aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Smart Cycle Plus Cycling Refrigerated Air Dryers (1200-3000 scfm) Magnum Series Cycling Refrigerated Air Dryers (4000-15000 scfm)
02 08 Cycling Refrigerated Air Dryers Smart Cycle Plus (SCP) and Magnum Series The importance of compressed air as a provider of energy for modern industrial processes is widely known. What is often overlooked however is the need to provide quality treatment for this air. In fact, the air entering the system contains condensate which, when cooled, will turn into liquid water, causing extensive damage not only to the compressed air network, but also to the finished product. These costly contamination problems can be avoided by installing a Smart Cycle Plus or Magnum Cycling Refrigerated Air Dryer package complete with Parker Airtek filtration. A refrigerated dryer is typically selected to achieve its design performance at the user s most extreme working conditions. (ie. a warm summer day with the air compressor operating at maximum load). compressor load will vary significantly during a working day and will rarely be at full load, thereby significantly reducing the load on the dryer itself. Furthermore, average temperatures are well below the maximum inlet and ambient temperatures for which the system has been sized. Reduced temperatures at colder moments during the day and overall temperature reductions during the midseason and winter add a further reduction to the load on the dryer. Smart Cycle Plus and Magnum perfectly and continuously adapt to the actual operating conditions, ensuring dewpoint control together with the lowest operating costs. Over and above this extreme flexibility of use, Smart Cycle Plus and Magnum s advanced technical solutions offer reliability, efficiency, and energy savings, making it the ideal solution for all industrial users. This maximum condition, however, is very rarely achieved in everyday conditions. First, the air Benefits: Optimum dewpoint levels for highest system performance Lowest operating costs Continuously and automatically adjusts to actual working parameters High reliability, easy to use and maintain Integral level actuated energy saving drain SCP1200 Low pressure drop design Microprocessor based energy management controller Flood level control protects refrigerant circuit Tube & shell heat exchanger MSC6000
SETTINGS READ RUN SELECT ALARM 100% 75% 50% 25% DRAIN <10% LOAD OVER LOAD Smart Cycle Plus - How it works The Next Generation - Full cycling mode results in dryer air than conventional dryers The Smart Cycle Plus configuration combines the advantages of superior performance and energy savings with the oil removal efficiency of a built-in, multi-stage separator/cold coalescer. Dry Air Out By locating the coalescing filter at the coldest point in the air system, filtration efficiency is greatly enhanced, and because of a pre-separation of bulk contaminants prior to entering the element(s), pressure drop and operating costs are dramatically reduced. Pre-Cooler/Re-Heater Wet Air In Cold Coalescer Flooded Shell Evaporator Separator Static Cooler Tri Mode Controller LOAD/UNLOAD MODE DEW POINT 34 F Thermal Expansion Valve Flood Level Control Condenser Check Valve Suction Accumulator Liquid Receiver Refrigerant Compressor Unloader Valve Warm Wet Air Partially Cooled Air Cold Wet Air Dry Purified Air Liquid Refrigerant Cold Refrigerant Gas Hot Refrigerant Gas
04 08 Smart Cycle Plus - Features Best in class dewpoint performance Tri Mode Operation allows dryer to operate in cycling, non-cycling or auto mode. Unlimited cycling due to unloaded soft start Multi-stage separation and filtration Level actuated drain Diagnostic readouts indicate need for service Drain light Alarm light Displays in English or Metric Serial Port with MODBUS Digital readout air in temperature Digital readout ambient or water in temperature High inlet temperature warning High ambient or water in temperature warning Optional Control Center Benefits Lower dewpoint temperature achieved with Smart Cycle Plus results in cleaner operation Longer lasting components Upstream malfunction that results in more severe inlet conditions can be readily handled without resulting in downstream problems Lower operating costs, with no sacrifice in performance Dryer runs only as needed Environmentally friendly refrigerant Tube and shell heat exchanger with grooved tube sheets provide greatest mechanical strength and lowest pressure drop Patented flood level control protects refrigeration circuit Tube and Shell Heat Exchanger Grooved Tubesheets
Magnum Series - How it works Parker Airtek s demand control with cylinder head unloading reduces energy consumption and maintains a true and constant dewpoint by turning the refrigeration compressor on or off in direct response to the actual dewpoint temperature of the compressed air. Air Circuit Saturated compressed air enters the tubes at the air to air heat exchanger [1] where it is precooled by the cold compressed air returning through the shell from the evaporator. After the compressed air has been precooled, it flows into the evaporator tubes [2] where the temperature is lowered to approximately 34 F (1.1 C). The temperature reduction forces water and oil vapors to condense. The mixture of cold compressed air and condensed liquid flows into the mechanical moisture separator [3] where the liquids are removed by impingement and centrifugal action. The compressed air then flows from the first stage moisture separator up through the second stage 3 micron filter element where it s further purified. The purified compressed air returns through the shell side of the air to air heat exchanger [4] where its volume is increased through reheating. The processed compressed air then enters the main distribution system [5] as a dry, clean and efficient utility. Refrigeration Circuit Parker Airtek s refrigeration system enables the use of a fully active flooded evaporator [2]. Compressed air flows through the submerged tubes in the flooded shell to ensure dewpoint integrity [6]. If any liquid refrigerant were present in the suction line, it would flash off to a vapor. An air temperature probe in the evaporator s air side tubing, reads the temperature and displays it on the control center panel [7]. When the air temperature reaches its low set point, the compressor will either shut off, or unload, saving energy during periods of low load. When the dewpoint setting is reached, the compressor [8] will resume normal operation. When operating in the cycling mode, a virtually unlimited number of stops and starts is made possible by opening the unloader valve [9] prior to starting the compressor. This allows an unloaded start each time the compressor comes on. When operating in the load/ unload mode, the warm refrigerant gas bypasses the condenser [10] and expansion valve [11], and flows through the static cooler [12]. This core of cold liquid refrigerant removes the heat from the discharge gas to prevent a high suction temperature as the gas returns to the inlet side of the compressor. [5] Dry Air Out [4] Pre-Cooler/Re-Heater [1] Wet Air In Cold Coalescer Surge Tank [3] [2] Separator [12] Static Cooler [7] Suction Solenoid Valve VSD [6] Flood Level Control Level Master Expansion [11] Valve Liquid Line Solenoid Liquid Line Dryer [10] Liquid Receiver water in water out Check Valve Suction Accumulator [8] Semi-Hermetic Compressor Unloader Valve [9] Condenser
06 08 Magnum Series - Features Thermal Bank System Flood Level Control High Efficiency Tube and Shell Heat Exchangers Grooved Tube Sheets Reliable Demand Drain Remote Air Cooled Available Superheated Cool Dry Gas Hot Gas From Compressor Flood Level Control Hot Gas To Condenser Tube and Shell Heat Exchanger Grooved Tubesheets Demand Drain Benefits Thermal Bank System delivers cleaner and drier compressed air Easily serviced main heat exchanger Precise timing and programming, no freeze-up conditions Improved performance (2X main evaporator surface area) Simple, reliable, and non-fouling Leak-proof joints Greater mechanical strength and precision milled grooves in tube sheets
Engineering Specifications MEMBER OF Performance Data Model Air Connections Nominal Capacity (scfm)* Dimension ins (mm) Weight H W D lbs kg Primary Voltages Replacement Separator Element Recommended Pre-Filter Recommended After-Filter SCP1200 3" Flg 1250 65 (1651) 74 (1880) 41 (1041) 1850 839 460V/3Ph/60Hz JE1600-C10 JL1250-C JL1250-F SCP1500 4" Flg 1600 72 (1829) 78 (1981) 48 (1219) 2200 998 460V/3Ph/60Hz JE1600-C10 JL1600-C JL1600-F SCP2000 6" Flg 2050 76 (1930) 102 (2591) 54 (1372) 3000 1361 460V/3Ph/60Hz (3) JE1000-C10 JL2000-C JL2000-F SCP2500 6" Flg 2500 76 (1372) 102 (2591) 54 (1372) 3370 1529 460V/3Ph/60Hz (3) JE1000-C10 JL2600-C JL2600-F SCP3000 6" Flg 3000 85 (2159) 108 (2743) 66 (1676) 4015 1821 460V/3Ph/60Hz JE3000-C10 JL3000-C JL3000-F *Flow rates at the following climatic conditions - Ambient Temperature: 100 F (38 C), Inlet Temperature: 100 F (38 C), Inlet Pressure: 100 psi g (7 bar g). Air-cooled & water-cooled available (SCP1200-SCP3000) Model Air Connections Nominal Capacity (scfm)* Dimension ins (mm) Weight H W D lbs kg Primary Voltages Replacement Separator Element (Qty) MSC4000 8" Flg 4000 95 (2413) 108 (2743) 68 (1727) 5680 2576 460V/3Ph/60Hz (2) JE-C1600-30 MSC5000 8" Flg 5000 95 (2413) 108 (2743) 68 (1727) 6415 2910 460V/3Ph/60Hz (2) JE-C1600-30 MSC6000 8" Flg 6000 95 (2413) 146 (3708) 76 (1930) 7725 3504 460V/3Ph/60Hz (3) JE-C1600-30 MSC8000 10" Flg 8000 95 (2413) 146 (3708) 76 (1930) 9610 4359 460V/3Ph/60Hz (4) JE-C1600-30 MSC10000 10" Flg 10000 95 (2413) 161 (4089) 83 (2108) 11020 4999 460V/3Ph/60Hz (3) JE-C2000-30 MSC12500 12" Flg 12500 111 (2819) 160 (4064) 94 (2388) 13250 6010 460V/3Ph/60Hz (4) JE-C2000-30 MSC15000 12" Flg 15000 120 (3048) 150 (3810) 100 (2540) 14600 6623 460V/3Ph/60Hz (3) JE-C3000-30 Notes: (1) Cold Coalescing Element Standard (2) Pressure dewpoint is based on CAGI ADF 100 Standard for rating and testing compressed air dryers. 100 psi g (7 bar g) inlet air pressure, 100 F (38 C) inlet air temperature, 100 F (38 C) ambient temperature. (3) Larger Sizes Available - Consult Factory (4) Dryer needs to be fully protected from nature s elements (i.e. rain, wind, snow, etc.) Technical Data Dryer Models Max Inlet Pressure Max Inlet Temperature Max Ambient Temperature Min Ambient Temperature psi g bar g F C F C F C Refrigerant SCP1200 - SCP1500 200 13.7 131 55 115 46 41 5 R404A SCP2000 - SCP3000 150 10.3 131 55 115 46 41 5 R404A MSC4000 - MSC6000 150 10.3 131 55 115 46 41 5 R404A Correction Factors To obtain dryer capacity at new conditions, multiply nominal capacity x C1 x C2 x C3. F 80 90 95 100 105 110 115 Ambient Temperature (C1) C 27 32 35 38 41 43 46 CF 1.12 1.08 1.05 1.00 0.95 0.90 0.84 F 80 85 90 95 100 105 110 115 120 130 Inlet Temperature (C2) C 27 29 32 35 38 41 43 46 49 54 CF 1.22 1.22 1.22 1.10 1.00 0.92 0.83 0.76 0.69 0.56 psi g 50 60 75 80 90 100 110 125 130 140 150 Working Pressure (C3) bar g 3.5 4.1 5.2 5.5 6.2 6.9 7.6 8.6 9.0 9.7 10.3 CFP 0.80 0.84 0.90 0.92 0.96 1.00 1.01 1.02 1.03 1.04 1.05
Worldwide Filtration Manufacturing Locations North America Compressed Air Treatment Filtration & Separation/Balston Haverhill, MA 978 858 0505 www.parker.com/balston Finite Airtek Filtration Airtek/domnick hunter/zander Lancaster, NY 716 686 6400 Finite Airtek Filtration/Finite Oxford, MI 248 628 6400 www.parker.com/finitefilter Engine Filtration & Water Purification Racor Modesto, CA 209 521 7860 www.parker.com/racor Holly Springs, MS 662 252 2656 www.parker.com/racor Beaufort, SC 843 846 3200 www.parker.com/racor Racor Village Marine Tec. Gardena, CA 310 516 9911 desalination.parker.com Parker Sea Recovery Carson, CA 310 637 3400 www.searecovery.com Hydraulic Filtration Hydraulic Filter Metamora, OH 419 644 4311 www.parker.com/hydraulicfilter Laval, QC Canada 450 629 9594 www.parkerfarr.com Process Filtration domnick hunter Process Filtration Oxnard, CA 805 604 3400 www.parker.com/processfiltration Madison, WI 608 824 0500 www.scilog.com Phoenixville, PA 610 933 1600 www.parker.com/processfiltration Aerospace Filtration Velcon Filtration Colorado Springs, CO 719 531 5855 www.velcon.com Europe Compressed Air Treatment domnick hunter Filtration & Separation Gateshead, England +44 (0) 191 402 9000 www.parker.com/dhfns Parker Gas Separations Etten-Leur, Netherlands +31 76 508 5300 www.parker.com/dhfns Hiross Zander Padova Business Unit Padova, Italy +39 049 9712 111 www.parker.com/hzd Hiross Zander Essen Business Unit Essen, Germany +49 2054 9340 www.parker.com/hzd Engine Filtration & Water Purification Racor Dewsbury, England +44 (0) 1924 487 000 www.parker.com/rfde Racor Research & Development Stuttgart, Germany +49 (0)711 7071 290-10 www.parker.com/rfde Hydraulic Filtration Hydraulic Filter Arnhem, Holland +31 26 3760376 www.parker.com/hfde Urjala Operation Urjala, Finland +358 20 753 2500 www.parker.com/hfde Condition Monitoring Centre Norfolk, England +44 (0) 1842 763 299 www.parker.com/hfde Parker Kittiwake West Sussex, England +44 (0) 1903 731 470 www.kittiwake.com Parker Procal Peterborough, England +44 (0) 1733 232 495 www.kittiwake.com Process Filtration domnick hunter Process Filtration Birtley, England +44 (0) 191 410 5121 www.parker.com/processfiltration Parker Twin Filter BV Zaandam, Netherlands +31(0)75 655 50 00 www.twinfilter.com Asia Pacific Australia Castle Hill, Australia +61 2 9634 7777 www.parker.com/australia China Shanghai, China +86 21 5031 2525 www.parker.com/china India Navi Mumbai, India +91 22 651 370 8185 www.parker.com/india Parker Fowler Bangalore, India +91 80 2783 6794 www.johnfowlerindia.com Japan Tokyo, Japan +81 45 870 1522 www.parker.com/japan Parker Techno Osaka, Japan +81 66 340 1600 www.techno.taiyo-ltd.co.jp Korea Hwaseon-City +82 31 359 0852 www.parker.com/korea Singapore Jurong Town, Singapore +65 6887 6300 www.parker.com/singapore Thailand Bangkok, Thailand +66 2186 7000 www.parker.com/thailand Latin America Parker Comercio Ltda. Filtration Division Sao Paulo, Brazil +55 12 4009 3500 www.parker.com/br Pan American Division Miami, FL 305 470 8800 www.parker.com/panam Africa Aeroport Kempton Park, South Africa +27 11 9610700 www.parker.com/africa 2013 Parker Hannifin Corporation. Product names are trademarks or registered trademarks of their respective companies Catalog: SCP and Magnum Rev 003 NA 08/2013 Parker Hannifin Corporation Finite Airtek Filtration Division 4087 Walden Avenue Lancaster, NY 14086 phone 716 686 6400