p. 1 Product Catalogue v16.1 Boiling and Chilled Water Water Heating Hand Dryers Space Heating

p. 1 Product Catalogue v16.1 Boiling and Chilled Water Water Heating Hand Dryers Space Heating

p. 2

Introduction Hyco has been established for over 25 years and is a leading player in the UK electric water heating market as well as specialising in hand dryers and space heating. We are a manufacturer and distributor to many of the UK s leading electrical wholesalers and plumbers merchants. Quality and Innovation The new Zen Boiling and Chilled Tap range, the Zen Font and the Omega Wall Mounted Boiling Water Heater demonstrate Hyco s commitment to quality products, energy efficiency, continuous innovation and UK based design and assembly. p. 3 Specification Hyco has a specification team working nationally with architects, mechanical and electrical consulting engineers and contractors to ensure the correct product is selected right from the project design stage. Customer Service Hyco is committed to customer satisfaction and our sales and technical teams are always on hand to offer advice and support on any issue from installation to arranging delivery of urgent orders direct to site to arrive at the start of the next working day. Technical Support Hyco provides comprehensive pre and post sales technical support to end users, installers, architects and distributors. Our Technical Sales team will help ensure that customers get the right product every time. Stock Availability We have high stock availability and offer free next day delivery on most orders.

Contents Boiling and Chilled Water Zen Boiling and Chilled Tap Range Zen Solo Boiling Water Tap Zen Spa 2 in 1 Boiling and Chilled Tap Zen Life 3 in 1 Boiling Tap with Hot and Cold Mixer Zen Ice 2 in 1 Cold Drinks Station Zen Font with Drain Omega Wall Mounted Boiling Water Heater Microboil Wall Mounted Boiling Water Heater Sapphire Stainless Steel Water Cooler Floor Standing Sapphire Water Cooler Floor Standing Hot and Cold Drinking Water Filters 8-11 12 14 16 18 20 22 24 26 28 30 p. 4 Water Heating Energy Related Products (ErP) Ratings Speedflow Unvented Undersink 5 15 litre Speedflow Accessories Powerflow Unvented Multipoint 30 90 litre Thermostatic Mixing Valve Everlast Unvented 90 600 litre Rho Instantaneous 4.4 and 6.0 kw Aquila Instantaneous 9.6 kw Instantaneous Performance Charts Taps: Non-Concussive, Mixer, Infrared Wave Instantaneous Handwash, Manual and Automatic Handyflow Oversink Vented 5 litre Handyflow Undersink Vented 5 litre 33 34 36 38 40 42 44 46 48 50 52 54 56 Hand Dryers and Hair Dryers Jetstream Blade Jetstream Ellipse Jetstream Curve Jetstream Slimline Jetstream Arc Tornado Cyclone Hurricane 60 62 64 66 68 70 72 74

Topaz Digital Hair Dryer Opal Holster Style Hair Dryer Jade Traditional Hair Dryer 76 78 80 Space Heating Fixed Heating Accona Panel Heater Scirocco Convector Heater Maestro Air Curtain Novara PTC High Level Heater Mistral Bathroom Fan Heater Zephyr Downflow Fan Heater High Level Arezzo Downflow Fan Heater Low Level 84 86 88 90 92 94 96 Portable Heating p. 5 Aztec Industrial Fan Heater Fiji Fan Heater Riviera Oil Filled Radiator 98 100 102 Frost Protection Sahara Tubular Heaters Sahara Tubular Heater Guards Mojave Frost Protector 400 W Inca Frost Protector 200 W 104 106 108 110 Towel Rails Alize S Shape Aquilo Ladder Style 112 114 Quartz Infrared Sun Prince Indoor Halogen Quartz Controller Sun King Outdoor Halogen 116 118 120

p. 6

Product Category Boiling and Chilled Wat e r p. 7

Boiling and Chilled Water Zen Boiling and Chilled Tap Range p. 8 Usage The Zen Boiling and Chilled Tap Range delivers elegant practical solutions for your domestic or commercial kitchen, providing tailored combinations of boiling water for tea and coffee making, high quality cold drinking water and kitchen hot and cold mixer tap capabilities. 100 C or 98 C Filtered Cold Hot & Cold Mixer Filtered Chilled Sparkling Boiling and Chilled Tap Options Product codes in the table are for Zen taps with 3 litre boiling water tank. For 6 litre tank models replace 3L with 6L in the product code. Product Product Code Boiling Water Temperature ( C) Filtered Cold (Ambient) Filtered Chilled* Hot & Cold Mixer Zen Solo SOLO3L100 SOLO3L98 100 98 Zen Spa SPA3L100 SPA3L98 SPA3L100C SPA3L98C 100 98 100 98 Yes Yes Yes Yes Zen Life LIFE3L100 LIFE3L98 100 98 Yes Yes Zen Ice ICESOLO ICESOLOC ICESPAC Yes Yes Yes Yes *Upgrade to sparkling on any of the filtered chilled Zen Spa or Zen Ice models

Boiling and Chilled Water Zen Boiling Range Features and Benefits Energy Efficiency One of the most energy efficient boiling water taps available. Innovative aerogel insulation around the boiling water tank keeps energy losses to a minimum. The Zen tap with 3 litre boiling water tank has energy losses of 15 W (0.36 kwh/day) for the 98 C models and 17 W (0.42 kwh/day) for the 100 C models. Smart Technology Algorithms learn and predict boiling water usage. On when you need it, off when you don t, increasing energy efficiency. Ready Profile User Profile p. 9 12am 6am 12pm 6pm 12am Tank Capacity The capacity of the boiling water tank is 3 litres as standard or 2 x 3 litre tanks to provide 6 litre capacity. Safety Features Safety lock mechanism on boiling side. Cool touch insulated tap. Designed and assembled in the UK At our head office in West Yorkshire. Warranty At Hyco we take pride in the design, quality and innovation of our products. The full Zen range is covered by a 2 year parts or replacement warranty.

Boiling and Chilled Water Zen Solo In stock now See page 12 Features and Benefits p. 10 Dedicated boiling water tap Instant true boiling 100 C or 98 C water ideal for a wide range of kitchen uses Cool touch insulated tap Safety lock 3 and 6 litre capacity 100 C or 98 C Zen Spa Coming soon See page 14 100 C or 98 C Filtered Cold Filtered Chilled Features and Benefits Boiling and chilled tap 2 in 1 hot and cold drinks station Instant true boiling 100 C or 98 C water ideal for a wide range of kitchen uses High quality cold (ambient), chilled or sparkling drinking water Filter included Safety lock on boiling side Sparkling

Boiling and Chilled Water Zen Life Coming soon See page 16 100 C or 98 C Hot & Cold Mixer Features and Benefits p. 11 Elegant 3 in 1 tap Instant true boiling 100 C or 98 C water ideal for a wide range of kitchen uses Standard sink hot and cold mixer Zen Ice Safety lock on the boiling side The only tap you need in your kitchen Perfect for retro-fit applications as well as new kitchens Coming Soon See page 18 Filtered Cold Filtered Chilled Sparkling Features and Benefits Cold drinks station Includes Zen range tap, undersink chiller and drinking water filter

Boiling and Chilled Water Zen Solo Boiling Water Tap 3 and 6 litre boiling water tank Usage p. 12 A Zen Solo boiling water tap is a stylish, modern, time and space saving addition to any kitchen replacing the need for a traditional kettle, counter top or wall mounted boiling water unit. Instant boiling water is ideal for a wide range of kitchen uses including tea and coffee making, providing a quick start for boiling rice, pasta and vegetables and soaking oven dishes. Features and Benefits Dedicated boiling water tap Choice of two temperature models provide instant true boiling 100 C or near boiling 98 C water Time saving provides instant hot water so no waiting for the kettle to boil Space saving frees up worktop space by eliminating the need for a kettle Energy saving no energy wasted boiling more water than is required Innovative aerogel insulation Smart technology algorithms learn and predict usage: on when you need it, off when you don t Low energy losses - see table below Designed and assembled in the UK Polished chrome 360 swivel tap Cool touch insulated tap Status ring on base of tap to indicate ready or heating (green/red LED) Safety lock Flow rate 2 l/m 3 litre tank as standard or 2 x 3 litre tanks to provide 6 litre capacity Power rating 1.55 kw for 3 litre model and 2 x 1.55 kw for 6 litre model Supplied with expansion vessel and pressure relief valve Zen font and drain available soon (see page 20) If you are in a hard scale area you may need a scale filter (see page 30) Product codes in the table are for Zen taps with 3 litre tank. For 6 litre tank models replace 3L with 6L in the product code. Product Code Temperature Heat Up Time ( C) (mins) SOLO3L100 100 14 SOLO3L98 98 13 Standing Loss (kwh/day)* 0.42 17 W 0.36 15 W *The standing loss for the 6 litre model which comprises 2 x 3L tanks will be double the value in the table

Boiling and Chilled Water Outer Casing Tap-polished chrome finish Tank-durable high impact PC/ABS Water Tank Stainless steel Heating Element Stainless steel Thermostat Electronic to control water up to boiling point Insulation Highly efficient aerogel thermal insulation Initial Draw off 20 cups/13 mugs based on 167ml cup and 250ml mug. Double draw off for 6 litre model. Safety Overheat temperature protection (manual re-set). Safety lock mechanism. Supplied expansion vessel and pressure relief valve must be fitted. Required hole diameter for mounting tap 32mm fits in a standard sink. Sink/counter top up to 50mm thick. Plumbing Must be installed by a suitably qualified person. Intended for connection to the mains water supply. Minimum water pressure 1 bar. Maximum water pressure 4.2 bar. If higher than this a pressure reducing valve may be required. Supplied expansion vessel and pressure relief valve must be fitted. Electrical Connection Installation must comply with current IEE wiring regulations. Supplied with a pre-wired (1m) BS plug. Approvals CE WRAS (98 C model only) p. 13 IP Rating IPX1 Installation This appliance must be installed in a frost free environment. Standard Warranty 2 years parts or replacement warranty. Product Code Height Width Depth Weight (kg) Empty Full ZEN Solo Tap (all models) 288 152 49 1.1 ZEN Solo 3L Tank 459 181 220 4.3 7.3

Boiling and Chilled Water Zen Spa 2 in 1 Boiling and Chilled Tap 3 and 6 litre boiling water tank Coming soon Usage The Zen Spa is a 2 in 1 hot and cold drinks station from one simple, stylish tap. Instant true boiling 100 C or 98 C is available alongside filtered cold, chilled or even sparkling water. In home environments a Zen Spa replaces the need for a kettle and provides high quality cold (ambient) drinking water to suit modern lifestyle requirements. p. 14 In office environments a Zen Spa replaces the traditional need for a wall mounted boiling water unit and separate floor standing chiller. The Zen Spa can be installed over a sink or with the stylish, tempered glass design Zen Font. Features and Benefits All of the features and benefits of the Zen Solo plus cold (ambient) or chilled drinking water from a single tap Filtered cold (ambient) drinking water models connect directly to the incoming water supply Filtered chilled drinking water models include an undersink chiller High quality taste and odour drinking water filter supplied with all models (F1T). If you are in a hard scale area you may need to upgrade to a scale filter (see page 30). Upgrade to sparkling water chiller unit if desired Filtered cold (ambient) typically for domestic use. Filtered chilled typically for commercial use. Zen Spa Options Product Code 98 C Boiling 100 C Boiling Filtered Cold Filtered Chilled SPA3L100 Yes Yes SPA3L98 Yes Yes SPA3L100C Yes Yes SPA3L98C Yes Yes Product codes in the table are for Zen Spa taps with 3 litre tank, for 6 litre tank models replace 3L with 6L in the product code. Add suffix G to any filtered chilled model to provide sparkling water. Product Code Temperature Heat Up Time Standing Loss ( C) (mins) (kwh/day)* SPA3L100 SPA3L100C 100 14 0.42 17 W SPA3L98 SPA3L98C 98 13 0.36 15 W * Standing loss figures are for the boiling tank only. The standing loss for the 6 litre model which comprises 2 x 3L tanks will be double the value in the table

Boiling and Chilled Water Boiling Specification ** Undersink chiller unit has the same specification as the Zen Ice, please see page 18. Outer Casing Tap-polished chrome finish Tank-durable high impact PC/ABS Water Tank Stainless steel Heating Element Stainless steel Thermostat Electronic to control water up to boiling point Installation This appliance must be installed in a frost free environment. Required hole diameter for mounting tap 32mm fits in a standard sink. Sink/counter top up to 50mm thick. Plumbing Must be installed by a suitably qualified person. Intended for connection to the mains water supply. Minimum water pressure 1 bar. p. 15 Insulation Highly efficient aerogel thermal insulation Initial Draw off 20 cups/13 mugs based on 167ml cup and 250ml mug. Double draw off for 6 litre model. Safety Overheat temperature protection (manual re-set). Safety lock mechanism. Supplied expansion vessel and pressure relief valve must be fitted. IP Rating IPX1 Maximum water pressure 4.2 bar. If higher than this a pressure reducing valve may be required. Supplied expansion vessel and pressure relief valve must be fitted. Electrical Connection Installation must comply with current IEE wiring regulations. Supplied with a pre-wired (1m) BS plug. Approvals CE Standard Warranty 2 years parts or replacement warranty. Product Code Height Width Depth Weight (kg) Empty Full ZEN Spa Tap (all models) 320 224 56 1.6 ZEN Spa 3L Tank 459 181 220 4.3 7.3

Boiling and Chilled Water Zen Life Boiling Water Tap with Hot and Cold Mixer 3 and 6 litre boiling water tank Coming soon Usage The Zen Life is a practical and stylish choice when considering the design and requirements of any kitchen environment. The elegant 3 in 1 tap provides instant true boiling 100 C or 98 C water alongside hot and cold mixer tap capabilities. It is perfect for retro-fit applications as well as new kitchens. This is the only tap you need in your kitchen and is ideal for a range of domestic and commercial applications. p. 16 Features and Benefits Creates a clutter free and simplified design within any kitchen or office environment Instant true boiling 100 C or 98 C water ideal for a wide range of kitchen uses Designed and assembled in the UK Time, space and energy saving Straight-forward operation with safety lock on the boiling water side Innovative aerogel insulation on boiling water tank minimises losses Boiling water tank has smart technology algorithms that learn and predict usage Cool touch insulated tap with 360 swivel function Boiling water status ring on base of tap to indicate ready or heating (green/red LED) Power rating 1.55 kw for 3 litre model and 2 x 1.55 kw for 6 litre model Standard sink hot and cold mixer supplied from your existing hot and cold water supply Elongated mixer lever for ease of use Consider installing a Speedflow to provide hot water for dish washing if there is no central heating system nearby If you are in a hard scale area you may need a scale filter (see page 30) Zen Life Options Product Code 98 C Boiling Water 100 C Boiling Water Hot and Cold Mixer LIFE3L100 LIFE3L98 Yes Yes Yes Yes Product codes in the table are for Zen Life taps with 3 litre tank, for 6 litre tank models replace 3L with 6L in the product code Product Code Temperature Heat Up Time ( C) (mins) LIFE3L100 100 14 LIFE3L98 98 13 Standing Loss (kwh/day)* 0.42 17 W 0.36 15 W *The standing loss for the 6 litre model which comprises 2 x 3L tanks will be double the value in the table

Boiling and Chilled Water Outer Casing Tap polished chrome finish Tank durable high impact PC/ABS Water Tank Stainless steel Heating Element Stainless steel Thermostat Electronic to control water up to boiling point Insulation Highly efficient aerogel thermal insulation Initial Draw off 20 cups/13 mugs based on 167ml cup and 250ml mug. Double draw off for 6 litre model. Safety Overheat temperature protection (manual re-set). Safety lock mechanism. Supplied expansion vessel and pressure relief valve must be fitted. IP Rating IPX1 Required hole diameter for mounting tap 32mm fits in a standard sink. Sink/counter top up to 50mm thick. Plumbing Must be installed by a suitably qualified person. Intended for connection to the mains water supply. Minimum water pressure 1 bar. Maximum water pressure 4.2 bar. If higher than this a pressure reducing valve may be required. Supplied expansion vessel and pressure relief valve must be fitted. Electrical Connection Installation must comply with current IEE wiring regulations. Supplied with a pre-wired (1m) BS plug. Approvals CE Standard Warranty 2 years parts or replacement warranty. p. 17 Installation This appliance must be installed in a frost free environment. Product Code Height Width Depth Weight (kg) Empty Full ZEN Life Tap (all models) 365 286 54 2.5 ZEN Life 3L Tank 459 181 220 4.3 7.3

Boiling and Chilled Water Zen Ice Cold Drinks Station with Undersink Chiller Coming soon Usage p. 18 Elegant cold drinks station supplying your choice of filtered cold, chilled and sparkling water. Ideal for use with the Zen Font in many domestic and commercial applications including office kitchens and canteens. Features and Benefits Stylish and practical Zen range tap included to be counter mounted (suitable to fill sports bottles/ carafes) Instant high quality filtered drinking water High quality taste and odour drinking water filter supplied with all models (F1T) (see page 30) Filter cartridges are simple and quick to change Undersink chiller unit can provide chilled water adjustable to your chosen temperature - choose a C model Upgrade the chiller to provide sparkling water if you desire - choose a CG model Zen Solo single outlet tap provides any one of cold (ambient), chilled and sparkling options. Zen Spa double outlet tap will provide any two of cold (ambient), chilled or sparkling water options. Plumbed in system gives reduced costs over bottle fed coolers Aluminium heat exchanger Zen Solo single outlet tap and filter available without a chiller unit to connect direct to mains cold water supply for a lower cost filtered cold (ambient) only drinking water option Zen Ice Options Product Code Undersink Filtered Cold Filtered Sparkling Chiller Included (Ambient) Chilled ICESOLO ICESOLOC ICESOLOCG Yes Yes Yes Yes Yes ICESPAC ICESPACG Yes Yes Yes Yes Yes Yes Product Code Power Chill Capacity (kw) (litres/hour) Current (amps) Chiller Unit C model CG model 0.155 0.155 25 25 0.6 0.6

Boiling and Chilled Water Under sink Chiller Specification ** Zen Solo and Zen Spa Tap dimensions can be found on pages 13 and 15. Installation Chilling requires the ambient temperature to be between 10 C and 40 C. Outer Casing Metal Capacity 150 glasses per hour (based on 167ml glass) Maintenance Sanitise every 6 months. Change filter approximately every 6 months. Plumbing Must be installed by a suitably qualified person. Minimum water pressure 1 bar. Maximum water pressure 3 bar. If higher than this a pressure reducing valve is required. Electrical Connection Supplied with a pre-wired (1.5m) black kettle lead cable BS plug. p. 19 See product instructions for full maintenance requirements. Refrigerant Type R134A Sparkling Option Supplied with a regulator and initial gas cylinder. IP Rating IP20 Approvals CE Standard Warranty 2 years parts or replacement warranty. Product Code Height Width Depth Weight (kg) Chiller Unit C model CG model 440 180 330 19 440 180 330 19.5

Boiling and Chilled Water Zen Font with Drain Coming Soon Usage p. 20 The Zen Font provides a stylish, sleek solution for installing a Zen tap where access to a sink is unavailable or not desired. Features and Benefits Stunning tempered glass design High quality chrome grille and stainless steel drain bowl Surround comes in two contemporary glass finishes, black or white Special order colours available at additional cost Font with integrated drain allows easy disposal of waste water Access to a drain is required Easy to clean Low maintenance Most suitable for use with the Zen Solo, Zen Spa and Zen Ice Product Code ZENFB ZENFW Colour Black White Drain Yes Yes

332 190 6 Boiling and Chilled Water Font Tempered glass Drain Bowl Stainless Steel Grille Chrome - diameter 125mm Installation Required hole diameter for mounting tap 32mm Sink/ counter top up to 50mm thick. Required hole diameter for mounting the bowl 127mm. p. 21 Plumbing Standard sink trap size, 34mm waste pipe. Standard Warranty 2 years parts or replacement warranty. Product Code Height* Length Width Weight (kg) ZENFB 66 332 190 ZENFW 66 332 190 0.1 0.1 * Height in the table includes the drain, excluding the drain, the height is 28mm.

Boiling and Chilled Water Omega Wall Mounted Boiling Water Heater 3 and 5 litre Coming Soon p. 22 Usage The Omega is a practical, stylish wall mounted unit that provides instant near-boiling water for preparing hot drinks in the workplace. The sleek, ergonomic design with curved lines gives a contemporary look whilst the robust, durable design specification, featuring a long life ceramic valve, makes it an essential appliance in the work environment. Features and Benefits Designed and assembled in the UK 2.85 kw gives fast heat up time and high recovery rate Time saving provides instant hot water so no need to wait for the kettle to boil Space saving frees up worktop space by eliminating the need for a kettle Energy saving no energy wasted boiling more water than is required Status ring on base of control valve to indicate ready or heating (green/ red LED) Robust, heavy duty ceramic control valve Cool touch control valve and water outlet reduce heat losses Simple to use and easy to install Durable, high impact and easy to clean white ABS case Sophisticated electronics maintain a constant supply of hot water- even when the unit is automatically re-filling after heavy usage 1 year on-site warranty as standard 3 year on-site warranty available on request at additional cost It is highly recommended that a filter system is fitted to protect against scale build up. Units may need to be de-scaled regularly. Scale damage is not covered by warranty. Product Code Capacity Initial Draw Off Heat Up Time (litres) (Cups / Mugs)* (mins) OMEG3 3 18 / 12 6 OMEG5 5 30 / 20 10 *Initial draw off based on 167ml cup and 250ml mug

Boiling and Chilled Water Outer Casing Easy clean high impact Polycarbonate/ ABS Plumbing Must be installed by a suitably qualified person. Heating Element 2.85 kw incoloy- sheathed type element Thermostat Electronic to control water up to boiling point Minimum water pressure 1 bar. Maximum water pressure 10 bar. Water Connection Inlet/ Outlet 2 x 1/2 BSP female adapter. 1 x tundish recommended. p. 23 Water Tank Stainless steel Insulation EPP (expanded polypropylene) Filter System Optional extra - highly recommended. See page 30 for filter options. IP Rating IPX0 Recovery Rate Recovery rate 175 cups per hour for all models based on 167ml cup size. Installation Install over a draining board, or work top fitted with a drip tray. At least 110mm clearance must be left above and below the unit to allow later removal of the jacket for service. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (1.5m), to the bottom left. Maintenance It is recommended the unit is descaled every 6 months. Approvals CE Standard Warranty 1 year on-site warranty as standard. 3 year on-site warranty available at additional cost. Product Code Height Width Depth Weight (kg) * Empty Full OMEG3 500 331 253 OMEG5 500 331 253 *Depth includes front control. Distance of water outlet from wall is 180mm. 7 7 10 12

Boiling and Chilled Water Microboil Wall Mounted Boiling Water Heater 3, 6, 8, 16 and 25 litre p. 24 Usage Provides instant near-boiling water for preparing hot drinks in the workplace. Features and Benefits Time saving provides instant hot water so no need to wait for the kettle to boil Space saving frees up worktop space by eliminating the need for a kettle Energy saving no energy wasted boiling more water than is required Sophisticated electronics maintain a constant supply of hot water even when the unit is automatically re-filling after heavy usage Stylish and compact design Available in white or stainless steel finish Simple to use and easy to install Heavy duty catering style chrome tap with lock-on option 1 year on-site warranty as standard 3 year on-site warranty available on request at additional cost For stainless steel models add suffix SS to the product code e.g. MBS3SS It is highly recommended that a filter system is fitted to protect against scale build up. Units may need to be de-scaled regularly. Scale damage is not covered by the warranty. Product Code Capacity Initial Draw Off Heat Up Time (litres) (Cups / Mugs)* (mins) MBS3 3 18 / 12 7 MBS6 6 38 / 25 14 MBS8 8 50 / 33 19 MBS16 16 100 / 66 38 MBS25 25 156 / 103 59

Boiling and Chilled Water Outer Casing White powder coated steel or stainless steel (SS) Heating Element 2.4 kw, Incoloy-sheathed type element Thermostat Electronic to control water up to boiling point Water Tank Copper 5 year corrosion guarantee Insulation Polystyrene Filter System Optional extra highly recommended. See page 30 for filter options. IP Rating IPX0 Recovery Rate Recovery rate 150 cups per hour for all models based on 167ml cup size. Installation Install over a draining board, or work top fitted with a drip tray. At least 40mm clearance must be left above the unit to allow later removal of the jacket for service. Plumbing Must be installed by a suitably qualified person. Minimum water pressure 1 bar. Maximum water pressure 10.0 bar. Water Connection Inlet/ Outlet 2 x 1/2 BSP male. Fittings required (not supplied): 2 x 15mm compression to 1/2 BSP female adapter. 1 x tundish recommended. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (1.5m) to the bottom left. Maintenance It is recommended the unit is descaled every 6 months. Approvals CE, KIWA Standard Warranty 1 year on-site warranty as standard. 3 year on-site warranty available at additional cost. p. 25 Product Code Height Width Depth Weight (kg) Empty Full MBS3 370 269 153 MBS6 420 312 171 MBS8 510 312 171 MBS16 545 364 218 MBS25 550 414 264 *Depth excludes the tap, for depth including tap add 90mm. 5.6 7.2 8.7 10.8 12.3 8.6 14.8 17.2 28.8 37.8

Boiling and Chilled Water Sapphire Stainless Steel Water Cooler Floor standing Illustrated with optional BREEAM kit fitted p. 26 Usage Ideal for high usage public areas, such as schools, gyms and office areas. Features and Benefits Instant high quality chilled drinking water Plumbed in system gives reduced costs over bottle fed coolers Elegant stylish design Stainless steel sink top and cabinet Push button bubbler and sports bottle/carafe filler included Direct chill technology High quality taste and odour drinking water filter supplied (F1T) (see page 30) Filter cartridges are simple and quick to change Chilled water temperature adjustable Optional BREEAM compliance kit Wall mounted water cooler available upon request Product Code Power Chill Capacity Current (kw) (litres/hour) (amps) SAP25SS 0.3 25 1.3

Boiling and Chilled Water Outer Casing Stainless steel Cooling Coil Stainless steel Capacity 150 glasses per hour (based on 167ml glass) BREEAM Compliance BREEAM compliant when fitted with optional BREEAM kit. Kit comprises stainless steel side panels and top panel as illustrated. Ensures cooler securely fixed to the wall and protects against vandalism. Cooler has adjustable foot and can be bolted to the floor. Plumbing Must be installed by a suitably qualified person. Minimum water pressure 1 bar. Maximum water pressure 3 bar, if higher than this a pressure reducing valve is required. Water Connection 15mm push-fit. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (1.5m), entry to the back of the unit. p. 27 Refrigerant Type R134A IP Rating IP23 Installation Cooler must be positioned 60 70mm from the wall to allow adequate ventilation. Chilling requires the ambient temperature to be between 10 C and 45 C. Maintenance Sanitise every 3 to 6 months. Replace filter approximately every 6 months. See product instructions for full maintenance requirements. Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) SAP25SS 960 340 325 BREEAM Kit 930 320 100 25 2

Boiling and Chilled Water Sapphire Water Cooler Floor standing Hot and Cold p. 28 Usage Ideal for use in office areas and waiting areas where there is moderate use. Features and Benefits Instant high quality chilled drinking water together with filtered hot water for tea and coffee making Plumbed in system gives reduced costs over bottle fed coolers Compressor cooling Low noise design Unique child-lock for hot water Power on indicator light Leak detecting valve High quality taste and odour drinking water filter supplied (F1T) (see page 30) Filter cartridges are simple and quick to change On/off switch for each of the heating and cooling functions Removable drip tray Product Code Power Chill Capacity Current (kw) (litres/hour) (amps) SAP02HC 0.58 2 2.5

Boiling and Chilled Water 1110mm 1110mm 1110mm 300mm 300mm 395mm Outer Casing Easy clean, high impact plastic Heating Element and Hot tank Food grade steel Heating Capacity 500 W>=90 C, 5 litres per hour (30 glasses) Hot tank capacity 1.1 litres Cooling Capacity 85 W<=10 C, 2 litres per hour (10 glasses) Cold tank capacity 3.3 litres Plumbing Must be installed by a suitably qualified person. Working pressure 1-4 bar (supplied with pressure reducing valve). Electrical Connection Supplied with a pre-wired (1.5m) BS plug, entry at the back of the unit. Maintenance Sterilise the water tank every 3-6 months. p. 29 Refrigerant type R134A/35g IP Rating IPXO Installation Unit must be positioned 100 200mm from the wall to allow adequate ventilation. Chilling requires the ambient temperature to be between 18 C and 38 C. Replace filter approximately every 6 months. See product instructions for full maintenance requirements. Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) SAP02HC 1110 300 395 16

Boiling and Chilled Water Drinking Water Filters Taste and odour, scale F1T and F2ST F3SST and F4SST Usage A water filter is often fitted with our boiling and chilled water products to provide high quality, great tasting drinking water. There are two general types of filter available. p. 30 Taste and odour carbon block filters help to improve the taste of drinking water by removing some of the chlorine present in UK mains water; these filters are ideal for cold/ chilled water feeds. Scale inhibiting filters are strongly recommended for use with boiling water products, particularly when installed in areas where scale is a known issue. This type of filter also offers chlorine reduction and helps to improve the taste. Features and Benefits Quick and easy to change filters Automatic water shut off head Choice of filters to suit a variety of applications High capacity filters available for heavy commercial use All filter models reduce chlorine, improving taste and odour F2ST, F3SST and F4SST models inhibit scale build up, reducing service costs associated to scale removal Does not remove important minerals from water, unlike most reverse osmosis or iron exchange units Integral mounting bracket All filters are WRAS approved Check system is suitable for the water quality in your area Scale maps of the UK are readily available online, please refer to these for information regarding water quality in your area For help choosing the most appropriate filter please contact our sales team Some products are supplied with a filter - please check relevant product page Product Code Function Taste & Odour Improvement Scale Reduction Use With F1T Chlorine reduction in cold water systems Yes No Zen Ice, Any cold supply F2ST As F1T plus scale control (up to 300 ppm) in moderate hard water areas for low throughput products* Yes Yes Omega Microboil F3SST F4SST As F1T plus scale control (up to 600ppm) in high hard water areas for high throughput products* Yes Yes Omega Microboil Zen Boiling Taps *ppm = parts per million CACO3

Boiling and Chilled Water Installation Wall mounting bracket integral to the filter system. Flush filter for 5 minutes prior to use. Replacement Cartridges Product codes in the data tables are for the full filter system including the head. For replacement cartridges add suffix CAR to the required product code: F1T replacement filter cartridge only: F1TCAR F2ST replacement filter cartridge only: F2STCAR F3SST replacement filter cartridge only: F3SSTCAR F4SST replacement filter cartridge only: F4SSTCAR Plumbing F1T and F2ST 1/4 push fit Maintenance F1T and F2ST: Replace cartridge after 6 months or when capacity is reached, whichever is sooner. F3SST and F4SST: Replace cartridge after 12 months or when capacity is reached, whichever is sooner. If the water flow rate becomes slow this is an indication that the filter cartridge needs replacing. Fitting a filter does not negate the need to service and descale your unit at regular intervals. Approvals WRAS Standard Warranty Filters are warranted for defects in material and workmanship only. F1T and F2ST: 6 months F3SST and F4SST: 12 months p. 31 F3SST and F4SST 3/8 push fit F2ST, F3SST and F4SST supplied with adaptors to facilitate connection to 15mm copper pipe. Product Code Particle Filtration Flow Rate Capacity (micron) (l/m) (L) F1T 1 1.9 5,678 F2ST 1 1.9 5,678 F3SST 5 3.7 12,000 F4SST 5 6.5 25,000 Product Code Height Width Depth Weight (kg) F1T 240 65 80 0.64 F2ST 240 65 80 0.64 F3SST 290 80 110 0.74 F4SST 490 80 110 1.24

p. 32

Product Category Water Heating ErP Ratings The Energy Related Products (ErP) Directive and Energy Labelling Directive require that from September 2015 all water heaters in scope meet minimum energy performance criteria and have energy labels which provide the energy rating of the product. The classifications range from A++; this being the most efficient and coded in green to a rating of G; this being less efficient and coded in red. p. 33 Such ratings provide transparency of efficiency and a comparable benchmark for water heating products, as standardised European Energy Labels are used. This catalogue contains the energy class for relevant water heating products. The full energy label and product fiche information for each of these products can be found on our website. hyco.co.uk

Water Heating Speedflow Unvented Water Heater 5, 10 and 15 litre Glass Lined or Stainless Steel Tank p. 34 Usage Ideal for use in cloakrooms and kitchens in offices, shops, student accommodation and domestic premises which have been extended and there is no central hot water system near by. One unit located under the kitchen sink is often used to supply hot water for light dishwashing in the kitchen sink and handwashing in the cloakroom basin. Selection Guide (approximate depending on usage). 1 basin: SF05K, 1 2 basins: SF10K, 2 3 basins: SF15K Features and Benefits Supplies hot water for up to 3 basins Can be used with regular taps including mixers Mains pressure flow rates 2.0 kw element as standard 1.2 kw element available for 10 and 15 litre models for restricted load applications Neon element on indicator Glass lined steel tank as standard Stainless steel tank available for the 10 and 15 litre models. Add suffix SS to the product code. External temperature control with frost protection setting Accessories may be needed to comply with the Water Regulations. Pressure reducing valve required for pressures above 4.2 bar and expansion vessel and check valve required if cold water draw off nearby. Kits available separately (see Speedflow Accessories). Optional thermostatic mixing valve available (see page 40) Not suitable for hair wash basins in hairdressing salons Product Code Capacity Power Heat Up Time Standing Loss (litres) (kw) (mins)* (kwh/day) SF05K 5 2.0 12 0.51 SF10K, SF10KSS SF10K12, SF10K12SS SF15K, SF15KSS SF15K12, SF15K12SS 10 15 *Approximate heat up time from 10 C to 75 C 2.0 1.2 2.0 1.2 23 38 35 57 0.63 0.71

Water Heating Outer Casing Easy clean, high impact plastic Heating Element Stainless steel flange type Thermostat Bulb type adj. to 75 C E setting approx. 50 C Water Tank Glass lined steel as standard. Stainless steel tank optional upgrade. Anode Replaceable grey magnesium (inspect annually) Insulation High density polyurethane foam Safety Overheat temperature protection (manual reset). Supplied pressure relief valve must be fitted in every case (set at 6 bar). Frost protection if power on. Optional thermostatic mixing valve to maintain hot water supplied to user at constant, safe temperature. IP Rating IPX4 Installation Site above or below the sink, but inlet and outlet must be at the top. Floor standing or wall mounted. Plumbing Must be installed by a suitably qualified person. It is recommended that flexible hoses are used for connection to facilitate future maintenance. Access to the thermal cut-out and element is located at base of unit. Minimum water pressure 0.5 bar. Maximum water pressure 4.2 bar. Water Connection Inlet/ Outlet 2 x 1/2 BSP male (100mm apart centre to centre). Fittings required (not supplied): 2 x 15mm compression to 1/2 BSP female adapter. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (1.5m). Approvals CE, WRAS Standard Warranty Glass Lined Tank 1 year parts or replacement warranty. Stainless Steel Tank 3 year tank warranty. p. 35 Product Code Height Width Depth Weight (kg) Empty Full SF05K 320 280 245 5.5 10.5 SF10K, SF10KSS SF10K12, SF10K12SS SF15K, SF15KSS SF15K12, SF15K12SS 410 530 310 310 280 280 6.8 16.8 8.3 23.3

Water Heating Speedflow Accessories Unvented Water Heater 5, 10 and 15 litre Depending on the details of the Speedflow installation, additional accessories may be needed to comply with the Water Regulations. See diagrams on the opposite page. SF3 Kit Expansion vessel and check valve 2 litre expansion vessel set at 3.5 bar p. 36 SF4 Kit Expansion vessel, check valve and pressure reducing valve SF5 Kit Pressure reducing valve Set at 3 bar * All SF kit components WRAS approved Accessory Height Width Depth Weight (kg) Expansion vessel 225 120 120 1.0 Check valve 65 25 25 0.1 Pressure reducing valve 73 64 46 0.3

Water Heating Diagram A Pressure is below 4.2 bar and hot water expansion can be accommodated in the pipework Hot Cold Pressure relief valve Nearest cold draw off Service valve T piece To drain Cold water mains Speedflow Length of pipework required for expansion 5 litres 1.4m 10 litres 2.8m 15 litres 4.2m * No accessories needed Diagram B Pressure is below 4.2 bar and hot water expansion cannot be accommodated in the pipework Hot Pressure relief valve Expansion vessel Nearest cold draw off Cold Check valve Service valve Speedflow T piece To drain Cold water mains p. 37 * Accessory SF3 needed Diagram C Pressure is above 4.2 bar and hot water expansion cannot be accommodated in the pipework Hot Pressure relief Expansion vessel Nearest cold draw off Pressure reducing valve Cold Check valve valve Service valve T piece To drain Cold water mains Speedflow * Accessory SF4 needed Diagram D Pressure is above 4.2 bar and hot water expansion can be accommodated in the pipework Hot Cold Pressure relief valve Nearest cold draw off Pressure reducing valve Service valve T piece To drain Cold water mains Speedflow Length of pipework required for expansion 5 litres 1.4m 10 litres 2.8m 15 litres 4.2m * Accessory SF5 needed

Water Heating Powerflow Unvented Water Heater 30, 50 and 90 litre 30L 50L & 90L p. 38 Usage Suitable for hand washing and dishwashing where a number of hot water outlets are required such as kitchens, schools, restaurants, washrooms and offices. The ideal solution for light industrial, commercial and light domestic hot water requirements. Selection Guide (approximate depending on usage) 3 5 basins: PF30LC-1, 4 6 basins: PF50LC-1, 6 10 basins or 1 bed/1 shower: PF90LC-1 Features and Benefits Can be used with regular taps, including mixers Mains pressure flow rates 3.0 kw element as standard 1.0 kw element available for restricted load applications Stainless steel tank External temperature control Neon element on indicator 3 year tank warranty, 1 year on electrical components Slimline profile depth from 295mm Highly efficient thermal insulation Comprehensive range of safety features Comes complete with unvented accessory kit Optional thermostatic mixing valve available Cable pre-wired (1.5m) Product Code Capacity Power Heat Up Time Standing Loss (litres) (kw) (mins)* (kwh/day) PF30LC-1 PF30LC1KW 30 3.0 1.0 21 63 0.93 PF50LC-1 PF50LC1KW 50 3.0 1.0 40 120 1.16 PF90LC-1 PF90LC1KW 90 3.0 1.0 86 258 1.25 *Heat up time from 13 C to 60 C

Water Heating Outer Casing Easy clean, high impact plastic Access to the thermal cut-out and element is located at base of unit. Heating Element Stainless steel incoloy Thermostat Capillary type adjustable to 65 C Water Tank Stainless steel Anode Replaceable grey magnesium anode (inspect annually) Insulation High density polyurethane foam (CFC free) Safety Overheat temperature protection (manual reset). Factory fitted temperature and pressure relief valve (set at 7 bar 90 C). Pressure reducing valve (set at 3 bar). Pressure relief valve at 6 bar. Optional thermostatic mixing valve to maintain hot water supplied to user at constant, safe temperature. IP Rating IPX4 Installation Must be installed vertically with inlet/outlet connections at base. Space required above and below unit to allow maintenance 400mm. Unvented Accessory Kit Supplied kit must be fitted. Contains expansion vessel with fixing bracket (5L for PF30LC-1 and PF50LC-1, 8L for PF90LC-1), inlet group, flexible hose and 2 tundishes. Plumbing Must be installed by a suitably qualified person. Minimum water pressure 0.8 bar. Maximum water pressure to pressure reducing valve 12 bar. Working water pressure 3 bar. Water Connection Inlet/outlet connection 1/2 BSP male. (100mm apart centre to centre) Fittings required (not supplied): 2 x 15mm compression to 1/2 BSP female adapter. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a suitably rated isolating switch with a contact separation of at least 3mm in all poles. Approvals CE, WRAS, KIWA Standard Warranty 1 year parts or replacement warranty. 3 year tank warranty. p. 39 Product Code Height Width Depth Weight (kg) Empty Full PF30LC-1 PF30LC1KW 620 380 295 9 39 PF50LC-1 PF50LC1KW 915 380 295 13 63 PF90LC-1 PF90LC1KW 930 540 385 24 114

Water Heating Thermostatic Mixing Valve Unvented Accessory TMV15-1 p. 40 Usage For use with the Speedflow or Powerflow unit or larger unvented cylinders, where maintaining water supply at a safe and constant temperature is necessary. Ideal for use in many applications including schools, hospitals, public washrooms, restaurants and office and commercial kitchens. Delivers safe hot water to basins, baths and showers. Features and Benefits Allows water to be stored at high temperatures and blended with cold water to a pre-set outlet temperature Maintains water supply at a safe and constant temperature Allows extension of effective capacity by mixing high temperature water with cold to achieve the pre-set temperature level Allows water to be safely stored above 60 C Failsafe design Temperature setting range 35 46 C Temperature accuracy ± 2 C Lockable control knob with unique key to prevent unauthorised temperature adjustment Product Code Temperature Cold Water Failsafe Setting Range ( C) Connection (BSP) TMV15-1 35-46 15mm compression Yes

Water Heating Installation Install on the hot outlet of the water heater, with a separate feed from the cold mains supply. Plumbing Must be installed by a suitably qualified person. Water Connection Hot & Cold inlet 2 x 15mm compression. Mixed Outlet 1 x 15mm compression. Fittings required (not supplied): none. p. 41 Maximum inlet temperature 85 C. Maximum inlet pressure ratio (H/C or C/H) 5:1. Minimum temp difference between the inlet hot water and the outlet mixed water for fail safe 10 C. Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) TMV15-1 115 140 37 0.5

Water Heating Everlast Direct Unvented Water Heater 90 to 600 litres p. 42 Usage The Everlast Direct is a large capacity unvented water heater suitable for small flats and houses or much larger requirements such as hotels, sports centres or nursing homes. Features and Benefits Available in capacities from 90 to 600 litres Mains pressure for high flow rates 2 year warranty on the controls High quality duplex stainless steel tank Reliable and flexible siting due to external expansion 25 year tank guarantee Product Code (and litres) Re - Heat Time (minutes)* Standing Loss (kwh/day) Height Diameter Weight (kg) Empty Full EVL90DR EVL120DR EVL150DR EVL180DR EVL210DR EVL250DR EVL300DR EVL400DR EVL500DR EVL600DR 69 103 137 171 205 221 308 345 447 564 0.96 760 545 21 111 1.11 940 545 26 146 1.26 1140 545 33 183 1.40 1320 545 38 218 1.48 1510 545 41 251 1.76 1760 545 46 296 2.03 1980 545 55 355 2.80 1505 690 64 464 3.25 1830 690 80 580 3.90 2205 690 96 696 *Re-heat time is for 70% of the contents of the cylinder. Where cylinders are fitted with multiple immersion heaters, performance is for lower 3 kw heater.

Water Heating Outer Casing Steel Heating Element Incoloy, immersion type: 1 x 3.0 kw 90 litres 2 x 3.0 kw > 90 litres <400 litres Titanium: 3 x 3.0 kw > 400 litres Thermostat Rod type adjustable to 65 C Installation Floor standing Ensure floor can take cylinder weight full. Plumbing Must be installed by a suitably qualified person. Minimum flow rate required 20 l/m Minimum water pressure 1.5 bar. Water Tank High quality duplex stainless steel vessel No sacrificial anode avoids the need for regular inspection. Insulation Injected polyurethane foam Safety Overheat temperature protection 85 C (manual reset). Cylinder Kit Contents Cold water inlet set. 15 x 22mm tundish. Temperature and pressure relief valve (set at 7 bar 90 C). Expansion vessel and bracket 12, 18 or 24 litre depending on capacity. Immersion heater(s). Maximum water pressure to pressure reducing valve 15 bar. Working water pressure 3 bar. All cylinder connections are 22mm compression. Cylinder diameter excludes external pipework. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a suitably rated isolating switch with a contact separation of at least 3mm in all poles. Approvals CE, WRAS Standard Warranty 2 year warranty on all controls. 25 year tank warranty. p. 43 Expansion relief valve set at 6 bar. Pressure reducing valve set at 3 bar. Selection Guide (approximate depending on usage) Application 1 bed / 1 shower 2 bed / 1 bath / 1 shower 3 bed / 1 bath / 2 showers 4 bed / 1 bath / 2 showers 4 bed / 1 bath / 3 showers 5 Bed / 2 bath / 2 showers Large Domestic Dwellings / Commercial Applications Suggested Product 90 litre / 120 litre 150 litre / 180 litre 180 litre 180 litre / 210 litre 250 litre 300 litre 300 litre - 600 litre

Water Heating Rho Instantaneous Inline Water Heater Thermostatic and Non Thermostatic 4.4 and 6.0 kw p. 44 Usage Suitable for handwashing at a single sink. Confirm that the flow rate and temperature performance is adequate for your application using the chart and tables provided. Features and Benefits Thermostatic Model Only Supplies hot water to a single outlet Bare wire heating system gives fast heat up time Heats the water instantly as it flows through the unit Energy efficient no standing heat losses 4.4 or 6.0 kw power rating Compact space saving design Intended for use with spray head taps with removable M22/M24 nozzles Compatible taps available separately External electronic thermostatic control accurate to the nearest degree Blue LED temperature display Energy saving only uses the power required to deliver the chosen temperature Heating power adjusted electronically to compensate for temperature, flow rate and water pressure variations Temperature factory set at 38 C and can be adjusted by the user between 30 C and 48 C After power off/on the unit will recall the last usage outlet temperature Product Code Power Thermostatic Max Flow Rate Standing Loss (kw) (l/m) handwash* (kwh/day) IN44 IN44T 4.4 No Yes 2.4 0.0 IN60 IN60T 6.0 No Yes 3.3 0.0 *Flow rates based on incoming water supply temperature of 12 C, handwash at 38 C

Water Heating Outer Casing Easy clean high impact ABS Heating Element Bare-wire heating system (3 nickel chrome heating elements) Controls (Thermostatic Model only) Temperature display ( C) Power on/off button +/- controls allow the user to set the required temperature The temperature display will flash if the set temperature cannot be reached. Taps and Tap Spray Nozzles Intended for use with spray head taps with removable M22/M24 nozzles. Compatible taps available. Important the supplied tap spray nozzle must be fitted in the tap for best performance. 4.4 kw: 2.0 l/m, 6.0 kw: 2.5 l/m, other flow rates available on request. Safety Overheat temperature protection 80 C. Thermostatic model water temperature controlled to maintain user selected temperature between 30 C and 48 C as water pressure conditions vary. IP Rating IPX4 Installation This appliance must be installed in a frost free environment. The heater should be located as close as practical to the hot water outlet to avoid unnecessary heat losses through the pipework. Plumbing Must be installed by a suitably qualified person. Minimum flow rate 2.0 l/m. Minimum water pressure 1 bar. Maximum water pressure 7.5 bar. Water resistivity 1300 Ωcm. Water Connection Inlet/Outlet 2 x 1/2 BSP male (40mm apart centre to centre). Fittings required (not supplied): 2 x 15mm compression to 1/2 BSP female adapter. Suitable for use with pre-heated water e.g. solar heating systems subject to maximum inlet water temperature 60 C. Electrical Connection Installation must comply with current IEE regulations. Single phase. Fuse rating guide 19 amps for 4.4 kw and 27 amps for 6.0 kw. The product should be connected to the fixed wiring of the property via a suitably rated isolating switch with a contact separation of at least 3mm in all poles. Cable pre-wired (0.7m). Approvals CE, WRAS Standard Warranty 1 year parts or replacement warranty. p. 45 Product Code Height Width Depth Weight (kg) Empty IN44 IN44T 140 190 80 1.56 IN60 IN60T 140 190 80 1.56

Water Heating Aquila Instantaneous Inline Water Heater Thermostatic, 9.6 kw p. 46 Usage Suitable for hand washing at up to 2 basins, or for a single light shower, or light dishwashing. Confirm that the flow rate and temperature performance is adequate for your application using the chart and tables provided. Features and Benefits Supplies hot water to one or two outlets depending on application Bare wire heating system gives fast heat up time Heats the water instantly as it flows through the unit Energy efficient no standing heat losses Energy saving only uses the power required to deliver the chosen temperature External electronic thermostatic control accurate to the nearest degree 9.6 kw power rating Slimline design Heating power adjusted electronically to compensate for temperature, flow rate and water pressure variations LED temperature display Temperature factory set at 38 C and can be adjusted by the user between 30 C and 60 C One programmable memory setting After power off/on the unit will recall the last usage outlet temperature Suitable for use with spray head taps with removable M22/M24 nozzles taps available separately Product Code Power Thermostatic Max Flow Rate Standing Loss (kw) (l/m) handwash* (kwh/day) IN96T 9.6 Yes Handwash or Shower 5.2 0.0 Dishwash 3.6 *Flow rates based on incoming water supply temperature of 12 C, hand wash or shower at 38 C, dish wash at 50 C

Water Heating Outer Casing Easy clean high impact ABS Heating Element Bare-wire heating system (2 nickel chrome heating elements) Control Screen (from left to right) Temperature display ( C) Actual flow rate display (l/m) Heating power display (%) Memory save selected temperature. Touch screen arrow keys allow the user to set the required temperature. Touch screen power on/off control. The heater should be located as close as practical to the hot water outlet to avoid unnecessary heat losses through the pipework. Plumbing Must be installed by a suitably qualified person. Minimum flow rate 2.5 l/m. Minimum water pressure 1 bar. Maximum water pressure 7.5 bar. Water resistivity 1300 Ωcm. Water Connection Inlet/Outlet 2 x 1/2 BSP male (100mm apart centre to centre). Fittings required (not supplied): 2 x 15mm compression to 1/2 BSP female adapter. p. 47 The temperature display will flash if the set temperature cannot be reached. Flow Dial Increase/decrease maximum water flow rate. Safety Overheat temperature protection 75 C (manual reset). Water temperature electronically controlled to maintain user selected temperature between 30 C and 60 C as water pressure conditions vary. IP Rating IPX4 Installation This appliance must be installed in a frost free environment. Suitable for use with pre-heated water e.g. solar heating systems subject to maximum inlet water temperature 60 C. Electrical Connection Installation must comply with current IEE regulations. Single phase, fuse rating guide 42 amps. The product should be connected to the fixed wiring of the property via suitably rated isolating switch with a contact separation of at least 3mm in all poles. Approvals CE, WRAS Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) Empty IN96T 380 230 90 2.02

Water Heating Instantaneous Inline Water Heater Temperature Performance Charts Incoming Water Supply Temp 17 C p. 48 Incoming Water Supply Temp 12 C Delivered Temperature ( C) Delivered Temperature ( C) Water Flow Rate (l/m) Water Flow Rate (l/m) Incoming Water Supply Temp 7 C Delivered Temperature ( C) Water Flow Rate (l/m) Handwash or shower at 38 C Kitchen sink at 50 C Max Temp 48 C Min flow rate 2.0 l/m (IN44T and IN60T) Max Temp 60 C Min flow rate 2.5 l/m (IN96T)

Water Heating Selection Guide Check the flow rate and water temperature will be adequate for your application using the chart and tables provided. Take into account that the incoming water supply temperature will be lower in winter than summer. Temperature Rise Temperature rise from ambient for an instantaneous water heater (TR) TR = kw rating x 14.3 / flow rate l/m Temperature/Flow Rate Maximum temperature increase from ambient incoming water supply temperature at a flow rate of: Flow Rate (l/m) IN44T IN60T IN96T 2.0 2.5 3.0 4.0 5.0 31 C 25 C 21 C 43 C 34 C 28.5 C 45 C 34 C 27 C p. 49 Application Recommended temperature for hand washing or shower 38 C. Recommended temperature for a kitchen sink 50 C. Rho and Aquila Instantaneous water heaters are intended for use with spray head taps with removable M22/M24 nozzles. A tap spray nozzle must be fitted in the tap to control the water flow rate and to provide best performance and energy and water efficiency. Product Code Power Application Water Flow Rate (kw) for best performance (l/m) IN44T IN60T IN96T 4.4 6.0 9.6 Handwashing at a single sink Handwashing at a single sink Handwashing at up to 2 basins or Light dishwashing at a single sink or Light shower 2.0 2.5 2.0 per basin 3.0 per sink 4.0-4.5

Water Heating Taps Non-Concussive, Single Level Mixer Automatic Infrared Usage This range of taps is ideal for use with Hyco Rho and Aquila instantaneous water heaters to provide optimum handwashing performance in washroom settings and for use with Hyco Speedflow and Powerflow water heaters. p. 50 Features and Benefits Sprayhead range of taps all with removable M22/M24 nozzles Reduce water consumption by up to 50% compared to traditional taps by controlling the flow rate Save energy by up to 50% compared to traditional taps by reducing the amount of hot water required per handwash Where the taps are used with a Speedflow or Powerflow water heater an optional thermostatic mixing valve is recommended (see page 40) Hyco Rho and Aquila instantaneous water heaters are only intended for use with spray head taps of this type. If traditional taps which do not control the water flow rate are used then optimum performance will not be achieved. All taps supplied complete with a choice of three tap spray nozzles 2.0, 2.5 or 3.0 l/m Other flow rates available on request Product Code Description Reach TAPNC Non-concussive tap 150 TAPSLM Single lever 160 mixer tap TAPIFR Automatic touch 150 free tap Tap Spray Nozzle Options Product Code Max Flow Rate Best suited Colour Code (l/m) to water heater Identification IN-TSN-2.0 2.0 4.4 kw Rho White/Black IN-TSN-2.5 2.5 6.0 kw Rho White/Green IN-TSN-3.0 3.0 9.6 kw Aquila White/Lilac

Water Heating Non-Concussive Tap Simple push tap operation. Tap functions for a period of time and then closes automatically. Prevents vandalism and continuous running and saves water. Use for hot or cold water blue and red identification rings supplied with each tap. WRAS approved Single Lever Mixer Tap Simple manual operation by lifting the control lever up and down. Rotating the control lever clockwise or anti-clockwise reduces or increases the mixed water temperature. p. 51 Automatic Infrared (Touch Free) Tap Hygienic no touch automatic operation. Dual mains or battery powered operation. Complete with cable for connection to the power supply. Usage timer prevents vandalism and continuous running and saves water. Mixer lever gives option to dispense hot and cold water if required. WRAS approved Standard Warranty 1 year parts or replacement warranty for all tap models. Product Code Height Diameter Reach Weight (kg) TAPNC 140 50 150 0.8 TAPSLM 160 50 160 1.0 TAPIFR 140 50 150 1.7

Water Heating Wave Instantaneous Hand Wash 3.0 kw, Manual and Automatic Usage Designed for light handwashing at a single basin. p. 52 Features and Benefits Manual Unit Unlimited hot water for light hand washing at a single washroom basin Designed and assembled in the UK Stylish and compact ergonomic design Energy efficient heats water instantly at point of use so no long pipe runs and no standing heat losses 3.0 kw element Cost effective hot water for handwashing Integral inlet tap and swivel 200mm spray arm Optimised spray head to prevent splashing Durable easy to clean cover Simple to install and use Separate on/off and temperature and flow rate control No need to re-calibrate flow rate every usage Correct temperature instantly achieved every time Automatic Unit Automatic no touch operation Manual temperature and flow rate control Product Code Power On/ Off Max Flow Rate Standing Loss (kw) Control (l/m) Handwash* (kwh/day) HW30M 3.0 Manual 1.6 0.0 HW30A 3.0 Auto 1.6 0.0 *Flow rate based on incoming water supply temperature of 12 C, handwash at 38 C

Water Heating Outer Casing Easy clean, high impact Polycarbonate/ABS Wall mounted. Base assembly is secured to the wall by two fixing screws. Full fixing pack supplied. Heating Element Copper-sheathed coil Water Container Glass reinforced nylon Controls On/Off: HW30M Rotary switch HW30A Automatic no touch operation Plumbing Must be installed by a suitably qualified person. Minimum water pressure 1.0 bar. Maximum water pressure 6.0 bar. Water Connection Inlet 1 x 15mm compression. Outlet 1 x Push fit chrome plated brass spray arm 200mm (8 ). p. 53 Temperature Selection: HW30M and HW30A Rotary dial Safety Self re-setting thermal cut-out set at 60 C. Manual resettable cut-out set at 90 C. Pressure relief valve to prevent high-pressure build up. Temperature stabilised unit maintains consistent outlet temperature as water pressure conditions vary. IP Rating IPX4 Installation The appliance must be installed in a frost free environment. ONLY USE THE FITTINGS SUPPLIED SO THAT THE UNIT IS NOT PRESSURISED. Fittings required (not supplied): none. Electrical Connection Installation must comply with current IEE regulations. This product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Approvals CE, WRAS Standard Warranty 1 year parts or replacement warranty. Product Code Height* Width Depth Weight (kg) Empty HW30M 170 240 100 1.5 HW30A 170 240 100 1.5 *Dimensions excluding spout.

Water Heating Handyflow Oversink Vented Point of Use Water Heater 5 litre p. 54 Usage Ideal for occasional use light dishwashing at a single kitchen sink in the workplace, for example portable buildings, offices, shops, workshops, garages and other small commercial premises. Features and Benefits Open outlet heater to supply hot water to a single sink Ideal when economy and ease of installation are the key priorities Stylish design and slimline profile depth only 7 (180mm) Comes complete with tap and chrome spout Thermal cut-out can be re-set rather than requiring to be replaced 2.0 kw element External temperature control with frost protection setting Neon element on indicator Wall fixing bracket included and cable pre-wired (1m) saves time on installation No need for expansion vessel, relief valve or reducing valve Product Code Capacity Power Heat Up Time (litres) (kw) (mins)* HF05LM 5 2.0 12 Standing Loss (kwh/day) 0.32 *Heat up time from 10 C to 75 C

Water Heating Outer Casing Easy clean, high impact plastic Heating Element Copper-sheathed type element Thermostat Capillary type adjustable to approx. 80 C E setting approx. 55 C Water Tank Polypropylene Insulation High density polystyrene CFC free Spout Length 10 (250mm) Safety Open outlet non-pressurised system, supplied tap and spout must be used. Safety re-settable thermal cut out. Frost protection setting when power is switched on. Heating Cycle It is normal for the spout on this type of unit to drip slightly during the heating cycle, caused by the water expanding as it heats up. IP Rating IP24 Plumbing Must be installed by a suitably qualified person. Minimum water pressure 0.3 bar. Maximum water pressure 8.0 bar. Water Connection Inlet valve/tap 1 x 15mm compression. Outlet 1 x chrome plated brass spray arm. Fittings required (not supplied): none. ONLY USE THE FITTINGS SUPPLIED SO THAT THE UNIT IS NOT PRESSURISED. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (1m). Approvals CE Standard Warranty 1 year parts or replacement warranty. p. 55 Installation Must be sited above a sink using the wall fixing bracket supplied, with the spout and tap located at the bottom of the unit. Product Code Height Width Depth HF05LM 400 270 180 Weight (kg) Empty Full 3.5 8.2

Water Heating Handyflow Undersink Vented Point of Use Water Heater 5 litres p. 56 Usage Ideal for occasional use light dishwashing at a single kitchen sink in the workplace, for example portable buildings, offices, shops, workshops, garages and other small commercial premises. Features and Benefits Open outlet heater to supply hot water to a single sink Ideal when economy and ease of installation are the key priorities Stylish design and slimline profile depth only 7 (180mm) Can be installed in an under-sink cupboard giving less visual impact than the Handyflow Oversink Comes complete with vented mixer tap and hoses Thermal cut-out can be re-set rather than requiring to be replaced 2.0 kw element External temperature control with frost protection setting Neon element on indicator Cable pre-wired (1m) saves time on installation No need for expansion vessel, relief valve or reducing valve Product Code Capacity Power Heat Up Time (litres) (kw) (mins)* HF05MVC 5 2.0 12 Standing Loss (kwh/day) 0.32 *Heat up time from 10 C to 75 C

Water Heating Outer Casing Easy clean, high impact plastic Heating Element Incoloy-sheathed coil Thermostat Capillary type adjustable to approx. 80 C E setting approx. 55 C Water Tank Polypropylene Insulation High density polystyrene CFC free Safety Open outlet non-pressurised system, vented mixer tap must be used. Installation Must be sited below a sink, with the inlet and outlet connections at the top of the unit. Plumbing Must be installed by a suitably qualified person. Minimum water pressure 0.5 bar. Maximum water pressure 8.0 bar. Water Connection Cold water connection 1 x 15mm compression. Outlet 1 x vented tap (supplied). Fittings required (not supplied): none. ONLY USE THE FITTINGS SUPPLIED SO THAT THE UNIT IS NOT PRESSURISED. p. 57 Safety re-settable thermal cut out. Frost protection setting when power is switched on. Heating Cycle It is normal for the vented tap on this type of unit to drip slightly during the heating cycle, caused by the water expanding as it heats up. IP Rating IP24 Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (1m). Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth HF05VC 400 270 180 Weight (kg) Empty Full 3.5 8.2

p. 58

Product Category Hand Dryers and Hair Dryers p. 59

Hand Dryers Jetstream Blade 1.9 kw Automatic Hand Dryer Energy Efficient p. 60 Usage Suitable for many public washroom applications including restaurants, shops and shopping centres, office buildings, pubs, motorway services, factories and supermarkets. Features and Benefits High speed giving fast drying times Saves energy relative to traditional hand dryers from reduced drying times Modern stylish design Automatic double side blades Hygienic automatic operation reduces the risk of spreading germs 2 power output settings 800 and 1900 W provide a low power rating option to increase energy efficiency Auto heating setting allows energy saving by automatically switching off the element if the ambient temperature is above 25 C (automatic/all time heating) Blue Dry Zone LED indicator gives visible indication to ensure hands are placed in the warm air stream Dust filter and drip tray Product Code Finish Power Sound Level (kw) (db) Dry Time (seconds) Air Speed (m/s) JETB190W White 1.9 70 10 90

Hand Dryers Outer Casing Easy clean high impact ABS Heating Element 1100 W (on/off setting) Motor 800 W Carbon Brush 25,000 RPM Current 8 amps Air Speed 90 m/s Installation Full fixing pack supplied. Cable entry to the left of the unit. LED Display The hand dryer will display the current temperature of the room when in standby mode. When operated a 10 second countdown will be displayed. Electrical Connection Installation must comply with current IEE Regulations. p. 61 Operation Touch free automatic. Safety Overheat temperature protection. Safety timer prevents continuous running. IP Rating IPX1 Cable pre-wired (1.2m). The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) JETB190W 687 300 225 10.8

Hand Dryers Jetstream Ellipse 1.6 kw Automatic Hand Dryer Energy Efficient p. 62 Usage Suitable for many public washroom applications including restaurants, shops and shopping centres, office buildings, pubs, motorway services, factories and supermarkets. Features and Benefits High speed giving fast hand drying times Saves energy relative to traditional hand dryers from reduced drying times Modern stylish design Hygienic automatic operation reduces the risk of spreading germs 1.6 kw power rating Option to reduce power rating to 0.8 kw on installation to increase energy efficiency Dry Zone LED indicator gives visible indication to ensure hands are placed in the warm air stream Dual colour LED sensor indicator (green: on, red: off) Durable metal vandal resistant case Product Code Finish Power Sound Level (kw) (db) Dry Time (seconds) Air Speed (m/s) JET1600 White 1.6 77 10-15 100 JET1600BSS Brushed SS 1.6 77 10-15 100

Hand Dryers Outer Casing JET1600 white enamel steel JET1600BSS brushed stainless steel Installation Full fixing pack supplied. Cable entry to the left at the base of the unit. Heating Element 450 900 W (adjustable) Motor 350 700 W (adjustable) Carbon Brush 12,000 18,000 RPM (adjustable) Current 7 amps Air Speed 75 100 m/s (adjustable) Air Volume 87 116 m 3 /h (adjustable) Operation Touch free automatic. Electrical Connection Installation must comply with current IEE Regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. p. 63 Safety Overheat temperature protection. Safety timer prevents continuous running. IP Rating IPX1 Product Code Height Width Depth Weight (kg) JET1600 287 205 180 5.8 JET1600BSS 287 205 180 5.8

Hand Dryers Jetstream Curve 1.8 kw Automatic Hand Dryer Usage p. 64 Suitable for many public washroom applications including restaurants, shops and shopping centres, office buildings, pubs, motorway services, factories and supermarkets. Features and Benefits High speed giving fast hand drying times Saves energy relative to traditional hand dryers from reduced drying times Modern stylish 'curve' design Hygienic automatic operation reduces the risk of spreading germs 1 power output setting 1.8 kw Blue Dry Zone LED indicator gives visible indication to ensure hands are placed in the warm air stream Stainless steel case Available in white, silver or brushed stainless steel finish Easy clean, vandal resistant, durable casing Product Code Finish Power Sound Level (kw) (db) Dry Time (seconds) Air Speed (m/s) JETC18W JETC18S White Silver 1.8 1.8 JETC18BSS Brushed SS 1.8 78 10-15 80 78 78 10-15 10-15 80 80

Hand Dryers Outer Casing Stainless steel Heating Element 1200 W Motor 600 W Carbon brush Dual ball bearings 20,000 RPM Current 8 amps Installation Full fixing pack supplied. Cable entry bottom left at the base of the unit. Electrical Connection Installation must comply with current IEE Regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. p. 65 Air Speed 80 m/s Operation Touch free automatic. Safety Overheat temperature protection. Safety timer prevents continuous running. IP Rating IPX1 Cable (1m) supplied not fitted. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) JETC18W 325 280 170 5.4 JETC18S 325 280 170 5.4 JETC18BSS 325 280 170 5.4

Hand Dryers Jetstream Slimline 1.0 kw Automatic Hand Dryer Energy Efficient p. 66 Usage Suitable for many public washroom applications including restaurants, shops and shopping centres, office buildings, pubs, motorway services, factories and supermarkets. The slimline profile makes this hand dryer particularly suitable for restricted space applications such as portable buildings. Features and Benefits High speed giving fast hand drying times Saves energy relative to traditional hand dryers from reduced drying times Modern compact design with slimline profile depth only 100mm (4 ) Hygienic automatic operation reduces the risk of spreading germs Low 1.0 kw power rating Option to reduce power rating to 0.35 kw on installation to increase energy efficiency Durable white steel vandal resistant case Product Code Finish Power Sound Level (kw) (db) Dry Time (seconds) Air Speed (m/s) JETS10W White 1.0 78 10-15 70

Hand Dryers Outer Casing White epoxy on steel Heating Element 325 500 W (adjustable) and on/off function both set on installation Motor 350 500 W (adjustable) set on installation Carbon brush Dual Ball bearings 29,000 RPM Installation Full fixing pack supplied. Cable entry bottom left at base of the unit. Electrical Connection Installation must comply with current IEE Regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. p. 67 Current 4.3 amps Air Speed 45 70 m/s (adjustable) Air Volume 71 102 m 3 /h (adjustable) Operation Touch free automatic. Safety Overheat temperature protection. Safety timer prevents continuous running. IP Rating IP23 Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) JETS10W 216 276 100 3.8

Hand Dryers Jetstream Arc 1.1 kw Automatic Hand Dryer Energy Efficient p. 68 Usage Suitable for many public washroom applications including restaurants, shops and shopping centres, office buildings, pubs, motorway services, factories and supermarkets. Features and Benefits Exceptional value for money High speed giving fast hand drying times Saves energy relative to traditional hand dryers from reduced drying times Modern stylish design Hygienic automatic operation reduces the risk of spreading germs Low 1.1 kw power rating Option to reduce power rating to 0.65 kw by switching off the heating element to increase energy efficiency Durable, easy clean, white ABS case Product Code Finish Power Sound Level (kw) (db) Dry Time (seconds) Air Speed (m/s) JET11W White 1.1 72 10-15 90

Hand Dryers Outer Casing White ABS casing Heating Element 450 W (on/off setting) Motor 650 W Carbon brush 24,000 27,000 RPM Current 5 amps Air Speed 90 m/s Installation Full fixing pack supplied. Cable entry bottom right at the base of the unit. Electrical Connection Installation must comply with current IEE Regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Class II p. 69 Operation Touch free automatic. Safety Overheat temperature protection. Safety timer prevents continuous running. IP Rating IPX1 Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) JET11W 260 250 180 3.2

Hand Dryers Tornado 2.3 or 2.5 kw Automatic Hand Dryer Traditional, Hand and Face Usage p. 70 Suitable for many public washroom applications including restaurants, shops and shopping centres, office buildings, pubs, motorway services, factories and supermarkets. Features and Benefits Traditional high powered hand dryer Hygienic automatic operation reduces the risk of spreading germs Easy clean stainless steel vandal resistant case Classic look Well suited to high traffic situations The chrome nozzle can be rotated for hand and face drying Product Code Finish Power Sound Level (kw) (db) Dry Time (seconds) Air Speed (m/s) TOR23W White 2.3 75 20 30 TOR23BSS Brushed SS 2.3 75 20 30 TOR25W White 2.5 75 20 30 TOR25BSS Brushed SS 2.5 75 20 30

Hand Dryers Outer Casing Stainless steel Heating Element 1800 W Motor 500 W Carbon brush 7,500 RPM Current 10 amps Operation Touch free automatic. Installation Full fixing pack supplied. Cable entry bottom left at the base of the unit. Electrical Connection Installation must comply with current IEE Regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Class I p. 71 Safety Overheat temperature protection. Safety timer prevents continuous running. IP Rating IPX1 Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) TOR23W 235 275 210 4.4 TOR23BSS 235 275 210 4.4 TOR25W 235 275 210 5.7 TOR25BSS 235 275 210 5.7

Hand Dryers Cyclone 1.6 kw Automatic Hand Dryer Traditional p. 72 Usage Suitable for a wide number of applications including schools, offices, restaurants and shops. Features and Benefits Traditional style hand dryer Low air speed makes the hand dryer suitable for young school children Stylish design in ivory white 1.6 kw power rating Metal vandal resistant case Product Code Finish Power Sound Level (kw) (db) Dry Time (seconds) Air Speed (m/s) HD1600 Ivory 1.6 73 30 12 White

Hand Dryers Outer Casing White metal case Heating Element 1500 W Motor 100 W Carbon brush 2850 RPM Current 7 amps Air Speed 12 m/s Installation Full fixing pack supplied. Cable entry bottom right at the base of the unit. Electrical Connection Installation must comply with current IEE Regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (1m). p. 73 Air Volume 181 m 3 /h Operation Touch free automatic. Safety Overheat temperature protection. Safety timer prevents continuous running. IP Rating IPX1 Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) HD1600 206 268 150 3.5

Hand Dryers Hurricane 1.8 kw Automatic Hand Dryer Traditional p. 74 Usage Suitable for a wide number of applications including schools, offices, restaurants and shops. Features and Benefits Traditional high powered hand dryer Low air speed makes the hand dryer suitable for young school children Stylish design in ivory white Hygienic automatic operation reduces the risk of spreading germs 1.8 kw power rating Metal vandal resistant case Product Code Finish Power Sound Level (kw) (db) Dry Time (seconds) Air Speed (m/s) HD1800 Ivory 1.8 73 25 18 White

Hand Dryers Outer Casing Die cast aluminium Enamel coated Heating Element 1600 W Motor 200 W Carbon brush 5600 RPM Current 8 amps Installation Full fixing pack supplied. Cable entry bottom right at the base of the unit. Electrical Connection Installation must comply with current IEE Regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. p. 75 Air Speed 18 m/s Air Volume 147 m 3 /h Operation Touch free automatic. Safety Overheat temperature protection. Safety timer prevents continuous running. IP Rating IPX1 Cable pre-wired (1m). Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) HD1800 263 245 195 3.4

Hair Dryers Topaz 1.5 kw Digital Hair Dryer p. 76 Usage Designed for hotels and similar light commercial applications. Not suitable for heavy usage applications such as public swimming baths and sports facilities. Features and Benefits Automatic hair dryer switching on when the handgrip is removed from the holder Ideal for hotel room en-suites where vandalism is unlikely Five selectable heat settings, 60 C default air temperature Constant temperature between 40 C and 80 C LCD display screen Extendable hose (up to 1.5m) Incorporates shaver socket IP24 splashproof Wall mounted Product Code Finish Power Heat Settings Air Volume (kw) (m 3 /h) HD15015 White 1.5 5 87

Hair Dryers Outer Casing White ABS Operation The hair dryer will start automatically when the nozzle is removed from the base and stop when it is replaced. Controls Temperature display ( C) with default setting 60 C. +/- controls allow the user to change the temperature. Installation Supplied with fixing brackets which must be used. Site according to the IP rating. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. p. 77 Unit automatically shuts off if left unattended. Current 6.5 amps Air Speed 17 m/s Safety Overheat temperature protection. Safety timer prevents continuous running (18 minutes). IP Rating IP24 Cable pre-wired (1.25m), entry in the middle of the base of the unit. Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) Excluding Hose 270 205 110 2.3 Including Hose 580 205 110 2.3

Hair Dryers Opal 1.4 kw Holster Style Hair Dryer p. 78 Usage Designed for hotels and similar light commercial applications. Not suitable for heavy usage applications such as public swimming baths and sports facilities. Features and Benefits Automatic hair dryer Ideal for hotel rooms where vandalism is unlikely Spring loaded start switch protects the dryer from unintended operation Three heat settings, 0.5, 1.0 and 1.4 kw Extendable lead (up to 1.4m) Wall mounted Product Code Finish Power Heat Settings Air Volume (kw) (m 3 /h) HD190I White 1.4 1 96

Hair Dryers Outer Casing White ABS Sound Level 60 db Safety Overheat temperature protection. Spring loaded start switch prevents unintended operation. p. 79 IP Rating IPX0 Installation Supplied with fixing brackets which must be used. Site according to the IP rating. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (0.6m), entry in the middle of the base of the unit. Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) HD190I 320 250 150 2.3

Hair Dryers Jade 0.7 kw Traditional Hair Dryer p. 80 Usage Designed for hotels and similar light commercial applications. Not suitable for heavy usage applications such as public swimming baths and sports facilities. Features and Benefits Automatic hair dryer switching on when the handgrip is removed from the holder Ideal for hotel room en-suites where vandalism is unlikely One heat setting Extendable hose (up to 1.4m) Incorporates shaver socket Wall mounted Product Code Finish Power Heat Settings Air Volume (kw) (m 3 /h) HD700 White 0.7 1 43

Hair Dryers Outer Casing White ABS Operation The hair dryer will start automatically when the nozzle is removed from the base and stop when it is replaced. Current 3 amps Air Speed 14 m/s Sound Level 75 db Safety Overheat temperature protection. Safety timer prevents continuous running (12 minutes). IP Rating IP21 Installation Supplied with fixing brackets which must be used. Site according to the IP rating. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (1.35m), entry at the top left of the unit. Approvals CE Standard Warranty 1 year parts or replacement warranty. p. 81 Product Code Height Width Depth Weight (kg) Excluding Hose 297 200 90 2.2 Including Hose 600 200 90 2.2

p. 82

Product Category Space Heating p. 83

Space Heating Accona Panel Heater 0.5, 1.0, 1.5 and 2.0 kw p. 84 Usage Ideal for a wide range of fixed installation heating applications in the home and office environment. Features and Benefits Timer Model Features Stylish curved design panel heaters Available in 0.5, 1.0, 1.5 and 2.0 kw 7 day LCD timer and standard non-timer models available (0.5 kw model timer only) Element on neon indicator Wall mounted secure bracket included Standard Model Features Mechanical thermostat and power on/off switch 7 day LCD electronic timer choose from pre-set schedules or create your own 2 user set temperature settings: peak for whilst the room is occupied and off peak (typically night or frost protection) Peak temperature range 21-30 C, off peak temperature range 5-17 C Time delayed start up and shut down Integrated child lock Product Code Power (kw) Timer Current (amps) AN500T 0.5 Yes 2.2 AN1000 AN1000T 1.0 No Yes 4.3 AN1500 AN1500T 1.5 No Yes 6.5 AN2000 AN2000T 2.0 No Yes 9

Space Heating Outer Casing Metal Controls Standard model adjustable thermostat and on/off switch. Timer model digital controls and screen. Louvres 0.5, 1.0 and 1.5 kw models have two columns of louvres. Installation Wall mounting kit included and must be used. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. p. 85 2.0 kw model has three columns of louvres. Safety Overheat temperature protection. IP Rating IPX0 Cable pre-wired (1.5m), white cable, entry to the top right of the unit. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) AN500T 440 444 98 4.4 AN1000 AN1000T 440 580 98 5.1 AN1500 AN1500T 440 700 98 6.2 AN2000 AN2000T 440 855 98 7.4

Space Heating Scirocco Convector Heater 2.0 kw p. 86 Usage Ideal for a wide range of fixed installation or portable heating applications in the home and office environment. Features and Benefits Floor standing or wall mountable Timer version includes a 24 hour segment timer Neon element on indicator Wall mounting kit and feet provided Thermostat 3 heat settings (0.75, 1.25 and 2.0 kw) Non-timer model available in 2 sizes, Y-classic and YM-modern Product Code Power (kw) Model Timer Current (amps) SC2000Y 2.0 Classic No 9 SC2000YM 2.0 Modern No 9 SC2000YST 2.0 Classic Yes 9

Space Heating Outer Casing Metal Controls All models: adjustable thermostat and on/off switch. Power setting switches. Timer model only: 24 hour segment timer, 15 minute interval time slots. Switch to select on all the time or timed operation. Push segments out for the time interval heater is to be timed on. Push segments in for the time interval heater is to be timed off. Installation Wall mounting kit included. Feet included for optional floor mounting. Electrical Connection Cable pre-wired (1.5m), white cable entry to the bottom left of the unit with a BS plug. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. p. 87 Safety Overheat temperature protection. IP Rating IPX0 Product Code Height Width Depth Weight (kg) SC2000Y 370 580 110 3.0 SC2000YM 335 530 110 3.0 SC2000YST 370 580 110 3.0 *Dimensions excluding feet. Including feet add 55mm to height and 40mm to depth

Space Heating Maestro Air Curtain 3.0 kw p. 88 Usage Over door fan heater designed for installation above doorways to reduce heat loss from buildings such as shops, restaurants and offices. Features and Benefits Stylish design over door fan heater 3 heat settings 1.5 and 3.0 kw, and fan only option Easy to install, with a robust fast fitting wall bracket Cable pre-wired Wall or ceiling mounted Neon power on indicator Product Code Power (kw) Timer Current (amps) MAC3X 3.0 No 13

Space Heating Outer Casing Powder coated steel Controls Power/fan on/off switch. Two temperature setting switches. Airflow 254 m 3 /h Sound Level 60 db Safety Overheat temperature protection. IP Rating IPX0 Installation Wall mounting kit included for wall or ceiling mounting. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a suitably rated isolating switch with a contact separation of at least 3mm in all poles. Cable pre-wired (1.5m), entry to the back of the unit located centrally. Class I p. 89 Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) MAC3X 205 630 105 5.2

Space Heating Novara PTC High Level Heater 2.0 kw p. 90 Usage This heater is typically used in commercial settings and is ideal for a wide range of fixed installation heating applications. Features and Benefits High level heater with positive temperature coefficient (PTC) element Fan assisted heating 3 heat settings cool, 1.0 and 2.0 kw Manual or remote control operation Remote control included (requires 2 x AAA batteries not included) Run on timer Neon power on indicator LED display indicating selected power and timer settings Wall mounting kit included Product Code Power (kw) Timer Current (amps) NV2000 2.0 Yes 9

Space Heating Outer Casing ABS Controls Power on/off switch. Timer selection switch. Timer runs for up to 7.5 hours in 0.5 hour intervals. Safety Overheat temperature protection. IP Rating IPX0 Installation Wall mounting kit included, 1.8m minimum height restriction. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (1.5m), black cable, entry to the top right of the unit. p. 91 Class II Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) NV2000 200 515 120 2.3

Space Heating Mistral Bathroom Fan Heater 1.8 kw p. 92 Usage Designed to cope with humidity and ideal for occasional heating of bathrooms. Features and Benefits Stylish slimline design bathroom, fan heater Splashproof Element on neon indicator Thermostat Cable pre-wired Wall mounted fittings included Removable and washable dust air filters Product Code Power (kw) Timer Current (amps) MS180 1.8 No 8

Space Heating Outer Casing Metal front plate and louvres with plastic back plate. Controls Thermostat control knob Installation Wall mounting kit included. Electrical Connection Installation must comply with current IEE regulations. Safety Overheat temperature protection. IP Rating IP24 The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. p. 93 Cable pre-wired (1.5m), entry to the back of the unit, located to the right. Class II Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) MS180 410 285 115 2.8

Space Heating Zephyr Downflow Fan Heater High Level 2.0 kw p. 94 Usage Ideal for providing occasional heating in small spaces such as bathrooms, kitchens and en suites. Features and Benefits Practical downflow fan heater Pull cord operation Element on neon indicator Wall mounted 2 power levels 1.0 and 2.0 kw set at installation In 2.0 kw mode thermostat reduces output to 1.0 kw when the room is warm and steps back up to 2.0 kw when required Internal thermostat set at installation Minimum installation height 1.8m from the floor Product Code Power (kw) Timer Current (amps) DF20 2.0 No 9

Space Heating Outer Casing ABS Controls Pull cord on/off operation. Neon indicator to show when in operation. Power level selection and thermostat under the main cover. Installation Wall mounting kit included and must be used. The unit has to be fitted at least 1.8m from the floor. Electrical Connection Installation must comply with current IEE regulations. p. 95 Safety Overheat temperature protection. IP Rating IP21 The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (0.9m), white cable, entry to the bottom right of the unit. Class II Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) DF20 240 235 125 1.4

Space Heating Arezzo Downflow Fan Heater Low Level 2.0 kw p. 96 Usage Ideal for providing occasional heating in small spaces such as bathrooms, kitchens and en suites. Features and Benefits Practical design downflow fan heater External thermostat Element on neon indicator Wall mounted 3 power levels fan only, 1.0 and 2.0 kw adjustable by a control to the front of the unit Power on/off control on the front of the unit Maximum installation height 1.8m from the floor Product Code Power (kw) Timer Current (amps) DF20LL 2.0 No 9

Space Heating Outer Casing ABS Controls Adjustable on/off thermostatic control. Installation Wall mounting kit included and must be used. Must be fitted no higher than 1.8m from the floor. Adjustable power level control knob. Safety Overheat safety protection. IP Rating IP23 Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. p. 97 Cable pre-wired (1.4m), white cable, entry to the bottom right of the unit. Class II Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) DF20LL 245 240 130 1.6

Space Heating Aztec Industrial Fan Heater 2.0 kw p. 98 Usage Portable heater for industrial buildings, workshops or use in a garage. Ideal for drying out newly plastered walls or as a source of heat for builders and trades people working indoors on new builds or refurbishment work. Features and Benefits Thermostatically controlled portable fan heater Heavy duty steel element Robust heavy duty construction 2.0 kw output 3 heat settings (1.0 kw/ 2.0 kw/ fan only) Integrated carry handle Product Code Power (kw) Timer Current (amps) IFH2000 2.0 No 9

Space Heating Outer Casing Stainless steel metal case and metal stand. Controls Function switch including off, cool blow, half heat and full heat output. Thermostat dial. Electrical Connection Supplied with a pre-wired (1.45m) black flex BS plug, cable entry to the right of the heater. Class I Approvals CE p. 99 Safety Overheat temperature protection. IP Rating IPX4 Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) IFH2000 293 245 225 8.1

Space Heating Fiji Fan Heater 2.0 kw p. 100 Usage Portable heater for home and office use. Features and Benefits Thermostatically controlled portable fan heater Stylish letterbox design 2.0 kw output 3 heat settings (1.0 kw/ 2.0 kw/ fan only) Neon element on indicator Overheat protection Product Code Power (kw) Timer Current (amps) FH-201Z 2.0 No 9

Space Heating Outer Casing Durable easy clean ABS Controls Function switch including off, cool blow, half heat and full heat output. Thermostat dial. Safety Overheat temperature protection. IP Rating IP20 Electrical Connection Supplied with a pre-wired (1.35m) white flex BS plug, cable entry to the back centre of the heater. Class II Approvals CE Standard Warranty 1 year parts or replacement warranty. p. 101 Product Code Height Width Depth Weight (kg) FH-201Z 130 270 280 1.4

Space Heating Riviera Oil Filled Radiator 0.7, 1.5 and 2.0 kw p. 102 Usage 0.7 kw model 1.5 and 2.0 kw model Portable heater for home and office use. Features and Benefits Oil filled radiator providing a silent gentle heating solution Neon element on indicator Moulded handle 0.7 kw model Single power setting (700 W), adjustable thermostatic control 7 fins Floor standing on stationary feet 2.0 kw model Three power settings (800, 1200 and 2000 W), adjustable thermostatic control 24 hour segment timer 9 fins Floor standing with smooth rolling castors for easy movement Tip over protection Cord cable storage 1.5 kw model Three power settings (600, 900 and 1500 W), adjustable thermostatic control 7 fins Floor standing with smooth rolling castors for easy movement Tip over protection Cord cable storage Product Code Power (kw) Timer Current (amps) RAD07Y 0.7 No 3 RAD15Y 1.5 No 6.5 RAD20TY 2.0 Yes 9

Space Heating * Line diagram for 1.5 and 2.0 kw models only. Outer Casing Metal Controls Thermostat dial. 2.0 kw model only: 24 hour segment timer with 15 minute interval time slots. Switch to select on all the time or timed operation. Push segments out for the time interval heater is to be timed on. Push segments in for the time interval heater is to be timed off. Electrical Connection Supplied with a pre-wired (1.9m) black flex BS plug, cable entry to the right of the heater. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. p. 103 Safety Overheat temperature protection. IP Rating IPX0 Product Code Height Width Depth Weight (kg) RAD07Y 380 310 100 3.6 RAD15Y 690 385 160 9.8 RAD20TY 690 465 160 11.8 *Depth excluding feet, depth including feet 240mm for 1.5 and 2.0 kw versions and 140mm for 0.7 kw version.

Space Heating Sahara Tubular Heater 1, 2, 3 and 4ft Usage p. 104 Ideal for heating a small space or area that needs to be protected from frost, tubular heaters can be used in a number of settings such as green houses, conservatories, workshops and caravans to provide a gentle background heat. Features and Benefits Energy efficient heater providing ambient heating and frost protection Helps reduce condensation and damp Gentle background heat IP55 waterproof Robust end fixing brackets (no flimsy plastic clips) Available in 1, 2, 3 and 4ft Guards are available for all sizes Quick and easy installation Easy to use Internal thermostat Product Code Size (ft) Power (W) Current (amps) TH01B 1 45 0.2 TH02B 2 80 0.35 TH03B 3 135 0.6 TH04B 4 180 0.8

Space Heating Outer Casing White coated steel tube, white plastic end caps and brackets. Controls None Safety Overheat temperature protection. IP Rating IP55 Installation Wall or floor mounting kit included and must be used. Electrical Connection Supplied with a pre-wired (1.3m) white cable BS plug, cable entry to the left of the unit. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. p. 105 Product Code Height Width Depth Weight (kg) TH01B 55 305 55 1.0 TH02B 55 610 55 1.5 TH03B 55 915 55 2.0 TH04B 55 1222 55 2.5

Space Heating Sahara Tubular Heater Guard 1, 2, 3 and 4ft p. 106 Usage Ideal for protecting tubular heaters which can get very hot to touch. Guards should be used to protect people or objects coming into contact with the hot surfaces. Features and Benefits Stylish curved design Available in 1, 2, 3 and 4ft Strong, robust and rigid Quick and easy installation Fittings provided Product Code THG01 THG02 THG03 THG04 Size (ft) 1 2 3 4

Space Heating Installation Easy to install with wall fixings included. Outer Casing Powder coated pressed steel Standard Warranty 1 year parts or replacement warranty. p. 107 Product Code Height Width Depth Weight (kg) THG01 220 305 100 0.6 THG02 220 610 100 0.9 THG03 220 915 100 1.3 THG04 220 1222 100 1.8

Space Heating Mojave Frost Protector 400 W p. 108 Usage Ideal for providing frost protection and low levels of heating in dry environments. Features and Benefits Compact low-powered convector heater Wall mounted bracket provided Simple and easy to use, with a single control Neon power on indicator Product Code Power (kw) Timer Current (amps) FW400H 0.4 No 1.7

Space Heating Outer Casing Metal with plastic end caps. Controls Adjustable, on/off thermostat Safety Overheat temperature protection. IP Rating IPX0 p. 109 Installation Wall mounting kit included and must be used. Electrical Connection Supplied with a pre-wired (1.5m) white cable BS plug, cable entry to the top right. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) FW400H 250 270 100 0.4

Space Heating Inca Frost Protector 200 W p. 110 Usage Provides low levels of heating for an area needing to be protected from frost, such as changing rooms, caravans, cloakrooms, workshops or conservatories. Features and Benefits Small and compact space saving vertical design Heavy duty steel element Thermostat Strong and durable To be used as a supplementary heat source Product Code Power (kw) Timer Current (amps) CH-200 0.2 No 0.9

Space Heating Outer Casing Powder coated steel with integral pressed steel guard. Controls Variable thermostat control knob. Safety Overheat temperature protection. IP Rating IPX4 Installation Wall mounting kit included and must be used. Electrical Connection Supplied with a pre-wired (1.5m) white cable BS plug, cable entry to the bottom right of the heater. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. p. 111 Product Code Height Width Depth Weight (kg) CH-200 300 125 70 0.4

Space Heating Towel Rails Space Heating Alize S Shaped Towel Rail 50 and 80 W p. 112 Usage For use in bathrooms, to provide dry, warm towels. Features and Benefits Traditional s shaped design Available in 50 W (chrome) and 80 W (white) Both models provide the same level of heat output Rapid heat up Robust mounting brackets included Lightweight and easy to install Product Code Power (W) Finish Current (amps) AL80SW 80 White 0.3 AL50SC 50 Chrome 0.2

Space Heating Towel Rails Space Heating Outer Casing AL80SW white enamel coated steel AL50SC chrome plated steel Controls None Safety Overheat temperature protection. IP Rating IPX4 Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. Cable pre-wired (1.5m), white cable entry to the bottom right of the towel rail. p. 113 Installation Wall mounting kit included and must be used. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) AL80SW 645 500 110 1.6 AL50SC 645 500 110 1.6

Space Heating Aquilo Ladder Style Towel Rail 100 W p. 114 Usage For use in bathrooms, to provide dry, warm towels. Features and Benefits Stylish and modern curved ladder design Stainless steel easy clean finish Rapid heat up Robust mounting brackets included Lightweight and easy to install Product Code Power (kw) Timer Current (amps) AQ100LC 100 No 0.4

Space Heating Outer Casing Stainless steel Controls None Safety Overheat temperature protection. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a double pole fused spur with a minimum break capacity of 13 amps. p. 115 IP Rating IPX4 Installation Wall mounting kit included and must be used. Cable pre-wired (1.5m), white cable entry to the bottom right of the towel rail. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) AQ100LC 860 530 110 2.9

Space Heating Sun Prince Quartz Indoor Halogen Infrared Heater 1.0, 1.5, 2.0, 3.0, 4.0 and 4.5 kw p. 116 Usage Ideal for heating applications in draughty or tall buildings such as garages, warehouses, factories and similar difficult to heat situations where convection heating would be impractical. Features and Benefits Allows heating of targeted areas Quartz halogen lamps operate at a very high temperature, converting almost all the electrical energy into short wavelength infrared radiation Stylish and robust construction Silent operation Heaters are single, double or triple chassis depending on number of lamps included (see table below) Lamps made from high temperature resistant quartz glass and last an average of 7000 hours Gold and ruby lamps available Instantaneous cost effective heating Wall mounted secure bracket included Lamps must not be handled with bare hands Suitable for indoor use only Product Code Power Lamp Colour* (kw) Lamp Qty x W SP1000HL SP1500HL SP2000HL SP3000HL SP4000HL SP4500HL 1.0 Gold 1 x L1000CGL 1.5 Ruby 1 x L1500CL 2.0 Gold 1 x L2000CGL 3.0 Ruby 2 x L1500CL 4.0 Gold 2 x L2000CGL 4.5 Ruby 3 x L1500CL *Gold lamps are available for SP1500H, SP3000H and SP4500H at an extra cost

Space Heating Heat Requirements Estimate total amount of wattage required using the formula below. Floor Area x Watts/M 2 Required (M 2 ) (See table below) Outer Casing Grey powder coated steel chassis, chrome plated safety guard. IP Rating IPX0 Installation Wall mounting kit included and must be used. Electrical Connection Installation must comply with current IEE regulations. Highly Insulated Insulated Un - Insulated Light Cladding Badly Insulated / Damp Heavy Work 150 175 200 250 300 Watts / M 2 Required Light Work 200 225 250 300 300 Spot Heating 250 250 275 300 300 The product should be connected to the fixed wiring of the property via a suitably rated isolating switch with a contact separation of at least 3mm in all poles. Optional soft start controllers are available. Class I Approvals CE Standard Warranty 1 year parts or replacement warranty (excluding lamps). p. 117 Product Code Height Width Depth Weight (kg) SP1000HL SP1500HL SP2000HL SP3000HL SP4000HL SP4500HL 198 474 141 3.09 198 474 141 3.09 198 474 141 3.09 398 474 141 5.35 398 474 141 5.35 598 474 141 7.57

Space Heating Quartz Controller Soft Start 3.0 kw p. 118 Usage Soft start heating controllers are designed to work alongside all makes of quartz halogen infrared heater. Features and Benefits Save energy by ensuring that halogen heaters are only on when you need them to be Can control up to 3.0 kw of Quartz heating load Protect switchgear from high inrush currents when the lamps are first switched on from cold PIR or Push button models available Weatherproof for outdoor use Run time adjustment from 1 99 minutes Temperature adjustment the unit will not operate if ambient temperature above threshold Easy to install Push Button model once activated will remain on for pre-set time or can be turned off by pushing the button PIR model automatically activated by motion from up to 5m and will remain on for the pre-set time, continuous movement will reset the timer Product Code Power (kw) Operating Temp ( C) Current (amps) QZC-PB3 Up to 3.0 kw 2 to 60 6 QZC-PIR3 Up to 3.0 kw 2 to 60 6

Space Heating Outer Casing ABS Switching Capacity 3.0 kw maximum 13 amps Current Consumption (control circuit) 2.0 W (10mA max) Lamp On-Time 1 99 minutes Installation Wall mounting kit included and must be used. Electrical Connection Installation must comply with current IEE regulations. The product should be connected to the fixed wiring of the property via a suitably rated isolating switch with a contact separation of at least 3mm in all poles. p. 119 Gland Diameter 20mm IP Rating IP65 Class I Approvals CE Standard Warranty 1 year parts or replacement warranty. Product Code Height Width Depth Weight (kg) QZC-PB3 100 100 60 0.5 QZC-PIR3 100 100 60 0.5

Space Heating Sun King Quartz Outdoor Halogen Infrared Heater 1.5 kw Usage Ideal for heating outdoor domestic and commercial applications, such as patios, beer gardens and smoking areas. p. 120 Features and Benefits Allows heating of targeted area Quartz halogen lamps operate at a very high temperature, converting almost all the electrical energy into short wavelength infrared radiation Stylish, lightweight aluminium construction Silent operation Lamps made from high temperature resistant quartz glass and last an average of 7000 hours Gold lamp Weatherproof for outdoor use Side reflectors for added heat output and efficiency Instantaneous cost effective heating Wall mounted secure bracket included Lamps must not be handled with bare hands Product Code Power (kw) Timer Current (amps) SK1500 1.5 Gold 1 x L1500A