REMOTE OVERVIEW Your idatastart remote start system may include one or both long-range remotes listed below. Please take a moment to familiarize yourself with their general features. REMOTE MODEL Related Product(s) Technology Max. Range TR2350AC RF2352A, HC2351AC (Discontinued), HC2352AC FM 2-WAY 3000 feet Buttons 5 Transmit Confirmation (TX) Receive Confirmation (RX) Batteries Required Avg. Battery Life Warranty Top LED Button LED + Chime 1 x CR2450 6-12 months 1 year REMOTE S & S Thanks to their multiplexing technology, idatastart remotes can pack over 30 functions using only 5 buttons. In order to get the most out of your remotes, please take a moment to get acquainted with the following functions 2018-06-30 Automotive Data Solutions Inc. 1/15
below: NOTES: 1. All functions must be enabled by an Authorized Dealer during installation to be functional on remote 2. Non-highlighted icons = Press & release button 3. Highlighted (grey) icons = Press & hold button for 2.5 seconds 4. Coma (,) between icons = Press buttons one after the other 5. Plus (+) between icons = Press buttons together 6. Timeout between each button press = 3 seconds 7. Function* = Available in 2nd Car Mode LOCK AND ARM* Lock & Arm Secures your vehicle by locking the doors and arming the alarm. 1 chime + 1 flash UNLOCK AND DISARM* Unlock & Disarm Accesses your vehicle by unlocking the doors and disarming the alarm. 2 chimes + 2 flashes QUERY* Query* Queries vehicle and vehicle battery voltage and interior temperature. PANIC* 2018-06-30 Automotive Data Solutions Inc. 2/15
Panic* Triggers the panic siren. 1 chime + 1 flash AUX 5* AUX 5* To be completed by Authorized Dealer if applicable TRUNK RELEASE Trunk Release* Releases the trunk or hatch. ENGINE START/STOP* Engine Start/Stop* Starts and stops the engine. 4 chimes + 4 flashes (Button LEDs will also flash intermittently while engine is running) AUX 1 AUX 1 To be completed by Authorized Dealer if applicable AUX 2 2018-06-30 Automotive Data Solutions Inc. 3/15
AUX 2 To be completed by Authorized Dealer if applicable AUX 3 AUX 3 To be completed by Authorized Dealer if applicable AUX 4 AUX 4 To be completed by Authorized Dealer if applicable 2ND CAR MODE 2nd Car Mode * Controls two idatastart-equipped vehicles using one remote. Works with all functions marked with an asterisk (*). SILENT LOCK* Silent Lock* Disables the vehicle s horn and alarm siren. SILENT UNLOCK* 2018-06-30 Automotive Data Solutions Inc. 4/15
Silent Unlock* Disables the vehicle s horn and alarm siren. VALET MODE ON/OFF Valet Mode ON/OFF Turns off remote start and security features when servicing your vehicle or valet parking. Keyless entry features remains functional. 1 chime ON 2 chimes OFF RUNTIME EXTEND Runtime Extend Seamlessly extends your engine runtime without restarting your vehicle. MUTE ON/OFF Mute ON/OFF Disables the vehicle s horn and alarm siren even when alarm is triggered. Remote will still receive alarm notification. 1 chime ON 2 chimes OFF IGNITION LOCK ON/OFF 2018-06-30 Automotive Data Solutions Inc. 5/15
Ignition Lock ON/OFF Automatically locks doors when engine is running. 1 chime ON 2 chimes OFF PASSIVE LOCK ARM ON/OFF Passive Lock & Arm ON/OFF Automatically locks and arms your vehicle 60 seconds after you unlock it. 1 chime ON 2 chimes OFF TURBO ON/OFF Turbo ON/OFF Cools down your turbo before turning the engine off. Programmable runtime from 30 seconds to 4 minutes. 1 chime ON 2 chimes OFF WHEATER START ON/OFF Weather Start ON/OFF Sets your vehicle to automatically remote start every 2, 3 or 4 hours (programmable) or from a temperature sensor sold separately. 1 chime ON 2 chimes OFF LOCK REMOTE 2018-06-30 Automotive Data Solutions Inc. 6/15
Lock Remote Disables all functions on your remote. 1 chime + 1 flash UNLOCK REMOTE ON/OFF Unlock Remote ON/OFF Enables all functions on your remote. 2 chimes + 2 flashes MUTE REMOTE ON/OFF Mute Remote ON/OFF Disables the chime when pressing any button on your remote. 1 chime ON 2 chimes OFF PROGRAMMING A NEW REMOTE Are you replacing a lost or damaged remote or simply adding an extra remote to your idatastart system? Please take note of the following: 1. A functional idatastart system must already be installed in your vehicle. 2. All new remotes must be installed by an idatastart Authorized Dealer. 3. A maximum of 4 remotes can be programmed to your idatastart system. REPLACING REMOTE BATTERIES Follow the steps below to replace the batteries in your idatastart remotes*. 2018-06-30 Automotive Data Solutions Inc. 7/15
1. Insert a 25 cent coin into the hollow corner of your idatastart remote. 2. Gently twist the coin until the casing pops open. 3. Use your coin to pry open the rest of the case perimeter. 4. Carefully remove the circuit board from the case. 5. Slide the old battery out of its enclosure and replace with the new battery. 6. Carefully replace the circuit board into bottom half of the casing. 7. Snap top and bottom casings back together using your hands. REMOTE STARTING FROM FACTORY KEY FOB Your idatastart system may enable remote engine start by performing one of the following button sequences on your factory key fob: Press on Press on FUNCTION Start engine Stop engine OR Press on Press on FUNCTION Start engine Stop engine NOTE: This feature may not be supported on some vehicles. If supported, the chosen button sequence will be communicated to you by your idatastart Authorized Dealer at the time of installation. The remote start range will be equal to your factory key fob s door lock range. 2018-06-30 Automotive Data Solutions Inc. 8/15
ADJUSTING ENGINE RUNTIME SETTINGS Once remote started from your factory key fob or long-range remote, your vehicle will run for the programmed runtime setting. The default runtime is 15 minutes but it can also be programmed for 3, 5, 10, 25, 30 or 35 minutes. If you wish to change your remote start runtime setting, contact your idatastart Authorized Dealer. KEY TAKEOVER FOLLOWING REMOTE START The key takeover procedure ensures that your engine does not shut down upon entering the vehicle, during the programmed remote start runtime. To prevent your vehicle from shutting down, complete the steps below within the programmed delay time (45 seconds, 90 seconds, 3 minutes or 4 minutes): For Standard Key Vehicles 1. Unlock and enter vehicle 2. Close doors 3. Insert key into ignition and turn ignition to ON position 4. Press foot brake For Push-To-Start Vehicles 1. Unlock and enter vehicle with valid smartkey 2. Close doors 3. Press foot brake NOTE: This feature may not be supported on some vehicles. If available, the programmed key takeover delay time will be communicated to you by your idatastart Authorized Dealer at the time of installation. WHEN SERVICING YOUR VEHICLE To ensure safety during vehicle servicing, the remote starter must be placed in Valet Mode. The Valet Mode will disable remote start functionality. To activate or deactivate the Valet Mode, follow the instructions below: With Vehicle Key: Cycle ignition OFF/ON 2x rapidly, then press brake 3x. 2018-06-30 Automotive Data Solutions Inc. 9/15
FUNCTION # OF PARKING LIGHT FLASHES Valet Mode ON 1 Valet Mode OFF 2 With idatastart Remote: Turn ignition ON, then press FUNCTION # OF PARKING LIGHT FLASHES Valet Mode ON 1 Valet Mode OFF 2 With idatastart Antenna: Turn ignition ON, then press & hold button for 5 seconds FUNCTION # OF PARKING LIGHT FLASHES Valet Mode ON 1 Valet Mode OFF 2 REMOTE START TROUBLESHOOTING If your idatastart remote fails to start the vehicle, the parking lights will flash three times immediately, then flash a number of times according to the errors below: 2018-06-30 Automotive Data Solutions Inc. 10/15
# OF PARKING LIGHT FLASHES DIAGNOSTIC SOLUTION 3 + 1 Need to learn tach 3 + 2 Key in ignition at ON position Remove key from ignition 3 + 3 Door is open Close door 3 + 4 Trunk is open Close trunk 3 + 5 Brake is detected Release brake 3 + 6 Hood is open Close hood 3 + 7 Reservation not done (manual only) Perform reservation procedure 3 + 8 Tach failure Contact Authorized Dealer 3 + 9 VSS detected (vehicle in movement) Contact Authorized Dealer 3 + 10 System is in Valet Mode Exit Valet Mode 3 + 11 Can communication failure Contact Authorized Dealer 3 + 12 Can communication failure Contact Authorized Dealer 3 + 13 Bypass error Contact Authorized Dealer 3 + 14 No Pitstop or Takeover available Contact Authorized Dealer 3 + 15 Module overheat protection Contact Authorized Dealer VEHICLE SHUTDOWN TROUBLESHOOTING If the remote start sequence has been completed and the vehicle shuts down, the vehicle s parking lights will flash 4 times immediately, then flash a number of times according to the errors below: 2018-06-30 Automotive Data Solutions Inc. 11/15
# OF PARKING LIGHT FLASHES DIAGNOSTIC SOLUTION 4+1 No engine rev detected Contact Authorized Dealer 4+3 Brake detected Release brake 4+4 Hood open detected Close hood 4+5 Engine revving over 3000 RPM Check your accelerator pedal 4+6 Glow plug error Contact Authorized Dealer 4+7 Vehicle speed sensor error Contact Authorized Dealer 4+8 Check Engine light detected Clear Check Engine code 4+9 Low fuel detected Add fuel 4+10 Door open detected Close door 4+11 CAN communication failure Contact Authorized Dealer 4+12 Key synchronisation failure Contact Authorized Dealer 4+13 Bypass error Contact Authorized Dealer 4+14 No Pitstop or Takeover available Contact Authorized Dealer 4+15 Module overheat protection Contact Authorized Dealer LIMITED LIFETIME WARRANTY Automotive Data Solutions Inc. ( ADS ) warrants to the original purchaser of the idatastart product that the following components product shall be free of defects in material and workmanship under normal use and circumstances: Control module and installation harnesses For as long as the original purchaser owns the vehicle in which it was originally installed. Remote transmitters and antenna For the period of one (1) year from the date of original installation. Excludes battery replacement. In the event of any product malfunction during the Warranty period, the original purchaser must return to the Authorized Dealer where it was originally purchased with the original proof of purchase. If a malfunction is detected, the Authorized Dealer will elect to repair or replace the product at its discretion. Labor costs may be applicable and are at the discretion of the Authorized Dealer. 2018-06-30 Automotive Data Solutions Inc. 12/15
The Limited Lifetime Warranty is automatically void if: An original proof of purchase is not provided when servicing the product during the warranty period; The date code and/or serial number is defaced, missing, or altered; The idatastart product is transferred to another vehicle; The vehicle in which the product was originally installed is transferred to a new owner. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the installation or operation of an idatastart product. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. IC STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following 2018-06-30 Automotive Data Solutions Inc. 13/15
two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-3 (B)/NMB-3(B) SAR INFORMATION STATEMENT Your wireless REMOTE CAR STARTER (TWO WAY) is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless REMOTE CAR STARTER (TWO WAY) employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 4.0 W/kg. Tests for SAR are conducted with the REMOTE CAR STARTER (TWO WAY) transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the REMOTE CAR STARTER (TWO WAY) while operating can be well below the maximum value. This is because the REMOTE CAR STARTER (TWO WAY) is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a REMOTE CAR STARTER (TWO WAY) model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model REMOTE CAR STARTER (TWO WAY) when tested for use at the extremity is 0.030W/Kg. While there may be differences between the SAR levels of various REMOTE CAR STARTER (TWO WAY) and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model REMOTE CAR STARTER (TWO WAY) with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model REMOTE CAR STARTER (TWO WAY) is on file with the FCC and can be found under the Display Grant section of 2018-06-30 Automotive Data Solutions Inc. 14/15
http://www.fcc.gov/oet/fccid after searching on 2AEPJ-TR3450AF. Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Association (CTIA) website at http://www.wow-com.com.* In the United States and Canada, the SAR limit for REMOTE CAR STARTER (TWO WAY) used by the public is 4.0 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements. This device complies with FCC and ISED 10-g extremity SAR requirements when the device is used at 0 mm separation. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. 2018-06-30 Automotive Data Solutions Inc. 15/15