ADA 00 AREA OF RESCUE SYSEM VERSION.a OPERAIONS & INSALLAION MANUAL HOUSING DEVICES, INC 0R MYSIC AVE. MEDFORD, MA 0 0000
ABLE OF CONENS INRODUCION Page SYSEM DESCRIPION Page SYSEM OPERAION Page MASER SAION OPERAION Page AREA SAION OPERAION Page SYSEM CONSRUCION Page MASER SAION INDICAORS & CONROLS Page 6 AREA SAION INDICAORS & CONROLS Page 6 POWER REQUIREMENS Page SYSEM COMPONENS Page MASER SAION Page AREA SAION Page RELAY CARD CABINE Page RELAY CARD Page CONROL BOARD Page BAERY BACKUP SYSEM CABINE Page AMPLIFIER Page BRAILLE INSRUCIONAL SIGN Page ILLUMINAED AREA SAION SIGN Page INSALLAION Page UNPACKING Page BACK BOX Page SURFACE MOUNING COLLAR Page MASER SAION Page 0 AREA SAION Page 0 RELAY CARD CABINE Page 0 BAERY BACKUP SYSEM CABINE Page 0 INSRUCIONAL SIGNS Page 0 SYSEM WIRING AND CONNECIONS Page GENERAL Page MASER SAION WIRING Page AREA SAION WIRING Page RELAY CARD CABINE WIRING Page BAERY BACKUP SYSEM WIRING Page WIRE & CABLE LEGAND Page ROUBLESHOOING Page 6 APPENDIX WIRING DIAGRAMS Page ADA 00 System Riser Diagram Page ADA00 Relay Card Cabinet Diagram Page ADA00 Master Station Riser Diagram Page 0 ADA00 Dual Master Riser Diagram Page ADA00 Connection Diagram Page ADA00 Connection Diagram Page ADA00 Battery Backup Riser Diagram Page ADA00 Master rouble Light Directions (installing the shunt) Page ADA00 00 Phone Dialer Diagram Page 6 ADA RM Strobe Connection Diagram (Master Station & ) Page Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
Introduction Congratulations on your decision to choose the ADA 00 Area of Rescue System from Housing Devices, Inc. Since the inception of the American with Disabilities Act the ADA 00 has been the superior choice of architects and engineers throughout the U.S.A. he ADA 00 Area of Rescue System incorporates state of the art design developed from years of actual field experience installing over 0,000 devices at thousands of sites. he ADA 00 is a hard wired system that can be operated independently of any other building systems or interfaced with your existing annunciator or fire alarm system. It is easy to install and designed to provide you with years of trouble free use with virtually no maintenance needed. he new ADA 00 delivers unparalleled performance with the same superior quality and support that companies throughout the country have come to expect from Housing Devices Inc. 0000. Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
System Description he ADA 00 is a modular, handsfree Area of Refuge System with dual audio and visual alarms and built in supervision capabilities designed to comply with the Americans with Disabilities Act. he ADA 00 Area of Refuge System is a hard wired system needing only a simple connection to AC power and/or auxiliary DC power to operate. he system can be operated independently of any other building systems or interfaced with your existing annunciator or fire alarm system. Each ADA 00 installation consists of at least one Master Station, one or more s, Relay Card Cabinet (with one Control Board and one or more Relay Cards, and Battery Backup Power Supply System. Each Master Station and each are mounted using either a Flush Back Box or Surface Mounting Collar. amper Proof hardware and a amper Driver (socket only) are also included with each system. Optional system components include Braille Instructional Signs with tactile lettering, Illuminated Area of Refuge signs with universal mounting hardware and independent battery backup system (also available without battery backup), telephone dialers ( number capacity) and remote mounted strobe lights. (blue, red, & standard white) System Operation All conversations are controlled at the Master Station using the specific ALK and LISEN metal buttons identified for each location in the system. Operation of the system is confirmed at both the Master Station and s by means of audio and visual indicators. hese indicators verify to the security attendant that the system is fully operational. hey identify locations requesting assistance, alert the security attendant to respond to the request(s) for help from the location(s), and establish twoway communications. All conversations at the are handsfree after the initial system request. Master Station Operation When the system is activated by a request for help from an, a 0 dba sound will occur through the Master Station and a steady red LED identified with a specific location (engraved label) will illuminate. he security attendant operates the system by depressing the metal ALK button on the Master Station for each specific location to establish a dialog with the person in need of help. his will: Silence the piezoelectric alarms at both the Master Station and the Illuminate the red LED labeled HELP COMING at the Open up a twoway communication channel with the so that the security attendant can converse with the person requesting help Depressing the metal LISEN button at the Master Station enables the security attendant to hear the person s response Resetting the system is accomplished by turning the reset key at the Master Station. his will extinguish the HELP COMING light(s) at all (s) and the Master Station. NOE: he alk button must be depressed at each specific to Listen to that station EXAMPLE: he attendant is speaking to Area # pressing the alk button if he moves to Area # and presses the Listen button he will still be listing to Area # Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
Operation Depressing the large PUSH FOR HELP button on the activates the system. his initiates a request to the Master Station and: Sounds the piezoelectric alarms at both the Master Station and the Illuminates the red LED labeled HELP REQUESED at the and the red LED corresponding to that specific at the Master Station Enables handsfree twoway communication at the upon acknowledgement by the security attendant at the Master Station Resetting the is accomplished by turning the reset key at the Master Station. his will extinguish the HELP COMING LED at the (s) and the red LED(s) at the Master Station, and return them to the standby mode. System Construction All external system panels are constructed using 6 gauge 0 # finish (0.06 ) stainless steel providing architecturally pleasing design and years of trouble free performance. ADA 00 Master and s are designed, manufactured, and tested by Housing Devices to ensure the highest standards of system integrity and performance. System interconnections are accomplished using labeled captive screw plugin connectors to simplify and expedite installation. he system s independent supervision helps to promote easy troubleshooting via rapid problem identification and repair. he ADA 00 selfidentifies system problems using its supervisory circuits to illuminate amber colored trouble LEDs located at the Master Station for each independent location that is affected. If a system wide power fault occurs the ADA 00 continues to operate utilizing the battery backup system ensuring continued emergency call system viability and availability, for a minimum of 0 minutes. Master Station Indicators and Controls Visual Indicators he Master Station utilizes red colored SuperBrite LEDs (one per each location or area ) to visually indicate a request for assistance has originated from an location. he Master Station utilizes amber colored SuperBrite LEDs (one per each location or area ) to visually indicate that a fault has occurred at a particular (s) or in the wiring between the Master Station and Area Station(s), or if the Master Station has failed. Audio Indicators he Master Station utilizes a piezoelectric alarm to generate a 0 dba signal through the Master Station to aurally indicate to the security attendant that a request for help has been generated. It will remain active until the security attendant at the Master Station initiates a response by depressing the metal ALK button on the Master Station. System Power Indicator A green colored SuperBrite LED located directly beneath the system RESE.power key switch indicates system power. When the system is operating normally, the LED will be illuminated. Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
Communication Controls here are two large (/6 ) flat metal buttons under headings labeled ALK and LISEN for each Area Station location in the system. he name of each location is permanently engraved on the Master Station next to the specific buttons for that location. Optional engraved directories identifying each are also available to provide for future system growth or changes without having to power down the system, or to dismantle or exchange the Master Station. hese controls are only active when help has been requested from an location. Communications from the Master Station may be made to one or more s at the same time in order to maximize response to emergency situations in the event that they are of a more building wide nature. System Reset Control A keyed switch with momentary RESE position is provided on the Master Station to reset the entire system following a request(s) for help. he normal position of the key switch is straight up or ON. he ON position of the key switch is the only position in which the key may be removed. If a fault occurs, the system is designed to stay on line and continue to provide emergency call capability from each without the system needing to be RESE. Indicators and Controls he communicates directly with the Master Station. Depressing the PUSH FOR HELP button initiates a request for assistance from the Master Station, and permits handsfree (from the Area Station) twoway communications between the Master Station and (s). Visual Indicators he utilizes two red colored SuperBrite LEDs to visually indicate that a request for help has been generated from the location and that the HELP REQUESED LED is acknowledged from a security attendant at the Master Station. Permanently engraved and backfill painted acknowledgement labels ( HELP REQUESED and HELP COMING ) are located next to each LED. Audio Indicators he utilizes a piezoelectric alarm to generate a 0 dba signal through the to aurally indicate to the caller that a request for help has been generated. It will remain active until the security attendant at the Master Station initiates a response by depressing the metal ALK button on the Master Station. Communication Controls A large ( ) domed stainless steel button surface engraved with the words PUSH FOR HELP backfill painted in red is used to initiate a request for help from an. Housing Devices, Inc. Page 6 www.housingdevices.com Medford, MA 0 Copyright 0000
Power Requirements he ADA 00 Emergency Call System has an input voltage of 0 VAC, converting to VDC @ amp. his connection is made at the systems Relay Card Cabinet houses the system s electronics.he ADA 00 Area of Refuge System also features a VDC battery backup system supplying.0 amp for each group of ten (or multiples of 0) s to ensure auxiliary power in the event of a power outage. Larger power supplies are included with larger systems. System Components Master Station he Master Station is a 6 gauge 0 # finish (0.06) stainless steel vandal resistant unit that is the heart of the system from which all calls are controlled. Each Master Station contains a 0 dba piezoelectric audio alarm, red, green and amber colored LEDs as visual indicators, a system RESE key switch, and engraving identifying each location. he size of the standard ( areas) flush mounted Master Station is x. Master Station size depends on the number of s in the system. Consult the manufacturer for larger Master Station dimensions. A Master Station can accommodate up to 60 s. he baseline Master Station accommodates s. he next larger size Master Station accommodates 60 s. he next larger size Master Station accommodates s, then 60 s and so forth, up to 60 Area Stations. Multiple Master Stations may be used to accommodate larger systems. Master Stations should be mounted in an appropriate and secure area (manned location) typically adjacent to other security equipment. s are x 6 gauge 0 # finish (0.06) stainless steel vandal resistant units that are used to communicate directly with the Master Station. Each features a 0 dba piezoelectric audio alarm, red colored LEDs as visual indicators and a large ( ) domed stainless steel engraved and backfill red painted panic button labeled PUSH FOR HELP. s should be mounted in areas where they are visible and easily accessible by anyone needing help. Relay Card Cabinet he standard size Relay Card Cabinet ( x x ) holds up to 0 Relay Cards, one per each in the system. Larger systems will use larger cabinets with more Relay Cards. Larger cabinets to hold up to 0 relay cards are available ( x x ) Relay Card he Relay Card is the electronic brain for an ; one card is supplied & mounted in the Relay Card Cabinet for each used in the system. Control Board he Control Board is located in the Relay Card Cabinet and provides electronic support for the Master Station and Battery Backup System. One Control Board is used per system. Optional K relay is available for use as a dry contact. Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
Battery Backup System Cabinet he standard Battery Backup System Cabinet houses the components that encompass the Battery Backup System, which provides VDC continuous power to the ADA 00 Emergency Call System in the event of a power failure. he system monitors for AC power failure, AC and DC surge suppression, and no/low battery indications. It features autoresetting overload protection, visual AC and DC power indicators and builtin battery charger circuitry. he system includes two VDC sealed lead acid batteries (rated @. amp hours each),.0 amp battery charger, VAC 0VA transformer, and has a continuous output current of 00mA. UL listed Battery Backup Systems are supplied if specified. Amplifier he Housing Devices ADA Amplifier, powered by VDC, located in the Battery Backup System Cabinet processes the audio communications for the entire system. he audio volume is used to adjust the volume. Braille Instructional Sign (option) Satin stainless.0 laminated to.06 black plex backplate, helvetica 6 condensed type red tactile.0 applique clear raster braille. Four. corner holes. to center of hole. Eased edges. Vertical grain. H x.w x.0d with #0. amper wood screws Illuminated Sign (option) An optional illuminated sign with universal mounting hardware, dual face, LED lightning, & Chevron directional knockouts is placed above each for easy visual identification of the s location. Illuminated signs are available with or without their own independent battery backup system. Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
Installation Installation of the new ADA 00 Area of Refuge System by Housing Devices, Inc., is simple to accomplish and very straight forward from an installer s perspective. Newly incorporated PC board technology and the use of plugin connectors have made installation and expansion quick and easy. he ADA00 Area of Rescue System provides a solution for security and Rescue Assistance requirements. Reviewing and following the below listed recommendations will result in a trouble free installation and years of dependable service. Unpacking he ADA 00 alarms, indicator lights, and rugged push buttons are set in vandal proof 6 gauge stainless steel for a lifetime of service and lasting appearance. Although the ADA 00 is designed for long life and durability under difficult conditions, it can be damaged during installation. Please use care in unpacking the system components. Equipment cartons damaged during shipping must immediately be reported to the carrier, and also reported to the Manufacturer within days for damage assessment and potential repair Prior to handling any electronic components on cold, dry days, the installer shall discharge any collected static electricity to a known ground, in order to prevent damage to the ADA 00 system logic by a static discharge Avoid touching board components Back Box Flush Back Boxes and installation mounting hardware are ordered from the Manufacturer based on ordering specifications.. x x deep Back Box roughin enclosures for the Master Station ( areas) and s are ordered from the Manufacturer. Master Station Back Boxes for systems larger than s will be custom sized based on system specifications. Contact Manufacturer for rough opening dimensions.. Back Boxes should be mounted solidly in or to the wall using four screws consistent with good engineering practices as established by the EIA and NEC. Refer to ADA requirements for mounting height and placement.. Attach conduit to Back Boxes (one ¾ knockout is provided). Additional holes may need to be center punched and drilled in the back box to receive conduit. Surface Mounting Collar Surface Mounting Collars and installation mounting hardware are ordered from the Manufacturer based on system specifications.. Master Station ( areas) and Surface Mounting Collar dimensions are / x / x deep, with two ¾ knockouts.. Master Station Surface Mounting Collars for systems larger than s will be custom sized based on system specification.. Surface Mounting Collars should be mounted solidly to the wall using four screws consistent with good engineering practices as established by the EIA and NEC. Refer to ADA requirements for mounting height and placement.. Attach conduit to Surface Mounting Collars. Additional holes may need to be center punched and drilled in the Surface Mounting Collar to receive conduit. Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
Master Station. Use the four () manufacturer supplied amper Proof screws to attach the Master Station to the previously installed Back Box or Surface Mounting Collar.. he Master Station shall be located no farther than 00 feet from the Relay Card Cabinet installation.. he Master Station cannot be located within feet of a (Fire Alarm Panel, Annuciator, PBX, ect.). After making all connections to the Master Station as indicated (see Master Station Hook Up Diagram, Appendix Page ) slide the unit onto the Back Box or Surface Mounting Collar and attach with the four () amper Proof screws provided.. Use the four () manufacturer supplied amper Proof screws to attach the to the previously installed Back Box or Surface Mounting Collar.. he shall be located no farther than,000 feet from the Relay Card Cabinet installation.. he cannot be located within feet of a (Fire Alarm Panel, Annuciator, PBX, ect.). After making all connections to the as indicated (see Hook Up Diagram, Appendix Page ) mount the unit onto the Back Box or Surface Mounting Collar and attach with the four () amper Proof screws provided. Relay Card Cabinet. Use four () screws to attach the Relay Card Cabinet to a solid surface in a secure location (typically the electrical or telephone room).. See Relay Card Cabinet Hook Up Diagram, Appendix Page.. he Relay Card Cabinet cannot be located within feet of a (Fire Alarm Panel, Annuciator, PBX, ect.) Battery Backup System Cabinet. Use four () screws to attach the Battery Backup System Cabinet to a solid surface in a secure location (typically the electrical or telephone room).. See Battery Backup Hook Up Diagram, Appendix Page.. he Battery Backup Cabinet cannot be located within feet of a (Fire Alarm Panel, Annuciator, PBX, ect.) Instructional Signs (option)braille Instructional Sign: Use four () amper Proof wood screws provided) to attach each Instructional Sign next to the.illuminated Sign: Use provided universal mounting hardware to locate above each. Housing Devices, Inc. Page 0 www.housingdevices.com Medford, MA 0 Copyright 0000
SYSEM WIRING AND CONNECIONS General HDI suggests on the first powerup, to have zone connected and this is accomplished by removing the gray ribbon cable between the st relay card and the nd relay card in the RELAY CARD CABINE, by doing this the rest of the system area stations are offline.. Install all conduit for the Master Station, s, Relay Card Cabinet, and Battery Backup System Cabinet. Conduit shall also be installed for the power to the Battery Backup System Cabinet. Consult the ADA 00 System Riser Diagram Page for connections.. Make sure wiring shields are connected ONLY at the BAERY BACKUP SYSEM CABINE to prevent Ground Loops. ie all shields to a secure ground (connected to Earth Ground in a manner consistent with safety and code requirements). Master Station Wiring. he Master Station shall be interconnected to each and all other system components in conduit or surface metal raceway where exposed.. he Master Station shall be mounted no CLOSER than F. to other electrical equipment.. Wiring shall be twisted pair # conductor 0AWG with overall shield plus three () additional conductors per each. (See wire and cable legend page #). Part #HDI ADAS. Make sure shields are clipped short and insulated with electrical tape to prevent possible accidental conduction. Consult the Master Station Riser Diagram, Page 0, for proper connections. Wiring. Each shall be interconnected in conduit or surface metal raceway where exposed. Raceways and conduit shall be protected from water and excess moisture.. Conduit placement shall be separate from other circuitry to minimize interference with ADA 00 audio communications (e.g., fluorescent lighting).. Each will be connected with One twisted pair conductor #0AWG with overall shield. Part # HDI ADAS. Make sure shields are clipped short and insulated with electrical tape to prevent possible accidental conduction. Consult the Connection Diagram, Page, for proper connections. Relay Card Cabinet Wiring. he Relay Card Cabinet shall be mounted to a wall with the Control Board in the upper left hand side of the cabinet with the door opening from right to left.. he Relay Card Cabinet shall be interconnected to each system component in conduit or surface metal raceway where exposed. **Wiring shall be twisted pair conductor #0AWG with overall shield. Part # HDI ADAS, Make sure shields are clipped short and insulated with electrical tape to prevent possible accidental conduction. Consult the Relay Card Cabinet Diagram, Page, for proper connections.** Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
Battery Backup System Wiring. he Battery Backup System shall be interconnected to each system component in conduit or surface metal raceway where exposed. (ONLY CONNEC O A DEDICAED AC CIRCUI).. Wiring shall be twisted pair conductor #0AWG with overall shield. Part# HDI ADAS. Make sure wiring shields are connected ONLY at the BAERY BACKUP SYSEM CABINE to prevent Ground Loops. ie all shields to a secure ground clip which is connected to Earth Ground in a manner consistent with safety and code requirements.. Consult the ADA00 Battery Back Up Riser Diagram, Page, for proper connections. Please use care during installation as improper installation may void the warranty. UL Listed Battery Backup. Follow wiring connections in the ACS000 (HDIADABBUUL) manual for 0 AC connections. Please refer to ADA00 Battery Back Up Riser Diagram Page of the wiring section for DC connections. Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
YPICAL ADA 00 hree Zone System HDIADAMS HDIADA00A S NORH Note RESE POWER S SOUH ND FLOOR NORH ND FLOOR ELEV LOBBY PUSH FOR HELP HELP REQUESED HELP COMING Note Note HDIADA00A HDIADARCC0 HELP REQUESED ea. HDIADACB ea. HDIADAARC Note PUSH FOR HELP HELP COMING Note Note HDIADA00A HDIADABBU HELP REQUESED HELP COMING ea. HDIADA ea. HDIADAPS ea. HDICHARGER ea. volt amp/hr battery PUSH FOR HELP Note WIRE & CABLE LEGEND Note Note Note Note Note hree () # AWG wires for 0VAC power from a dedicated emergency power branch circuit. One () conductor UL Listed and Rated ype CMP or FPLP, MultiPair Overall Shielded + Conductor NonShielded Plenum Cable. 0 AWG Pair + Conductor Pair Overall Shielded + Conductor NonShielded Plenum. Part # HDI ADAS One () conductor Part # HDI ADAS, from each HDIADA00A to the HDIADARCC0. One () conductor Part # HDI ADAS, from the HDIADABBU to the HDIADARCC0. hree () #0 AWG conductors from the HDIADARCC0 to the HDI ADAMS for each HDI ADA00A in the system. (For the connection at the HDIADAMS) Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
ROUBLE SHOOING GENERAL HDI suggests on the first powerup, to have zone connected and this is accomplished by removing the gray ribbon cable between the st relay card J and the nd relay card J in the RELAY CARD CABINE, by doing this the rest of the system area stations are offline. Using the ADA 00 System Riser Diagram, see Page, verify that all wiring between each of the ADA 00 Area of Rescue System components has been wired as shown, Power up the System. he System is operating normally when the green LED (on the Master Station) is illuminated and no yellow or red LEDs are illuminated. If the green LED (on the Master Station) is not illuminated, and/or or more yellow or red LEDs are illuminated, then there is a fault in the System. Verify that the System wiring is correct and if there is still a problem, please reference the following problem specific procedures. NOE: When area station is working correctly the common equipment in the system (Battery Backup, ADA, Master Station, Control Board) are working correctly and any other s that aren t working is likely because of incorrect wiring between the Relay Card & the. Basic rouble Shooting Problem Green Power LED is not illuminated Possible Cause & Fixes. Check to see that DC power is present at the Relay Card Cabinet Control Board erminals ( positive) and ( negative). he meter should read vdc to vdc (standard operating power).. Check to see that DC power is present at the Battery Backup System output erminals (+) and (). he meter should read vdc to vdc (standard operating power).. Check to see that DC power is present at the pin Master Station erminals ( positive) and ( negative). he meter should read vdc to vdc (standard operating power). Red LED will not illuminate or stays on constantly Amber ROUBLE LED Is Illuminated See page CONINUED O PAGE CONINUED FROM PAGE. he,, Connector on the back of the Master is loose or wired incorrectly.. he, wires from the relay card could be shorted or wired incorrectly.. Check the ribbon cables on the relay cards.. Visually inspect the pin terminal block at the Master Station,,. he Relay Card Cabinet white terminal block, and () connection for a good electrical connection (confirming continuity) at each location (Master Station, Relay Card Cabinet and ). he wire from the area station should connect straight through to the on the master station. See Master Station Hook Diagram, Appendix Page.. If the amber LED is illuminated and no Area station is used in the system (example. You have a five zone master and only using it as a zone system) Beside the pin terminal block on the Master Station. (,,) the two pin header needs to be shorted, use the small black shunts supplied from the factory included in with the hardware bag.. If the amber LED continues to stay illuminated after completing step call the Manufacturer. Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
Note: his is a common negative ( ) loop used to monitor system rouble (amber LED s on the Master Station) status for breaks in continuity throughout the ADA 00 system. If one or more s break continuity (e.g., bad connection, wire cut, etc.) the amber LED will illuminate for that specific (s) location. Piezo Alarm is not sounding at the Master station. Check to see that DC power is present at the Master Station pin connector by measuring across CB (+) vdc ( ) at the same time. When the system is in alarm. he meter should read vdc to vdc. If voltage is present the Piezo alarm buzzer is defective and contact the factory for a replacement.. If no voltage is present go back to the (Green LED at the Master Station does not illuminate) problem in the troubleshooting guide and follow the instructions to check for the correct voltages.. Put the system in alarm and check to see if the Help Requested LED is illuminated. If it isn t and the Help Coming LED is illuminated check to make sure the Master Station ALK buttons are not depressed or shorted on the PC board side (check for a short between the solder lugs of the talk buttons (ALL HE BUONS SHOULD BE OPEN). Put the system in alarm and check to see if the Help Requested LED is illuminated. If it isn t and the Help Coming LED is Illuminated. Replace the SCR chip at the Relay Card (he SCR chip can be found in the hardware bag included with the system) Please be aware of the position of the SCR before removal. NOE: POWER SYSEM DOWN BEFORE REPLACING SCR BEFORE REPLACING HE SCR PLEASE BE AWARE HE CHIP WAS SHORED OU BY INCORREC OR SHORED WIRING FROM HE AREA SAION O HE RELAY CARD CHECK YOUR WIRING BEFORE POWERING HE SYSEM BACK ON Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
Noise or Feedback. Check (adjust) audio volume control located on the system s ADA amplifier found in the Battery Backup Cabinet.. If the shields are taped at one end & connected to a ground, check the ground for noise, if noise is found disconnect the shields and tape back both ends.. Disconnect the AC from the system and run the system on Battery Backup DC, if the noise goes away you have a dirty AC line or something else is on the circuit. (example: fire alarm panel, access control system, PBX.) NOE: he ADA00 needs a dedicated AC circuit.. Check for installation of AC lines, Fire Alarm Panel, or any other electrical systems that could have a supervision circuit or stray AC running within ft. of the Master Station. Ribbon Cables. he ADA00 relay card cabinet has different kinds of ribbon cables. he ribbon cable that has a twist at one end can only be used when connecting relay cards up and down (VERICAL) from J to J he ribbon cable that has no twists on either end & is a little longer, can only used when connecting relay cards from row to row or (HORIZONAL) from either J to J or J to J erminal Layout See Page In the wiring diagram section Pins: () One side of the switches (+) One side of the switches Help Requested LED (+) Help Coming LED (+) One side of the speaker (+) One side of the speaker () () for all of the components on the area station A short should be read across and at the area station and the relay card cabinet. Pins & at the relay card can be shorted to put the system in alarm. (short out the PFH button any one of the pushbuttons at the area station) Pins & at the relay card and area station should read ohms. (check for ohm at the area station speaker) Pins & on the area station should read the same voltage that is on the Control board & when help requested is lit and the piezo is on. Pins &on the area station should read the same voltage that is on the Control board & when help Coming is lit and the piezo is off. Housing Devices, Inc. Page 6 www.housingdevices.com Medford, MA 0 Copyright 0000
APPENDIX Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
ADA00 System Riser Diagram Zone Master Station Rear Elevation erminal s N.O. Contact White erminal in Relay Card Cabinet Battery BackUp or Amplifier Cabinet erminal VDC CB AUDIO CB SP SP + + Connect 0 Vac to the tri volt step down transformer for battery backup connection Connect Vdc from the Altronix 00 ULX to + and on the terminal block for amplifier cabinet connection 6 Control Board erminal 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal # erminal # erminal # erminal # erminal # erminal Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
ADA00 Relay Card Cabinet Diagram Zone Master Station Rear Elevation erminal s N.O. Contact White erminal in Relay Card Cabinet VDC CB AUDIO CB + 6 Control Board erminal 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal # erminal # erminal # erminal # erminal # erminal Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
ADA00 Master Station Riser Diagram Battery BackUp or Amplifier Cabinet erminal Zone Master Station Rear Elevation erminal s VDC CB AUDIO CB SP SP + + Connect 0 Vac to the tri volt step down transformer for battery backup connection Connect Vdc from the Altronix 00 ULX to + and on the terminal block for amplifier cabinet connection 6 Control Board erminal 6 Relay Card erminal Relay Card erminal N.O. Contact 6 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal White erminal in Relay Card Cabinet # erminal # erminal # erminal # erminal # erminal Housing Devices, Inc. Page 0 www.housingdevices.com Medford, MA 0 Copyright 0000
ADA00 Dual M aster Riser Diagram **O NLY USE DIAG RAM FO R M ULIPLE** LOCAIO N M ASER SAIONS NO E 6 Control Board erminal + VDC CB AUD IO CB Zone M aster Station # Rear Elevation erm inal s NO E + VDC C B AUDIO CB Zone M aster Station # Rear Elevation erm inal s ADA 00 Dual M aster Station W iring Directions. W ire M aster & M aster back to the Relay C ard Cabinet per AD A00 M aster Station Riser Diagram in the wiring section of Installation & O perations M anual.. ALL wiring changes are done at the Relay Card Cabinet NO E Connect erm inal # (CB) at M aster Station to erm inal # ( VDC ) on M aster Station NO E erm inal # (CB) from M aster connects to C ontrol Board erm inal # at the R elay Card C abinet Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
ADA00 Connection Diagram Zone Master Station erminal s White erminal in Relay Card Cabinet 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal # erminal # erminal # erminal # erminal # erminal Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
ADA00 Connection Diagram Zone Master Station erminal s White erminal in Relay Card Cabinet 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal 6 Relay Card erminal # erminal # erminal # erminal # erminal # erminal Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
ADA00 Battery Backup Riser Diagram Zone Master Station Rear Elevation erminal s N.O. Contact VDC CB + 6 Control Board erminal AUDIO CB Battery BackUp or Amplifier Cabinet erminal SP SP + Connect 0 Vac to the tri volt step down transformer for battery backup connection Connect Vdc from the Altronix 00 ULX to + and on the terminal block for amplifier cabinet connection Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
ADA00 MASER ROUBLE LIGH DIRECIONS Installing the shunt Place the shunt supplied in the hardware bag on the JMP header that is not being used for an area station connection in the system. EXAMPLE (a unit system needs the shunts installed on JMP & JMP for the trouble lights to go out on the master station at zones & ) SHUN JMP JMP JMP AREA AREA AREA NOE Shunts are only needed & used for zones that don t have area stations connected to them. JMP JMP AREA AREA Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000
ADA00 Phone Dialer Diagram 6 Control Board erminal located in the relay card cabinet with the K relay installed C C + + IN OU Incoming Phone Line ADA00 Battery BackUp or Amplifier Cabinet erminal SP SP + AD00 Phone Dialer Rear Elevation Please refer to the AD00 Manual supplied with the equipment for programming & additional wiring schematics Housing Devices, Inc. Page 6 www.housingdevices.com Medford, MA 0 Copyright 0000
ADA RM Strobe Connection Diagram ADA00 Strobe Wiring Diagram Using he K Relay for Master Activation ONLY ADA RM Strobe erminal (+) 0 () 6 Control Board with K Relay. Connect terminal (+) at the ADA RM to erminal # at the control board in the Relay Card Cabinet. Connect terminal 0() at the ADA RM to erminal # at the control board in the Relay Card Cabinet. Connect a jumper between erminal # and # at the Control Board ADA00 Strobe Wiring Diagram Using he ADA RM Strobe erminal (+) 0 () # erminal. Connect terminal (+) at the ADA RM to erminal # at the Relay Card in the Relay Card Cabinet. Connect terminal 0() at the ADA RM to erminal # at the Relay Card in the Relay Card Cabinet Housing Devices, Inc. Page www.housingdevices.com Medford, MA 0 Copyright 0000