ASKO Laundry Care W6324 W6324W LINE SERIES TM CLASSIC Type: Front-load, Family-size washer, ADA Compliant Colors: White (W) PROGRAMS Sani, White, Color, Quick, PermaPress, Wool / Handwash OPTIONS Up to 1200 RPM speed, 3 Temperatures up to 140ºF, Super rinse (up to 7 rinses), High wash water level CAPACITY UltraCare TM family-size 2.12 cu. ft. TECHNOLOGY Line Series TM Classic LCD display with SmoothDial TM technology, Internal water heater produces optimal temperatures during main wash, Automatic load balancing, Electronic automatic door latch, Thermistor electronic sensor ensures accurate wash temperatures within +/-1ºF, and Aqua Block System CONSTRUCTION New ActiveDrum TM, Quattro TM commercial design, SmartSeal TM door gasket, Stainless Steel inner/outer drum, Heavy duty life-tested motor, Galvanized steel base, Cast iron counter balance weights and rear flywheel. Noise level 54 db(a)wash / 74 db(a) spin W6324W & T744CW Asko Appliances, Inc PO BOX 940609 Plano Texas 75094 www.askousa.com
Planning & Design: Family-Size Washers Line Series Classic W6324 Unit Dimensions Height: 33 ½ 34 ½ 851 876 mm Depth: 23 7 /8 606 mm Depth w/door open: 36 914 mm Weight: 172 lbs 78 kg Technical Data Supply voltage Single-phase 208-240 V, 60 Hz Water Pressure 15 146 psi Max Wattage 2200 W Power cord 220 V, 20 Amp (attached) 23 5 /8 36 (914 mm) 23 7 /8 (606 mm) 4 ¾ (120 mm) 3 1 /8 (80 mm) 1 ¾ (44 mm) 33 ½ 34 ½ (850 876 mm) 6 ¼ (160 mm) Power cord Inlet valve hose IMPORTANT: ONLY E THE WATER SUPPLY HOSE PROVIDED WITH THIS MACHINE. ASKO provides a quality PEX water fill hose that utilizes a standard ¾ brass connection fitting for attachment on the water supply / faucet side and a threaded fitting for the washer side connection. Every ASKO washer is delivered ready-fitted with a plug and is intended for connection to an ASKO dryer, which is equipped with a matching receptacle. If the washer is used separately or with another dryer, it must be on a separate 220 V, 20 Amp single-phase circuit. Second-floor (above grade) installations must meet all local building codes. When placing the washer next to a wall or cabinet, be sure to leave ¼ (6 mm) of space between the washer and the wall or cabinet. Specifications are subject to change without notice. See installation instructions for additional details. 33
T744 T744 Type: Family size dryer Line Series Classic, ADA Compliant Color: White PROGRAMS Auto heavy, Auto normal, Auto delicate and Auto iron dry OPTIONS Anti-Crease, Low temperature Capacity UltraCare family size capacity/3.9 cu.ft. TECHNOLOGY SensiDry-sensor, Butterfly drying system, Double lint filter and Cleanable fan. Easy access condensor chamber Construction Stainless Steel drum, Three ball bearing suspension, Heavy duty life-tested motor. SIMPLICITY/COMFORT Line Series Classic control with LED display, Program memory, Vents up to 60' & 3-way venting, Stacking kit included and Reversible door SAFETY Certified on UL 2158/CSA C22.2 112 Electric Dryer Fire Containment Standard ASKO Appliances, Inc. P.O. Box 940609 Plano, TX 75094-0609
Planning & Design: Family-Size Dryer Line Series 744 Vented Dryers Unit Dimensions Height: 33 3/8 34 ½ 851 876 mm Depth: T744 23 7 /8 * 606 mm DEPTH WITH DOOR OPEN T744 46 1 /8 1172 mm Technical Data Supply voltage Max Wattage Single-phase 208-240V, 60 Hz 3000 W NOTE: When on a separate outlet, use 220 V, 20 Amp single-phase circuit. When an ASKO wash er is connected, use 220 V, 30 Amp sin gle-phase circuit. WEIgHT: 86 lbs 39 kg * Includes control knob. ** Does not include accessory door panel. 23 ½ (FI Model) 47 7 /8 (1216 mm) 46 1 /8 (1172 mm) 23 7 /8 (606 mm) (FI Model) 23 1 /8 (587 mm) 5 (127 mm) 4 1 /8 (105 mm) 33 3 /8 34 (848 mm 864 mm) 28 ¼ (718 mm) Power Cord 15 3 /16 (386 mm) Exhaust 5 7 /8 (150 mm) 34 The door hinges on ASKO dryers are shipped left-hinged, but they are reversible. See the ASKO Dryer Use and Care Guide for more information. When placing the dryer next to a wall or cabinet, be sure to leave ¼ (6 mm) of space between the dryer and the wall or cabinet. See page 35-36 for stacked washer/dryer dimensions. See pages 38-40 for cutout dimensions for closet and under-cabinet installations. Note: Power cord not supplied with unit. Specifications are subject to change without notice. See installation instructions for additional details. Venting Requirements WARNING! To reduce the risk of fire, vented dryers must be exhausted OUTDOORS or the equivalent. Never cover the end of the dryer stub or vent hose with anything to catch lint, except for a UL-approved vent basket. The exhaust hose should be run with as few bends as possible to the point of discharge. Maximum duct length of 60 (1829 cm) is allowed. Make any bends as gentle as possible. A maximum of four 90 bends may be fitted in the hose, otherwise the performance of the dryer will be impeded. Subtract 4 (122 cm) of duct for each 90 elbow. If more than 20' (210 cm) of duct is needed, we recommend increasing the diameter of the duct to 6 or 8 (152 mm or 203 mm). If the exhaust hose is taken to a wall outlet, a ventilation grill should be fitted to prevent reverse flow of cold air. Fit the ventilation grill to the outside or inside of the wall. This appliance should not be exhausted into a chimney, a wall, a ceiling, or a concealed space of a building. Only a metal ventilation grill should be used. Installation Examples Subtract 4 feet (122 cm) for every 90 elbow.
Planning & Design: Family-Size Dryer Line Series T744C Condenser Dryers (Ventless) Unit Dimensions Height: 33 3 /8 34 848 864 mm Depth: 23 7 /8 606 mm Depth w/door open: 46 1 /8 1172 mm Weight: 104 lbs 47 kg * Includes control knob. Technical Data Supply voltage Max Wattage Single-phase 208-240 V, 60 Hz 2800 W NOTE: When on a separate outlet, use 220 V, 20 Amp single-phase circuit. When an ASKO wash er is connected, use 220 V, 30 Amp sin gle-phase circuit. 23 ½ 23 7 /8 (606 mm) (FI Model) 23 1 /8 (587 mm) 46 ¼ (1175 mm) 5 (127 mm) 1 ¾ (44 mm) hose Power cord 33 3 /8 34 (848 864 mm) The door hinges on ASKO dryers are shipped left-hinged, but they are reversible. See the ASKO Dryer Use and Care Guide for more information. When placing the dryer next to a wall or cabinet, be sure to leave ¼ (6 mm) of space between the dryer and the wall or cabinet. NOTE: Condenser dryers require adequate ventilation for proper operation. NOTE: A louvered door is recommended for closet installations. See page 35-36 for stacked washer/dryer dimensions. See pages 37-40 for cutout dimensions for closet and under-cabinet installations. Note: Power cord not supplied with unit. NOTE: The drain hose must not be more than 40 (1016 mm) above the floor or the bottom of the unit. 2 3 Condensation Requirements You must install the dryer so the condensed water will continuously flow into a drain or sink. To do this, follow the instructions below: 1. Disconnect the short hose (1) from the blue connection. (It s okay to let the hose hang down.) 2. Connect the rubber hose supplied with the dryer to the blue nipple (2). 3. Run the hose to a drain or sink, as illustrated. 1 3 40" (1016 mm) maximum height Specifications are subject to change without notice. See installation instructions for additional details. 35
Planning & Design: Family-Size Stacked Laundry Pairs Line Series Classic W6324/T744(Ventless), W6324/T744C Condenser Dryer With 6 HiddenHelper : 72 ¾ 74 ¾ (1848 mm 1898 mm) 66 ¾ 68 ¾ (1695 mm 1746 mm) Dimensions Height 67 69 1702 1753 mm Height w/6 HH: ** 73 75 1854 1905 mm Depth: 23 7 /8 * 632 mm Weight: 247 265 lbs 112 120 kg * Includes control knob. ** Height with 6 (152 mm) HiddenHelper installed. The following 6 (152 mm) height HiddenHelpers models are available HI115, HDB115, HB115. 23 ½ 38 ½ 40 ½ ** (978 mm 1028 mm) 46 ¼ (1175 mm) 23 7 /8 (606 mm) 4 1 /8 (105 mm) 36 (914 mm) ** No venting required for condenser dryer (T753C). When HiddenHelper is specified, see pages 42-43. The following 6 (152 mm) height HiddenHelpers models are available HI115, HDB115, HB115. Any ASKO family-size dryer can be mounted on top of any matching ASKO washer. Stacking kits are provided with the ASKO family-size dryer. Refer to the ASKO family-size dryer Use and Care Guide for stacking instructions. Every ASKO family-size washer is delivered ready-fitted with a plug and is intended for connection to an ASKO family-size dryer which is equipped with a matching receptacle. When an ASKO family-size washer is connected to the ASKO family-size dryer, use 220 V, 30 Amp sin gle-phase circuit. When the ASKO family-size dryer is on a separate outlet, use 220 V, 20 Amp single-phase circuit. If the washer is used separately or with another dryer, it must be on a separate 220 V, 20 Amp single-phase circuit. When placing a stacked set next to a wall or cabinet, be sure to leave ¼ (6 mm) of space between the washer and the wall or cabinet. NOTE: Condenser dryers require adequate ventilation for proper operation. A louvered door is recommended for closet installations. ASKO condenser dryers must be installed to continuously drain through a hose attached to the rear of the machine. To ensure proper drainage, the drain must not be higher than 40 (1016 mm) above the bottom of the dryer. See page 33 for venting requirements. See page 34 for condensation drain requirements. See page 38 for stacked cabinet or closet installation dimensions. WARNING! Never stack a washer on top of a dryer! WARNING! To reduce the risk of fire, vented dryers must be exhausted OUTDOORS or the equivalent. Never cover the end of the dryer stub or vent hose with anything to catch lint, Specifications are subject to change without notice. See installation instructions for additional details. 37
Planning & Design: Family-Size Laundry Stacked cabinet or closet installations ASKO s front controls make it possible to install the washers and dryers under a cabinet or in a closet. Make sure there is a ¼ (6 mm) minimum clearance between units and cabinet or wall. To ensure proper ventilation, we recommend louvered doors, particularly for condenser dryers. Every ASKO family-size washer is delivered ready-fitted with a plug and is intended for connection to an ASKO family-size dryer which is equipped with a matching receptacle. When an ASKO family-size washer is connected to the ASKO family-size dryer, use 220 V, 30 Amp sin gle-phase circuit. When the ASKO family-size dryer is on a separate outlet, use 220 V, 20 Amp single-phase circuit. If the ASKO family-size washer is used separately or with another dryer, it must be on a separate 220 V, 20 Amp single-phase circuit. Cutout Dimensions Height: 67 ½ 69 ½ 1715 1765 mm Height w/hh: * 72 ¾ 74 ¾ 1845 1870 mm Width: 24 610 mm Depth: 25 635 mm * Height with 6 (152 mm) HiddenHelper installed Vented Dryer Opening T794FI, T784 and T754 family-size dryers can be vented from the rear, left or right side. The cabinet cutout illustrated below gives the dimensions for a rear exhaust. See page 33 for venting requirements. 4 1 /8 (105 mm) See note 220V 30 Amp Single Phase Outlet 25 (635 mm) Height with 6 (152 mm) HiddenHelper : 45 ¼ 46 ¼ (1149 mm 1174 mm) 39 ¼ 40 ¼ (997 mm 1022mm) Cold Water 15 ¾ min (400 mm) 24 ½ minimum (622 mm) 72 ¾ 74 ¾ (1848 mm 1898 mm) with 6 HiddenHelper 67 ½ 69 ½ (1715 mm 1765 mm) Height does not include the height of any vent duct materials. NOTE: To avoid crimping the electrical and water con nec tions, do not install the hookups between the area of 26 (660 mm) to 35 (889 mm) from the floor (as indicated by shaded area in illustrations above). For stacked installations, we recommend a 6' (1829 mm) cord. Never cover the end of the dryer stub or vent hose with anything to catch lint, except for a UL-approved vent bucket. Condenser Dryer Opening ASKO condenser dryers must be installed to continuously drain through a hose attached to the rear of the machine. To ensure proper drainage, the drain must not be higher than 40 (1016 mm) above the bottom of the dryer. See page 34 for condensation drain requirements. See note 220V 30 Amp Single Phase Outlet 25 (635 mm) Cold Water 15 ¾ min (400 mm) 24 ½ minimum (622 mm) 72 ¾ 74 ¾ (1848 mm 1898 mm) with 6 (152 mm) HiddenHelper \ 67 ½ 69 ½ (1715mm 1765 mm) When HiddenHelper is specified, see pages 46-47. The following 6 (152 mm) height HiddenHelpers models are available - HI115, HDB115, HB115. WARNING! To reduce the risk of fire, vented dryers must be exhausted OUTDOORS or the equivalent. NOTE: A louvered door is recommended for closet installations using an ASKO condenser dryer. Specifications are subject to change without notice. See installation instructions for additional details. Height does not include the height of any vent duct materials. 39