-off" line symmetrically to the line VV. No variations in illumination detrimental to satisfactory visibility in both of the zones B and C have been observed. TÜV Rheinland Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit 28-164e12.rdw Page 4 of 10
Results of photometric tests of the front fog lamp illumination produced on the screen in lux sample no.1 (left side) sample no. 2 (right side) illumination required min max min max Zone A 0.25 0.32 0.22 0.33 0.15 and 1.0 Zone B -- 0.32 -- 0.33 1.0 Zone C -- 0.30 -- 0.38 0.5 Zone D 4.50 -- 4.36 -- 1.5 Zone E 0.60 -- 1.41 -- 0.5 illumination in any direction of more than 15 above horizontal hh in cd sample no. 1 sample no. 2 min max min max illumination required Zone C -- 50.0 -- 62.5 200 TÜV Rheinland Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit 28-164e12.rdw Page 5 of 10
2.5. Stability of photometric performance of front fog lamps in operation 2.5.1 Stability of photometric performance 2.5.1.1 Clean Fog lamp : The lamp was operated for 12 hours according to the applicable cycle as described in paragraph 1.1.1. of Annex 4 of the Regulation. The visual inspection after this test did not show any distortion, deformation, cracking or change in colour of the fog lamp lens. Photometric test results (in lux) points on screen initial end of test difference in % Emax in Zone D allowable difference in % 4.23 4.2-0.71 10 H-V 0.32 0.31-3.13 10 2.5.1.2 Dirty Fog lamp : After preparation as prescribed in paragraph 1.2.1. of Annex 4 of the Regulation, and confirmation that the illumination values have dropped to 15% to 20 % of the prior values, the fog lamp was operated for 1 hour according to the applicable cycle as described in paragraph 1.1.1. of Annex 4. The visual inspection after this test did not show any distortion, deformation, cracking or change in colour of the fog lamp lens. Photometric test results (in lux) points on screen initial end of test difference in % Emax in Zone D allowable difference in % 4.23 4.12-2.60 10 H-V 0.32 0.3-6.25 10 TÜV Rheinland Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit 28-164e12.rdw Page 6 of 10
2.5.2 Change in vertical position of the cut-off line under the influence of heat : Test result in accordance with paragraph 2 of Annex 4 of the Regulation in milliradians (mrad) (maximum deviation measurement): points on screen sample no. 1 sample no. 2 r 3 0.35 -- maximum permissible r 60 0.70 -- r 1 = r 3 - r 60 0.35 -- 2.0 2.6. Coloured lenses, filters and filament lamps The colouring beam is obtained through : Not applicable The CIE trichromatic co-ordinates of the light emitted by the fog lamp are within the limits in the paragraph 7. of the Regulation. 2.7. Explanatory note : This report describes the examination of the fog lamp as a part of a lamp device. For the examination of the other lamp of the device, refer to the following report: Type of lamp 2.8. Variants and components : Not applicable -- -- Test Report No. TÜV Rheinland Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit 28-164e12.rdw Page 7 of 10
2.9. Lamps incorporating lenses of : The lamp manufacturer proved that the product had plastic material already passed the tests prescribed in paragraphs 2.1.-2.5. of Annex 5 to this ECE-Regulation, or the equivalent tests pursuant to another Regulation. With references to: Approval No. : E4-19R-0219889 Test report No. : 84-R19-01383/10 Those tests need not to be repeated. Only the tests prescribed in appendix 1, table B were conducted. 2.9.1 Tests according to paragraph 2.6 of : The lens of sample No. 1 was conditioned in accordance the complete lamp incorporating a with the test described in paragraph 2.4.1. lens of plastic material photometric test results after conditioning (in lux) point illumination measured illumination required E max in Zone A 0.30 1.3 E max in Zone B 0.35 1.3 Test of adherence of coatings : The sample No. 2 complies with the requirements mentioned paragraph 2.5. TÜV Rheinland Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit 28-164e12.rdw Page 8 of 10
3. Remark concerning tested object(s) All versions of the lamp type as stated in the information document are covered with the tested lamp version(s) and test object(s) respectively. 4. Appendices 0 List of modifications 1 Information folder No. (excluding drawings) : -A1 (1 page) 5. Statement of conformity The above mentioned information folder and the type described in that comply with the requirements mentioned on page 1. Cologne, May 3, 2012 KWU/JYW B.S.M.E. J. Wu TÜV Rheinland Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit 28-164e12.rdw Page 9 of 10
List of modifications Appendix 0 Correction of : -- Modification of : -- Addition of : -- Deletion of : -- TÜV Rheinland Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit 28-164e12.rdw Page 10 of 10
Information Folder No.: -A1 Page 1 / 1 Application Type: First Application Date: February 23, 2012 Application regulation: ECE-R19-02 (class B) 1. Light Sources Function Light Color Rated Voltage Rated Wattage Category (ECE-R37) Frong fog lamp White 12V 55W H11 2. Construction and Material Construction Material Remark Outer lens PC (Panlite / L-1225Z 100) Colourless (coating: GE Silicones / UVHC3000) Reflector Plastic Aluminum vacuum coated Housing Frame Plastic Plastic 3. The locations of the trade mark(s), the lamp designation mark(s) and the approval mark(s) are indicated in the following drawing(s) attached: 19B015-1002-0000-01 4. The front fog lamp is intended as replacement for fitting to the vehicle (Brand: BMW/ Model: 1 Series / Year: 2007-2011) 5. Name and address of manufacturer: No. 72-2, SHIN-LEH RD., AN-PING INDUSTRIAL DISTRICT, TAINAN, TAIWAN, R.O.C. 6. Name and address of representative of manufacturer: Not applicable 7. Remarks Date: February 23, 2012 Place: Tainan, Taiwan, R.O.C. Person in charge: Ms. Agnes Su