Checklists INFO@GREENKEYGLOBAL.COM GREENKEYGLOBAL.COM
Laundry In-house laundry is one of the most energy-intensive areas of a hotel's operation. Its use of energy per square foot may even surpass the kitchen. Heat loss, and ultimately energy loss, is the key element to consider when reviewing laundry operations. Refer to the following sections and checklists for suggestions on various ways this department can save money and reduce its environmental impact. Incorporate elements that are relevant to your facility into your operations and ensure staff understand the benefits that will ultimately be derived from such actions. GENERAL CONSIDERATIONS MACHINE MAINTENANCE Dirty machinery, motors, and fans operate inefficiently and use needless energy. Improperly fitting gaskets, poor insulation, and open floor drains all add heat and humidity to the room, increasing the air conditioning load (and cost). A proper maintenance program will eliminate these problems and improve working conditions. OPERATIONAL HOURS & BREAK PERIODS It may make sense to re-schedule your hours of operation. The hours between 10 p.m. and 6 a.m. are typically low demand times for energy. This time period can be used to schedule employees and help avoid high peak electrical charges. Heat is wasted when machines are idle. Staggering employee lunch and break periods can help keep machinery in continuous operation. STEAM A substantial amount of usable steam is left in the boiler and pipes at the end of the day. Unused steam is wasted money and energy. To prevent this, try the following steps: 1.! Shut the boiler down five minutes earlier than usual and observe the results 2.! Extend the time a few minutes each day 3.! Continue with this procedure until you reach an optimum early shutdown time that doesn't affect production or quality. Steam leaks can be costly. For example, a leaking steam trap with a 3/8" orifice on a 100 psi line can waste up to 470,000 pounds of steam/month. At a cost of $5 per 1,000 pounds, a leak can cost $2,350 per month or $28,200 per year. If steam, rather than liquid condensate, is passing through a trap, the trap is defective. Page 1
OPERATING PROCEDURES CHECKLIST Institute regular employee training on proper equipment use Do laundry during non-peak hours when less equipment and energy is being used in other areas Operate machines when full - they use the same energy whether full or not Sort dirty clothes according to type and soilage, and wash with the shortest adequate cycle Stop using phosphates and harmful chemicals Don't use chemical fabric softeners; instead, add a bit of vinegar to the rinse water Experiment with non-phosphate cold water washes; use cold water to wash whenever possible Don't use aerosol products. If you use starch, put it in pump dispensers Make your own non-chemical starch for the laundry by mixing one tablespoon of cornstarch to 8 oz. water and mix: much cheaper and just as effective Set hot water thermostats at the minimum level needed Sort clothes to be dried by type; dry with the lowest temperature and shortest adequate time cycle Don't use commercial, chemical-impregnated anti-cling products; a wet towel in the dryer does the same thing Use the extractor cycle correctly; it's more energy-efficient than heat drying Schedule dryers to operate continuously to make better use of the residual heat built up Clean lint traps at least twice a day Check lint build-up in other parts of the dryer daily Recycle all cartons, bottles, and jugs Send 'perc' cartridges if your laundry does dry cleaning Save and re-use clothes hangers Run irons as little as possible, minimize warm-up time, heat only to the minimum temperature needed, and turn off when not in use Shut down boilers at a practical time before the shift is over Immediately report any malfunctioning equipment, water and steam leaks, and/or clogged drains Never leave faucets running Cool laundry room with normal outside air when practical Turn off all lights and equipment when not in use MAINTENANCE CHECKLIST Washers Ensure control valves are working properly and not leaking. Check belt-driven models for tightness of belt and alignment of pulleys. Lubricate motor as needed; clean off lint, dust, and dirt. Page 2
Have your service representative clean and adjust gas model burners. Ensure washer timers are working correctly. Dryers Check heat recovery equipment, clean waste-heat exchangers, and periodically check efficiency. Check front-to-rear level of tumbler baskets or cylinders. An out-of-level basket axis can cause uneven loading which wastes energy. Check rotating speed of the tumbler at full load. If the speed is too low, fabric surfaces aren't being fully exposed to the drying air and energy is being wasted. Keep bearings on all rotating equipment well lubricated to reduce friction and resulting waste of energy. Check fan speeds in tumblers and dryers. If fans are operating below optimum speed, drying time takes longer. Ensure that burner gas holes on direct-gas-fired equipment are clear. Set all direct-gas-fired equipment at the manufacturer's recommended firing rate - higher or lower firing rates waste energy. Ensure all timers are operating properly. Extractors Ensure extractors and timers are working correctly; the more water removed by the extractor, the less the dryers must evaporate, saving both heat and energy. Ventilating, Cooling, & Heating Systems Check the laundry for negative pressure. Insufficient make-up air to satisfy the exhaust blowers can lead to faulty operation of tumblers and dryers and can cause incomplete combustion in direct-fired units, with a resulting waste of fuel. Take make-up air from outdoors rather than from air-conditioned spaces. Regularly clean or replace filters on ventilating units. Keep all exhaust and supply systems fan housings clean. Check proper operation of waste heat recovery units and correct leakages in waterfilled or glycol-filled systems. Clean heat exchangers, ductwork, and filters. Check for drainage from icing. Verify all timers, temperature controls, damper mechanisms, and valves. When using an air-to-air waste heat recovery system, duct the heated make-up air directly to process dryers, rather than back into the open laundry area. LIGHTING CHECKLIST Repaint with light colors only, to reflect light. Use natural light when possible, except when it interferes with temperature controls. Dirt can reduce lighting efficiency by as much as 50% so regularly clean fixtures, bulbs, ceilings, walls, and windows. Test effectiveness of cleaning by measuring a fixture's foot candles with a light metre before and after cleaning. Page 3
Have employees in each area help determine appropriate light levels. Each employee's light requirements are different, depending on their age and physical condition, and productivity can suffer if there is insufficient light. Install additional switches in areas that don't always require full lighting; only turn on those lights that are needed. Install fluorescent lights; they use 1/3 of the electrical energy used by incandescent. Replace existing fluorescent lighting with energy efficient tubes which use less energy with only a minor reduction in light output (e.g. replace 40 W tubes with 35 W and 75 W tubes with 60 W). In multiple-switch installations, color-code individual switches to identify which lights they control, and which switches to leave on or off. If possible, move switches so they're convenient and visible; employees are more likely to help conserve energy if it's easy. Install separate light switches to turn off lights in low-use or naturally lit areas, or connect them to timers. Use light switch stickers to remind staff to turn off lights when leaving a room. Replace resistance dimmer switches with solid state dimmers. Where practical, rearrange workstations to share lighting. Consider 'task lighting' for employee workstations. Use the minimum amount of light needed in your work area, and turn lights off when leaving the room for 15 minutes or more. Ensure that the maintenance department:! Checks automatic lighting controls daily! Cleans windows/skylights at least every three months Cleans lamps and fixtures at least every six months! Cleans ceilings and walls as required WATER CHECKLIST Drain and flush hot water tanks every six months to prevent efficiency-reducing scale build-up and deposits. Service gas or oil burners regularly. Test all thermostats regularly. Investigate the possibility of solar water. Solar water generally pays for itself within five years or less, after which it supplies 'free' hot water. WATER MAINTENANCE CHECKLIST Repair any leaks in the water piping system. Clean and recondition hot temperature mixing valves at least once a year. Check insulation on hot water pipes and storage tanks frequently. Flush hot water tanks every six months (or more frequently with very hard water) and remove accumulated solids and sludge. Remove exterior scale build-up from electric hot water heater coils at least once a year. Page 4
With immersion-type hot water heaters installed in the boiler shell, remove and clean scale from interior and exterior coil surfaces. Check water storage tank temperature controls every six months. Test all hot water controls and adjust if necessary. Check the steam trap on steam hot water heaters; repair or replace if leaking steam. HOT WATER & STEAM CHECKLIST Inspect systems frequently for leaks Test and adjust hot water heater controls to avoid overheating Check insulation on hot water storage tanks, pipes, and steam lines; insulate any hot spots Drain and flush hot water heater tanks semi-annually (more often with exceptionally hard water) Page 5