SMX10-1, SMX20-1, SMX20-2, SMX30-1 MIXERS This manual contains important information regarding your Supera unit. Please read this manual thoroughly prior to equipment set-up, operation and maintenance. Failure to comply with regular maintenance guidelines outlined in this manual may void the warranty.
DESCRIPTION This is a type of changing speed gear mixer, with its planetary stirring design. It has a compact structure, is highly efficient and power saving, and is easy to operate. It will be provided to you as an ideal assistant for bread and cake making. TECHNICAL PARAMETERS MAIN EXTERNAL PARTS MIXER 1. Gear change hand lever 2. Stirring shaft 3. Mixer 4. Stainless barrel 5. Power switch 6. Bent lever 7. Safety guard (may choose the fitting) 8. Support
INSTALLATION Ensure the location of the Planetary Mixer is capable of supporting its weight. WARNING: The Planetary Mixer is very heavy, care must be taken when moving it. ASSEMBLY WARNING: The bowl must be attached and raised into position prior to starting the Planetary Mixer. We accept no responsibility for any injury caused by incorrect assembly of this appliance. Note: Ensure the feet are level to reduce vibration during operation. Remove the appliance from all packaging. Fitting/Removing the Bowl 1. Turn Off the appliance. 2. Open the safety guard by turning it to the left (SMX10-1, SMX20-1, & SMX20-2) or lifting it above the mixer (SMX30-1). 3. Lower the bowl with the bowl handle. 4. Release the locking catches either side of the bowl. 5. Lift the bowl. The bowl is held in place by two pins securing the handles to the cradle and a hole at the back of the appliance which houses the lug on the bowl lip. 6. Reverse the procedure to fit the bowl. Note: Ensure the handle is fully pushed back and the bowl is completely raised or the mixer will not work. Note: Regularly grease the bowl lift mechanism to ensure smooth operation. Changing the Mixer Attachment 1. Turn Off the appliance. 2. Open the safety guard by turning it to the left (SMX10-1, SMX20-1, & SMX20-2) or lifting it above the mixer (SMX30-1). 3. Lower the bowl with the bowl handle. 4. Push the mixer attachment up and to the left to release it. 5. Insert the desired attachment. Push up and to the right to lock it into place. 6. Raise the bowl.
OPERATION *CAUTION: The unit will not run if the safety guard is not closed completely! 1. Plug the unit into the proper outlet ensuring it has the correct voltage and amps. 2. Set your unit to desired speed. 3. Install desired attachment. (Beater, Dough Hook, or Wire Whip) 4. Install bowl and check to make sure it is secure and in the proper position. 5. Raise the hand lever so that it in the highest position. 6. Once the hand lever is raised, close the Safety Guard completely. If the Safety Guard is not closed the mixer will not function. 7. Make sure the safety guard lock is on before turning on the unit 8. To turn the unit on, press the GREEN power button. 9. To turn the unit off, press the RED power button. To change the desired speed, press the RED power button to turn the unit off. Move the hand lever into the lowest position. Select new desired speed. Raise hand lever back into highest position. Press GREEN power button to turn the unit back on. ACCESSORIES AND FUNCTIONS We recommend the following uses for each attachment: 1. Whisk: Light mixes, whipped cream, mayonnaise, egg whites, pancakes and souffles. Recommended Speed: 1, 2, 3, Fast 2. Beater: Firm mixes, light pastry, cake/biscuit mix, icings, fillings, and mashed vegetables. Recommended Speed: 1, 2, Medium 3. Spiral Dough Hook: Heavy mixes, dough, pie pastry, etc. Recommended Speed: 1, Slow NOTES 1. The power socket must be connected to a ground wire to guarantee optimal operation. There is a strong risk of malfunction or shock if the mixer is not grounded. The ground wire can never be connected to a gas pipe, water pipe, lightning rod, or telephone line. After installation, have an electrician check for electric leakage. If the power line is ever damaged, please consult a professional electrician. 2. Don t put your hand into the stirring barrel during operation. Power supply should be disconnected before the mixer is going to be installed. 3. Don t operate the mixer beyond the time limit. Doing so will reduce the life of the unit. 4. The mixer should be mounted on a stable and clean place. Keep it away from overheated or over-wet places and away from equipment which has strong electromagnetic pull or can produce a strong electromagnetic pull.
5. Keep the machine clean constantly. Disconnect power supply before maintenance. Clean it with a piece of soft and damp cloth. Don t clean it with liquid or spraying detergent. Overload Switch The Overload switch is situated at the Overload back of the machine beside the cable switch entry. If the appliance becomes too hot the Overload switch will stop the machine automatically. If this happens: 1. Turn Off the mixer. 2. Reduce the load in the mixing bowl. 3. Push the Overload switch back in to reset it. 4. Allow the appliance to cool for 20 minutes. Note: In the event of a power cut the Overload switch will cut in to prevent the appliance from restarting automatically when power is restored. Note: Always disconnect the Planetary Mixer from the mains powers supply when not in use. MAINTENANCE Always turn off the mixer and disconnect from the power supply before cleaning. Use warm soapy water to clean the bowl and mixing attachments. Do not use abrasive cleaning chemicals as these can leave behind harmful residues. Clean the exterior of the appliance with a damp cloth. Dry all parts thoroughly after cleaning. Do not use jet/pressure washers to clean the appliance. Clean the appliance regularly. The transmission gear box is greased in a factory, for best practice we recommend checking the grease every 6 months. To add or refill grease, open the top cover, then fill grease from aperture or replace the grease directly.
TROUBLESHOOTING Fault Probable Cause Action The appliance is not working The unit is not switched on Check the unit is plugged in correctly and switched on The Stop button not released (HLM30) Turn button clockwise to release Plug and lead are damaged Call agent or qualified Technician Fuse in the plug has blown Replace the fuse Power supply Check power supply The overload switch has activated See overload switch information in the Operation section of this manual Safety Guard not closed Close Safety Guard fully Appliance not in gear Put in gear Bowl not fully raised Ensure the Bowl lever is pushed back fully Bowl will not fit back in to place The appliance is overheating Bowl pins or surrounding area clogged with mix The mixing bowl is overloaded The appliance has been operating for too long Clean the appliance Turn off the appliance and empty some of the contents Turn off the appliance and allow to cool down for 30 minutes The appliance is noisy Bowl or mixing attachment not correctly fitted Remove and refit bowl/mixing attachment Worn bearings/damaged gears Call agent or qualified Technician The mixing attachment fails to rotate properly The belt has become loose Call agent or qualified Technician Cannot select gear Gearing cogs misaligned Turn Off appliance and manually turn the whisk attachment slightly. Select the gear again. WARNING! If the equipment is out of function, please have it serviced by a professional.
PARTS OF SMX10-1
PARTS OF SMX20-1
PARTS OF SMX20-2
PARTS OF SMX30-1 SER.NO. PART.NO. DESCRIPTION SER.NO. PART.NO. DESCRIPTION 1 30-1 Hook 49 30-49 Support 2 30-2 Beater 50 30-50 Clamp Plate 3 30-3 Wire Whip 51 30-51 Nut 4 30-4-Version 4 Safety Guard 52 30-52 Base 5 30-5 Bowl 53 30-53 Bearing 6 30-6 Top Cover 54 30-54 Transmission Shaft Support 7 30-7 Screw 55 30-55 Key 8 30-8 Spring 56 30-56 Circlips for Shaft 9 30-9 Pin Shaft 57 30-57 Gear 10 30-10 Shifting Yoke 58 30-58 Bushing 11 30-11 Cam-Gear Shifter 59 30-59 Front Housing 12 30-12 Plate-Shifter Index 60 30-60 Worm Wheel 13 30-13 Handle-Shifter 61 30-61 MARK 14 30-14 Handle Set 62 30-62 Case 15 30-15 Turnset 63 30-63 Back Cover 16 30-16 Speed Handle 64 30-64 Internal Gear 17 30-17-Version 4 Plug Attachment Hub 65 30-65-Version 4 Switch Axle 18 30-18-Version 4 Overload Switch 66 30-66 Seal Up Ring 19 30-19-Version 4 Power Cord 67 30-67 Gear Shaft 20 30-20-Version 4 Power Supply Waterproof Connectors 68 30-68 Gear 21 30-21-Version 4 Contact Switch 69 30-69 Bushing 22 30-22 Hood Ring 70 30-70 Gear 23 30-23 Circlips for Shaft 71 30-71 Gear 24 30-24 Planet Gear 72 30-72 Plate 25 30-25 Operating Shelf 73 30-73 Plug 1 26 30-26 Bearing 74 30-74 Nut 27 30-27 Oil Seal 75 30-75 Spring Plate 28 30-28 Pin 76 30-76 Bearing 29 30-29 Working Shaft 77 30-77 Shaft Worm Gear 30 30-30 Declutch Shift Shaft 78 30-78 Key 31 30-31 Plate 79 30-79 Circlips for Shaft 32 30-32 Main Shaft 80 30-80 Circlips for Shaft 33 30-33 Nut 81 30-81 Plug 2 34 30-34 Top Batter Valve Cap 82 30-82 Buffalo 230V/50HZ Motor (with tool) 35 30-35 Flat valve Cap 83 30-83-Version 4 Stop Block 36 30-36 Bearing 84 30-84 Green Button 37 30-37 Spacer-Lower 85 30-85 Red Button 38 30-38 Super Machine Parts 86 30-86 Crank Lever 38-1 30-38-1 Super Machine Parts 87 30-87 Handle-Shifter 38-2 30-38-2 Gear 88 30-88 Connecting Rod 38-3 30-38-3 Roller 89 30-89 Spring 38-4 30-38-4 Spring 90 30-90 Spring Plate 39 30-39 Gear 91 30-91 Clamp Plate 40 30-40 Bushing 92 30-92 Distance Switch 41 30-41 Sleeve 93 93-Version 4 Capacitor 42 30-42 Gear 94 94-Version 4 Capacitor 43 30-43 Clamp Plate 95 95-Version 4 Switch Mounting Collar 44 30-44 Bearing 96 96-Version 4 Switch Compression Spring 45 30-45 Bushing 97 97-Version 4 Split Washer 46 30-46 Oil Seal 98 98-Version 4 The Left Guard 47 30-47 Body Housing 99 99-Version 4 The Right Guard 48 30-48 Bowl Hold Kits
DECLARATION OF CONFORMITY Equiment Type: Supera Food Mixer Model: Number: Certificate:
www.superaco.com LIMITED WARRANTY SUPERA PLANETARY MIXER EQUIPMENT MODELS: Planetary Countertop Mixers: [SMX5-1, SMX7-1, SMX10-1, SMX20-1, SMX20-2] Planetary Floor Mixers: [SMX30-1] SUPERA, LLC warrants to the original purchaser of new equipment that said equipment, when installed in accordance with our instructions within North America and subjected to normal use, is free from defects in material or workmanship for one year. Warranty includes onsite service calls within 60 miles of an authorized service company. End user is responsible for all extra travel and mileage at prevailing rates and for original call to Supera expressing need for warranty service. Any service provided without authorization from Supera, LLC will not be covered by Supera, LLC. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED. SUPERA, LLC EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESSED OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. SUPERA, LLC HAS FINAL DESCRETION ON ALL WARRANTY REQUESTS. SUPERA, LLC S OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS EXPRESSLY LIMITED TO REPAIRING AND REPLACING EQUIPMENT WHICH PROVES TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITHIN THE APPLICABLE WARRANTY PERIOD. All repairs pursuant to this Warranty will be performed by an Authorized Designated SUPERA, LLC Service Location during normal working hours. This warranty does not cover services performed at overtime or premium labor rates. End user is responsible for the difference between normal service rates and premium service rates. This warranty does not cover any service technician errors. IN NO EVENT SHALL SUPERA, LLC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY, INCLUDING, WITHOUT LIMITATION, LOSS OF PROPERTY, PERSONAL INJURY, LOSS OF BUSINESS OR PROFITS OR OTHER ECONOMIC LOSSES, OR STATUTORY OR EXEMPLARY DAMAGES, WHETHER IN NEGLIGENCE, WARRANTY, STRICT LIABILITY, OR OTHERWISE. This warranty is given only to the first purchaser from a retail dealer. No warranty is given to subsequent transferees. Installation in a residential application will void all warranties. Warranty does not cover product failures caused by: failure to maintain, neglect, abuse, damage due to excess water, fire, normal wear, improper set up and use. Periodic maintenance is not covered. Warranty does not cover service requests for free replacement and/or recall parts. THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE AND EXCLUSIVE STATEMENT BETWEEN THE BUYER AND SELLER. SUPERA, LLC NEITHER ASSUMES NOR AUTHORIZES ANY PERSONS TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SAID EQUIPMENT. Example of items not covered under warranty, but not limited to only these items: 1. Acts of God, fire, water damage, burglary, accident, theft. 2. Freight damage. 3. Improper installation or alteration of equipment. 4. Use of generic or after market parts. 5. Repairs made by anyone other than a SUPERA, LLC designated servicer. 6. Lubrication. 7. Expendable wear parts, adjustable feet, blown fuses, lamps, etc. 8. Cleaning of equipment. 9. Misuse or abuse. Supera 2014 Version 1 October 2014
Supera Customer Care Toll-Free Service Line: 1-866-953-3288 For additional product and warranty information, please visit our website at: www.superaco.com