PRODUCT #: SJPFB002 ITEM: Sanijet Portable Foot Bath BRAND: Sanijet SOURCE FOR PURCHASE: SpaEquip, Inc. 211 Wappo Ave., Calistoga, CA 94515 p: 707.737.1100 f: 707.737.1150 www.spaequip.com Please contact SpaEquip for preferred pricing. FEATURES: Sanijet Portable Foot Bath features: - Two patented whisper-quiet Pipeless jets - Independently certified hospitalgrade disinfection - State-of-the-art induction motors - Discharge pump for quick draining - Fill hose - Two-piece lid with footrest for client comfort - Available in three attractive colors: White, Biscuit, and Almond SPECIFICATIONS: Dimensions: 27"L x 20"w x 15"H Electrical: 115V, 60Hz/2 amp electrical service required Suggested Outlet: Adjacent to unit Plumbing: None Notes: 4.5 gallon capacity Warranty: Pending Certifications: See Manufacturer's Statement Country of Origin: United States Installed By: SpaEquip (if setup is included with order) or Client www.spaequip.com p: 707.737.1100 f: 707.737.1150 Page 1 of 11
PIPELESS WHIRLPOOL FOOT BATH OWNER S MANUAL Model: FB2-S115 www.spaequip.com p: 707.737.1100 f: 707.737.1150 Page 2 of 11
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS...3 WARNINGS..4 INSTRUCTIONS PRIOR TO USE. 5 GROUNDING INSTRUCTIONS.... 5 HOW TO USE...6 HOW TO DRAIN AND CLEAN.....7 HOW TO STORE THE FOOT BATH.... 9 LIMITED WARRANTY..9 HOW TO OBTAIN SERVICE..10 PRODUCT CERTIFICATIONS...10 2 www.spaequip.com p: 707.737.1100 f: 707.737.1150 Page 3 of 11
SANIJET Pipeless Whirlpool Foot Bath Thank you for purchasing the revolutionary Pipeless Whirlpool Foot Bath. The Pipeless Whirlpool Foot Bath joins SANIJET s luxurious Pipeless Whirlpool Baths and Pipeless Whirlpool Pedicure Sinks in providing excellent hydrotherapy, quiet operation and the ability for quick, easy and certified cleanliness. SANITATION CERTIFICATION: The National Sanitation Foundation (nsf.org) confirmed that SANIJET s Pipeless system can be completely cleaned and disinfected, even if system cleaning has been neglected. For more information about SANIJET s Pipeless Whirlpool Baths and Pipeless Whirlpool Pedicure Sinks, please visit our website at www.sanijet.com IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING: When using an electrical appliance, basic precautions should always be followed. Read and follow all instructions before using this foot bath. DANGER To reduce the risk of electrical shock: 1. Always unplug this appliance from the electrical outlet and store the power cord when not in use. 2. DO NOT use this appliance while bathing or in a shower. 3. DO NOT place or store this appliance where it can fall or be pulled into water. 4. DO NOT reach for any electrical object that has fallen into water. Unplug immediately. INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS: 1. DO NOT leave this appliance unattended when it is connected to a power source. 2. DO NOT carry this appliance by the supply cord or use the cord as a handle. 3. DO NOT drop or insert anything into any jet opening. 4. DO NOT operate this unit without the complete jet assembly installed or without water filled to the water level indicator above the jets. 5. DO NOT overfill. 6. DO NOT stand on or in the foot bath. Use only while seated. 7. Use the SANIJET Pipeless Foot Bath only for its intended purpose: a fill and drain, appliance for foot and ankle hydro massage. DO NOT use attachments not recommended by the manufacturer. 3 www.spaequip.com p: 707.737.1100 f: 707.737.1150 Page 4 of 11
WARNINGS: 1. Risk of accidental injury or drowning: Children, invalid or disabled persons should not use a hydro massage foot bath without adult supervision. 2. To avoid injury, exercise care when entering or exiting the foot bath. 3. Risk of electric shock: DO NOT permit electric appliances (e.g. hair dryer, lamp, telephone, radio, television, etc.) to be within 5 feet (1.5m) of this appliance. 4. Keep the cord away from heated surfaces. 5. Connect this appliance only to a properly grounded outlet. (See Grounding Instructions below.) Do not remove, modify or immerse the integral GFCI on the power cord. 6. Risk of hypothermia and possible drowning: Water temperature in excess of 104º F (38 ºC) may be injurious to your health. Check and adjust water temperature before use. 7. RISK OF ELECTRIC SHOCK: Disconnect from electrical supply before servicing. 8. Hydrotherapy should be pleasant and comfortable. Should you experience any pain or discomfort while using the foot bath, discontinue use immediately and consult your physician. 9. Consult your physician if you are diabetic, have poor circulation, if any area of your feet or legs is inflamed, has an open wound or if you have any other questions about whether you should be using hydro massage equipment. 10. Unless thoroughly cleaned after each use, bath residue will buildup within the jets and on the surface area of any whirlpool foot bath, which can promote the growth of bacteria. 4 www.spaequip.com p: 707.737.1100 f: 707.737.1150 Page 5 of 11
INSTRUCTIONS Prior to Use WARNING: When using electrical products, basic precautions should always be followed including the following: 1) IMPORTANT: Read complete instructions before use. Each Pipeless Whirlpool Foot Bath arrives ready for use. 2) This unit requires a 115 volt, 60 Hertz, 2 Amp service and is provided with a 10 cord with an integral Ground Fault Circuit Interrupter (GFCI) and NEMA 5-15P electrical plug. A grounded electrical outlet is required. 3) Remove the foot bath from the carton and retain the shipping carton and packing material to reuse in case service becomes necessary. DO NOT lift the foot bath by its handle or electrical cord. 3) Immediately upon receipt, inspect the entire unit for any obvious damage BEFORE using. Should inspection reveal any damage or defect in the finish, do not use the foot bath. SANIJET Corporation s responsibility for shipping damage ceases upon delivery of the product in good order to the carrier. Refer any claim for damage to the carrier. 4) All foot bath units are factory tested for proper operation and watertight connections prior to shipping. Note: Prior to use, the foot bath must be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling. GROUNDING INSTRUCTIONS This unit must be grounded. The integral GFCI should be tested on a routine basis. To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, there is a ground fault, indicating the possibility of electrical shock. DO NOT USE THE UNIT. Disconnect the unit and have the problem corrected by a qualified service representative or an electrician before using. 5 www.spaequip.com p: 707.737.1100 f: 707.737.1150 Page 6 of 11
HOW TO USE 1. Fill the unit with water at the desired temperature above the jets to the water level indicator. A fill hose with a connector to attach to a typical sink spout is included or the unit can be filled with the use of a container. 2. Move the unit to the place where it will be used and be sure that it is on a level, solid floor. Note: The front two casters have locking mechanisms to prevent the unit from moving during use. Be sure the locking mechanisms are disengaged before attempting to move the unit. A handle is built into the top of the unit for easy maneuverability. Before moving the unit filled with water, place the two removable lids on the tank to prevent water from splashing onto the floor. (See Illustration #1.) Illustration #1 3. Plug the unit into a grounded electrical outlet. 4. To activate or deactivate this appliance, press the ON/OFF button. 5. Bath additives (including oil based products) can be used in a SANIJET Pipeless Foot Bath, since their residue can be easily cleaned. CAUTION: Use only low foaming additives. 6. You should always be in a seated position when putting your feet in or removing them from the foot bath. WARNING: NEVER STAND IN THE FOOT BATH. 7. During use of the foot bath the front lid can be used as a foot rest as well as assist in maintaining water temperature and reduce splashing. 6 www.spaequip.com p: 707.737.1100 f: 707.737.1150 Page 7 of 11
HOW TO DRAIN AND CLEAN To maintain your SANIJET Pipeless Whirlpool Foot Bath at a maximum level of hygiene, thoroughly clean the tub shell and jets after each use with a nonabrasive antibacterial cleaner, rinse thoroughly, and dry completely. See page 8 for complete cleaning procedure. NEVER use abrasive cleaners on the foot bath. Procedure to Drain the Foot Bath: 1. Turn off the foot bath by pushing the ON/OFF button. 2. Unplug the foot bath from the electrical outlet and store the cord. 3. Put both removable lids on the tank before moving the foot bath to the area where the tank will be drained and then remove the lids. 4. Place the Discharge Pump on the flat round surface in the bottom of the foot bath. (See Illustration #2) Illustration #2 5. Extend the hose connected to the Discharge Pump to the area where the water is to be drained (sink). Use the suction cup provided to secure the hose to the side of the sink and turn on the discharge pump by plugging the pump s power cord into a grounded circuit. (See Illustration #3) 6. When the foot bath appears to be empty, continue running the pump while removing it from the interior of the foot bath and place it in the sink or chosen draining area. As soon as the pump and hose are both fully in the sink unplug the power cord to turn off the discharge pump. Fresh water can be used to rinse out the tank during the draining procedure. (See Illustration #3.) **Do not leave the pump running in the draining area or in a dry foot bath for more than a few seconds because it may result in damage to the discharge pump. **The power cord cannot be replaced; in case of any damage to the power cord the entire discharge pump must be replaced. Illustration #3 7 www.spaequip.com p: 707.737.1100 f: 707.737.1150 Page 8 of 11
Procedure to Clean the Foot Bath: STEP 1: Preparation, Jet Removal, and Cleaning Drain the Footbath according to draining procedure. Rotate the Jet Assemblies counterclockwise and remove them from the Jet Cases in the Footbath. Disassemble the Jet Assemblies (three pieces) for further cleaning. Spray the Jet Assembly Pieces, Footbath Interior, and Jet Cases with *Cleaner / Disinfectant. Use a clean cloth to clean the Jet Assembly pieces, removing any visible soil. Scrub all surfaces of the Footbath and Jet Cases. Rinse all surfaces with tap water Illustration #4 Removing Jet Assembly from Jet Case STEP 2: Disinfection and Re-Assembly Spray the Jet Assembly pieces, Jet Cases and Foot Bath until thoroughly wet with *Cleaner / Disinfectant and allow them to set for 1 minute. Rinse disinfectant from all surfaces. Dry the Jet Assembly pieces, Jet Cases, and the Footbath, with a clean cloth. Reassemble Jet Assemblies and reinsert them into Jet Cases, rotate them in a clockwise manner to secure them in position. Detergent / Disinfectant Selection: Illustration #5 Jet Assembly *SANIJET recommends the use of an EPA registered cleaner / disinfectant with tuberculocidal, germicidal, pseudomonacidal, Fungicidal and Virucidal efficacy. Do not use abrasive cleaners on the Pedicure Basin or Jet Assemblies. SANIJET suggests *DISPATCH Hospital Cleaner Disinfectant with Bleach as a suitable cleaner disinfectant for use with the above procedure. Dispatch - EPA Reg. No. 56392-7; EST. No. 62801-MI-001. Kills bacteria and viruses in 1 minute and TB in 30 seconds. 8 www.spaequip.com p: 707.737.1100 f: 707.737.1150 Page 9 of 11
HOW TO STORE THE FOOT BATH 1. Replace the jet assemblies into the jet casings by reversing the procedure shown in Illustration #4. 2. Store the power cord inside the recess cavity at the base of the foot bath. 3. Store the fill hose and Discharge Pump inside the tank or in another location. 4. Replace both lids. 5. Store away from direct exposure to sunlight to prevent discoloration of the foot bath. TWO (2) YEAR LIMITED WARRANTY PORTABLE FOOT BATH Scope: SANIJET will provide the parts and labor at its factory to repair any defect in materials or workmanship, unless excluded below, reported in writing to SANIJET within the warranty period. SANIJET may elect to replace the product or the affected component if it determines in its sole discretion that the defect cannot be satisfactorily repaired. Warranty Period: The warranty period is two (2) years after the date the product is first purchased for use and not for resale. SANIJET may require you to establish the date of purchase by invoice or other documentation satisfactory to SANIJET. Exclusions: This warranty does not cover the metallic drain plate, fading from exposure to direct sunlight, freight damage, or mishandling, abuse, misuse, neglect, accident or natural disaster. Shipping: You are responsible for shipping the product to Sanijet for warranty service and for return shipping charges after repair or replacement. Claims: Report the problem to SANIJET s customer service department BEFORE the warranty period expires. The address is 1461 South Beltline Road, Suite 100, Coppell, Texas 75019. Toll Free Numbers: Telephone 877-934-0477; Fax 877-834-0477. Toll Numbers: Telephone 972-745-2283; Fax 972-745-2285. E-mail: customersvc@sanijet.com. Unauthorized Repair: Any completed or attempted repair or alteration by anyone outside of SANIJET s factory not expressly authorized in writing by SANIJET will VOID this warranty. Dealer Warranties: No dealer or distributor has any authority to bind SANIJET to any changes or additions to this warranty. Limitation On Damages: To the fullest extent allowed by law, SANIJET disclaims and excludes liability for consequential and incidental damages including, but not limited to, lost profits, loss of business reputation, out of pocket expenses, damage to property other than the warranted product, mental anguish and punitive damages. The maximum amount of SANIJET s liability will be the amount you paid for the product. Some states limit or do not allow the exclusion or limitation of incidental or consequential damages, so some or all of these limitations may not apply to you. State Law Rights: This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. THE DURATION OF ANY IMPLIED WARRANTIES UNDER STATE LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE WARRANTY PERIOD DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty lasts, so this limitation may not apply to you. 9 www.spaequip.com p: 707.737.1100 f: 707.737.1150 Page 10 of 11
HOW TO OBTAIN SERVICE For Customer Service contact: SANIJET Customer Service Department Toll Free Tel. (877) 934-0477 Toll Free Fax (877) 834-0477 E-MAIL: CustomerService@sanijet.com SANIJET Corporation 1461 South Beltline Road, Suite 100 Coppell, Texas 75019 Tel. (972) 745-2283; Fax (972) 745-2285 www.sanijet.com Product Certifications: The Pipeless system is manufactured with CUL recognized components (motors, jets and controls). NSF Protocol P182 Pipeless Hydrotherapy 2004, SANIJET Corporation Printed in U.S.A. 75027/Rev. 09/2004 10 www.spaequip.com p: 707.737.1100 f: 707.737.1150 Page 11 of 11