ASYSTAT65A Humidity Control INSTALLE S GUIDE APPLICATION Humidity Control The humidity control provides automatic low voltage control of humidifiers in central heating and cooling equipment for both humidification and dehumidification applications. See Fig.. It has an spst, snap-acting, dust-proof switch that opens when humidity rises above the control setting. It is designed for wall or surface duct mounting. INSTALLATION When Installing this Product.... ead these instructions carefully. Failure to follow them could damage the product or cause a hazardous condition.. Check the ratings given in the instructions and on the product to make sure the product is suitable for your application. 3. Installer must be a trained, experienced service technician. 4. After installation is complete, check out product operation as provided in these instructions. CAUTION Personal Injury Hazard. Power supply can cause electrical shock. Disconnect power supply before beginning installation. Location and Mounting A mounting template is included for mounting the humidity control next to your thermostat. See Fig.. However, the humidity control can be mounted in any other convenient location in the living area or equipment room. NOTE: The humidity control electrical connections are not shared with the thermostat. Wall Mounting HOLE FO WIING THE DUCT MOUNTING INSTALLATIONS CASE EMOVAL SLOT M9844 Fig.. Humidity control. Mount the control in an area with average room temperature and average relative humidity. Select a location for mounting the humidity control:. Hold the mounting template (included) next to your thermostat. Select the mounting side for the humidity control. The template is reversible for mounting on either the left or right side of the humidity control. See Fig... Mark the holes for the two mounting screws (included). Then mark the hole for the low voltage wiring on the template that corresponds with the side selected in step. 3. emove the template and drill the holes. 4. un low voltage wiring to the location and pull about 6 in. (5 mm) of wire through the hole. 5. Plug hole with nonflammable insulation to prevent drafts from affecting the control operation. 6. emove the humidity control case from the base. See Fig.. 7. Position the base on the wall with the arrow up. 8. Use the two in. (5 mm) mounting screws to secure the base to the wall. Pub. No.: -5034-0 U.S. egistered Trademark Copyright 003 All ights eserved 69-699
THEMOSTAT WALLPLATE MOUNTING TEMPLATE ETUN AI ALTENATE LOCATION ETUN AI WIING HOLES FO MOUNTING ON IGHT. USE LEFT HOLES FO MOUNTING ON LEFT. MOUNTING HOLES () M9830 6 in. (5 mm) MINIMUM BEST LOCATION 5 in. (38 mm) MINIMUM Fig.. Positioning mounting template. Use 8- to -gauge wire for proper wiring. 9. Connect the low voltage wires to the leads on the humidity control. 0. eplace the humidity control case. Duct Mounting When mounting near an elbow area, locate the control 6 in. (5 mm) upstream from the elbow so the element is exposed to the normal airflow (Fig. 3). ETUN AI DUCT M3369 Fig. 3. Selecting duct location for control.. Locate the control at least 8 in. (03 mm) upstream from the humidifier in the return air duct. See Fig. 3.. Apply the duct template to the duct location. 3. Use the duct template, Fig. 4, to make the opening and mounting holes for the humidity control. 4. emove the humidity control case from the base. See Fig.. 5. Position the foam gasket on the humidity control base. 6. Position the base on the duct with the arrow up. 7. Use the four in. (5 mm) mounting screws to secure the base to the duct. 8. Connect the low voltage wires to the leads on the humidity control. 9. eplace the humidity control case. Use 8- to -gauge wire for correct wiring. 4X DILL 7/64 IN. DIAMETE PECE 4 X 7/64 PO. DUCT TEMPLATE GABAIT DE GAINE CAUTION Equipment Damage Hazard. Be careful when selecting control location and cutting hole in ductwork. Do not cut or drill into air conditioning or electrical accessories. Do not install control on supply (hot air) ductwork. To use template:. emove backing and apply template to duct.. Cut along template dotted line and drill the mounting holes. MISE EN GADE isque d'endommager le matériel. Faire attention au moment de choisir l'emplacement du régulateur et de percer les trous dans la gaine. Ne pas couper ou percer les accessoires électriques ou de climatisation. Ne pas installer le régulateur sur la gaine d'alimentation (air chaud). Utilisation du gabarit:. etirer l'endos du gabarit et placer le gabarit sur la gaine.. Couper le long de la ligne pointillée du gabarit et percer les trous de fixation. M3373 Fig. 4. Positioning return air duct template. Pub.No.: -5034-0 69-698
HEATING CYCLE HUMIDITY CONTOL WIING WATE SOLENOID LEAD WIE CAUTION Personal Injury Hazard. Power supply can cause electrical shock and injury. Disconnect power supply before installation or servicing. All wiring must comply with applicable local codes, ordinances and regulations. Make wiring connections according to humidifier instructions, if available; otherwise, see typical wiring diagrams in Fig. 5 through 9. Select models of fan centers include humidifer taps so the current sensing relay or sail switch is not needed. If not using a current sensing relay or sail switch, the humidifier must be energized during blower motor cycles for proper operation. On multispeed blower applications, do not wire the high voltage side of the transformer to the same power source that services the furnace blower. Premature transformer burnout can occur. TANSFOME CUENT SENSING ELAY 4V WIING. Fig. 7. Typical wiring diagram of current sensing relay with humidifier. L L (HOT) POWE SUPPLY. POVIDE DISCONNECT MEANS AND OVELOAD POTECTION AS EQUIED. SAIL SWITCH LO C HI TANSFOME 4V WIING. L L (HOT) M9833 POWE SUPPLY. POVIDE DISCONNECT MEANS AND OVELOAD POTECTION AS EQUIED. M9834 L (HOT) POWE SUPPLY L FAN CONTOL FUNACE FAN MOTO TANSFOME POVIDE DISCONNECT MEANS AND OVELOAD POTECTION AS EQUIED. 4 VAC WIING. M983 Fig. 5. Typical wiring diagram for system with fan interlock. Fig. 8. Typical wiring diagram of sail switch with humidifier. FAN WIING TEMINALS TEMINALS TO SYSTEM FAN 4V WIING. NOTE: FOLLOW THE INSTALLATION INSTUCTIONS INCLUDED WITH THE STEAM TO WIE THE SYSTEM FAN. M9835 Fig. 9. Typical wiring diagram for steam humidifiers. L (HOT) L POWE SUPPLY FAN CONTOL DPST SWITCHING ELAY TANSFOME H C L -SPEED FAN MOTO POWE SUPPLY. POVIDE DISCONNECT MEANS AND OVELOAD POTECTION AS EQUIED. M983 4 VAC WIING. Fig. 6. Typical wiring diagram for system with -speed fan motor. Pub.No.:-5034-0 3 69-699
HEATING CYCLE HUMIDITY CONTOL ADJUSTMENTS Humidity Control Adjustment To maintain optimum humidity control without causing condensation on cold surfaces such as windows, the homeowner must adjust the setpoint as the outdoor temperature changes. To reduce relative humidity, reduce the setpoint approximately 3% H humidity every 4 hours. To increase relative humidity, increase the setpoint approximately 3% H every 4 hours. Setpoint Adjustment Set the humidity setpoint according to the prevailing outdoor temperature. See Table for recommended settings. Table. ecommended Humidity Control Setting. Outdoor Temperature ecommended F C Humidity Control Setting -0-9 5-0 -3 0 0-8 5 +0-30 +0-7 35 >+0 >-7 40 Pub.No.: -5034-0 69-698 4
COOLING CYCLE HUMIDITY CONTOL WIING See Fig. 0 and for air handler and furnace wiring for cooling cycle humidity control. THEMOSTAT 8 T VAIABLE SPEED AI HANDLE T HEAT PUMP O.D. SECTION (SINGLE SPEED) T CAUTION Personal Injury Hazard. Power supply can cause electrical shock and injury. Disconnect power supply before installation or servicing. All wiring must comply with applicable local codes, ordinances and regulations. Make wiring connections according to humidifier instructions, if available; otherwise, see typical wiring diagrams in Fig. 9 and 0. COOLING CYCLE HUMIDITY CONTOL ADJUSTMENTS It is desirable to maintain the humidity in the living space at the humidification comfort range of 5 to 50 percent relative humidity. To reduce the relative humidity, position the arrow on the humidity control to the humidity control setting: 40 setting controls to 40+/-0% H. 50 setting controls to 50+/-0% H. When activated, the humidity control lowers the furnace/air handler blower speed, reducing air velocity over the furnace/air handler coil and removing a geater amount of moisture from the air. O Y G W X U B F INTE-COMPONENT WIING Y/Y W 3 4 W 7 SUPPL. HT. CONTOL BOX TO POWE SUPPLY PE LOCAL CODES AND AS DEFINED IN FIELD WIING TABLE O YI/YLo G W3 4 V FACTOY WIING LINE V B 5 ODT B/X O LOW VOLTAGE WIING TO BE NO. 8 A.W.G. MINIMUM CONDUCTO. WHEN HEATES AE USED, DISCAD POWE LEADS WITH POLAIZED PLUG PM-A AND CONNECT -PF TO MATING PLUG IN THE HEATE CONTOL BOX AS SHOWN. 3 TEMINALS W WILL HAVE INTENAL CONNECTIONS ONLY IF ND CONTACTO IS USED BY THE HEATE FO CONTOLLING POWE TO ELECTIC HEATING ELEMENTS. IF ND (BH) CONTACTO IS NOT USED, THEN FIELD CONNECTIONS TO W CAN BE OMITTED AS APPOPIATE. 4 IF ODT IS NOT USED, THEN CONNECT APPOPIATE JUMPE FOM W TO W TO W3 ON LVTB. 5 IF IS NOT USED, CONNECT JUMPE FOM "" TO "" FO FULL TONNAGE AIFLOW IN COOLING. 6 CONNECT IN THIS MANNE IF O.D. UNIT HAS "F" CONNECTION. 7 CONNECT W3 TO W ONLY IF USING HEATE WITH 3 HEATE STAGES. 8 SEE HEATE WIING DIAGAM FO HEATING ANTICIPATO SETTING. M985 6 4 V LINE V FIELD WIING O Y B F Fig. 0. Wiring for variable-speed air handler. Pub.No.:-5034-0 5 69-699
THEMOSTAT FIELD WIING DIAGAM FO VAIABLE SPEED STAGE FUNACE STAGE HEATING, STAGE COOLING USING A STAGE HEATING, STAGE COOLING THEMOSTAT (OUTDOO SECTION WITHOUT TANSFOME) VAIABLE SPEED -STAGE FUNACE GOUND SCEW FUNACE JUNCTION BOX O YI/YLo 7 Y Y Y/Y W4 JUMPE 9 TO 5 V PH., 60 HZ., POWE SUPPLY PE LOCAL CODES 5 HUM 5 EAC WH WH LH LN WH/ /3 / B G W G W FIELD ADDED JUMPE W TO W ND STAGE WILL FIE 0 MINUTES AFTE ST. W INTE-COMPONENT WIING B/C 6 B/C 4 V LINE V FIELD WIING 4 V LINE V FACTOY WIING BE SUE POWE AGEES WITH EQUIPMENT NAMEPLATE(S). LOW VOLTAGE (4 V WIING) TO BE NO. 8 A.W.G. MINIMUM. 3 GOUNDING OF EQUIPMENT MUST COMPLY WITH LOCAL CODES. 4 SET THEMOSTAT HEAT ANTICIPATO PE UNIT WIING DIAGAM. 5 THESE LEADS POVIDE 5 V POWE FO CONNECTION OF ELECTONIC AI CLEANE AND MAXIMUM LOAD.0 AMPS EACH. 6 THIS WIE IS ONLY FO THEMOSTATS EQUIING CONNECTION TO TANSFOME COMMON TEMINAL. 7 THE "Y" TEMINAL FOM THE THEMOSTAT MST BE WIED TO THE "Y" TEMINAL OF THE FUNACE CONTOL FO POPE BLOWE OPEATION DUING COOLING. 8 SET DIP SWITCHES WITH POWE OFF PE INSTALLATION INSTUCTIONS TO SET AIFLOW AND INDOO FAN OFF DELAYS. 9 OPTIONAL HUMIDITY CONTOL IS TO BE CONNECTED BETWEEN AND. FACTOY INSTALLED JUMPE TO ON THE CICUIT BOAD MUST BE CUT IF OPTIONAL IS USED. THE JUMPE MUST ALSO BE CUT WHEN APPLYING AN AIFLOW COMMAND SIGNAL TO THE INPUT SUCH AS WITH THE VAIABLE SPEED, SINGLE-ZONE COMMAND SIGNAL TO THE INPUT SUCH AS WITH VAIABLE SPEED, SINGLE-ZONE AND MULTI-ZONE SYSTEM CONTOLLES. ON SINGLE SPEED COOLING, ONLY/NON-HEAT PUMP. FO TWO COMPESSO O TWO SPEED SYSTEMS, JUMPE YLo TO O M9853 Fig.. Wiring for variable-speed, -stage furnace (H/C) using H/C thermostat. OPEATION AND CHECKOUT Place the system in operation and observe through at least one complete cycle to make certain that all components are functioning correctly. Pub.No.: -5034-0 69-698 6
Pub.No.:-5034-0 7 69-699
Pub.No.: -5034-0 American Standard Inc. 600 Troup Highway Tyler, TX 757-900 69-699 G.H. -03 For more information, contact your local Dealer (Distributor).