MAXI-VENT Air Admittance Valve

MAXI-VENT Air Admittance Valve Manufacturer: Studor, Inc. Connec on Size: 3 or 4 Model #: MAXI VENT Item #: 20302 An air admittance valve shall be acceptable as a vent termination for any individual vent, common vent, circuit vent, loop vent, island fixture vent, vent stack or stack vent that is provided to prevent siphonage of a fixture trap. An air admittance valve can be used as an alternative to extending a vent through the roof (or sidewall) to the open atmosphere. A. The MAXI-VENT shall be located a minimum of 4 above horizontal branch drain or fixture drain being vented and 6 above the flood level of the highest fixture for stack venting. B. Each valve should be installed in an accessible location. A. The valve should be connected to the piping in accordance with the manufacturer s installation instructions. B. The valve should be installed in the vertical, upright position after rough-in and pressure testing of the DWV system. C. A minimum of one vent shall extend to the open atmosphere for every building drainage system. D. The valve should not be installed in a non-neutralized special (chemical) waste system or in supply and return air plenums. E. The valve may be installed on sewer ejectors, if installed according to engineer design and prior local code approval. F. For installation in areas with temperature range between 40 and 150 F. A. Screening on the inside and outside of the valve to protect the sealing membrane from insects and debris. B. Protective cover for additional insulation against extreme temperatures. C. Ability to divert condensation away from sealing membrane. D. Limited lifetime warranty for replacement of defective valves. A. Styrofoam cover B. ABS (acrylonitrile butadiene styrene) valve with silicone membrane C. Rubber connector ANSI/ASSE 1051 A&B 2009 single fixture and branch type AAVs ANSI/ASSE 1050 2009 stack type AAVs NSF Standard 14 2009 Plastics Piping System and Components International Plumbing Code (IPC) International Residential Code (IRC) Uniform Plumbing Code (UPC Section 301.2 Alternative Materials and Methods National Standard Plumbing Code (NSPC) - Appendix E National Plumbing Code of Canada (NPC) Listings: 5-1/4 MAXI VENT Horizontal Branch Size 3 20 4 160 Stack Size 4⅞ 3 4 Push-Fit Connector 3 72 4 500

MAXI-CAP Manufacturer: Studor, Inc. Item #: 20398 The MAXI-CAP can be installed on MAXI-VENT in outdoor installations to protect MAXI-VENTs from damaging UV Rays and extreme temperatures. MAXI CAP 6 ⅞ A. Fits over the MAXI-VENT and styrofoam cover. If desired, paint cap prior to installation. B. Attach syrofoam to cap of valve with double-sided adhesive. C. Attach metal cap to styrofoam with double-sided adhesive. D. Ensure that one open vent pipe is maintained. 3⅝ A. Spun Aluminum Cap B. 2 pieces of double-sided adhesive Double side adhesive

MINI-VENT Air Admittance Valve Manufacturer: Studor, Inc. Connec on Size: 1 1/2 2 Model #: MINI VENT Item #: 20301 (PVC Connector); 20300 (ABS Connector) An air admittance valve shall be acceptable as a vent termination for any individual vent, common vent, circuit vent, loop vent, island fixture vent, vent stack or stack vent that is provided to prevent siphonage of a fixture trap. An air admittance valve can be used as an alternative to extending a vent through the roof (or sidewall) to the open atmosphere. A. The MINI-VENT shall be located a minimum of 4 above the horizontal branch drain or fixture drain being vented and a minimum of 6 above the flood level of the highest fixture for stack venting. B. Each valve should be installed in an accessible location. A. The valve should be connected to the piping in accordance with the manufacturer s installation instructions. B. The valve should be installed in the vertical, upright position after rough-in and pressure testing of the DWV system. C. A minimum of one vent shall extend to the open atmosphere for every building drainage system. D. The valve should not be installed in non-neutralized special (chemical) waste system or in supply and return air plenums. E. The valve may be installed on sewer ejectors, if installed according to engineer design and prior local code approval. F. For installation in areas with temperature range between 40 and 150 F. A. Screening on the inside and outside of the valve to protect the sealing assembly from insects and debris. B. Protective cover for the air intake and additional insulation against extreme temperatures. C. Ability to divert condensation away from sealing membrane. D. Limited lifetime warranty for replacement of defective valves. A. Polystyrene B. ABS (acrylonitrile butadiene styrene) valve with silcone membrane C. ABS or PVC (adaptor) ANSI/ASSE 1051 A&B single fixture and branch type AAVs ANSI/ASSE 1050 stack type AAVs NSF Standard 14 Plastics Piping System and Components 2⅝ MINI VENT Protec ve Cover 2 Adaptor 1 ½ NPT Fits 1 ½ or 2 pipe sizes International Plumbing Code (IPC) International Residential Code (IRC) Uniform Plumbing Code (UPC Section 301.2 Alternative Materials and Methods National Standard Plumbing Code (NSPC) Appendix E National Plumbing Code of Canada (NPC) Listings: Horizontal Branch Size 1 1/2 3 2 6 3 20 4 160 Stack Size 1 1/2 8 2 24

REDI-VENT Air Admittance Valve Manufacturer: Studor, Inc. Connec on Size: 1 1/2 or 2 Model #: REDI VENT Item #: 20346 (PVC Connector); 20349 (ABS Connector) An air admittance valve shall be acceptable as a vent termination for any individual vent, common vent, circuit vent, loop vent and island fixture vent that is provided to prevent siphonage of a fixture trap. An air admittance valve can be used as an alternative to extending a vent through the roof (or sidewall) to the open atmosphere. A. The REDI-VENT shall be located a minimum of 4 above the horizontal branch drain or fixture drain being vented and a minimum of 6 above the flood level of the highest fixture for stack venting. B. Each valve should be installed in an accessible location. A. The valve should be connected to the piping in accordance with the manufacturer s installation instructions. B. The valve should be installed in the vertical, upright position after rough-in and pressure testing of the DWV system. C. A minimum of one vent shall extend to the open atmosphere for every building drainage system. D. The valve should not be installed in non-neutralized special (chemical) waste system or in supply and return air plenums. E. For installation in areas with temperature range between 40 and 150 degrees F. A. Screening on the inside and outside of the valve to protect the sealing assembly from insects and debris. B. Will vent up to 20 DFUs on a horizontal branch. C. Limited lifetime warranty for replacement of defective valves. A. ABS (acrylonitrile butadiene styrene) valve with silicone membrane B. ABS or PVC (adaptor) 2⅝ REDI VENT 2 Adaptor 1 ½ NPT Fits 1 ½ or 2 pipe sizes ANSI/ASSE 1051 2009 single fixture and branch type AAVs ANSI/ASSE 1050 2009 stack type AAVs NSF Standard 14 2009 Plastics Piping System and Components Horizontal Branch Size International Plumbing Code (IPC) International Residential Code (IRC) Uniform Plumbing Code (UPC Section 301.2 Alternative Materials and Methods National Standard Plumbing Code (NSPC) Appendix E National Plumbing Code of Canada (NPC) 1 1/2 3 2 6 3 20 4 20 Stack Size 1 1/2 8

AAV-TEE Redi Vent Air Admittance Valve with Tubular Adaptor Manufacturer: Studor, Inc. Connec on Size: 1½ Model #: AAV TEE Item #: 20391 An air admittance valve shall be acceptable as a vent terminal for any individual vent, common vent, circuit vent, loop vent and island fixture vent that is provided to prevent siphonage of a fixture trap. An air admittance valve can be used as an alternative to extending a vent through the roof (or sidewall) to the open atmosphere. A. The air admittance valve shall be located a minimum of 4 above the horizontal branch drain or fixture drain being vented. B. Each valve should be installed in an accessible location. A. The valve should be connected to the piping in accordance with the manufacturer s installation instructions. B. The valve should be installed in the vertical, upright position after rough-in and pressure testing of the DWV system. C. A minimum of one vent shall extend to the open atmosphere for every building drainage system. D. The valve should not be installed in non-neutralized special (chemical) waste system or in supply and return air plenums. E. For installation in areas with temperature range between 40 F and 150 F. A. Screening on the inside and outside of the valve to protect the sealing assembly from insects and debris. B. Will vent up to 20 DFUs on a horizontal branch C. Limited lifetime warranty for replacement of defective valves. A. ABS (acrylonitrile butadience styrene) valve with silicone membrane B. Tubular adaptor (Polypropylene) ANSI/ASSE 1051-2009 single fixture and branch type AAVs ANSI/ASSE 1050-2009 stack type AAVs NSF Standard 14-2009 Plastics Piping System and Components International Plumbing Code (IPC) International Residential Code (IRC) Uniform Plumbing Code (UPC Section 301.2 Alternative Materials and Methods National Standard Plumbing Code (NSPC) Appendix E National Plumbing Code of Canada (NPC) Tubular Adaptor 4 1/4 REDI VENT 2 Listings: 2⅝

Trap-Vent Manufacturer: Studor, Inc. Connec on Size: 1 1/4 or 1 1/2 Model #: Trap Vent Item #: 20395 or 20396 The compact Studor Trap-Vent is a combined trap with a 2 water seal, and an integral AAV, reducing the need for secondary ventilating and replacing conventional P-traps. The valve within the Trap-Vent opens and admits fresh air when the negative pressure occurs from a fixture discharging into the system. This equalizes the pressure within the system and protects the trap seal. When the flow stops, the valve closes by gravity, preventing any transmission of sewer gas. The Trap-Vent can support a twenty foot head pressure. A. The Trap-Vent is for use on a lavatory, water cooler or sinks that do not receive a discharge from any appliance. Trap-Vent is rated up to 6 DFUs on a horizontal wet vent. B. Note, Trap-Vent cannot be installed on kitchen sinks, laundry tubs or a sink that receives a discharge from any kind of appliance. A. The Trap-Vent should be connected to the piping in accordance with the manufacturer s installation instructions. B. The Trap-Vent should be installed in the vertical, upright position after rough-in and pressure testing of the DWV system. C. A minimum of one vent shall extend to the open atmosphere for ever building drainage system. D. The Trap-Vent should not be installed as a vent terminal for any special (chemical) waste system or in supply and return air plenums. E. For installation in areas with temperature range between +32 F and +150 F. Accessories: A. White Cladding is available for a designer finish. The cladding simply snaps over the Trap-Vent Body. A. Body: UV Stabilized ABS (acrylonitrile butadiene styrene) B. Membrane: Synthetic Rubber Trap-Vent is for use on a lavatory, water cooler or on sinks that do not receive a discharge from any appliance. Trap-Vent is rated up to 6 DFU on a horizontal wet vent. Trap--Vent cannot be installed on kitchen sinks, laundry tubs, or a sink that receives discharge from any kind of appliance. Trap-Vent must be installed in a vertical position in an accessible location which permits free movement of air into the valve. Do not use where pumps or pressurized flushing devices are used. Do not install Trap-Vent where it could be subject to subfreezing temperatures or temperatures exceeding 150 F. Please follow all instructions carefully during installation. This devise is not a substitute for ALL conventional venting situations. Listings are subject to change without notice. Codes compliance will vary per State and Municipality, please verify with your local code officials before installing. Tailpieces and adapters were not tested or listed by NSF International for this production location. Product can also come with white cladding model, 20496. 500 Distribu on Parkway, Collierville, TN 38017 800 888 8312 Fax: 901 853 5008 www.ipscorp.com

Trap-Vent Manufacturer: Studor, Inc. Connec on Size: 1 1/4 or 1 1/2 Model #: Trap Vent Item #: 20395 or 20396 B A C Cladding E D M L F I N H J K G O P Q R 1 1/4 outlet pipe U T S 1 1/2 outlet pipe 500 Distribu on Parkway, Collierville, TN 38017 800 888 8312 Fax: 901 853 5008 Dimension Inches A 1 1/4 B 5/8 C 2 D 4 1/16 E 2 7/8 F 1 7/16 G 5 1/16 H 1 3/4 I 1 1/16 J 21/8 1 1/4 1 1/2 L 3 3/16 M N O 5 3/16 P 11/2 Q Ø1.25 R 8 S Ø1.5 T Ø1.625 U 8 K (outlet option)

Air Admittance Valve Recess Box D C H A B E F G I SPECIFICATION Studor offers a recess box and grille ideally suited for in-wall installation of its Mini-vent, Redi-Vent, and Tec-Vent Air Admittance Valves. The recess box includes an integral 1 1/2 threaded connection with integral test cap for easy installation as well as esthetically pleasing solution while providing code required accessibility to the valve. Recess box shall be connected to 1 1/2 or 2 PVC or ABS DWV piping. The recess box shall be listed to IAPMO or ICC-ES standards and include a one-piece snap-on grille as manufactured by IPS Corporation. DIMENSIONS Recess Box Snap On Grille A Width (w/flanges) 5 7/8" G Width 8" B Rough In Width 4 1/8" H Height 6 5/8" C Overall Height 7 1/8" I Flange Depth 7/8" D Rough In Height 5 1/2" E Depth 3 5/8" F Depth (from Flanges) 3 1/32" Product # Description 20380 Mini Recess Box 20381 Mini Recess Box with Redi Vent AAV 500 Distribu on Parkway, Collierville, TN 38017 TEL: 800 888 8312 Fax: 901 853 5008 www.ipscorp.com

P.A.P.A. Positive Air Pressure Attenuator Manufacturer: Studor, Inc. Connec on Size: 3 spigot Model #: P.A.P.A. Item #: 20357 The P.A.P.A. device is the perfect compliment to Studor Air Admittance Valves (AAVs). Together they form the Studor Single Pipe System (SSPS), a total solution to building venting requirements. The Studor AAVs deal with the negative pressure in the system while the P.A.P.A. effectively deals with the positive pressure transients. The combination of the two maintains the perfect system balance quickly and efficiently throughout the system preventing siphonage and blowing of traps. For commercial use in multi-story buildings The P.A.P.A. can be used in conjunction with a conventional DWV system or in a system with AAVs. The P.A.P.A. device shall be connected to the piping in accordance with the manufacturer s installation instructions. 29 ½ 7 ⅞ A. One gallon capacity B. Expandable capacity up to four gallons; series assembly provides additional capacity C. Operating temperatures 40 to 150 F. D. Rated for 5 PSI E. Limited lifetime warranty for replacement of defective devices. A. PVC housing B. Butylene bag 3 spigot Performance Standard: ASSE 1030 2009 Performance Requirements for Positive Pressure Reduction Devices for Sanitary Drainage Systems. International Plumbing Code (IPC) - Section 105.2 Alternate Materials, Methods and Equipment Uniform Plumbing Code (UPC) Section 301.2 Alternative Materials and Series Assembly Maximum number of units: 4 Air Capacity US Gallons 1 unit 1 2 units 2 3 units 3 4 units 4

TEC-VENT Air Admittance Valve Manufacturer: Studor, Inc. Connec on Size: 1 1/2 Model #: TEC VENT Item #: 20344 An air admittance valve shall be acceptable as a vent termination for any individual vent, common vent, circuit vent, loop vent, and island fixture vent that is provided to prevent siphonage of a fixture trap. An air admittance valve can be used as an alternative to extending a vent through the roof (or sidewall) to the open atmosphere. A. The TEC-VENT shall be located a minimum of 4 above the horizontal branch drain or fixture drain being vented and a minimum of 6 above the flood level of the highest fixture for stack venting. B. Each valve should be installed in an accessible location. A. The valve should be connected to the piping in accordance with the manufacturer s installation instructions. B. The valve should be installed in the vertical, upright position after rough-in and pressure testing of the DWV system. C. A minimum of one vent shall extend to the open atmosphere for every building drainage system. D. The valve should not be installed as a vent terminal for any special (chemical) waste system. E. The valve may be installed on sewer ejectors or in supply and return air plenums, if installed according to engineer design and prior local code approval. F. For installation in areas with temperature range between 40 and 150 F. G. Not for installation in non-neutralized special (chemical) waste systems. A. Screening on the inside and outside of the valve to protect the sealing membrane from insects and debris. B. Ability to divert condensation away from sealing membrane. C. UV rated. D. Limited lifetime warranty for replacement of defective valves. Flame-retardant polycarbonate resin valve with silicone membrane. ANSI/ASSE 1051 Single fixture and branch type AAVs ANSI/ASSE 1050 Stack type AAVs NSF Standard 14 Plastics Piping System and Components UL Standard 2043 Interna onal Plumbing Code (IPC) Interna onal Residen al Code (IRC) Uniform Plumbing Code (UPC Sec on 301.2 Alterna ve Materials and Methods Na onal Standard Plumbing Code (NSPC) Appendix E Na onal Plumbing Code of Canada (NPC) List- ings: AIR ADMITTANCE VALVES DISCRETE PRODUCTS INSTALLED IN AIR HANDLING SPACE (PLENUMS) As to Heat Release and Smoke Op cal Density Only 9DA2 Horizontal Branch Size 1 1/2 3 2 6 3 20 4 160 Stack Size 1 1/2 8 2 24

CHEM-VENT Air Admittance Valve Manufacturer: Studor, Inc. Connec on Size: 1 ½ Model #: CHEM VENT Item #: 20345 The CHEM-VENT air admittance valve shall be acceptable as a vent terminal for a nonneutralized special waste system to prevent siphonage of the fixture trap. A. The CHEM-VENT should be located a minimum of 4 above the horizontal branch drain or fixture drain being vented. B. Each valve should be installed in an accessible location. A. The valve should be connected to the piping in accordance with the manufacturer s installation instructions. B. The valve should be installed in the vertical, upright position after rough-in and pressure testing of the DWV system. C. A minimum of one vent shall extend to the open atmosphere for every building drainage system. D. The valve should not be installed in supply and return air plenums. E. For installation in areas with temperature range between 40 F and 212 F. F. The valve can be installed in non-neutralized chemical waste systems provided the system is designed by a design professional. A. Ball valve sealing assembly B. Will vent up to 6 DFUs C. Designed for chemical waste systems D. Screening on the inside and outside of the valve to protect the sealing assembly from insects and debris E. Limited lifetime warranty for replacement of defective valves. A. Flame Retardant Polypropylene (conforming to D-4101) B. O-ring is made from Ethylene Propylene Diene Monomer (EPDM) ASSE 1049 Performance Requirements for Individual and Branch Type Air Admittance Valves for Chemical Waste Systems 6 3/16 CHEM VENT 2 3/16 1½ Sch. 40 International Plumbing Code (IPC) Uniform Plumbing Code (UPC Section 301.2 Alternative Materials and Methods National Standard Plumbing Code (NSPC) Appendix E Listings: Horizontal Branch Size 1 1/2 3 2 6

MAXI-FILTRA Air Admittance Valve Manufacturer: Studor, Inc. Connec on Size: 3 or 4 Model #: MAXI-FILTRA Item #: 20297 Item #: 20700, Replacement Cartridge The MAXI-FILTRA is a two way vent, which filters air in both directions. It is designed for outdoor use only on septic tanks and lift stations. It is UV rated and comes with a replaceable carbon filter to eliminate bad odors. MAXI-FILTRA 4⅞ Buildings connected to the main sewer can also benefit from the use of the MAXI- FILTRA, but Studor technical department must be contacted so that installation feasibility can be determined. The MAXI-FILTRA, as part of the complete STUDOR System eliminates sewer gases from entering buildings or polluting the surrounding areas. It can also be retro-fitted in an existing plumbing system provided that all design and installation criteria are met. 5-1/4 A. The MAXI-FILTRA is for outdoor use only A. Install filter after drainage and waste system has been roughed in and tested. B. Install valves in accessible locations to allow for filter cartridge replacement. C. Connect valves to piping in accordance with manufacturer s instructions. D. Do not install valves on chemical waste systems or in supply and return air plenums. E. The MAXI-FILTRA can be installed vertically or horizontally F. The MAXI-FILTRA contains a replaceable carbon filter cartridge which can last up to 2 years. 3 A. UV inhibitor in resin compounds for exposure to sunlight B. Active Charcoal Filter replaceable cartridge A. ABS (acrylonitrile butadiene styrene) B. Active Charcoal Filter replaceable cartridge C. Rubber connector 4 Push-Fit Connector 500 Distribu on Parkway Collierville, TN 38017 800-888-8312 901-853-5001 FAX: 901-853-5008 www.ipscorp.com