09/15 nordica 36 ceiling fan model no. 052-1191-4! INSTRUTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS. READ ALL INSTRUTIONS IMPORTANT SAFETY INSTRUTIONS SAVE THESE INSTRUTIONS INSTALLATION AND WIRING TO BE IN AORDANE WITH E, NE, LOAL ELETRIAL ODES and ANSI/NFPA 70. onsult a qualified electrician if you are not familiar with wiring. NOTE: FOR OPTIMUM QUIETNESS, FULLY ASSEMBLE FAN AND RUN 24 HOURS Instruction Manual Model no. 052-1191-4 IMPORTANT: Please read and understand this manual before any assembly. Before beginning assembly of product, make sure all parts are present. ompare parts with packaging contents list.
2 Model no. 052-1191-4 SAFETY PREAUTIONS 1. Turn off power at main electrical service box before starting installation. 2. Electrical connections must comply with local code ordinances or national electrical codes. 3. Make sure the installation site you choose allows the fan blades to rotate freely without any obstructions. 4. When mounting the fan on a ceiling outlet box, use an approved (SA for anada and UL for U.S.) ceiling fan box marked FOR FAN SUPPORT. Ensure the outlet box is securely installed in place such that it is able to support at least the fan weight. 5. WARNING: To reduce the risk of fire, electric shock, or personal injury, mount fan only to an outlet box marked acceptable for fan support and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. onsult a qualified electrician if in doubt. 6.Total fan weight for reference: 36" approximate 6 kg (13 lb 4 oz). SAFETY PREAUTIONS WARNING - To reduce the risk of personal injury DO NOT bend the blade brackets when installing the brackets, balancing the blades or cleaning the fan. Also, DO NOT insert foreign objects in between rotating fan blades. - Mount with the lowest moving parts at least 2.10m (7 ) above floor or grade level. - DO NOT operate reversing switch while fan blades are in motion. Fan must be turned off and rotating blades stopped, reverse china pulled, the speed china pulled again to start in the opposite direction. INSTRUTIONS A ceiling fan has a completely internal switching system for total operation by way of pull chains. On a fan/light combination, three pull chains will exist: One for light, on and off. The second is for fan speeds. This will be marked ( ) on the fan switch housing. 1st pull will give fan High Speed 2nd pull will give fan Medium Speed 3rd pull will give fan Low Speed 4th pull will Shut Fan Off The third pull chain is for Forward/Reverse (Note: Some models come with a slide switch instead of a pull chain). This setting would usually be changed twice per year. Downdraft in summer to create a wind chill to give a cooling effect. Updraft in winter to circulate the hot stratified air off the ceiling and back down to the floor without creating a wind chill. Needed for assembly: Pliers Wrench Wire utters Blade Screwdriver Screwdriver
3 Model no. 052-1191-4 A Mounting Bracket c/w Ground Wire - 1 B Screws & Lock Washers - 4 eiling anopy - 1 D Rubber Bushing - 1 E Lock Pin - 1 F Hemisphere Jam Screw & Hemisphere - 1 G Downrod c/w Ground Wire - 1 H Bolt & otter Pin & Flat Washer - 1 I Motor Assembly - 1 J Upper Jam Screws - 2 K Yoke Screws & Lock Washers - 3 L Motor Screw & Lock Washer - 12 M Blade Bracket - 6 N Blade - 6 Part List O Glass - 1 Q Rubber Ring - 1 P Rubber Gasket - 2 R J-Hook - 1 S Blade Bracket Screws & Flat Washer - 19 T Fibre Washer & Hex Nut - 19
4 Model no. 052-1191-4 eiling Wooden Joist B P A R Approved (SA for anada and UL for U.S.) ceiling fan box (not provided) Outlet Box Screws (not provided) E F F G With Downrod Without Downrod K Q D Assembly Drawing O H I J H S T I O M N T Fig. 1
5 Model no. 052-1191-4 052-2231 NOTE: All set screws must be checked and retightened where necessary, before and after installation. Step 1 - DOWNROD MOUNT - Using a screwdriver, loosen the 2 upper jam screws (J) on the yoke. - Position downrod (G) inside canopy (). - Route wires exiting yoke on motor (I) through downrod (G) and ceiling canopy (). - Position downrod (G)/canopy () into yoke and align holes in yoke and downrod (G). - Insert bolt (H) through hole in yoke and downrod (G). Be careful not to damage or cut the fan wires. - Install flat washer (H) and bolt (H). Secure with cotter pin (H) through hole in the end of the bolt (H). - Secure downrod (G) in position by tightening the 2 upper jam screws (J). J G H Yoke Fig. 2a J H I J AUTION Do not loosen the two lower jam screws Yoke Fig. 2b FLUSH MOUNT Assembly - Remove rubber ring (Q) from canopy (). (See Fig. 2c) - Remove the yoke screws and lock washers (K) which correspond to the holes in the canopy (). - Position canopy () over the holes on motor (I) and secure with the same screws and lock washers (K) removed in the previous step. Be sure to place the rubber bushing (D) between the canopy () and the motor (I). K D Q Fig. 2c I Fig. 2d
6 Model no. 052-1191-4 052-2231 WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to UL/SA listed outlet box marked acceptable for fan support and use mounting screws provided with the outlet box. Step 2 - INSTALL MOUNTING BRAKET - Install J-hook (R) through centre of outlet box and into the wooden joist. - Secure mounting bracket (A) and rubber gaskets (P) to metal outlet box. - Hang the safety cable onto the J-hook (R). - Hang fan on temporary hook and install safety cable. Wood Joist Metal Outlet Box R P A eiling Safety able Temporary Hook Outlet Box Screws (not provided) Fig. 3a Fig. 3b There are several different wiring combinations that can be used to control your ceiling fan depending on your specific requirements. Assembly Step 3 - ONNETING THE (GREEN) GROUND WIRE - onnect ground wire from outlet box to green wire from mounting bracket (A) and downrod using a UL/SA approved marette (not supplied). (Fig. 4a) - onnect ground wire from outlet box to green wire from mounting bracket (A) using a UL/SA approved marette (not supplied). (Fig. 4b) AUTION Green Wire - GROUND Black Wire (Fan) - POWER White Wire (Fan) - OMMON Red or Blue Wire (Light Kit) - POWER
7 Model no. 052-1191-4 052-2231 DOWNROD MOUNT FLUSH MOUNT Ground Wire (Green Wire) Ground Wire (Green Wire) Marette Fig. 4a Marette Fig. 4b NOTE: Once ground wires are connected, carefully tuck wires and marette into the metal outlet box making sure that the wires are clear of the hemisphere and downrod when positioned in mounting bracket (Downrod Mount Only). ONNETING BLAK, WHITE, AND (RED OR BLUE) WIRES - onnect white wire from outlet box to white wire from fan using marette (not supplied). - onnect black wire from outlet box to black wire from fan plus (red or blue wire) using a marette. Black Wire White Wire Assembly NOTE: A red or blue wire would be power for a light kit if applicable. Red or Blue Wire Fig. 5 NOTE: Once wires are connected, carefully tuck wires and marettes into the metal outlet box making sure that the wires are clear of the hemisphere and downrod when positioned in mounting bracket (Downrod Mount Only). Step 4 - MOUNTING FAN ASSEMBLY - Place two screws and lock washers (B) on mounting plate (marked b on Fig. 6a) corresponding to slots in canopy (). Screw in two turns. - Position canopy () against mounting plate aligning slots to screws (marked b on Fig. 6a) then turn to lock. - Position and tighten the two screws and washers (marked a on Fig. 6a) then tighten the two screws (marked b on Fig. 6a).
8 Model no. 052-2231 052-1191-4 Step 5 - ENGAGE HEMISPHERE (Downrod Mount Only) - arefully rotate fan assembly until groove in hemisphere locks over tab of canopy assembly. (Fig. 6b) WARNING: Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard. (b) (a) B (a) (b) Fig. 6a Hemisphere Downrod Groove Fig. 6b NOTE: When installing fan on sloped ceiling, make sure tab on hanger bracket faces towards the top of the slope. Depending on the slope, a longer downrod may be required to prevent fan blades from hitting the ceiling. Step 6 - MOUNT BLADE BRAKETS TO BLADES Assembly - Take out hardware containing blade bracket screws and flat washer (S). S - Place blade bracket screw (S) through flat washer (S), fibre washer (T), hex nut (T) and blade (N). T M - Align with corresponding hole in blade bracket (M). - Repeat with (2) remaining screws and tighten. (Fig. 7) N T Fig. 7
9 Model no. 052-2231 052-1191-4 Step 7 - MOUNTING BLADES TO MOTOR - Take out hardware containing motor screws and lock washers (L). - Position motor screws and lock washer (L) in blade brackets (M), and secure to motor (I). Make sure all screws are tightened securely. Fig. 9a Fig. 9b Step 8 - LIGHT KITS Warning: BE SURE TO TURN OFF POWER BEFORE INSTALLING. - Install proper wattage and type of bulb (not provided) on light kit. - Place glass (O) on light kit and secure with spring clips. Spring clip (See Fig. 10) Fig. 10 O Assembly NOTE: Electrical diagrams are for reference only. Light kits that are not packed with the fan must be SA/UL Listed and marked approval for use with the model fan you are installing. Switches must be SA/UL General Use switches. Refer to the instructions packaged with the light kits and switches for proper assembly. Warning: heck all connections, set screws and screws are securely tightened before the next step.
10 TROUBLE TROUBLESHOOTING SUGGESTIONS 1. Fan will - heck wiring connections to fan. not start - heck fuses and circuit breakers. - heck wiring connections in switch housing. AUTION: Turn power off for last two items. 2. Fan sounds - heck to make sure that all screws in motor housing noisy are snug. - heck to make sure that blade bracket screws are tight. - heck to make sure that marettes in switch housing are not rattling against wall of switch housing. - If fan has a light kit make sure switch housing screws and set screws are tight. - Some fan motors are sensitive to signals from solid state variable controls. If solid state controller is used, change to an alternative control. - Allow a 24-hour break-in period to eliminate most noises. 3. Fan wobbles - heck that all blades are screwed firmly into blade or shakes brackets. excessively. - heck that blade brackets are secured firmly to motor. - heck distance from tip of blades to ceiling. Gently bend up or down the blade brackets until all distances are the same. - heck distance between blade tip to blade tip. All measurements should be equal. Loosen blade screws and position blade until even then retighten. - heck that the downrod hemisphere notch is engaged in canopy. - heck to make sure that jam screws in downrod are tightened. - Make sure canopy and mounting bracket are tightened securely to wooden joist. - Make sure warpage has not occurred in wooden blades. Troubleshooting This For Living product carries a five (5) year warranty against defects in workmanship and materials. Trileaf Distribution agrees to replace the defective product free of charge within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Warranty Imported by: Trileaf Distribution Trifeuil Toronto, anada M4S 2B8