Installation Plan Washing Machine PW 811 PW 814 PW 818 To prevent accidents and machine damage, read these instructions before installation or use. en-us M.-Nr. 10 668 670
Contents Installation and planning notes... 4 Installation requirements... 4 Storage/Transportation... 4 General operating conditions... 4 Installation... 5 Installation on concrete base... 5 Leveling the machine... 6 Securing the machine... 6 Installation of steam-heated washing machines... 7 Steam connection valve... 7 Condensate trap... 7 Heater bank information... 8 Fitting information for steam and condensate hoses... 8 Machine connections... 9 Electrical connection... 10 Water connection... 12 Cold water connection... 12 Hot water connection... 12 Drain valve... 12 Dispenser pump connections... 14 Optional accessories... 15 XKM RS232 communication module... 15 Base... 15 Weighing base... 15 Suds drain and vapor vent (BWS)... 15 Technical drawings - dimensions in inches... 16 PW 811... 16 Dimensions... 16 Dimensions with Miele base (UG/UO)/weighting base (WI)... 17 Installation... 18 PW 814... 19 Dimensions... 19 Dimensions with Miele base (UG/UO)/weighting base (WI)... 20 Installation... 21 PW 818... 22 Dimensions... 22 Dimensions with Miele base (UG/UO)/weighting base (WI)... 23 Installation... 24 Anchoring PW 811/814/818... 25 Attaching to the floor/concrete base... 25 Attaching to the floor/concrete base when installing in a run... 25 Attaching to the floor with Miele base... 26 Technical drawings - dimension in millimeters... 27 PW 811... 27 Dimensions... 27 Dimensions with Miele base (UG/UO)/weighting base (WI)... 28 Installation... 29 2
Contents PW 814... 30 Dimensions... 30 Dimensions with Miele base (UG/UO)/weighting base (WI)... 31 Installation... 32 PW 818... 33 Dimensions... 33 Dimensions with Miele base (UG/UO)/weighting base (WI)... 34 Installation... 35 Anchoring PW 811/814/818... 36 Attaching to the floor/concrete base... 36 Attaching to the floor/concrete base when installing in a run... 36 Attaching to the floor with Miele base... 37 Technical data... 38 Water connection... 38 Models with detergent dispenser drawer (WEK)... 38 Drain valve... 38 Optional steam valves for steam-heated models... 38 Electric steam valve (ELD 01)... 38 Pneumatic steam valve (PND)... 38 Connection for equipotential bonding... 38 Anchoring... 39 Attaching to the floor... 39 Attaching to the floor with Miele base... 39 Attaching to a concrete base (provided on-site)... 39 PW 811... 40 Electrical version and electrical data... 40 Installation dimensions... 40 Transport data, weight and floor load... 41 Emissions data... 41 PW 814... 42 Electrical version and electrical data... 42 Installation dimensions... 43 Transport data, weight and floor load... 43 Emissions data... 43 PW 818... 44 Electrical version and electrical data... 44 Installation dimensions... 45 Transport data, weight and floor load... 45 Emissions data... 45 3
Installation and planning notes Installation requirements The washing machine must be installed by Miele Service or by properly trained staff of an authorized dealer. This washing machine must be installed in accordance with all relevant regulations and standards. Local energy supplier regulations must also be observed. This washing machine must only be operated in a room that has sufficient ventilation and which is frost-free. The washing machine should not be installed or operated in any area where there is a risk of explosion. Storage/Transportation The following conditions must be observed for transport and storage of the machine: Ambient temperature: 32-105 F (0-40 C) Humidity: non-condensing General operating conditions This washing machine is intended only for use in an industrial environment and must only be operated indoors. Ambient temperature of location: 32-105 F (0-40 C) Relative humidity: non-condensing Maximum height above sea level of location site: 6500 ft (2000 m) Depending on the nature of the installation site, sound emissions and vibration may occur. Tip: Have the installation site inspected and seek the advice of a professional in instances where increased noise may cause a nuisance. 4 PW 811 / PW 814 / PW 818
Installation Installation and planning notes This washing machine must be transported to its installation site using a suitable pallet jack. Remove the transport packaging. The washing machine must be set up on a level and firm surface with the minimum stated load bearing capacity (see "Technical data"). The floor load created by the washing machine is concentrated and transferred to the installation footprint via the machine feet. Tip: A concrete floor is the most suitable installation surface for this machine, being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface. The washing machine requires a gap of at least 2" (50 mm) on each side to allow for movement during operation. To ensure suitable access for further maintenance and service work, please ensure a minimum distance of 16" (400 mm) is maintained between the back of the machine and the wall. Installation on concrete base The washing machine can be installed on a concrete base if desired. The concrete materials and the durability of the concrete base must be assessed in accordance with the floor load bearing capacity given in "Technical data". To guarantee the stability of the washing machine, make sure that the concrete base is sufficiently stable on the floor and that it is capable of withstanding any burden or force from the washing machine. The washing machine must be secured to the concrete base using the fixtures and fastenings supplied. The washing machine must be secured to the base immediately after installation! There is a risk of the washing machine falling off a raised base during a spin cycle if it is not secured. PW 811 / PW 814 / PW 818 5
Installation and planning notes Leveling the machine Align the washing machine vertically and horizontally using the adjustable feet and a spirit level. The washing machine must stand perfectly level on all four feet to ensure safe and proper operation. Otherwise water and energy consumption will be increased and the machine could move. After aligning the machine tighten the lock nuts by turning them in a counterclockwise direction with a wrench. This will prevent the feet from moving. Securing the machine The feet of the washing machine must be secured to the concrete base using the fixtures and fastenings supplied. Fittings supplied are for installation on a concrete floor. For other types of flooring please purchase suitable fitting materials separately. 6 PW 811 / PW 814 / PW 818
Installation and planning notes Installation of steam-heated washing machines The steam connection must only be carried out by a registered installer. During connection please observe the installation instructions, the data plate on the washing machine, the wiring diagram, the installation diagram and the documentation supplied. Steam-heated washing machines must in all cases be secured to the floor! Steam connection valve Condensate trap Before connecting a steam-heated machine, ensure that the steam inlet valve, the dirt filter and the steam shut-off valve have been correctly installed on site. Steam valves are available from Miele service. With steam-heated washing machines a condensate trap is required for the condensate drain. The condensate trap ensures that condensate is completely drained away from the washing machine heater bank. The condensate trap must be installed in such a way that condensate cannot get back into the heater bank when the machine is not in operation. Tip: Use a bell condensate trap for the condensate drain. a Steam valve b Condensate trap PW 811 / PW 814 / PW 818 7
Installation and planning notes Heater bank information Fitting information for steam and condensate hoses To avoid damage to the heater bank the following must be observed during commissioning: In order to avoid unnecessary heat variations, ensure that heating is even. Do not allow sudden bursts of steam. To prevent corrosion, preparation of the water supply is absolutely essential. In particular, when the machine is not in operation, it must be ensured that no air or CO 2 can enter the steam system. Protect the heater bank from aggressive gases. The entire heating system must guarantee that no operating pressure or temperature can arise that is higher than the details given on the data plate. All appropriate regulations, standards and legislation from responsible authorities and accident prevention associations for heating and ventilation systems (in particular for the operation of the heat exchanger) must be observed. Make sure that steam and condensate hoses are not twisted or compressed. Do not use the hoses to compensate for connection tube misalignments! 8 PW 811 / PW 814 / PW 818
Machine connections Installation and planning notes 1 2 3 4 5 6 7 8 9 10 a Detergent dispenser (WEK) b Communication module slot The XKM RS232 communication module is available as an optional accessory. c Electrical connection d 2 x hard water connection (Optional) e Cold water connection f Hot water connection Water temperature to maximum 158 F (70 C) g Cold water connection h Cold water connection for liquid dispensing (Optional) i Connections for external dispenser pumps For up to 12 dispenser pumps. j Vapor extraction/free outlet Type AB k Drain pipe Connection for plastic pipe NPS 2 ¾" (HT DN 70). l Connection option for direct/indirect steam (Depending on model) 11 12 PW 811 / PW 814 / PW 818 9
Installation and planning notes Electrical connection The electrical connection must only be carried out by a qualified electrician who must ensure that all electrical work is carried out in accordance with applicable electrical regulations and standards. The washing machine must be connected to an electrical supply that complies with local and national regulations. Please also observe your insurance and energy supplier's regulations as well as any health and safety at work regulations. The required voltage, power consumption and specifications for external fusing are quoted on the data plate on the washing machine. Ensure that the supply voltage complies with the voltage quoted on the data plate before connecting the washing machine to the power supply. Connection to a supply voltage other than the one quoted on the data plate can lead to functional faults and damage the washing machine. If more than one voltage is quoted on the data plate, the washing machine can be converted for connection to the voltages stated. Conversion to a different voltage must only be carried out by a Miele Service engineer or by an authorized Service Dealer. The wiring instructions given on the wiring diagram must be followed. The washing machine can either be hard-wired or connected via a plug and socket that complies with national codes and regulations. For a hard-wired connection an all-pole isolation device must be installed on site. For hard-wired machines connection should be made via a suitable switch with all-pole isolation which, when in the off position, ensures a 1/8" (3 mm) gap between all open contacts. These include circuit breakers, fuses and relays. If the power supply cannot be permanently disconnected, the isolator switch (including plug and socket) must be safeguarded against being switched on either unintentionally or without authorization. Tip: We recommend connection to the power supply via a suitable plug and socket which must be easily accessible for servicing and maintenance work after the machine has been installed. 10 PW 811 / PW 814 / PW 818
Installation and planning notes If it is necessary to install a residual current device (RCD) in accordance with local regulations, a residual current device type B (sensitive to universal current) must be used. An existing type A residual current device, (RCD) must be exchanged for a type B RCD. If necessary, equipotential bonding with good galvanic contact must be guaranteed in compliance with all applicable local and national installation specifications. Equipotential bonding must have an earth current rating > 10 ma. Accessories for equipotential bonding are not supplied and need to be ordered separately. PW 811 / PW 814 / PW 818 11
Installation and planning notes Water connection The washing machine complies with current local and national safety regulations protecting the drinking water supply and can therefore be connected to the drinking water supply without a nonreturn valve. The machine is designed to operate with a supply pressure of between 14.5 psi (1 bar) and must not exceed 145 psi (10 bar). If it is highter than 145 psi (10 bar) a pressure reducing valve must be used. The machine must be connected to the water supply using the inlet hoses provided. The connection points are subject to water supply pressure. Turn on the faucet slowly and check for leaks. Correct the position of the seal and union if necessary. Cold water connection A supply faucet with ¾" threaded union is required for each connection to the water supply (single or double). If this is not present, the washing machine should be connected to the water supply by a qualified plumber. The inlet hose for cold water (blue stripes) is not intended to be used with a hot water supply line. Hot water connection To minimize energy consumption during operation with hot water, the washing machine should be connected to a hot water ring circuit. So-called "transmission lines" (single lines to hot water generators) can result in cooling down of the water remaining in the pipes if not in constant use. More energy would then be consumed to heat the water up again. Use the inlet hose supplied (red stripes) for the hot water connection. The temperature of the water intake must not exceed 158 F (70 C). If there is no hot water supply at the installation location for the washing machine, the connection hose must nevertheless be connected to the cold water supply. A Y-piece is required in this case. The cold water consumption increases accordingly to account for the missing hot water intake. For functional and technical reasons it is not possible to operate the machine exclusively with a hot water connection (without a separate cold water intake). Even if a hot water connection is present, the washing machine must be connected to a cold water intake. 12 PW 811 / PW 814 / PW 818
Installation and planning notes Drain valve A motorized dump valve is used to drain the machine. A 2 ¾" angle connector can be used for draining the machine directly into the waste water system (without a siphon) or into an on-site gully (with odor trap). The dump valve can also be operated manually to allow the suds container to be emptied in the event of a power outage. A vented drainage system is vital for unimpeded drainage. If several machines are connected to a single drain pipe, it should be large enough to allow all machines to drain simultaneously. The appropriate Miele installation set M.-No.: 05 238 090 is available from Miele for venting a 2 ¾" (DN 70) pipe. If the slope for drainage is extremely steep, the piping must be vented so prevent formation of a vacuum in the machine's drain system. Slow or obstructed drainage or a backup of water in the drum as a result of undersized pipework can result in faults occurring during programs, which will result in error messages appearing in the display. Outflowing suds can be as hot as 203 F (95 C). Danger of injury by burning! Avoid direct contact. PW 811 / PW 814 / PW 818 13
Installation and planning notes Dispenser pump connections Up to 12 dispenser pumps can be connected to the washing machine. Dispenser pump connections on the back of the machine Connections 1 and 2 are for viscous agents. These connectors are sealed and need to be drilled out before connection with a 5/16" (8 mm) drill bit. Make sure that you only drill through the first panel (I) as there is a deflecting panel (II) 3/8" (10 mm) behind it. Connections 3 to 12 are for liquid dispensing. These connections are sealed and must be cut to the diameter of the hose with a small saw. If opened connections are no longer required, they must be resealed using a suitable sealant (e.g. silicone). Connection terminals for five time-controlled dispenser pumps, which can be operated without a multifunction module, are located behind the cover adjacent to the electrical connection. Calibration of the dispenser pumps and regulation of dispensing quantities is carried out automatically for washing machines fitted with a multifunction module. A flowmeter or throughput sensors can be connected for precise monitoring of the dispensing quantity. Connections for level monitoring are available for every agent dispensed. 14 PW 811 / PW 814 / PW 818
Optional accessories Installation and planning notes Only use genuine Miele spare parts and accessories with this machine. Using spare parts or accessories from other manufacturers will void the warranty, and Miele cannot accept liability. XKM RS232 communication module The serial interface RS-232 can be retrofitted to the washing machine via an XKM RS 232 (optional accessory available from Miele). This communication module must only be used with Miele Professional machines that are fitted with an appropriate slot for the module. The data interface provided via communication module XKM RS232 complies with SELV (Safety Extra Low Voltage) in accordance with EN 60950. Machines connected to this interface must also be SELV compliant. Communication module XKM RS 232 is supplied with a connection cable and a D-sub-connector. Base The machine can be installed on a machine base (open or box base, available as an optional Miele accessory). Elevating the washing machine gives a better ergonomic working position when loading or unloading. It also simplifies the installation of a waste water connection. When installed on a raised base, the machine must be secured to the base and the base must be secured to the floor. There is a risk of the washing machine falling off a raised base during a spin cycle if it is not secured. Weighing base The washing machine is optionally available with a weighing base. In this version, the actual weight of the laundry load is displayed during loading along with the maximum laundry load weight for the unit. Make sure that the washing machine is not in contact with objects or people located nearby or leaning against it. They could be weighed as well and falsify the load weight shown on the display. Suds drain and vapor vent (BWS) If excessive suds form, suds may escape from the vapor vent. To drain the suds, an optional vapor vent kit (BWS) can be installed. PW 811 / PW 814 / PW 818 15
Technical drawings - dimensions in inches PW 811 Dimensions 31.5" 32.6" 19.4" 16.3" 53.2" 20.9" 29.1" 53.2" 31.4" 37" 1" 6.5" 31.5" 31.4" 21" 53.2" 3.5" 32.6" 18.6" 0.9" 3.4" 31.4" Dimensions in inches 16 PW 811 / PW 814 / PW 818
Technical drawings - dimensions in inches Dimensions with Miele base (UG/UO)/weighting base (WI) 31.5" 32.6" 19.4" 32.3" 16.3" 40.5" 64.6" 64.7" 3.5" 32.6" 31.4" 37" 1" 31.5" 31.4" 30" 21" 64.6" Dimensions in inches PW 811 / PW 814 / PW 818 17
Technical drawings - dimensions in inches Installation 23" 27.4" 50.4" 50.4" 15.8" 15.8" 33.3" 5.9" 13.7" 27.4" 3.6" Dimensions in inches 18 PW 811 / PW 814 / PW 818
Technical drawings - dimensions in inches PW 814 Dimensions 36.4" 29.8" 19.4" 22.3" 16.3" 57.1" 57.2" 21" 30.4" 57.1" 2.7" 29.8" 20" 36.3" 33.5" 0.9" 1" 7.1" 36.4" 36.3" 4.4" Dimensions in inches PW 811 / PW 814 / PW 818 19
Technical drawings - dimensions in inches Dimensions with Miele base (UG/UO)/weighting base (WI) 36.4" 29.8" 19.4" 32.3" 16.3" 40.5" 67.2" 67.3" 2.7" 29.8" 30 21" 67.2" 36.3" 33.5" 1" 36.4" 36.3" Dimensions in inches 20 PW 811 / PW 814 / PW 818
Technical drawings - dimensions in inches Installation 20.2" 24.7" 45.7" 5.8" 45.7" 15.8" 15.8" 38.2" 16.2" 32.4" 3.3" Dimensions in inches PW 811 / PW 814 / PW 818 21
Technical drawings - dimensions in inches PW 818 Dimensions 36.4" 33.8" 19.4" 22.3" 2.6" 33.8" 36.3" 37.4" 1" 36.4" 36.3" 16.3" 57.1" 57.2" 30.4" 20" 21" 57.1" 0.9" Dimensions in inches 22 PW 811 / PW 814 / PW 818
Technical drawings - dimensions in inches Dimensions with Miele base (UG/UO)/weighting base (WI) 36.4" 33.8" 19.4" 32.3" 16.3" 40.5" 67.2" 67.3" 2.6" 33.8" 30" 21" 67.2" 36.3" 37.4" 1" 36.4" 36.3" Dimensions in inches PW 811 / PW 814 / PW 818 23
Technical drawings - dimensions in inches Installation 24.1" 28.6" 49.6" 5.8" 49.6" 15.7" 15.7" 38.2" 16.2" 32.3" 3.2" Dimensions in inches 24 PW 811 / PW 814 / PW 818
Anchoring PW 811/814/818 Attaching to the floor/concrete base Technical drawings - dimensions in inches ~ 3 1/2" Ø 1/2" Dimensions in inches Attaching to the floor/concrete base when installing in a run ~ 3 1/2" Ø 1/2" Dimensions in inches PW 811 / PW 814 / PW 818 25
Technical drawings - dimensions in inches Attaching to the floor with Miele base ~ 3 1/2" Ø 1/2" Dimensions in inches 26 PW 811 / PW 814 / PW 818
Technical drawings - dimension in millimeters PW 811 Dimensions 799 827 492 415 1350 529 737 1352 795 940 25 164 799 795 531 1350 87 828 472 22 86 795 Dimensions in millimeters PW 811 / PW 814 / PW 818 27
Technical drawings - dimension in millimeters Dimensions with Miele base (UG/UO)/weighting base (WI) 799 827 492 820 415 1027 1640 1642 87 828 795 940 25 799 795 762 531 1640 Dimensions in millimeters 28 PW 811 / PW 814 / PW 818
Technical drawings - dimension in millimeters Installation 583 697 1280 1280 400 400 845 148 696 348 91 Dimensions in millimeters PW 811 / PW 814 / PW 818 29
Technical drawings - dimension in millimeters PW 814 Dimensions 924 757 492 564 415 1450 1452 531 772 1450 67 757 507 921 850 22 25 179 924 920 112 Dimensions in millimeters 30 PW 811 / PW 814 / PW 818
Technical drawings - dimension in millimeters Dimensions with Miele base (UG/UO)/weighting base (WI) 924 757 492 819 415 1027 1705 1707 67 758 762 531 1705 920 850 25 924 920 Dimensions in millimeters PW 811 / PW 814 / PW 818 31
Technical drawings - dimension in millimeters Installation 513 627 1160 148 1160 400 400 970 411 821 82 32 PW 811 / PW 814 / PW 818
Technical drawings - dimension in millimeters PW 818 Dimensions 924 857 492 564 66 858 920 950 25 924 920 415 1450 1452 772 507 531 1450 22 Dimensions quoted in millimeters PW 811 / PW 814 / PW 818 33
Technical drawings - dimension in millimeters Dimensions with Miele base (UG/UO)/weighting base (WI) 924 857 492 819 415 1027 1705 1707 66 858 762 531 1705 920 950 25 924 920 Dimensions quoted in millimeters 34 PW 811 / PW 814 / PW 818
Technical drawings - dimension in millimeters Installation 613 727 1260 148 1260 400 400 970 411 821 82 PW 811 / PW 814 / PW 818 35
Technical drawings - dimension in millimeters Anchoring PW 811/814/818 Attaching to the floor/concrete base ~ 90 Ø 12 Dimensions in millimeters Attaching to the floor/concrete base when installing in a run ~ 90 Ø 12 Dimensions in millimeters 36 PW 811 / PW 814 / PW 818
Attaching to the floor with Miele base Technical drawings - dimension in millimeters ~ 90 Ø 12 Dimensions in millimeters PW 811 / PW 814 / PW 818 37
Technical data Water connection Models with detergent dispenser drawer (WEK) Permitted supply pressure Maximum intake rate Cold water connection (to be provided on site, external thread according to DIN 44991, flat seal) Optional cold-hard water connection (to be provided on site, external thread according to DIN 44991, flat seal) Hot water connection 158 F (70 C) (to be provided on site, external thread according to DIN 44991, flat seal) Intake hose length 14.5-145 psi (1-10 bar) 21 gal/min (79.5 l/min) 2 x ¾" 2 x ¾" 1 x ¾" (25 x 19 mm) 59" (1500 mm) Drain valve Maximum drain water temperature Waste water connection (on machine) Drain (on-site) Maximum drainage rate 203 F (95 C) NPS 2 ¾" (DN 70) plastic pipe 2 ¾" connection 53 gal/min (200 l/min) Optional steam valves for steam-heated models Electric steam valve (ELD 01) Regulatable steam pressure Connection size Connection voltage Frequency 29-145 psi (200-1000 kpa) 1/2" (12 mm) 1N AC 230 V 50-60 Hz Pneumatic steam valve (PND) Regulatable steam pressure Connection size 0-145 psi (0-1000 kpa) 1/2" (12 mm) Connection for equipotential bonding Connection with male thread (machine) 3/8" x 1 3/8" (10 x 35 mm) Washers and nuts M 10 38 PW 811 / PW 814 / PW 818
Technical data Anchoring Attaching to the floor Required anchor points 2 Wood screw (diameter x length) Wall anchors (diameter x length) 1/2" x 3 1/2" (12 mm x 90 mm) 5/8" x 3 1/8" (16 mm x 80 mm) Attaching to the floor with Miele base Required anchor points 4 Wood screw (diameter x length) Wall anchors (diameter x length) 1/2" x 3 1/2" (12 mm x 90 mm) 5/8" x 3 1/8" (16 mm x 80 mm) Attaching to a concrete base (provided on-site) Required anchor points 2 Wood screw (diameter x length) Wall anchors (diameter x length) 1/2" x 3 1/2" (12 mm x 90 mm) 5/8" x 3 1/8" (16 mm x 80 mm) PW 811 / PW 814 / PW 818 39
Technical data PW 811 Electrical version and electrical data Electrically heated Standard Connection voltage 3 AC 220-240 V Frequency 60 Hz Fuse rating (on site) 3 x 25 A Power rating 10.2-11.8 kw Rated current 3 x 23.2 A Power cord, min. cross-section 4 x AWG 12 Cord connector M 32 Convertible to: Connection voltage 3 AC 200-208 V Frequency 60 Hz Fuse rating (on site) 3 x 25 A Power rating 8.8-9.4 kw Rated current 3 x 21.2 A Power cord, min. cross-section 4 x AWG 12 Cord connector M 32 Installation dimensions Standard Casing width (without add-on components) Casing height (without add-on components) Casing depth (without add-on components) Overall machine width Overall machine height Overall machine depth Minimum width of transport opening Minimum distance between wall and front of appliance Minimum distance between wall and rear of appliance 31.4" (795 mm) 53.2" (1350 mm) 32.6" (827 mm) 31.5" (799 mm) 53.3" (1352 mm) 37" (940 mm) 31.7" (805 mm) 50.4" (1280 mm) 15.8" (400 mm) With Miele base (UG/UO) Casing width (without add-on components) Casing height (without add-on components) Casing depth (without add-on components) Overall machine width Overall machine height Overall machine depth Minimum width of transport opening Minimum distance between wall and front of appliance Minimum distance between wall and rear of appliance 31.4" (795 mm) 64.6" (1640 mm) 32.6" (827 mm) 31.5" (799 mm) 64.7" (1642 mm) 37" (940 mm) 31.7" (805 mm) 50.4" (1280 mm) 15.8" (400 mm) 40 PW 811 / PW 814 / PW 818
Technical data Transport data, weight and floor load Packaging width 44.5" (1130 mm) Packaging height 57.8" (1468 mm) Packaging depth 43" (1090 mm) Gross volume 63.9 cu. ft. (1808 l) Gross weight 701 lb (318 kg) Net weight 642 lb (291 kg) Maximum floor load during operation 4479 N Emissions data Workplace related sound pressure level, washing Sound power level, washing Workplace related sound pressure level, spinning Sound power level, spinning Average heat dissipation rate to installation site 51 db (A) 59.7 db (A) 65 db (A) 76.8 db (A) 3754 BTU (3.96 MJ/h) PW 811 / PW 814 / PW 818 41
Technical data PW 814 Electrical version and electrical data Electrically heated Standard: Connection voltage 3 AC 220-240 V Frequency 60 Hz Fuse rating (on site) 3 x 40 A Power rating 14.8-17.1 kw Rated current 3 x 37.2 A Power cord, min. cross-section 4 x AWG 8 Cord connector M 40 Convertible to: Connection voltage 3 AC 200-208 V Frequency 60 Hz Fuse rating (on site) 3 x 40 A Power rating 12.5-13.4 kw Rated current 3 x 32.4 A Power cord, min. cross-section 4 x AWG 8 Cord connector M 40 Steam-heated Standard: Connection voltage 3AC 220-240 V Frequency 60 Hz Fuse rating (on site) 3 x 16 A Power rating 2.3 kw Rated current 3 x 4.0 A Power cord, min. cross-section 4 x AWG 14 Cord connector M 25 Convertible to: Connection voltage 3AC 200-208 V Frequency 60 Hz Fuse rating (on site) 3 x 16 A Power rating 2.3 kw Rated current 3 x 4.0 A Power cord, min. cross-section 4 x AWG 14 Cord connector M 25 42 PW 811 / PW 814 / PW 818
Technical data Installation dimensions Standard Casing width (without add-on components) Casing height (without add-on components) Casing depth (without add-on components) Overall machine width Overall machine height Overall machine depth Minimum width of transport opening Minimum distance between wall and front of appliance Minimum distance between wall and rear of appliance 36.3" (920 mm) 57.1" (1450 mm) 29.8" (757 mm) 36.4" (924 mm) 57.2" (1452 mm) 33.5" (849,5 mm) 36.7" (930 mm) 45.7" (1160 mm) 15.8" (400 mm) With Miele base (UG/UO) Casing width (without add-on components) Casing height (without add-on components) Casing depth (without add-on components) Overall machine width Overall machine height Overall machine depth Minimum width of transport opening Minimum distance between wall and front of appliance Minimum distance between wall and rear of appliance 36.3" (920 mm) 67.2" (1705 mm) 29.8" (757 mm) 36.4" (924 mm) 67.3" (1707 mm) 33.5" (849.5 mm) 36.7" (930 mm) 45.7" (1160 mm) 15.8" (400 mm) Transport data, weight and floor load Packaging width 44.5" (1130 mm) Packaging height 61.8" (1568 mm) Packaging depth 43" (1090 mm) Gross volume 68.2 cu. ft. (1931 l) Gross weight 884 lb (401 kg) Net weight 825 lb (374 kg) Maximum floor load during operation 5400 N Emissions data Workplace related sound pressure level, washing Sound power level, washing Workplace related sound pressure level, spinning Sound power level, spinning Average heat dissipation rate to installation site 51 db (A) 59.6 db (A) 65 db (A) 76.2 db (A) Electrically heated versions: 5460 BTU (5.76 MJ/h) Steam-heated versions: 787 BTU (0.83 MJ/h) PW 811 / PW 814 / PW 818 43
Technical data PW 818 Electrical version and electrical data Electrically heated Standard: Connection voltage 3 AC 220-240 V Frequency 60 Hz Fuse rating (on site) 3 x 50 A Power rating 19.4-22.6 kw Rated current 3 x 48 A Power cord, min. cross-section 4 x AWG 8 Cord connector M 40 Convertible to: Connection voltage 3 AC 200-208 V Frequency 60 Hz Fuse rating (on site) 3 x 50 A Power rating 16.6-17.7 kw Rated current 3 x 41.8 A Power cord, min. cross-section 4 x AWG 8 Cord connector M 40 Steam-heated Standard: Connection voltage 3 AC 220-240 V Frequency 60 Hz Fuse rating (on site) 3 x 16 A Power rating 3 kw Rated current 3 x 4 A Power cord, min. cross-section 4 x AWG 14 Cord connector M 25 Convertible to: Connection voltage 3 AC 200-208 V Frequency 60 Hz Fuse rating (on site) 3 x 16 A Power rating 3 kw Rated current 3 x 4 A Power cord, min. cross-section 4 x AWG 14 Cord connector M 25 44 PW 811 / PW 814 / PW 818
Technical data Installation dimensions Standard Casing width (without add-on components) Casing height (without add-on components) Casing depth (without add-on components) Overall machine width Overall machine height Overall machine depth Minimum width of transport opening Minimum distance between wall and front of appliance Minimum distance between wall and rear of appliance 36.3" (920 mm) 57.1" (1450 mm) 33.8" (857 mm) 36.4" (924 mm) 57.2" (1452 mm) 37.4" (950 mm) 36.7" (930 mm) 49.7" (1260 mm) 15.8" (400 mm) With Miele base (UG/UO) Casing width (without add-on components) Casing height (without add-on components) Casing depth (without add-on components) Overall machine width Overall machine height Overall machine depth Minimum width of transport opening Minimum distance between wall and front of appliance Minimum distance between wall and rear of appliance 36.3" (920 mm) 67.2" (1705 mm) 33.8" (857 mm) 36.4" (924 mm) 67.2" (1707 mm) 37.4" (950 mm) 36.7" (930 mm) 49.7" (1260 mm) 15.8" (400 mm) Transport data, weight and floor load Packaging width 44.5" (1130 mm) Packaging height 61.8" (1568 mm) Packaging depth 46.9" (1190 mm) Gross volume 74.5 cu. ft. (1931 l) Gross weight 997 (452 kg) Net weight 937 lb (425 kg) Maximum floor load during operation 6037 N Emissions data Workplace related sound pressure level, washing Sound power level, washing Workplace related sound pressure level, spinning Sound power level, spinning Average heat dissipation rate to installation site 54 db (A) 62.0 db (A) 67 db (A) 79.0 db (A) Electrically heated versions: 7110 BTU (7.56 MJ/h) Steam-heated versions: 1024 BTU (1.08 MJ/h) PW 811 / PW 814 / PW 818 45
Please have the model and serial number of your machine available when contacting Technical Service. U.S.A. Miele, Inc. National Headquarters 9 Independence Way Princeton, NJ 08540 Phone: Fax: 800-991-9380 609-419-4241 www.miele-pro.com proinfo@mieleusa.com Technical Service & Support Phone: 800-991-9380 Fax: 800-220-1348 proservice@mieleusa.com Alteration rights reserved / Publication date: 0917 M.-Nr. 10 668 670 / 00 PW 811 PW 814 PW 818