95%/93% AFUE HEATING INPUT: 46,000 5,000 BTU/H Standard Features / MULTI-POSITION, DUAL$AVER ONVERTIBLE, MULTI-SPEED GAS FURNAE The Goodman / 95%/93% AFUE Dual$aver onvertible, Multi-Speed, Multi-Position furnaces feature a patented aluminized-steel tubular heat exchanger and durable Silicon Nitride Hot Surface Ignition system. Patented TuffTube dual-diameter tubular heat exchanger with lifetime limited warranty plus 0-year limited furnace replacement warranty Two-stage gas valve with revolutionary new convertible technology that allows installer to activate the two-stage valve with the flip of a dipswitch Silicon Nitride igniter with patented adaptive learning control for maximum igniter life Furnace control board with self-diagnostics, color-coded low-voltage terminals, and provisions for electronic air cleaner and 4-volt humidifiers ontrol board stores the last five diagnostic codes in memory; simple push-button activation outputs the fault history to a flashing red LED Low constant fan allows homeowner to activate the low heat speed to efficiently circulate air throughout the home. Self-adjusting feature automatically adjusts to high or low stage based on outside temperature without an outdoor temperature sensor Dual-certified for sealed combustion direct vent (-pipe) or non-direct vent (-pipe) applications Easy-to-install top venting is standard; alternate flue/vent located on the right () All models comply with alifornia NOx emissions standards abinet Features Fully insulated, heavy-gauge steel cabinet with durable baked-enamel finish Foil-faced insulation lines the heat exchanger Designed for multi-position installation : upflow, horizontal left or right; : downflow, horizontal left or right Airtight solid bottom for side-return applications and easycut tabs for effortless removal in bottom air inlet applications onvenient left or right connection for gas & electric service oil and furnace fit flush for most installations ontents Nomenclature... Product Specifications...3 Dimensions...4 Blower Performance Specifications... 7 Wiring Diagrams...3 Accessories...5 For full warranty details, visit www.goodmanmfg.com. SS- www.goodmanmfg.com /08 Supersedes 6/08
NOMENLATURE G M H 3 95 70 4,5 6,7,8 4 9 B X A 0 Brand Revisions G Goodman Brand A Initial Release or Distinctions B st Revision nd Revision Airflow Direction Downflow/Horizontal D Dedicated Downflow NOx H High Airflow N Natural Gas K Dedicated Upflow X Low NOx M Upflow/Horizontal abinet Width Description A 4 V Two-Stage/Variable-speed B 7½ H Two-Stage/Multi-speed S Single-Stage/Multi-speed D 4½ E Two-Stage/X-3 Motor AFUE Maximum FM @ 0.5 ESP 95 95% 3,00 9 90%+ 4,600 8 80% 5,000 MBTU/h 045: 45,000 5: 5,000 070: 70,000 40: 40,000 090: 90,000 www.goodmanmfg.com SS-
SPEIFIATIONS F Heating apacity 0453BXA 0703BXA 0704XA 0904XA 0905DXA 55DXA Input¹ 46,000 69,000 69,000 9,000 9,000 5,000 Natural Gas Output¹ 44,600 66,400 66,400 89,000 88,400 0,500 LP Gas Output¹ 39,330 58,995 58,995 78,660 78,660 98,35 AFUE² 95 95 95 95 95 95 Available A @ 0.5 ESP 3 3 4 4 5 5 Temperature Rise Range ( F) 35-65 35-65 35-65 35-65 35-65 35-65 irculator Blower Size (D x W) 0 x 8 0 x 8 0 x 0 0 x 0 x 0 x 0 Horsepower @ 075 RPM ⅓ ⅓ ½ ½ ¾ ¾ Speed 4 4 4 4 4 4 Vent Diameter³ 3 3 No. of Burners 3 3 4 4 5 Filter Size (in²) Permanent 4 90 88 385 385 480 486 Disposable 580 580 770 770 960 960 Electrical Data Min. ircuit Ampacity 5 9.4 9.4 3.8 3.8 3. 3. Max. Overcurrent Device (amps) 6 5 5 5 5 5 5 Ship Weight (lbs) 3 35 36 58 7 75 3 4 5 6 Natural Gas BTU/h. For altitudes above,000, reduce input rating 4% for each,000 above sea level. Low-fire rate is 75% of high-fire rate DOE AFUE based upon Isolated ombustion System (IS) Vent and combustion air diameters may vary depending upon vent length. Refer to the latest editions of the National Fuel Gas ode NFPA 54/ANSI Z3. (in the USA) and the anada National Standard of anada, AN/SA B49. and AN/SA B4. (in anada). Permanent air filter size is based on 600 FPM velocity. heck with filter manufacturer for specific details. Minimum ircuit Ampacity = (.5 x irculator Blower Amps) + ID Blower amps. Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. Maximum Overcurrent Protection Device refers to maximum recommended fuse or circuit breaker size. Must use fuses or HAR-type circuit breakers of the same size as noted. Notes: All furnaces are manufactured for use on 5 VA, 60 Hz, single-phase electrical supply. Gas Service onnection ½ FPT Important: Size fuses and wires properly and make electrical connections in accordance with the National Electrical ode and/or all existing local codes. SS- www.goodmanmfg.com 3
SPEIFIATIONS F Heating apacity 0453BXA 0703BXA 0704XA 0904XA 0905DXA 55DXA Natural Gas Input¹ 46,000 69,000 69,000 9,000 9,000 5,000 Natural Gas Output¹ 4,800 64,400 64,400 86,000 86,000 06,500 LP Gas Output¹ 38,50 57,753 57,753 77,004 77,004 96,55 AFUE² 93 93 93 93 93.0 93 Available A @ 0.5 ESP 3 3 4 4 5 5 Temperature Rise Range ( F) 35-65 35-65 35-65 40-70 35-65 40-70 irculator Blower Size (D x W) 0 x 8 0 x 8 0 x 0 0 x 0 x 0 x 0 Horsepower @ 075 RPM ⅓ ⅓ ½ ½ ¾ ¾ Speed 4 4 4 4 4 4 Vent Diameter³ No. of Burners 3 3 4 4 5 Filter Size (in) Permanent 4 88 8 60 376 376 470 Disposable 576 564 564 75 75 940 Electrical Data Min. ircuit Ampacity 5 9.4 9.4 3.8 3.8. 3. Max. Overcurrent Device (amps) 6 5 5 5 5 5 5 Ship Weight (lbs) 3 35 35 56 73 75 3 4 5 6 Natural Gas BTU/h. For altitudes above,000, reduce input rating 4% for each,000 above sea level. Low-fire rate is 75% of high-fire rate DOE AFUE based upon Isolated ombustion System (IS) Vent and combustion air diameters may vary depending upon vent length. Refer to the latest editions of the National Fuel Gas ode NFPA 54/ANSI Z3. (in the USA) and the anada National Standard of anada, AN/SA B49. and AN/SA B4. (in anada). Permanent air filter size is based on 600 FPM velocity. heck with filter manufacturer for specific details. Minimum ircuit Ampacity = (.5 x irculator Blower Amps) + ID Blower amps. Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. Maximum Overcurrent Protection Device refers to maximum recommended fuse or circuit breaker size. Must use fuses or HAR-type circuit breakers of the same size as noted. Notes: All furnaces are manufactured for use on 5 VA, 60 Hz, single-phase electrical supply. Gas Service onnection ½ FPT Important: Size fuses and wires properly and make electrical connections in accordance with the National Electrical ode and/or all existing local codes. 4 www.goodmanmfg.com SS-
DIMENSIONS AIR DISHARGE AIR DISHARGE AIR INTAKE PIPE " PV / RIGHT SIDE DRAIN LINE HOLES 5/8 UNFOLDED FLANGES UNFOLDED FLANGES FOLDED FLANGES FOLDED FLANGES RIGHT SIDE VIEW Model A B D E 0453BXA 7½ 6 3⅛ ⅛ 3⅝ 0703BXA 7½ 6 3⅛ ⅛ 3⅝ 0704XA 9½ 6⅛ 6 7½ 0904XA 9½ 6⅛ 6 7½ 0905DXA 4½ 3 0⅝ 9⅜ 0⅞ 55DXA 4½ 3 0⅝ 9⅜ 0⅞ Notes: Installer must supply one or two PV pipes: one for combustion air (optional) and one for the fl ue outlet (required). Vent pipe must be either or 3 in diameter, depending upon furnace input, number of elbows, length of run, and installation ( or pipes). The optional combustion air pipe is dependent on installation/code requirements and must be or 3 diameter PV. Line voltage wiring can enter through the right or left side of furnace. Low-voltage wiring can enter through the right or left side of furnace. onversion kits for high-altitude natural gas operation are available. ontact your Goodman distributor or dealer for details. Installer must supply the following gas line fi ttings, according to which entrance is used: Left: One 90º street elbow; one ½ pipe nipple; one 90º elbow; straight pipe; one ground joint union Right: Straight pipe to reach gas valve Installations using a bottom return: Failure to unfold duct fl anges will reduce airfl ow area by approximately 8%. This could result in performance and noise issues. MINIMUM LEARANES TO OMBUSTIBLE MATERIALS Position Sides Rear Front Bottom Flue Top Upfl ow 0 0 0 Horizontal 6 0 0 4 = If placed on combustible fl oor, the fl oor MUST be wood ONLY. For servicing or cleaning, a 4 front clearance is recommended. Unit connections (electrical, fl ue, and drain) may necessitate greater clearances than the minimum clearances listed above. In all cases, accessibility clearance must take precedence over clearances from the enclosure where accessibility clearances are greater. Approved for line contact in the horizontal position SS- www.goodmanmfg.com 5
DIMENSIONS AIR Model A B D E 0453BXA 7½ 6 ⅜ 4½ 6 0703BXA 7½ 6 ⅜ 4½ 6 0704XA 9½ 6⅜ 8 9½ 0904XA 9½ 6⅜ 8 9½ 0905DXA 4½ 3 0⅜ ½ 3 55DXA 4½ 3 0⅜ ½ 3 Notes: Installer must supply one or two PV pipes: one for combustion air (optional) and one for the fl ue outlet (required). Vent pipe must be either or 3 in diameter, depending upon furnace input, number of elbows, length of run, and installation ( or pipes). The optional combustion air pipe is dependent on installation/code requirements and must be or 3 diameter PV. Line voltage wiring can enter through the right or left side of furnace. Low-voltage wiring can enter through the right or left side of furnace. onversion kits for high-altitude natural gas operation are available. ontact your Goodman distributor or dealer for details. Installer must supply the following gas line fi ttings, according to which entrance is used: Left: One 90º street elbow; one ½ pipe nipple; one 90º elbow; straight pipe; one ground joint union Right: Straight pipe to reach gas valve Installations using a bottom return: Failure to unfold duct fl anges will reduce airfl ow area by approximately 8%. This could result in performance and noise issues. MINIMUM LEARANES TO OMBUSTIBLE MATERIALS Position Sides Rear Front Bottom Flue Top Downflow 0 0 N 0 Horizontal 6 0 0 4 = ombustible: If placed on combustible fl oor, the fl oor MUST be wood ONLY. N = Non-ombustible: A combustible fl oor sub-base must be used for installation on combustible fl ooring Notes: For servicing or cleaning, a 4 front clearance is recommended. Unit connections (electrical, fl ue and drain) may necessitate greater clearances than the minimum clearances listed below. In all cases, accessibility clearance must take precedence over clearances from the enclosure where accessibility clearances are greater. 6 www.goodmanmfg.com SS-
BLOWER PERFMANE SPEIFIATIONS (FM & Temperature Rise vs. External Static Pressure) Model Motor Speed Tons A at 0.5 ESP External Static Pressure, (Inches Water olumn) 0. 0. 0.3 0.4 0.5 0.6 0.7 0.8 FM Rise FM Rise FM Rise FM Rise FM Rise FM FM FM High 3,35 9,38 30,60 3,0 33,8 35,044 955 853 0453BXA Med.5,4 3,7 34,3 35,064 37,0 39 938 859 74 Med-Lo 997 40 994 40 960 4 93 43 884 45 87 74 6 Low.5 757 5 753 5 734 54 704 56 674 59 60 54 438 High 3,449 4,409 4,36 45,73 47,0 49,94,36,08 0703BXA Med.5,9 50,7 5,4 5,094 54,046 57 973 904 793 Med-Lo 98 6 96 6 943 63 97 65 888 67 830 764 665 Low.5 750 79 730 8 74 83 69 86 657 90 60 570 50 High 4,069 9,965 30,87 3,756 34,66 36,549,45,75 0704XA Med 3.5,75 34,74 34,667 36,603 37,488 40,40,90,08 Med-Lo 3,437 4,437 4,47 4,369 43,30 45,56,40 984 Notes: Low.5,84 50,77 50,6 5,3 5,095 54,047 98 837 FM in chart is without filter(s). Filters do not ship with this furnace, but must be provided by the installer. All furnaces ship as high-speed cooling and medium-speed heating. Installer must adjust blower cooling & heating speed as needed. For most applications, about 400 FM per ton when cooling is desirable. INSTALLATION IS TO BE ADJUSTED TO OBTAIN TEMPERATURE RISE WITHIN THE RANGE SPEIFIED ON THE RATING PLATE. The chart is for information only. For satisfactory operation, external static pressure should not exceed value shown on the rating plate. The shaded area indicates ranges in excess of the recommended maximum heating static pressure. The above chart is for furnaces installed at 0-000 feet. At higher altitudes, a properly de-rated unit will have approximately the same temperature rise at a particular FM, while ESP at the FM will be lower. SS- www.goodmanmfg.com 7
BLOWER PERFMANE SPEIFIATIONS (ONT.) (FM & Temperature Rise vs. External Static Pressure) Model Motor Speed Tons A at 0.5 ESP External Static Pressure, (Inches Water olumn) 0. 0. 0.3 0.4 0.5 0.6 0.7 0.8 FM Rise FM Rise FM Rise FM Rise FM Rise FM FM FM High 4,970 40,874 4,757 45,667 48,566 5,43,334,8 0904XA Med 3.5,73 46,650 48,57 50,50 5,48 56,33,,079 Med-Lo 3,439 55,4 56,370 58,37 60,60 63,66,078 956 Low.5,83 67,55 69, 7,08 7,06 75,0 93 86 High 5,47 37,4 37,057 39,030 39,978 40,889,784,73 0905DXA Med 4,675 47,686 47,640 48,63 49,557 5,50,455,360 Med-Lo 3.5,489 53,470 54,436 55,409 56,36 58,38,43,30 Low 3,307 6,65 63,34 64,03 66,68 68,096,053 99 High 5,34 46,03 47,09 48,94 5,906 5,88,733,65 55DXA Med 4,678 58,643 60,643 60,577 6,57 64,489,43,339 Med-Lo 3.5,453 68,440 68,46 69,363 7,349 73,34,53,05 Notes: Low 3,59 78,39 79,0 80,8 83,59 85,8,08,05 FM in chart is without filter(s). Filters do not ship with this furnace, but must be provided by the installer. All furnaces ship as high-speed cooling and medium-speed heating. Installer must adjust blower cooling & heating speed as needed. For most applications, about 400 FM per ton when cooling is desirable. INSTALLATION IS TO BE ADJUSTED TO OBTAIN TEMPERATURE RISE WITHIN THE RANGE SPEIFIED ON THE RATING PLATE. The chart is for information only. For satisfactory operation, external static pressure should not exceed value shown on the rating plate. The shaded area indicates ranges in excess of the recommended maximum heating static pressure. The above chart is for furnaces installed at 0-000 feet. At higher altitudes, a properly de-rated unit will have approximately the same temperature rise at a particular FM, while ESP at the FM will be lower. 8 www.goodmanmfg.com SS-
BLOWER PERFMANE SPEIFIATIONS (ONT.) 00 90 80 70 60 50 40 30 0 0 BTU OUTPUT vs TEMPERATURE RISE HART 600 FM 700 800 900 000 00 00 400 600 800 000 00 400 FM FMULAS BTU OUTPUT = FM x.08 x RISE RISE = BTU OUTPUT.08 FM 30 40 50 60 70 80 90 00 0 0 30 40 50 OUTPUT BTU/HR x 000 TEMPERATURE RISE SS- www.goodmanmfg.com 9
BLOWER PERFMANE SPEIFIATIONS (FM & Temperature Rise vs. External Static Pressure) Model Motor Speed Tons A at 0.5 ESP External Static Pressure, (Inches Water olumn) 0. 0. 0.3 0.4 0.5 0.6 0.7 0.8 FM Rise FM Rise FM Rise FM Rise FM Rise FM FM FM High 3,35 9,38 30,60 3,0 33,8 35,044 955 853 0453BXA Med.5,4 3,7 34,3 35,064 37,0 39 938 859 74 Med-Lo 997 40 994 40 960 4 93 43 884 45 87 74 6 Low.5 757 5 753 5 734 54 704 56 674 59 60 54 438 High 3,449 4,409 4,36 45,73 47,0 49,94,36,08 0703BXA Med.5,9 50,7 5,4 5,094 54,046 57 973 904 793 Med-Lo 98 6 96 6 943 63 97 65 888 67 830 764 665 Low.5 750 79 730 8 74 83 69 86 657 90 60 570 50 High 4,069 9,965 30,87 3,756 34,66 36,549,45,75 0704XA Med 3.5,75 34,74 34,667 36,603 37,488 40,40,90,08 Med-Lo 3,437 4,437 4,47 4,369 43,30 45,56,40 984 Low.5,84 50,77 50,6 5,3 5,095 54,047 98 837 High 4,970 40,874 4,757 45,667 48,566 5,43,334,8 0904XA Med 3.5,73 46,650 48,57 50,50 5,48 56,33,,079 Med-Lo 3,439 55,4 56,370 58,37 60,60 63,66,078 956 Low.5,83 67,55 69, 7,08 7,06 75,0 93 86 High 5,47 37,4 37,057 39,030 39,978 40,889,784,73 0905DXA Med 4,675 47,686 47,640 48,63 49,557 5,50,455,360 Med-Lo 3.5,489 53,470 54,436 55,409 56,36 58,38,43,30 Low 3,307 6,65 63,34 64,03 66,68 68,096,053 99 High 5,34 46,03 47,09 48,94 5,906 5,88,733,65 55DXA Med 4,678 58,643 60,643 60,577 6,57 64,489,43,339 Med-Lo 3.5,453 68,440 68,46 69,363 7,349 73,34,53,05 Notes: Low 3,59 78,39 79,0 80,8 83,59 85,8,08,05 FM in chart is without filter(s). Filters do not ship with this furnace, but must be provided by the installer. If the furnace requires two return fi lters, this chart assumes both fi lters are installed. All furnaces ship as high-speed cooling and medium-speed heating. Installer must adjust blower cooling & heating speed as needed. For most jobs, about 400 FM per ton when cooling is desirable. INSTALLATION IS TO BE ADJUSTED TO OBTAIN TEMPERATURE RISE WITHIN THE RANGE SPEIFIED ON THE RATING PLATE. The chart is for information only. For satisfactory operation, external static pressure should not exceed value shown on the rating plate. The shaded area indicates ranges in excess of the recommended maximum heating static pressure. The above chart is for U.S. furnaces installed at 0-000 feet. At higher altitudes, a properly de-rated unit will have approximately the same temperature rise at a particular FM, while ESP at the FM will be lower. 0 www.goodmanmfg.com SS-
BLOWER PERFMANE SPEIFIATIONS (ONT.) 00 90 80 70 60 50 40 30 0 0 BTU OUTPUT vs TEMPERATURE RISE HART 600 FM 700 800 900 000 00 00 400 600 800 000 00 400 FM FMULAS BTU OUTPUT = FM x.08 x RISE RISE = BTU OUTPUT.08 FM 30 40 50 60 70 80 90 00 0 0 30 40 50 OUTPUT BTU/HR x 000 TEMPERATURE RISE SS- www.goodmanmfg.com
DUAL$AVER ONFIGURATION & OPERATION THERMOSTATS Model HT8-60 H70TG HSATG H0TWR Description ooling/heating, Mechanical ooling/heating, Digital, Non-programmable ooling/heating, Mechanical Heating Only, Mechanical www.goodmanmfg.com SS-
WIRING DIAGRAM 4V THERMOSTAT ONNETIONS BR BR 4 VA HUMIDIFIER G R W DIAGNOSTI LED 4 VA 5 VA 5 VA HOT AND PARK TERMINALS OOL-H APAIT INTEGRATED ONTROL MODULE ON FUSE OFF ND STAGE DELAY MODE HEAT OFF DELAY FATY SETTINGS SHOWN * Y SEE NOTE 6 HEAT-H SEE NOTE 4 * * * XFMR-H (HI) BL (MED) (MED LOW) (LOW) LINE-H FS 3 XFMR-N 6 5 4 9 8 7 0 5 VA NEUTRAL TERMINALS PK YL PK BL YL BR GR PK BL YL GR BLOWER OMPARTMENT DO SWITH (OPEN EN DO OPEN) BR 4V THERMOSTAT ONNETIONS INTEGRATED ONTROL MODULE G Y W R TO MIRO TH (3) XFMR-H FS IGN IND TR (6) (8) MV (9) MVH () MVL() PS (0) PSO (4) HLI (7) HLO () RO () RO (5) LO HEAT-H HI HEAT-H HUMIDIFIER NO FLAME SENS HOT SURFAE IGNITER ID BLWR FRONT OVER PRESSURE SWITH OOL-H 4 VA 5 VA IRULAT BLWR INTEGRATED ONTROL MODULE NO 40 VA TRANSFMER IR-N XFMR-N ID-N GAS HI VALVE PM ID BLOWER PRESSURE SWITH INTEGRATED ONTROL MODULE BLOWER OMPARTMENT PU EA-H ELETRONI AIR LEANER EA-N BURNER OMPARTMENT MANUAL RESET AUXILIARY LIMITS () IN UPFLOW BLOWER DEK () IN 'FLOW BLOWER HOUSING INDUED DRAFT BLOWER LINE-H LINE-N JUNTION BOX DO SWITH DISONNET PU N O YL PK BL L N TO 5VA/ Ø /60 HZ POWER SUPPLY WITH OVERURRENT PROTETION DEVIE ID BLOWER PRESSURE SWITH IRUIT ONNET HOT SURFAE IGNITER 4 VA HUMIDIFIER PM HI 3 BR GAS VALVE N O FRONT OVER PRESSURE SWITH GR BL FLAME SENS JUNTION BOX N L 0 3 4 5 6 7 STEADY ON = NMAL OPERATION OFF = ONTROL FAILURE FLASH = FLASHES = PRESSURE SWITH STUK LOSED 3 FLASHES = PRESSURE SWITH STUK OPEN 4 FLASHES = OPEN HIGH LIMIT 5 FLASHES = FLAME SENSE WITHOUT GAS VALVE 6 FLASHES = 7 FLASHES = LOW FLAME SIGNAL ONTINUOUS/RAPID FLASHES = REVERSED 5 VA POLARITY LOW VOLTAGE (4V) LOW VOLTAGE FIELD HI VOLTAGE (5V) HI VOLTAGE FIELD JUNTION TERMINAL INTERNAL TO INTEGRATED ONTROL PLUG ONNETION EQUIPMENT FIELD FIELD SPLIE SWITH (TEMP.) IGNITER SWITH (PRESS.) OVERURRENT PROT. DEVIE OL ODES: YL YELLOW ANGE PU PURPLE GN GREEN BLAK PK PINK BR BROWN ITE BL BLUE GRAY RED 040F00098 REV.-- NOTES:. SET HEAT ANTIIPAT ON ROOM THERMOSTAT AT 0.7 AMPS.. MANUFATURER'S SPEIFIED REPLAEMENT PARTS MUST BE USED EN SERVIING. 3. IF ANY OF THE IGINAL WIRE AS SUPPLIED WITH THE FURNAE MUST BE REPLAED, IT MUST BE REPLAED WITH WIRING MATERIAL HAVING A TEMPERATURE RATING OF AT LEAST 05. USE OPPER ONDUTS ONLY. 4. IF HEATING AND OOLING BLOWER SPEEDS ARE NOT THE SAME, DISA JUMPER BEFE ONNETING BLOWER LEADS. UNUSED BLOWER LEADS MUST BE PLAED ON "PARK" TERMINALS OF INTEGRATED ONTROL TAPED. 5. UNIT MUST BE PERMANENTLY GROUNDED AND ONFM TO N.E.. AND LOAL ODES. 6. TO REALL THE LAST 5 FAULTS, MOST REENT TO LEAST REENT, DEPRESS SWITH F ME THAN SEONDS ILE IN STANDBY (NO THE RMOSTAT IN PUTS) Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring. WARNING High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. SS- www.goodmanmfg.com 3
WIRING DIAGRAM 4V THERMOSTAT ONNETIONS BR BR 4 VA HUMIDIFIER G W R DIAGNOSTI LED 4 VA 5 VA 5 VA HOT AND PARK TERMINALS OOL-H APAIT INTEGRATED ON FUSE ONTROL MODULE OFF ND STAGE DELAY MODE HEAT OFF DELAY FATY SETTINGS SHOWN * Y SEE NOTE 6 HEAT-H SEE NOTE 4 (HI) * * * XFMR-H BL (MED) (MED LOW) (LOW) LINE-H FS 3 6 5 4 9 8 7 0 5 VA NEUTRAL TERMINALS PK YL PK BL YL BR GR PK BL YL GR BLOWER OMPARTMENT DO SWITH (OPEN EN DO OPEN) BR 4V THERMOSTAT ONNETIONS INTEGRATED ONTROL MODULE G Y W R TO MIRO TH (3) XFMR-H FS IGN IND TR (6) (8) MV (9) MVH () MVL() PS (0) PSO (4) HLI (7) HLO () RO () RO (5) HI LO HEAT-H HEAT-H HUMIDIFIER NO FLAME SENS HOT SURFAE IGNITER ID BLWR FRONT OVER PRESSURE SWITH OOL-H 4 VA 5 VA IRULAT BLWR INTEGRATED ONTROL MODULE NO 40 VA TRANSFMER GAS HI VALVE PM ID BLOWER PRESSURE SWITH LINE NEUTRALS INTEGRATED ONTROL MODULE BLOWER OMPARTMENT PU EA-H ELETRONI AIR LEANER BURNER OMPARTMENT MANUAL RESET AUXILIARY LIMITS () IN UPFLOW BLOWER DEK () IN 'FLOW BLOWER HOUSING INDUED DRAFT BLOWER LINE-H DO SWITH JUNTION BOX DISONNET PU N O YL PK BL L N TO 5VA/ Ø /60 HZ POWER SUPPLY WITH OVERURRENT PROTETION DEVIE ID BLOWER PRESSURE SWITH IRUIT ONNET HOT SURFAE IGNITER 4 VA HUMIDIFIER PM HI 3 BR GAS VALVE N O FRONT OVER PRESSURE SWITH GR BL FLAME SENS JUNTION BOX N L 0 3 4 5 6 7 STEADY ON = NMAL OPERATION OFF = ONTROL FAILURE FLASH = FLASHES = PRESSURE SWITH STUK LOSED 3 FLASHES = PRESSURE SWITH STUK OPEN 4 FLASHES = OPEN HIGH LIMIT 5 FLASHES = FLAME SENSE WITHOUT GAS VALVE 6 FLASHES = 7 FLASHES = LOW FLAME SIGNAL ONTINUOUS/RAPID FLASHES = REVERSED 5 VA POLARITY LOW VOLTAGE (4V) LOW VOLTAGE FIELD HI VOLTAGE (5V) HI VOLTAGE FIELD JUNTION TERMINAL INTERNAL TO INTEGRATED ONTROL PLUG ONNETION EQUIPMENT FIELD FIELD SPLIE SWITH (TEMP.) IGNITER SWITH (PRESS.) OVERURRENT PROT. DEVIE OL ODES: YL YELLOW ANGE PU PURPLE GN GREEN BLAK PK PINK BR BROWN ITE BL BLUE GRAY RED 040F00098 REV. B NOTES:. SET HEAT ANTIIPAT ON ROOM THERMOSTAT AT 0.7 AMPS.. MANUFATURER'S SPEIFIED REPLAEMENT PARTS MUST BE USED EN SERVIING. 3. IF ANY OF THE IGINAL WIRE AS SUPPLIED WITH THE FURNAE MUST BE REPLAED, IT MUST BE REPLAED WITH WIRING MATERIAL HAVING A TEMPERATURE RATING OF AT LEAST 05. USE OPPER ONDUTS ONLY. 4. IF HEATING AND OOLING BLOWER SPEEDS ARE NOT THE SAME, DISA JUMPER BEFE ONNETING BLOWER LEADS. UNUSED BLOWER LEADS MUST BE PLAED ON "PARK" TERMINALS OF INTEGRATED ONTROL TAPED. 5. UNIT MUST BE PERMANENTLY GROUNDED AND ONFM TO N.E.. AND LOAL ODES. 6. TO REALL TH E LAST 5 FAULTS, MOST REENT TO LEAST REENT, DEP RESS SWITH F ME THAN SEONDS W HILE IN STANDBY (NO THERMOSTA T INPUTS) Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring. WARNING High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. 4 www.goodmanmfg.com SS-
AESSIES Accessory Description 0453BXA 0703BXA 0704XA 0904XA 0905DXA 55DXA LPM-03B LP onversion Kit (Gas Valve) LPM-05 LP onversion Kit (Springs & Orifi ce) LPLP0 LP Gas Low Pressure Kit GSAS Electronic Air leaners (-0, -, -, -8) GMU Media Air leaners (60, 00, 65, 05) HANG High Altitude Natural Gas Kit HANG High Altitude Natural Gas Kit HALP0 High Altitude LP Gas Kit 3 3 3 3 3 3 HAPS7 High Altitude Pressure Switch Kit 3 3 3 3 3 3 EFR0 External Filter Rack DVK-0 Horizontal/Vertical oncentric Vent Kit ( ) --- --- --- --- DVK-30 Horizontal/Vertical oncentric Vent Kit (3 ) 070K00000S Flush-mount Vent Kit Indicates accessories available for this model Indicates 7,00 to 9,000 altitude Indicates 9,00 to,000 altitude 3 Indicates 7,00 to,000 altitude Note: All installations above 7,000 require a pressure switch change. For installation in anada, furnaces are certifi ed only to 4,500. SS- www.goodmanmfg.com 5
AESSIES Accessory Description 0453BXA 0703BXA 0704XA 0904XA 0905DXA LPM-03B LP onversion Kit (Gas Valve) LPM-05 LP onversion Kit (Springs & Orifi ce) LPLP0 LP Gas Low Pressure Kit GSAS Electronic Air leaners (-0, -, -, -8) GMU Media Air leaners (60, 00, 65, 05) HANG High Altitude Natural Gas Kit HANG High Altitude Natural Gas Kit HALP0 High Altitude LP Gas Kit 3 3 3 3 3 3 HAPS7 High Altitude Pressure Switch Kit 3 3 3 3 3 3 EFR0 External Filter Rack 55DXA DVK-0 Horizontal/Vertical oncentric Vent Kit ( ) --- --- --- --- DVK-30 Horizontal/Vertical oncentric Vent Kit (3 ) Flush-mount Vent Kit Indicates accessories available for this model Indicates 7,00 to 9,000 altitude Indicates 9,00 to,000 altitude 3 Indicates 7,00 to,000 altitude Notes All installations above 7,000 require a pressure switch change. For installation in anada, furnaces are certifi ed only to 4,500. Downflow Floor base: When the model is installed directly on a wood fl oor, a downfl ow fl oor base must be used. Those model numbers are: FB7, FB and FB4. Goodman Manufacturing ompany, L.P., reserves the right to discontinue, or change at any time, specifications or designs without notice or without incurring obligations. 008 Goodman Manufacturing ompany, L.P. Houston, Texas Printed in the USA. 6 www.goodmanmfg.com SS-